Search Documents

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

By A. Livingston

This paper on mining practice at the Fresnillo silver mines is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of North America. Two classes of ore are produced at Fresnillo. A low-grade oxidized silver ore; end a complex-base sulphide are containing gold, silver, lead, zinc, and copper. This paper is confined to a discussion of operations relating to the production of oxidized silver ores. To date, more than 10 Million tons of this ore rave been mined. The present (June, 1931) daily production is 2,000 tons of ore, and approximately 600 men are employed in the mining operations.

Jan 1, 1932

By M. R. Geer

All the coal lands in Alaska are publicly owned, and the Federal Government is the principal consumer of coal. Therefore the Government has long been concerned with the wise utilization of the coal reserves of Alaska as well as with the availability of coals meeting the specifications for use in various Government installations. Coal preparation plays a key role in both of these areas of interest. The proper choice and operation of coal-washing equipment permits the mining of inferior deposits, minimizes waste of coal in preparation, and assures a prepared product of the best quality obtainable from the raw coal. Thus, from time to time, the Bureau of Mines has made washability examinations on most of the coals mined in Alaska. Generally, these examinations were made when new mines or new beds were opened, when construction of new preparation plants was being considered, or when the operation of existing plants could be improved by better knowledge of the raw coal. The purpose of this report is to bring together all the washability data available on the coals of the Matanuska Valley and Beluga River fields. The pattern of energy development for the rapidly growing Anchorage area is not clear at this time. Formerly coal was the only fuel available for large-scale space heating and power generation. More recently both oil and natural gas have entered the market, and several hydroelectric projects have been completed. Additional major hydroelectric projects are being considered. The role that will be played by coal in this competitive energy market is uncertain. However I if coal is the fuel used in future power plants or industrial installations, the information contained in this report will be useful in indicating the quality of the coals that can be supplied and in selecting proper preparation techniques.

Jan 1, 1962

By Earle S. Burnett

This report outlines the experimental procedures for using a Burnett apparatus to obtain compressibility coefficients for multiphase, multicomponent fluid mixtures. The conventional Burnett method is described briefly whereby multiphase compressibility data can be obtained by first determining the compressibility factor, Z, as an isothermal function of pressure alone. Then starting at conditions of temperature and pressure where Z is known, the fluid is cooled at constant volume to some lower temperature at which the resulting pressure is measured, and a corresponding value of Z is obtained from a fundamental relationship between compressibility factors, pressures, and temperatures at constant volume. The isochoric treatment of the fluid, extended to still lower temperatures and along other isochors, eventually results in compressibility determinations for the whole two-phase system thus covered experimentally.

Jan 1, 1963

By J. F. Smith

A series of studies of emissions from large coal-fired steam generators have included measurements of the concentrations of oxides of sulfur and oxides of notrogen. The sampling equipment, method of sampling, and analytical techniques used for processing of these samples are detailed. A method based on the precipitation of benzidine sulfate was developed for determining both SO3 and total oxides of sulfur in the presence of interfering acidic components in the stack gases. In addition, difficulties encountered with sampling and analytical techniques are also described.

Jan 1, 1968

By K. K. Kelley

The heats of formation of two lead vanadates (Pb2V207 and Pb3V208) and manganese vanadate (MnV206) were determined by hydrochloric acid solution calorimetry, supplementing previous Bureau of Mines measurements of the vanadates of calcium, magnesium} and sodium. Heat and free energy data for 11 vanadates were assembled on a common basis. The stability of comparable vanadates (with respect to the oxides) increases in the following order: Magnesium, manganese, lead, calcium, sodium.

Jan 1, 1963

By Raymond L. Carpenter

The thermal conductivity, electrical resistivity, and Seebeck coefficient for nine compounds, based on the formula for enargite Cu3AsS3, were measured in a search for efficient materials to be used in thermoelectric generators or refrigerators. Results indicate that one of these compounds, Cu3SbSe4, has thermoelectric properties approaching those of bismuth telluride. An investigation of the effect of adding small quantities of tellurium to Cu3SbSe4 and Cu3SbS4 in order to improve their properties also was made. A figure of merit of 2.1 x 10-4 °C-1 was obtained for Cu3SbSe4 + 0.1 percent tellurium.

Jan 1, 1963

By F. W. Wood

A program of research was conducted by the Bureau of Mines to investigate anomalies in electrical-discharge behavior during consumable-electrode arc melting of titanium and to study the effects of these irregularities on arc-furnace explosions. A major effort was devoted to an experimental survey of arc behavior and a qualitative definition of discharge phenomena.3/ An important conclusion was that the "glow" of industrial arc-melting terminology is not a glow discharge but a skittering arc in a displaced position. The conditions that permit displaced skittering were tentatively defined. The displaced skittering arcs tended to damage melting crucibles in two ways, and details of possible mechanisms leading to crucible rupture and explosive reactions have been proposed accordingly. However, no acceptable means of preventing crucible damage was discovered.

Jan 1, 1961

By J. H. Holden, G. R. Strimbeck, L. F. Willmott, W. R. Huff

A pilot - scale fluidized feeder was developed for continuously feeding up to 1 ton of pulverized coal per hour to a pressure gasifier . Fluidization in the 3 - foot - diameter by 34-1 / 2 - foot - high feeder is effected by two streams of inert gas , a technique called zone fluidization . A stream of inert gas through a drilled plate in the base of a central column near the bottom of the feeder fluidizes the coal . Another stream through a drilled plate in the annulus between the central column and feeder wall provides a source of semifluidized coal for the central column . Fluidized coal from the central column discharges through an extraction funnel and discharge line . Zone fluidization provided good fluidization with moderate requirement for fluidizing gas . Instruments were developed for metering and recording the flow rate of fluidized coal . A system was developed for storing , and weighing pulverized coal , and then delivering it in fluidized form at about 1 to 8 tons per hour .

Jan 1, 1964

By W. L. Falke

Research was conducted to develop methods on a laboratory scale for recovering manganese from manganiferous slimes and limestones . The procedure is a low- temperature modification of the carbamate process , in which manganese is dissolved and the valence reduced by treating slimes and limestones with controlled amounts of sulfurous acid . Manganese ( II) hydroxide is precipitated and leached with ammonium carbamate solution , and manganese carbonate is separated by warming the leach solution . A major portion of the reagents is regenerated and recirculated . About 75 percent of the total manganese in manganiferous slimes , and from 50 to 75 percent of the total manganese in manganiferous limestones , are recovered as manganese carbonate containing 45 percent manganese .

Jan 1, 1964

By Beverly W. Dunning

The effect of vacuum melting on the elimination of gases and nonmetallic inclusions for six low-alloy steels was investigated. The purpose of these studies was the analysis and comparison of differences in gas content and inclusions in air-melted and vacuum-melted steel. Data obtained from melts of 1-1/4 to 20 pounds indicate that vacuum melting decreases the number and size of nonmetallic inclusions and at the same time increases the degree of dispersion of the remaining inclusions. These improvements are undoubtedly related to the elimination of approximately 80 percent of the nitrogen and 90 percent of the oxygen as well as most of the undesirable metallic trace impurities.

Jan 1, 1961

By J. A. Organiscak

The Bureau of Mines recently investigated dust generation and methane liberation during half-and full-web cutting at a double-drum shearer longwall face. This study was conducted to ascertain the health and safety aspects of wider web shearing at longwalls. Results from these underground tests showed that deeper web cutting reduced dust generation and methane liberation per ton of coal mined, while significantly improving shearer production rates. When cutting with the airflow (head-to-tail cut pass) full-web cutting decreased dust generation per ton by 16 pct at the shearer and 6 pct at the tailgate, with an increase in shearer production rate of 72 pct. Methane liberation per short ton also deere~sed by 36 pet at the shearer and 22 pct at the tailgate. Full-web cutting against the airflow (tail-to-head cut pass) decreased dust generation per ton by 41 pct at the shearer and 37 pct at the tail-gate over half-web cutting, with an increase in shearer production rate of 61 pct. Methane liberation per ton also decreased by 35 pct at the shearer and 41 pct at the tailgate. These improvements for full-web cutting are a reflection of improved cutting efficiency (less dust and methane produced from cutting) and less new face area exposed per ton of coal mined (less methane liberated from face per short ton of coal mined).

Jan 1, 1988

By R. E. Coleman

The molecular species occurring at the mineral-reagent interface of the galena-aqueous potassium ethyl xanthate system was studied by developing a technique for using an attenuated reflection method in conjunction with standard infrared spectroscopy procedures. Lead ethyl xanthate was detected from the infrared spectra of all galena surfaces treated in the pH range of 7 to 11. At pH 8.5, lead ethyl xanthate formed as a film chemically bonded to the galena surface. A solvent extraction sampling method was employed with infrared spectroscopy to obtain quantitative data on the lead ethyl xanthate removed from the galena surface. The data showed that between pH 7 and 11 thy quantity of lead ethyl xanthate physically adsorbed decreased as the pH was decreased; in the same pH range, the quantity of free lad ethyl xanthate in the aqueous medium remained constant, and the amount of unreacted xanthate varied.

Jan 1, 1966

By Otto Ruhl

As the result of a study of an area comprising some 100 square miles in the Missouri-Kansas Zinc district known to have produced zinc Ore from horizons below the Grand Falls formation, it was concluded that these horizons could become an important future source of zinc. To test this conclusion and to ascertain the general conditions associated with these lower-horizon ore deposits, the Bureau of Mines undertook detailed drilling of localities thought to be favorable for deposition of ore in the Reeds Spring and. Fern Glen formations. Two sites in the Galena, Kans., mining camp were chosen for this purpose. Ninety churn-drill holes totaling 19,338 feet of bore were completed by the Bureau in two campaigns that extended from October 1944 to June 1946. Approximately 25 percent of the holes encountered ore and indicated three separate ore bodies containing substantial tonnages. Observations made during the course of the work revealed that certain structural conditions are common to ore deposits in the Reeds Spring and. Fern Glen formations.

Jan 1, 1949

Oil from shales has long been a source of fuel in foreign countries; however, in the fuel economy of the United States this source is classed as a reserve for future needs. In fad, shale oil has never been produced here in quantities necessary to establish oil-shale utilization as a sustained industry. The first known resources of stored energy that man endeavored to utilize were probably wood and water, and from these he directly obtained heat and power, respectively. With the evolution of man came the search for and the development and use of other natural fuel resources, the series progressing through the solid, liquid, and gaseous fuels until today those of one type can be converted into another, depending upon the use for which they are intended. The most important fuels are those that appear naturally in the most concentrated, conveniently obtainable, and usable forms. With the discovery of each new and more concentrated fuel there has been an appreciable increase in the importance of and number of devices for converting these fuels into energy.

Jan 1, 1938

By E. P. Youngman

Great Britain has never had a basic raining law such as is in force in most foreign countries. This lack may be due to the fact that, with the exception of gold and silver, all metals or minerals belong to the owner of the surface land. Even with respect to the precious metals, gold and silver, which are not abundant in Great Britain, the right of the Crown, though still technically acknowledged, is not always insisted unon. All other metals and minerals are vested in the ground landlord, who may sell, lease, or other¬ wise convey them. The State has little to do with the mining industry except in. regulatory and judicial matters. The Government must settle controversies and provide for easements, rights of way for railroads, roads, and canals, or, in general, effect the same control that it exercises over other industries. As mining was carried on in very early times in England, of necessity a certain legal procedure came into existence, which in effect was little more than a private contract between the owner of the mineral (whether an individual or the State) and the miner. The nature of such contracts, of course, has changed radically with the changed relations between classes, as England lias developed from the feudal into the modern State. From the medley of ancient procedure and custom, a concession system of mining in^its simplest form lias evolved. Of the earlier conditions. Van Wagenen says

Oct 1, 1931

By William H. King

The Nevada Massachusetts tungsten deposits (fig. 1) are in the Mill City Mining District in north-central Pershing County, Nev., about 37 miles southwest of Winnemucca. Contact metamorphism of thin limestone beds within a series of metamorphosed sedimentaries formed scheelite-bearing ore bodies. These deposits are distributed over a wide area. A Bureau of Mines development program was started January 11 d was completed on July 25, 1941. This work was centered on the outer and less explored beds in the district and comprised trenching, sampling, and diamond drilling. Exploratory work was done in cooperation with the U.S. Geological Survey. Project work substantially increased the reserve tonnage of marginal ore in three of the areas explored and proved the nonexistence of tungsten in a fourth area. The following pages summarize the history of the district, outline property ownership, and describe physical features and ore deposits. The plan and results of the work performed by the Bureau of Mines are presented along with geologic and topographic maps, assay maps, and diamond drill-hole logs.

Jan 1, 1950

By R. L. Lincoln

The effects of adding from 1 to 50 atomic percent (a/o) to vanadium were investigated by the Bureau of Mines. Properties studied included as-cast and annealed hardness, microstructure, fabricability at room temperature and elevated temperature, tensile strength, electrical resistivity, and oxidation resistance at 625° and 800° 2. Additions of small amounts of hafnium resulted in lessened as-cast hardness, decreased electrical resistivity, impaired roll- ability, increased oxidation resistance, and greater tensile strength. Larger amount of hafnium caused greater as-cast hardness, increased electrical resistivity, further impaired rollability, continued increase in oxidation resistance, and lessened tensile strength. INTRODUCTION The purpose of this study was to determine the effect of hafnium additions on the properties of vanadium and to learn if this binary alloy had any special or unusual properties. This investigation is a part of a larger research project in which new and expanded uses of vanadium are being sought. Domes tic vanadium is found frequently in combination with uranium, and because of the demand for uranium as a nuclear fuel, there now exists a surplus of vanadium-bearing minerals and vanadium pentoxide as a byproduct of uranium production. Primary principles of conservation demand that greater use be made of this readily available surplus; finding suitable metals to alloy with vanadium to enhance its properties is one way to increase its utilization. This report is the result of an investigation of the effects on the properties of vanadium when hafnium is added in amounts from 1 to 50 a/o.

Jan 1, 1962

By J. G. Schoning

The Holmes Safety Association is an offspring of the Joseph A. Holmes Safety Association which was organized in Washington, D. C., in 1916 at a meeting of representatives of twenty-four leading mining associations connected with every branch of the United States mineral industries. The purpose of the meeting was to do honor to the memory of Joseph A. Holmes, one of the founders of the United States Bureau of Mines and its first director, whose death had occurred the year before on July 12, 1915. In deference to what was believed would have been the expressed wish of this great humanitarian and benefactor of the mineral industries, it was decided to establish a national safety organization to cover the mineral indus¬tries exclusively; out of respect for his memory and service, the organization was named the Joseph A. Holmes Safety Association. On receiving requests from several mining districts, in 1922 a number of chapters ware established in several mining States.

Jan 1, 1929

By M. Hertzberg

This Bureau of Mines report proposes a new methodology for estimating industrial dust explosion hazards in terms of three probabilities or co-factors: The dispersion of the dust, the existence of a flammable dust concentration, and the presence of an effective source of ignition. This method or rationale is proposed as a replacement for the "explosibility index" that was first suggested 25 yr ago, but which, by consen-sus among leading researchers in the field, is now outdated. This report presents a detailed critique of the deficiencies of that old, material-oriented index, and develops the logical rationale for its re-placement by an approach that is better suited for quantitative hazard evaluations. A variety of such evaluations are illustrated, which show how a quantitative prediction of explosion frequencies can be obtained from laboratory measurements and operating conditions in a given indus-trial facility. The method has some pitfalls, particularly as they re-late to the correlation of events or their randomness. These are discussed, as well as the method's other limitations and uncertainties. This work is intended to provide a beginning to a quantitative approach to explosion hazard assessment. To that end, a new method is proposed for estimating thermal ignition probabilities in terms of the measured laboratory autoignition temperature of a dust, its relationship to the operating temperature, and its distribution within a given industrial system.

Jan 1, 1987