Search Documents

By M. J. Beus

The Bureau of Mines, under a cooperative agreement with Hecla Mining Co., is conducting a rock mechanics study of the 6,200-ft-deep circu-lar, concrete-lined Silver Shaft in northern Idaho. The objective of the project was to instrument and evaluate lining behavior and rock de-formation when a deep shaft is constructed in a high in situ stress field and anisotropic rock mass. Rock mass displacements were moni-tored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. Field data from the 5,955-ft test level show that rock displacement is controlled by rock mass anisotropy. Liner stress and strain levels reflect the high in situ stress field as well as nearby station and raise construction. Maximum stresses measured in the lining, as a result of shaft excavation, are about one-third of its compressive strength. Subsequent loading pocket excavation resulted in signifi-cantly increased stress and strain levels in the liner. Continued monitoring and preliminary analysis of the data indicate that concrete-lined, circular shafts are stable for the high, unequal horizontal stress fields and rock anisotropy encountered in deep-level mining. Adjacent development work can be expected to significantly alter the initial stress and displacement conditions.

Jan 1, 1984

By J. W. Thompson

OIL AND GAS AS MINERALS. Oil and gas within the ground are minerals and the fact that they have attributes not common to other minerals because of their fugitive nature or vagrant habit, and the disposition to percolate, and the possibility of their escape from beneath one part of the surface to another, does not remove them from the class of minerals. Texas Co. v. Daugherty (Texas), 176 Southwestern, 717, p. 719, May, 1915. OWNERSHIP OF TAILINGS-ABANDONMENT. A corporation engaged in milling- and the reduction of ores deposited the tailings therefrom upon a portion of its own land lying in a gulch through which water flows at times in great volumes and with great force' and notwithstanding all reasonable efforts by dams and otherwise to retain its tailings, the tailings eventually were forced upon the lands of an adjoining owner; these tailings were valuable and their retreatment, intended by the mill owner, profitable; and the fact that the tailings were so washed down upon the lands of the adjoining owner and permitted to accumulate and remain for some considerable time is not sufficient to show an abandonment on the part of the owner of the tailings, where it is clear that the owner had no intention of so doing, but on the contrary, always intended to conserve and retreat the tailings.

Jan 1, 1916

By Albert L. Toenges

A phase in strip mining of bituminous coal is the overturning of the surface of the land. The purpose of this report is to acquaint the operators and others interested in stripping with the work that has been done in certain States to reclaim the surface of land from which the coal has been removed by this method of raining. The preparation of this manuscript follows an extensive study of the subject in the field in the course of which a large number of strip mines were visited. ACKNOWLEDGMENT The information used in the report was obtained through the courtesy and cooperation of the operators of the mines visited, State officials and educational institutions, and others interested in the subject.

Jan 1, 1939

By Robert H. Peters

The U.S. Bureau of Mines has prepared this report on strategies for maintaining high job attendance among underground coal miners because high absenteeism is a threat to miners safety and seriously hampers productivity. A substantial number of research studies on the effectiveness of various strategies for reducing absenteeism among the employees of nonmining industries have been reported in the literature. These strategies have aimed at improving job attendance through one or more of the following: (1) improving employment procedures, (2) overcoming problems that adversely affect one's ability to attend work, and (3) increasing miners motivation to attend work. Many of these strategies appear applicable to the mining industry, and are reviewed in the first half of this report. The second half of this report describes how one could develop and implement a program for maintaining high attendance at underground coal mines. The steps include: measuring and evaluating attendance levels; formulating attendance goals and an absenteeism policy; developing and implementing an attendance promotion program; and periodically going through the preceding steps known as recycling.

Jan 1, 1989

By J. M. Singer

In this Bureau of Mines study coal and rock dust beds were entrained by airblasts generated by gas explosions at the closed end of a 0.61-m-diameter explosion tunnel, 49.7 m long. The system was designed to simulate entrainment of mine dust deposits by accidental gas explosion at the coal face of nonintersecting mine passageways. Full-scale mine explosion trials confirmed many of the results of the explosion tunnel experiments and indicated several new features of dust entrainment. Dispersal of 20.3-cm-long stepped dust beds located 35 m from the closed end always began during the early portion of the ascending gradient of the first transient airflow (and pressure) wave, and was usually completed before the end of the first quarter-wave period. Bulk quantities of dust were entrained simultaneously by longitudinal regression from the leading edge of the dust bed and by surface lifting of the top layer. Instantaneous threshold air velocities for bulk quantities of coal and rock dust beds in separate, mixed, and layered configurations were in the same range (5 to 30 m/sec) as previously found under steady-state velocity conditions. Selective lifting of coal dust layers from rock dust occurred when the threshold dispersal velocity of coal dust but not of the underlying rock dust was exceeded.

Jan 1, 1976

Ecuador a gross domestic product (GDP) grew 8% despite a slowdown in production and sales of petroleum, the dominant economic sector. Crude petroleum exports, which amounted to about 35% of total exports in 1977, were valued et $484 million,2 a decrease of 14% from 1976 values. Petroleum export sales were depressed because foreign buyers were somewhat uncertain that State-owned Corporación Estatal Petrólera Ecuatoriana (CEPE) held legal title to the oil until final settlement with Ecuadorian Gulf Oil Corp. In addition to the legal complication, Ecuador maintained a relatively high export price for oil until late in the year. There was also a shrinkage of traditional U.S, markets owing to the Alaskan pipeline becoming operational and an increased availability of Mexican supplies. The export market was also affected by increased domestic production in Peru and Chile, which lessened their import needs, and the pressure of greater competition from the Middle East in supplying crude oil to Caribbean refineries. About 20.4 million barrels or 40% of Ecuador's total crude exports went to the United States. Only 27 wells were drilled in Ecuador during L977; of these, 16 produced oil, 3 were dry holes, and 8 were suspended. About 31 wells were planned for 1978. Three new oilfields were discovered during 1977; two by CEPE in northeastern Ecuador and one by the Argentine State oil company Yacimientos Petraliferos Fiscales (YPF), operating in Ecuador under a service contract. CEPE's two discoveries tested at 5,000 and 1.450 barrels per day, respectively. The YPF discovery tested at about 1,000 barrels per day. Ecuador altered its position regarding

Jan 1, 1981

By Nicholas Kyriazi, John P. Shubilla

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory, has undertaken a study to determine how well self-contained self-rescuers (SCSRs), deployed in accordance with Federal regulations (30 CFR 75.1714), hold up in the underground environment with regard to both physical damage and aging. This report presents findings regarding laboratory-tested SCSRs in the sixth phase of testing from mid-1996 to early 1998. The SCSRs were tested on human subjects and on a breathing and metabolic simulator. These results indicate that most of the apparatus, if they pass their inspection criteria, perform satisfactorily. However, the deployed CSE SR-100s exhibited significantly higher inhaled CO2 levels than new units, as in the previous phase. This will cause higher ventilation rates in most users, which will, in turn, result in higher breathing pressures, possibly causing users to prematurely remove the apparatus. CSE Corp. has developed a noise test that can identify apparatus suffering from chemical-bed degradation causing the early CO2 breakthrough. This test was added to the inspection criteria for the SR-100. In addition, several of the MSA Portal-Packs that passed their inspection criteria were found to have KO2 dust in their mouthpieces. Further investigations by NIOSH and the Mine Safety and Health Administration confirmed these findings, which resulted in the decertification of the apparatus and their removal from service.

Jan 1, 2000

By Alvin Kaufman

Following the gold discoveries of the late 1800's much was written regarding the vast mineral resources of Alaska, and much interest was aroused, and yet over the years little has been done to exploit those resources. Between 1906 and 1935 the Kennecott copper mines of the Copper River region were the keystone of the mineral economy (fig, 1). After the depletion of the Kennecott ore reserves and aided by the statutory rise in the price of gold, the yellow metal became the major mineral commodity. In recent years it has shared the honors with coal and sand and gravel. Although this trend should indicate the development of a stable, diversified mineral industry, yet the trend of production is downward. This report results from a study by the Federal Bureau of Mines to delineate the problems and to forecast the growth of the mineral industries in Alaska. The need for such a blueprint for the future was enhanced by the population explosion in the United States and the consequent eventual need for additional living space, as well as the current interest in new areas, and the necessity to develop reserves of strategic minerals.

Jan 1, 1961

By R. S. Dean

The brief resume of the activities of the Metallurgical Division that appears annually in its progress reports series serves a useful purpose by making available a rather comprehensive but concise recapitulation of the current work, and publications of the division. An unprecedented opportunity to attack the problem of producing ferro-grade material from low-grade domestic manganese ores effectively was provided by the act designated as Public 667 of the 76th Congress of the United States, approved June 26, 1940, which made available an appropriation for "Expediting Production of Equipment and. Supplies for National Defense." Although the funds were not immediately available to the division, good progress has been made in the, solution of the many and diverse problems presented in the studies undertaken to determine the best methods for the recovery of useful products from a wide variety of manganese ores.

Jan 1, 1941

By R. L. Marovelli

ANTICIPATING the eventual use of the huge tonnages of nonmagnetic taconites of the Mesabi range of the United States, the Federal Bureau of Mines is classifying and evaluating these deposits in detail. This introductory report describes work begun in 1954 as part of a long-range program to sample, classify, and evaluate important occurrences of nonmagnetic taconite on the Mesabi, range. Included in this report are brief discussions of the geology, history, and potential of the Mesabi range district and mining industry, together with a more detailed presentation of the sampling and metallurgical evaluation of these nonmagnetic taconite deposits. A total of 898 field samples was collected. Most of these were taken in the region between Grand Rapids and Chisholm, Minn., but a few came from the area between Chisholm and Buhl, Minn. Of the total samples, 865 were from open pit bank faces where the greater vertical distances presented by the cherty members facilitated the taking of a large number of samples. Conversely, the narrow face presented by the slaty members confined and limited the areas from which samples were taken. In addition, 33 of the field samples were taken from rock dumps in order to determine, in a preliminary way, the characteristics of these materials.

Jan 1, 1961

This report summarizes the cost of U.S, mining and milling industry compliance with the Environmental Protection Agency (EPA) interim water quality guidelines for waste discharges. Applicable excerpts from Public Law 92-500 are stated and interpreted in conjunction with the guidelines being used for implementation of the law. Over 200 U.S. Army Corps of Engineers applications for discharge permits were used to develop the quality and quantity data base needed to estimate the cost to comply with EPA guidelines, Cost of three basic treatment methods were considered: Aeration, addition of lime, and sedimentation. From the process design, cost-capacity graphs were developed to consider maximum flow rate, maxi lime addition, and average flow rates. The graphical method used in this evaluation should provide a reasonable guide to the effect of waste treatment and, therefore, Public Law 92-500 and corresponding EPA guidelines on the mineral processing industry. The cost of complying with the EPA guidelines will have the effect of prompting the mining industry to minimize the production of waste water and of undertaking some additional treatment, Two case studies are presented to illustrate efforts that might be fruitful for minimizing waste water production and for treatment of combinations of acid mine drainage, mill wastes, and metallurgical process wastes when treatment is deemed necessary.

Jan 1, 1975

By E. L. McHugh, R. T. Mayerle, J. M. Girard

Ground control problems at surface mining operations can occur for a variety of reasons. Stress, gravity loading, rock strength, geology, pore pressure, weather effects, underground workings, and many other factors contribute to slope instabilities that range from small rock falls to massive slides of material. While some of these failures can be predicted or controlled by preventive measures, each year many completely unexpected failures occur. Current methods for monitoring generally involve measuring displacements at a few, selected points in and around the suspected area of instability. While most of the displacements along these points will be in a downslope direction, freeze-thaw cycles of water-filled joints, horizontal stresses or pressure, buoyancy in saturated soils, human measurement errors, or other situations can produce deformation in almost any direction, even without any instability in the slope. Determination of which, if any of the observed movements represents a potential hazard is essential. Because of the enormous surface area of many large open-pit mines, several varieties and scales of instability can occur. Small, unexpected rock falls may indeed be more hazardous than a massive failure that involves slow displacement of material over a longer period of time. Complete vigilance to detect all small potential falling blocks is neither feasible nor economical and certainly is not attainable using today's most common point displacement monitoring techniques. As part of an on-going study at the Spokane Research Laboratory, several new methods for monitoring slope instabilities are being investigated. This paper describes the potential adaptation of systems such as interferometric synthetic aperture radar, imaging spectroscopy, and time-domain reflectometry, to slope monitoring and design.

"These tentative coal mine inspection standards have been prepared as a guide for the Federal inspection of coal mines of the United States. Much time and thought have been spent by various members of the Safety Division in the preparation of thses standards, and it is believed that compliance with them eventually will be possible in most mines. In many instances objections will be raised to them owing to long-established mining customs and practices that are inherently of dubious safety and to a natural inclination to oppose change. In other instances there will be valid objections due to conditions not foreseen at the time these standards were prepared. Or there may be substandard conditions and practices due to original mine layouts that it is not practicable to change during the lifetime of the mine; in such instances it is likely that some effective measures are or can be taken toward lessening hazards.With the rapid change in mining methods some of the standards may become inapplicable and it may be advisable to revise them to meet the new conditions. Therefore, questions regarding these standards and suggestions regarding new standards should be brought to the attention of the supervising engineer of the Coal Mine Inspection Division so that modifications of and additions to these standards may be made from time to time.In many respects these standards exceed the provisions of the various State mining laws, and some may conflict with the laws of some States. In cases of conflict, the intent is not to advocate noncompliance with State laws but to suggest that it may be desirable for the State to reconsider such laws or safety orders.Although an effort has been made to word these standards so that they may be readily understood, nevertheless, a reasonable interpretation should be placed upon them. In fact, in numerous instances the words reasonable"", ""suitable"", and ""properly"" are used in recognition of the fact that reason- and sound judgment enter into the carrying out of the safety endeavor.The policy of the Bureau on some vitally important safety matters in mines is set forth in its published Safety Decisions. These decisions have been consulted and used in the preparation of these standards. These decisions also are now being reexamined by its Mine Safety Board."

Feb 1, 1942

By B. K. Shibler, W. G. Sandell, G. M. Potter, H. D. Snedden

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, examining 'engineers of the Bureau of Mines collected samples from seven manganese properties in Grand and beery Counties, Utah. These were supplemented by five samples submitted by property owners. Since all of the ores were too low-grade for use in producing ferromanganese for steel manufacture, some means of beneficiation was required to produce marketable concentrates, and metallurgical studies were made on each of the samples.Most of the ores Investigated are similar in one respect: At least part of the 'manganese oxide areas contains minute inclusions of gangue. This occurrence materially enhances the complexity of the ore, partly by .increasing the complexity of mineral association, but largely through making manganese-quartz liberation more difficult. In such ores, there is a marked tendency for the manganese minerals to be retained as shells or coatings on the surfaces of quartz particles when crushed. Particles of this type represent considerable loss of manganese in tailing, if gravity-concentration methods are employed, or tend to' float, thus carrying an appreciable quantity of gangue into the concentrate, if treated by flotation.Plus 48-percent manganese sinters were made from some of the ores tested, but, in general, intimate association of manganese minerals with silica limited the degree of beneficiation attainable."

Dec 1, 1947

By David Schlain

The Bureau of Mines investigated methods for electrodepositing platinum-group metals from molten cyanide baths. The preparation of thick, protective coatings on molybdenum, Inconel, graphite, stainless steel, copper, and other structural metals were studied, as well as the electroforming of platinum and iridium crucibles. Iridium, rhodium, and ruthenium can be electrodeposited under an inert atmosphere, while platinum and palladium require the presence of air. Electrolytes may be prepared by direct-current electrolysis in NaCN or mixtures of NaCN and KCN using anodes of the particular platinum-group metal. When the concentration of metal increases to about 0.3 or 0.4 percent, the deposits become bright, adherent, and coherent. Current densities may be 10 to 25 ma/cm2, and plating rates are often 0.5 mil/hr. Platinum and palladium baths deteriorate because of the oxidation of cyanide to cyanate and carbonate, and the precipitation of metal. Changes in the platinum cyanide bath are relatively slow. The protection against oxidation afforded by the platinum-group metal coatings is evaluated by testing encapsulated specimens in a thermogravimetric balance. Surface pretreatment and the use of undercoats are discussed.

Jan 1, 1977

By H. S. Benson

This report documents, from concept through field testing, the pan scraper Wheel Slip Monitor. The function of this device is to instantly warn the scraper operator of wheel slip and thus enable him to take immediate corrective action. Knowledgeable pan scraper people recognize that the preponderance of scraper tire damage and wear occurs during useless wheel slip when the scraper operator attempts to increase machine draft beyond what traction will allow. The resultant shortened tire life has become very expensive. The Wheel Slip Monitor reported here provides the means for relieving the scraper operator of attempting to judge wheel slip on tires he cannot see. Direct and intuitively understandable audible and flashing light warnings tell the scraper operator which wheel is slipping and also indicate the relative magnitude of the slip. Beside the Wheel Slip Monitor's patent utility as a real time operator aid, it has unique potential for application to extended term wheel slip history acquisition under field conditions. This information has never been easily available and it promises practical value in pan scraper management.

Jan 1, 1983

By W. T. Wertman

LABORATORY research has been started at the Bureau of Mines Morgantown Petroleum Research Laboratory, Morgantown, Va., to investigate the possibilities thermal-recovery methods for producing crude oils of high API gravity found in oil reservoirs of the eastern United States. This bibliography on thermal methods of oil recovery was compiled as a part of the work. Crude oil discoveries to December 31, 1958, in the United States were estimated to exceed 270 billion barrels. Cumulative production of crude oil through 19.55 was about 60 billion barrels, and the American Petroleum Institute estimates that an additional 30.5 billion barrels are economically recoverable by present methods. On this basis, about two-thirds of the oil that has already been found can be classified as economically unrecoverable for lack of a satisfactory method. The rap icily rising costs of proving new deposit; of domestic petroleum, the lack of new discoveries of large oilfields in the united States, and I he growing demand for crude oil have caused an acceleration of research to develop new or improved methods fur producing "unrecoverable" oil in known reservoirs.

Jan 1, 1960

By Paul S. Goodman

Volume II The purpose of this study is to explain reasons for the productivity differences in mining crews. The literature on group productivity is examined. Then a new approach to estimating productivity differences is proposed and estimated across seven different mines. The results indicate a fairly robust model in terms of explanatory power. Recommendations on how the model can be used as a managerial tool are presented.

Jan 1, 1985

By Daniel Ng

The U.S. Bureau of Mines-Michigan Technological University mine ventilation mainframe program was successfully adapted for execution in a personal computer (PC). The hardware requirement can be as modest as 256 kilobytes (33) of random access memory (RM) and two floppy disk drives. A version compiled for a PC possessing 512 Kb RAM has arrays dimensioned to accommodate 512 separate mine airways and junctions, and it contains all the features and capabilities of the original version. It has successfully analyzed all the ventilation networks tested, including a very large commercial mine (404 airways, 237 junctions, and 5 fans). In all cases the PC version produced practically identical results as obtained from the mainframe computer. In all respects, the PC version performed the same as the mainframe version with the exception of execution speed When a numerical coprocessor is employed, execution time can be reduced by more than 50%.

Jan 1, 1989

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989