Search Documents

By L. L. M. Kadnuck

The U. S. Bureau of Mines studied the suitability of using flexible tendon cable supports as secondary roof supports at a western coal mine. The supports were installed in longwall tailgate entries and grouted into the mine roof. This paper quantifies how the use of cable supports can improve ventilation in underground airways. A mine ventilation simulator was used to model the changes in airway resistance and airflow and show potential for further ventilation improvements when cable supports are used. Model results indicated that cable support use translated to savings in air pressure around the longwall panel and increased airflow at the longwall face.

Jan 1, 1994

By A. K. Clarke

In any treatment process that requires a coarse feed material to be reduced to a fine size by crushing and/or grinding it must be determined whether a wet or dry comminution system should be utilized. All factors must be evaluated in reaching the decision. Among these factors are: 1) Ecology and Plant Environment: Unfortunately in many instances the decision on wet or dry is based on prejudice resulting from an unnecessary fear of dust. The writers submit that this fear, although once justified, is no longer valid because technology and equipment is now available to collect dust to meet any standard. When dry grinding is used it is very often possible to discard a portion of the waste product in a dry state. This will decrease the size of the tailing pond required. As pollution control standards increase it becomes increasingly difficult to clean up water from tailing ponds. 2) Operating Costs: Steel wear is often five or more times greater in wet grinding than in dry grinding. This is mainly due to corrosion. The evaluation of the economics of dry grinding must of course include the air system and dust collection; similarly in a wet grinding plant related pumping and material handling costs should be included. Pumping costs are often overlooked. This assumes water is made to flow for nothing. Pumping can account for 20 percent of the power consumption in the grinding plant. Large scale comparative tests were conducted in a wet and dry commercial plant in 1970. The same ore was used for both tests. With all factors included in both plants the dry system showed lower horsepower per ton.

Jan 1, 1971

By M. Z. Emad, M. U. Khan

"Coal mines opting for longwall mining or its variations rely on the main and tail gates for production. Stability of these entries or crosscuts is crucial in coal mining operations. Roof or strata failure can be fatal, may lead to property loss and delay in production. Failure of the gates depends upon many factors including the mining method, panel dimensions, pillar width, mine depth, caving rate, dimensions of gates and roof strength properties. In Pakistan coal is mined through a variation of longwall mining method with almost no mechanization while using timber as a primary support. Timber support as chock is very useful in coal mines especially in overhanging face. Similarly gate entries and coal faces are supported by chock supports throughout their length. In this paper the stability of the longwall gate is assessed for a typical coal mine in Pakistan by using finite element code. Numerical modelling considerations for gate entries are discussed. A model parametric study is performed for key factors. The results showed that the existing mining practice is not suitable and there is a need to review the mining approach. INTRODUCTION Main and tail gate entries leading to longwall mining panel play a crucial role in production cycle. Failure of any of these may lead to loss of life, property and production delays. The stability of gate entries depends primarily on the nature of loading and stresses incurred. It is relatively easier to assess the ground response to production for common longwall mining panel. In thin-seam coal mines the gate entries are generally supported throughout their length by timber made chock supports. The tailgates receive huge deformations and stresses during the mining and backfilling cycle. The chock supports are required to take care of rock falls leading to blockage of entries causing production delays and loss of capital. A number of supports are available for supporting the gate entries (Hoek and Brown 1980; Brady and Brown 1985). The support system can be selected based on load-deformation characteristics including the yielding behavior, pre- and post-yielding behavior (Barczak, 2003). The principal of support selection is that the support characteristics must match the ground response in order to maintain the gate entries (Mucho, et al., 1999). It has been observed that thin-seam mining (<1 m) is very challenging and it is necessary to develop an understanding of ground mechanics before the selection of an efficient support system Dolinar (2003). The chock supports have been tested for load-deformation characteristics in the laboratory (Barczak 2003). But the ground and support interaction, response and loads must be assessed for individual site. This can be accomplished by in-situ testing and observations at few locations. The generated data is generally insufficient for complete understanding. Numerical models can combine the data generated in the laboratory and on-site to fulfill the requirements."

Jan 1, 2017

By S. Phillipson

The Mine Safety and Health Administration’s Roof Control Division (RCD) evaluated the use of Shuttle Radar Topography Mission (SRTM) data to identify fracture traces on Earth’s surface. Results were compared to the analysis method employed by RCD for 30 years, which relies on LANDSAT-TM Band 4. SRTM elevation models are expected to provide a direct representation of bedrock surface, while LANDSAT-TM Band 4 represents reflected near-infrared radiation as an indication of moisture content and is only a proxy for possible structures. Three areas in southwestern Pennsylvania were chosen for ground-truthing lineaments derived from both methods, following a series of desktop comparisons in six areas of the contiguous U.S. Field studies that identified numerous instances in which SRTM lineaments corresponded with joints at the projected location, and were oriented within 10° of joint strike, indicating that those SRTM lineaments represented the structural grain of the area. In some cases, lineaments were associated with individual joint zones. Photo-lineaments derived from the existing LANDSAT-TM methodology appear to offer a higher coincidence with expected trends of joints on a regional scale when performing the desktop comparisons, while field observations indicated that SRTM-derived lineaments had a higher association with individual geologic structures in the case study field area. It appears that both methods can identify the structural grain of an area, and that both tend to identify linear segments of valleys where erosion has preferentially occurred along joint zones or other structures.

Jul 1, 2023

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By Lennart Bergstedt

Boliden Aktiebolag, the prime base metal mining company of Sweden, annually treats some 11-12 million tons of sulphide ore in nine concentrators. Its first flotation plant was established in the early thirties for the complex Boliden ore. Since then, the number of mines and plants has gradually increased. Considerable effort has been devoted to the development of all phases of the technology of ore prospecting, mining, milling, smelting and refining. This has been necessary due to the complex and low-grade ores. The development of concentration has mainly been directed toward the arts of grinding and flotation. During the forties and fifties, open-stage fine crushing followed by two-stage grinding in rod and ball mills with cyclone classification was successfully introduced and used throughout the plants. The increasing cost of grinding media led to studies of an autogenous grinding technique as early as 1945. Basic test work commenced during the early fifties, with a. number of ores tested for pebble grinding. In 1956 a new pilot plant was built, with equipment installed for the continuous testing of pebble grinding and, later, for primary autogenous grinding of run-of-mine ore. The intensive test work showed that pebble grinding was feasible in almost all of the plants. At this early stage of testing, however, the merits of autogenous grinding could not be fully evaluated. As a. consequence the rod mill/ball mill grinding systems were converted to rod mill/pebble mill systems whereever possible. In parallel with the converting of grinding systems the development work concerning the merits of autogenous grinding went on. The major result

Jan 1, 1977

By T. C. Bibb

Longwalls using shearers in seam heights of less than 1.2 m (48 inches) are relatively rare in the U.S. Westmoreland Coal Company is currently operating a shearer-equipped longwall at a cutting height of 1.17 m (46 inches) in its Bullitt Mine. This face has averaged 2795 metric tons/day of operation since its startup on April 3, 1984. Longwall productivity in thin seams is substantially impacted by equipment reliability and availability of useable working room for travel and access. This paper addresses the design criteria used in selecting this face equipment, with the goal of maximizing these two parameters. Equipment discussed includes shearers. face conveyor, shields, stageloader, and emulsion system.

Jan 1, 1985

By Frank C. Stevens

The availability, cost and use of fuel and electricity for the cement industry is difficult to predict with a great degree of accuracy because the historical pattern of factors affecting energy was disrupted during the years 1972, 1973 and 1974. Forecasting is both an art and science and is based on .the premise that the best indicator of the future is the past. Statistical data is used to guide economists and businessmen in their predictions of the future. Even though the energy picture is changing, it is believed that electricity and fuel will be available for the cement industry in the foreseeable future, and this energy will be more costly in relation to the other items that are part of the manufacturing costs for portland cement.

Jan 1, 1977

By G. E. Sreedhar, R. Kumar

The pockets of high silica blue dust across the entire high grade hematite deposits in the Bailadila sector bothers the excavation activity due their iron content, which is higher than the threshold value specified by the Indian Bureau of Mines and the agony of stacking them separately due to their fragile & powdery nature. The physical nature of blue dust and its negligible alumina content makes these a potential source of hematite, which is a blessing in disguise. As most of the particles are in the form of an independent grain making it appropriately suitable feed for dry magnetic separation and thus the dry beneficiation has turned a bane into boon by enabling to produce concentrate either suitable for using as DSO or amenable for blending. The emphasis on carrying out dry beneficiation studies in the present context serves the purpose of mineral conservation, mitigates the issues of excavation and stacking as well as conservation of water resource. This paper describes the laboratory and pilot scale dry beneficiation studies carried out on blue dust of 48 – 60%Fe and Silica up to 30% at 25 Kg/hour to 400 Kg/hour, resulting in production of concentrate assaying 60 – 65%Fe. INTRODUCTION High silica blue dust (HSBD) is associated with Banded Hematite Quartzite (BHQ) and is available in abundance in various pockets across the Iron ore body in the Bailadila region of Chhattisgarh state. High Silica Blue dust occurs in the form of free granular particles and also as friable lumps. The chemical quality of this falls under sub-grade category (45 – 55%Fe) and as per the guidelines of Indian Bureau of Mines, these are to be stacked and conserved as future resources of Iron if it can’t be utilized in the present circumstances. Due to its friable nature, stacking of HSBD is a challenge and it is also compounding the problem by polluting the air under high velocity wind conditions. Because of its physical nature and occurrence in pockets pose challenge to systematic mining. The existing processing set up of the operating mines is designed to treat either Direct Shipping ore (DSO) or Run-of-Mine (ROM) have grade >60% Fe. The present practice of beneficiating iron ore fines (<1 mm) comprise combination of two or more processes such as desliming, hydraulic classification, magnetic separation and flotation apart from requirement of grinding depending on liberation characteristics. The HSBD which is predominantly occur as free granular particles, is significantly low in its alumina content. This gives us an opportunity to utilize them by exploring a suitable beneficiation process so that the concentrate produced can be used as a sweetener for alumina rich iron ore/concentrate. Thus, in the present study, an attempt has been made to adopt dry high intensity magnetic separation technique to explore the amenability of the high silica blue dust for beneficiation.

Jan 1, 2019

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By Ramazan Comakli, Cemal Balci, Nuh Bilgin, Hanifi Copur, Can Polat, Deniz Tumac

"Application of mechanical excavators for rock excavation in both civil construction and mining engineering fields has increased significantly in recent years. Prediction of the excavation performance of any mechanical excavators – tunnel boring machines, roadheaders, impact hammers, continuous miners and shearers for any geological formation is one of the main concerns in determining the economics of a mechanized mining and/or tunneling operation. A new portable linear rock cutting (PLCM) device was developed in the Mining Engineering Department of Istanbul Technical University and supported by The Scientific and Technological Research Council of Turkey (TUBITAK-112M859). The PLCM is used for cutting small core or block rock samples by a real-life mini disc cutter. The results from the PLCM are compared with the results obtained from the full scale rock cutting tests and theoretical model. It is found that there is reliable correlation between test results obtained from both cutting tests and theoretical model. 1. INTRODUCTION Mechanical excavators are currently the only alternatives to drill and blast due to higher production rate, increased safety, uniform muck size, less roof support, easier ventilation, continuous rather than cyclical operation, and possibilities for automatic control. The most of large civil tunneling and some mining projects are now carried out by mechanical excavators rather than drill and blast methods. Mechanical excavators can be categorized into two main groups: full-face and partial-face machines. Full-face machines such as tunnel boring machines excavate the face in one mode at the size of the cutterhead. Due to their cutting mode, the shape of the face profile by the full-face machines can only be circular. As for partial-face machines, the cutterhead is attached at the end of a boom. The face profile excavated by the partial-face machines can be from circular to horseshoe shape due to the cutting mode of the boom."

Jan 1, 2016

By J. D. Miller, C. L. Lin

"The use of 3D X-ray tomography analysis for plant-site characterization of coarse particles at a sampling rate of about 3 kg/min for particles ranging in size from 150 mm to 1 mm at a voxel resolution of about 150 µm is now possible. This is quite a significant advance in X-ray tomography technology and promises to be useful for plant-site coarse particle characterization—size, shape, composition, density, texture, grain exposure and mineral liberation—with a response time of minutes after receiving the sample. This paper discusses applications in the mineral industries, including the coal industry, aggregates industry, metal mining and the processing of industrial minerals.IntroductionPlant-site characterization of coarse particles at coal preparation plants, crushed stone/aggregate plants and mineral processing plants is needed to improve plant capacity, product quality and/or process efficiency. Not much online coarse particle characterization is being done at these plants. Only some limited information regarding particle size is obtained online from reflected light images using analyzers such as the OPSA, Split and WipFrag™ analyzers. Even the laboratory analysis of coarse particles has been difficult because of the large amount of sample required to ensure statistical significance of the results. During the past several decades, laboratory 3D characterization of particles from energy and mineral resources by X-ray tomography has been demonstrated and used to good advantage (Miller and Lin, 2004, 2009).Three-dimensional X-ray tomographic analysis has its origins in the medical services industry, where it is used to provide internal images of the human body. It has since been developed for nonmedical applications as well (Banholzer et al., 1987). Figure 1 shows a schematic diagram of the cone-beam geometry micro-CT system. In our case, X-rays from a microfocus X-ray generator are partially attenuated by the sample (a packed bed of particles) that is made to rotate in equal steps in a full circle about a single axis of the particle sample. At each rotational position, the surviving X-ray photons are detected by a planar two-dimensional array (image intensifier) large enough to contain the shadow of the specimen. These two-dimensional projection images are collected using conventional video technology. The video signal for each projection is then converted to a two-dimensional digital array by an image processing system. Finally, a threedimensional image is reconstructed from the collected set of projection images."

Jan 1, 2016

By C. H. Stephenson, Z. White

This paper presents the design approach case study for incorporating a Technogrid® conveyance End-of-wind arresting system within the new South32 Hermosa headframe. Focus is placed on energy absorption requirements, structural integration, and mounting details tailored to the geometry and operational constraints of the headframe. Key considerations include arresting forces, load path continuity, and connection design to ensure reliability and maintainability. The paper also discusses coordination with other headframe systems and the iterative design process used to meet safety standards and client objectives.

Feb 22, 2026

By A. Martikainen, H. Dougherty

"At the Kemi Mine, a recent expansion into the Surmaoja orebody required an increase in ventilation capacity. A new ventilation shaft was built with two main fans. The installation is near the entrance gate and only 1.7 kilometres from the nearest permanent dwelling. The main fans were first taken into use as exhaust fans in October 2014. Shortly after the fan installation, comments concerning fan noise were received from the neighbours. The first noise measurements were taken at the main fan installation site by Outokumpu personnel in March 2015. Due to higher than expected recorded values, during late June, 2015, a two-week environmental noise study was planned by the engineers and executed by a consultant specialized in noise measurement. The measurement results were analysed and compared to the requirements of the environmental permit and Outokumpu’s factory standards. While the measured values at the nearest dwelling were within the environmental permit limits, high noise values were recorded at the fan station. A second two-week study will be performed after construction of the main-fan heating station has been completed. Actions taken will depend on the outcome. INTRODUCTION The Kemi Mine is a part of the Outokumpu chain of integrated ferrochrome and stainless steel manufacturing in the Kemi-Tornio region in Finland. The mine itself is a large underground operation with a production capacity of 2.7 million tons of ore per annum. It is also the European Union’s only chrome mine, and at present (2015) the mine extracts 2.4 million tons of chrome ore per year. Safety, cost-effectiveness, and environmental friendliness are hallmarks of the Kemi Mine. Environmental impact produced by the operation of the mine is limited due to the insolubility of the oxide chromium ore, the gravity-based and chemical-free enriching process as well as the closed circulation system of the process water which serves both the whole mine and the enrichment process (Outokumpu, 2015). Importance of the environmental impact of the Kemi Mine is amplified by its closeness to the cities of Kemi and Keminmaa with the nearest habitants living less than 2 km away from the mine site. To show the cooperation with residents the Kemi mine organizes special “neighbour days” for the habitants of the areas closest to the mine. Also, information letters are sent to the neighbours, when changes that may affect the neighbours are being planned and executed."

Jan 1, 2016

By E. Bakhtavar

It is considered that the most economical method for the exploitation of Gol-e-Gohar Area 3 iron ore mine is to combine open-pit and underground methods. In this regard, the most critical problem is the determination of optimal final pit depth. In this paper, a method which was recently introduced on the basis of economical block models of open-pit and underground is used to determine optimal final open-pit depth of Gol-e-Gohar Area 3 mine with due regards to the future underground mining option. Considering a low cost and productive underground method as a feasible alternative for extraction of the lower part of this deposit, room and pillar was selected. It is concluded that after the assessment and comparison of different values for depth, optimal final open-pit depth was determined to be equal to 285 m.

Jan 1, 2010

By Matthew Wilcock, Kenichi Soga, Peter Wright

"This paper discusses how an existing grey cast iron segmental tunnel lining responds to construction of a new SCL tunnel transversely beneath with zero clearance; how the damage assessment for the existing tunnel was conducted for impact of longitudinal movement; how the tunnel is subsequently instrumented to observe both movement and stress manifestation at its longitudinal connections and how the results from the instruments compare with the prediction. An assessment of neutral axis of the tunnel in longitudinal flexure is also explored using interpolated horizontal displacement data from a conventional monitoring system. INTRODUCTION The Royal Mail Tunnel (RMT) (formely Post Office Tunnel or ‘Mailrail’) was constructed using semi-mechanised deep level construction techniques from 1914 and 1917 (Lee 1938). Commencing full commercial operation in 1926, the system was until 2003; conveying parcels the 6.5 miles between seven sorting offices in the center of London, and linking the system with main line rail stations, Paddington and Liverpool Street (The British Postal Museum & Archive 2013). A single tunnel of 2.74m internal diameter facilitated a bi-directional twin narrow-gauge (~611mm gauge) railway road system for electric driverless operation. The tunnel lining is segmental grey cast iron (grade 10) made up of six flanged segments and a smaller flanged key segment; constructed into a ring of width 508mm The external diameter of the tunnel is 2.971m. For further details of the tunnel lining and material properties are outlined by (Devriendt & Alhaddad 2014).London Underground Bond Street Station is a major station of the London Underground system in the very center of London; in its vicinity, the RMT runs west-east perpendicularly above the north south Jubilee Line tunnels. Historic survey record of the Jubilee Line’s (the then Fleet Line) construction in 1974 and its impact on the RMT case is documented in (Crossrail 1993): it is one of only a hand full of case-studies frequently cited when assessing the impact of new construction scenarios of this type; not least including the assessment of the same tunnel, at the same site some 40 years later, and the subject material for this paper: It noted significant vertical displacement of ~90mm to the RMT without noticeable serviceability or operational impediment."

Jan 1, 2016

By B. Akwasi Osei

The lack of metrics to assess clamshell formation dredgeability limits the ability of engineers to predict the dredgeability of compact material and increases the risks associated with clamshell selection. Research is needed to develop metrics for predicting clamshell dredgeability. The objective of this paper is to evaluate possible metrics to predict the dredgeability of compact aggregates by hydraulically actuated clamshell dredges. Data on cylinder pressures and displacements, motor current, bucket tilt and cycle time (CT) were collected from a dredge. Work done and motor energy, potential metrics, were computed and their suitability in predicting dredgeability evaluated. Data analysis shows that; there is no correlation between tilt angle and work done or motor energy; a low correlation between CT and work done, and a strong correlation between CT and motor energy. Work done is a better measure of formation dredgeability, than motor energy, as it shows lower variability. However, in difficult digging conditions, work done alone does not accurately predict dredgeability. This work shows that, it is feasible to use cylinder pressures and motor signals data to predict dredgeability.

Jan 1, 2010

By X. P. Zheng, H. K. Lin

Barium fluorophlogopites were synthesized in the laboratory to investigate the effects of composition and crystal parameters on surface properties and floatability. The negative surface charge of mica is determined by the barium content, the crystal cell volume, the distance between the layer structure and the Ba-O bond length. The higher the barium content, the larger the cell volume and distance between the layer structure, and the longer the Ba-0 bond, the more negatively charged the surface is, and, hence, the more easily adsorbed are cationic collectors. When an anionic collector (sodium oleate) is used, barium oleate forms on the mica surface and hence chemical adsorption occurs.

Jan 1, 1995

By Ronald J. Roman

As in every business venture, the primary objective of a mining operation is to make money for those who supply the venture capital. Therefore, all decisions concerning the operation of the mining operation should be made in light of the resulting effect on profit. The ultimate control is on profit, but the process is controlled, for example, by aiming for a recovery or concentrate grade knowing its effect on profit. The normal procedure used to determi.ne the profitability of a venture is to "present worth" all costs and incomes back to some arbitrary year zero. Every company has formed a management decision as to what it will require as a minimum return before it will undertake an investment. Once the economic analysis is completed, investment will be made only if the venture shows a positive present worth. If two alternatives are available, the alternative with the larger positive present worth is the one chosen. The same principles can be applied to the selection of a production schedule.

Jan 1, 1971

By T. Skodack

This presentation will compare actual work site results for the loading and transport of shot rock for two major tunneling projects in North America. "SCARMAR" (the Canadian subsidiary of S & M Construction) is operating a rail bound Hagglund continuous gathering arm loader in combination with a Hagglund nine car shuttletrain system at the West End of Table Mountain on the B.C. Railway project near Tumbler Ridge, Canada. Al Johnson Construction is operating a Hagglund rubber tired continuous gathering arm loader in combination with haul trucks at the Rocky Mountain Pump Storage Project near Rome, GA. This paper will compare: 1) tunnel and ground conditions, 2) the total work cycle as it relates to mucking and haulage 3) efficiencies and related problems with the two systems 4) mucking and haulage rates 5) operating costs, and 6) recommendations for future large tunnel excavations. Manuscript not received in time for publication.

Jan 1, 1983