Search Documents

Airy kind of a power system is a complicated network of various electrical components, such as cables, transformers, electric machines, circuit breakers, etc. For a system to work continuously and efficiently, each of the components has to be in perfect operating condition. The failure of any of these components can cause serious interruption of the supply and may in several cases involve a lot of precious time and labor in removing and replacing the damaged equipment it may also give rise to dangerous overvoltages on the system, thereby causing a safety hazard. Any piece of electrical equipment can have two likely modes of failure. The first would be the degradation of solid insulation material due to overheating, mechanical damage or a combination of the two, In this mode of failure it is possible that If the insulation damage is not an instantaneous phenomenon (a cable damaged by severe mechanical, Stress) that a detectable leakage current will do lop prior to the faint. The fault would probably he a result of heating and deterioration of the insulation by the leakage current.

Jan 1, 1975

By Forrest T. Moyer

[The safety record of the nonmetal mining industry during 1965 way worse than that of 1961 in all general measures s of injury experience except for a slight improvement in the number and frequency rate of nonfatal injuries Work fatalities in 1965 totaled al and occurred .it a frequencyrate of 0.29 and a severity rate of 1,711 per million man-hours of worktime. The fatality total was seven oven higher than to 1964 and the injury ratess increased d 32 and 28 present, respectively Thin total. of 2,172 nonmetal injuries u- in 1965 was 3.4 less than in 1964 and the frequency rate per million ion man-hours worked declined percent to 22.73 from: 23.14 in 1964. However, the 1965 nonfatal severity rate of 1,339 per million man-hours worked was 15 percent our the: d.96,1 rate of 1,160, This increases was largely attributable to two more permanent total and nine more permanent partial injuries. in 1965 than in the proceeding year. The average severity all injuries in 1965 was 132 days, 1-I. or charged per injury or 25 days more than in 1961. Injury experience in the nonmetal mining industry, including and excluding officeworkers, for the a-year period 1961-65 is shown in table 1. The average number of men working, on active days in 1963 was 48,429, or 635 fewer than in 1961. However, mines and mills, wore active an average: of 5 days more for a total of 277 in 1965, and each worker averaged 2,245 hours compared to 2', 190 hours in 1961. As a result, aggregate worktime of 108.7 million man-hours increased 1 percent over the 1964 total of 107.4 million hours.]

Jan 1, 1970

By H. B. Humphrey

WHEN THE BUREAU OF MINES was created in 1910, the organic act had as one of its main provisions the following: That it shall be the province of said bureau and its director, under the direction of the Secretary of the Interior, to make diligent investigation of the methods of mining, especially in relation to the safely of miners and the appliances best adapted to prevent accidents, the possible improvement of renditions under which mining operations are carried on, the treatment of ores and other mineral substances, the use of explosives and electricity, the prevention of accidents, and other inquiries and technologic investigations pertinent to said industries, and from tinge to time make such public reports of the work, investigations, and information obtained as the Secretary of said department may direct, with the recommendations of such bureau. The nationwide nature of the health and safety work of the Bureau of Mines has given its representatives an opportunity to study and report on matters pertaining to health and safety in mines and related operations from the time the Bureau was established to the present. Regular annual reports and numerous additional papers and reports have been published each year to place on record and to make available the information gathered. While the basic purpose of this bulletin is to describe health and safety reports for the period January 1947 through June 1955, a selected number of earlier publica¬tions that are believed pertinent for reference purposes are included.

Jan 1, 1956

By George A. Morgan

The production and processing of crude petroleum and natural gas are the dominant economic sectors of the Middle East. The IS countries that constitute the region accounted for 26% of world crude petroleum output, 17% of world natural gas plant liquid production, and almost S% of world dry natural gas production. About 66% of total world crude petroleum reserves and 31 % of total world natural gas reserves are in the Middle East. Transportation and port facilities in the region are geared to expediting efficient and rapid shipment of these materials. U.S.-dollar-denominated export sales of these fuels, estimated at $120 billion in 1989, provide funding for further diversification of the mineral industry. This is usually through development of downstream facilities for producing energy intensive metals such as aluminum and byproducts of the fuels such as petro-chemicals and fertilizers. Earnings from the industry are also channeled by sever-al Governments in the region to mineral industry projects in Africa and elsewhere. A fairly wide range of nonfuel minerals is produced in the region. However, the variety of minerals produced, output levels, and the size of the overall nonfuel mineral economy is dominated by Iran and Turkey. Turkey, with a diverse mineral production and strategically situated between Europe and the Middle East, ranked among the top three world producers of boron, chromite, pumice, and strontium. It was also a significant world producer of magnesium com-pounds, mercury, and sodium sulfate. Iran had generally lower output owing to 9 years of neglect to the mining sector between 1979 and 1988. It was a significant producer of gypsum and fifth in world production of strontium. Despite a very small domestic mineral industry, Israel was second in world production of bro-mine and a significant producer of phosphate rock and potash. Jordan ranked fifth in world production of phosphate rock. Iraq ranked about eighth in world production of sulfur, a commodity of major importance in the metallurgical, petrochemical, and fertilizer industries.

Jan 1, 1992

This appendix contains the list of equipment, their corresponding number and their specifications with the quotations from the vendors/ manufacturers who can supply this equipment. The listings are arranged by process plant areas.

Jan 1, 1979

By Krishna P. Sinha

An investigation was made to determine the creep behavior of oil shale at elevated temperatures. During the first phase of the investigation, work done on creep behavior of geologic materials was reviewed and triaxial creep tests on oil shale were planned. Tests at temperatures up to 250°C and axial stress up to 3000 psi were conducted at no confinement and at confining pressures equal to 1/3 and 2/3 of axial stress. Wide variations in the elastic properties as well as creep characteristics are exhibited. Creep deformation is more pronounced at elevated temperature but no definite quantitative remarks can be made regarding effect of grade of oil shale due to wide scatter and limited number of data paints. Primary creep can be described by a power law. Secondary creep seems to be an experimental function of deviatoric stress. Teritary creep was not observed within the test duration (24 hours in most tests).

Jan 1, 1983

By L. J. E. Hofer

"INTRODUCTION This paper is riot to be considered a complete survey of data on carbides; it is only an attempt to correlate the more reliable of the existing data of interest in connection with the Fischer-Tropsch synthesis, and its purpose is to guide future experiment and thought.A general review of the literature on the Fischer-Tropsch synthesis will be published in the near future as a chapter by H. H. Storch for a book entitled, ""The Chemical Utilization of Coal,"" edited by H. H. Lowry. This chapter covers the literature up to l9). It is planned to bring the review up to date in a comprehensive bulletin on Synthetic Liquid Fuel Processes to be completed during the next year. ACKNOWLEDGEMENTSThe author discussed the significance of the data with several members of the Physical Chemistry and Hydrogenation Section.THE PREPARATION OF CARBIDES OF IRON, COBALT, AND NICKELThe reaction of carbon monoxide with Fischer-Tropsch metals was first studied in a quanitaive way by Bahr and his coworkers. The contents of their first papers, 3/ 4/ 5/ which deal with the action of carbon monoxide on nickel, cobalt, and iron, will be described in the following paragraphs, together with the pertinent results of other investigators."

Jul 1, 1944

By W. A. Young

To initiate this project a critical evaluation of the pre-sent phosphate mining industry in the Western phosphate field was conducted. Mines were visited, mine operators were interviewed and pertinent literature studied. Three phosphate mining enterprises were reviewed and mining cost estimates prepared. The report discusses the present state of phosphate processing, rock alteration and location. New ideas and concepts are proposed to improve the recovery of phosphate rock from the Phosphoria formation. The report evaluates two variations to the present phosphate open pit mining methods, which were developed to improve the economics of mining phosphate and to better accomplish necessary reclamation and accelerate the time for environmental recovery. A material handling system using conveyor haulage will eliminate the need for trucks. Terrace haulback utilizes safety benches to haul and dispose of waste in the mined out pit. Ore will be removed from the pit via an inclined, cable-supported mobile conveyor.

Jan 1, 1980

By Henry R. Ensminger

Brazil's gross domestic product (GDP) grew only slightly in 1988 to $277 billion at current prices.2 The growth rate was the smallest registered since 1983, when the rate was minus 2.8%. The economy's performance was strongly influenced by a 2% to 3% decrease in industrial production and civil construction. The mineral industry, however, countered the downward trend in the industrial sector and grew a modest 1.4%. In November, Brazil adopted a new Constitution that placed significant restrictions on foreign investment in the mineral industries. Under certain provisions of the new Constitution, foreign companies were prohibited from establishing new mining ventures in Brazil as sole or majority owners. They could now enter the mineral industry only as minority shareholders with Brazilian partners. Foreign companies already established in Brazil had a 4-year grace period to find majority Brazilian partners, or to establish vertically integrated processing operations (mining, processing, smelting, and refining). The new Constitution also prohibited foreign risk contracts for petroleum exploration.

Jan 1, 1990

By David R. Peterson

This user's manual covers a set of 5 computer codes which were generated during development of a simulation of deep ocean mining operational economics. Table 1.1 provides a summary of these codes, and a more thorough description of each follows, In addition to the descriptions in this user's manual, internal documentation is provided throughout each code, except for the very simple ones, for ease of understanding or possible modification. The two major codes are MINER, which performs the deep ocean mining system operational simulation, and MSWEEP, which calculates the sweep and feed efficiencies for a set of collector paths generated by MINER. The standard operating procedure is to input the system and operating parameters to MINER, which computes a set of collector paths automatically and stores the information in the fife PATH.DAT. MSWEEP subsequently retrieves the collector path data in PATH.DAT, and uses it to calculate sweep and feed efficiency. Separating MINER and MSWEEP allows parmetric execution of MSWEEP without recomputing the collector paths with MINER. PIPEST, RESP, and OBSTCL are special-purpose codes described in more detail in the following documentation.

Jan 1, 1979

By Richard D. Miller

This Bureau of Mines publication contains analyses and related source data for 271 natural gas samples from 22 States collected during calendar year 1982. All samples were obtained and analyzed as part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by the mass spectrometer and chromatograph. The results of the investigation of the occurrences of helium are published annually to make the information available to the petroleum industry and the general public. Twenty-six publications have presented the results of 13,051 gas analyses vide prior to 1982. The first 3 bulletins (1-3)3 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960; these bulletins have been supplemented annually by information circulars (4-17, 19-24, 26) containing 7,833 analyses of samples collected since 1960.

Jan 1, 1983

Data recently released indicate substantial improvement in mineral industry performance for 1984. Business plans to increase plant and equipment spending in 1984 by 14.8 percent, according to a recent survey conducted by the Commerce Department's Bureau of Economic Analysis (table 1). In contrast, capital spending by all industries declined 4.8 percent in 1983 and 2.3 percent in 1982. The latest estimate of planned expenditures for 1984 is $2.2 billion higher than the comparable estimate based on the survey conducted in late January and February 1984.1/ [ ] Of particular significance to the U.S. mineral industries are the 15.5-percent increase in capital spending planned by manufacturing in 1984 and the planned 18.6-percent increase in spending by durable goods manufacturing, where the largest increases are planned in the transportation equipment (26.4 percent) and electrical machinery sectors (23.5 percent). Capital expenditures in manufacturing declined in both 1982 and 1983.

Jan 1, 1984

By John A. Davis, David W. Brunton

During the past few years great progress has been made in the United States toward safer, more efficient, and more economical tunneling methods. This advance is partly due, no doubt, to the recent increase in the number of tunnels and adits driven for devel- oping and draining mines and transporting ore. The Bureau of Mines during 1911 and 1912 made a special examination of this phase of mining operations, in connection with an investigation of mining methods and means for preventing accidents. The details especially studied were the provisions for the safety of employees, the kinds of equipment, the methods of driving, and the costs of con- struction. The results and conclusions obtained from that investi- gation are discussed and summarized in this bulletin. Up-to-date information concerning tunneling methods is difficult to obtain. There are few books on the subject; and much of the material they contain, although interesting and of value historically, is now obsolete. The engineering periodicals, it is true, endeavor to keep abreast of the times, and several in nearly every issue present some article bearing upon tunnel work. But the very multiplicity of these articles prevents one from reading them all, and the foreman or superintendent in charge of a tunnel, or the mining engineer designing one, and especially the business man financing the project, has no time for a lengthy search after scattered articles in order to determine the present status of tunnel work. Then, too, knowledge of new methods travels slowly. Valuable inventions and improve- ments in tunneling as well as in all the other industries frequently remain in the notebook of the investigator, or as theses are buried in university libraries, or are published only in journals of small scien- tific societies. New tunneling methods and equipment that are prov- ing safe, efficient, and economical may be totally unknown outside the district in which they originate. This paper, based on a special examination both in the field and in engineering literature, is in- tended to supply data concerning modern and recent tunneling practice in the United States, and to make suggestions that, it is hoped, will result in a saving to the mining industry of energy, capital, and life.

Jan 1, 1916

By J. L. Konchesky

The technical feasibility of gasifying powdered, noncoking, low-rank coal with steam in an externally heated tube has been demonstrated. The tube, 112 ft. of alloy-steel tubing shaped into a helix, served as an electrical conductor of electricity used for heating. The effects of the following variables were studied: Residence time of coal in reactor, average reaction temperature, steam concentration, and rank or geologic age of coal. Reaction pressure was maintained in the range 19-26 p.s.i.a. High carbon conversions and large yields of synthesis gas were obtained with low-rank coal. In one test, for example, about 88 pct. of the carbon in a subbituminous C coal was gasified at 1,910* F. with a residence time of 1 sec. The gas contained 58 pct. H2, 19 COD 15 CO, and 3 CH4; the yield was 30 cu. ft. (at 32' F. and 14.7 p.s.i.) of synthesis gas (CO + H2) per pound of dry coal.

Jan 1, 1960

By G. H. Gronhovd

This is the final report on a research program to develop a pilot plant gasifier for slagging gasification of lignite at high pressures and to obtain process data under various operating conditions. An operable pilot plant was developed, and the test results show that lignite is well suited for the process. Tests were run at pressures from 80 to 400 psig, and the results indicated that pressure had little effect on gas composition or the material requirements per unit gas produced. Gas production rates as high as 26,000 scfh/sq ft of reactor area were obtained at 300 psig, but limitations on auxiliary equipment prevented full-capacity operation at 400 prig. In several tests lignite having a 37-percent moisture content and 2,500° F ash-fusion temperature was successfully gasified. Refractory materials were found to have a short life in contact with high-temperature slag, and a water-cooled taphole was developed. Exploratory tests with coking coal were unsuccessful.

Jan 1, 1970

By Robert A. McColly

This Bureau of Mines report compares the availability of federally owned minerals in Arizona with lands considered favorable for discovery of mineral resources, to deter-mine the extent to which Federal mineral lands in such areas have been withdrawn by legal action or restricted by management practice. Of particular concern are restraints on Federal lands in areas identified as highly favorable for occurrences of valuable mineral deposits. Excluding Indian lands held in trust by the Federal Government, about 32 million acres, 44%, of Arizona's mineral estate is federally owned. This total includes lands with partial Federal mineral ownership. Approximately 16.5 million acres, or 52% of these lands, are available for location or lease. This includes 496,000 acres, 62%, of the lands highly favorable, and 2.6 million acres, 57%, of the lands moderately favorable for locatable minerals in Arizona. All other Federal mineral lands are either withdrawn or restricted, reflecting a wide range of purpose, authority, and impacts on mineral exploration and development.

Jan 1, 1987

By N. E. Hanna

To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain safety tests prescribed by the Federal Bureau of Mines. These tests are described in Schedule 1-G4/ (explosives) and Schedule 26A5/ (blasting devices). An explosive or blasting device that passes the appropriate tests is placed on the active permissible list. As this list is subject to continuous revision, it has been the practice of the Bureau of Mines to publish periodically the names of explosives and blasting devices that have been added to the active list, as well as those that have been transferred to the inactive list; changes in brand names also are reported. The present circular gives all explosives and blasting devices on the active permissible list as of December 31, 1957, and shows all changes, additions, and transfers in that list between December 31, 1951,6/ and December 31, 1957.

Jan 1, 1958

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

By J. Drew Potts

In this U.S. Bureau of Mines study, four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner sections averaged 0.59 and 0.26 mg/m3, respectively. The stageloader-crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feeder-breaker contributed 0 to 0.2 mg/m3 of dust. A 1,000-ft increase in belt entry length or a 200-to 500-st-per-shift increase in production resulted in roughly a 0.1-mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 2010

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984