Search Documents

By B. Stimpson, K. Kosar, K. Barron

"A number of high wall failures have occurred in some of the Alberta coal strip mines of a type called by the authors ""Multiple block plane shear slope failure "". They cause rapid deterioration of the dragline bench, reduced productivity and maintenance costs.The failures are invariably associated with the presence of almost horizontal (± 5 degrees) bentonitic clay bands in the overburden, often immediately above the coal seam, and regress behind the slope as a series of tension cracks which isolate detached blocks. As many as 17 sets of cracks have been observed, at lateral distances in excess of five times the slope height from the toe.The theory of this mode of failure is presented and a limiting equilibrium computer program which will produce deterministic or probabilistic (Monte Carlo) solutions is briefly described. A case history of one such failure is documented. It is shown that the extent of the regressive failure is exceedingly sensitive to the water table elevation, leading to the conclusion that drainage, if practical, represents the best control strategy. IntroductionA number of high wall slope failures are occurring in some of the coal strip mines in Alberta of a type called by the authors ""Multiple block plane shear slope failure""(I). These failures cause a rapid deterioration of the bench from which the dragline operates, reduced productivity, and necessitate conregresses into the slope as a series of tension cracks and detached blocks. As many as 17 prominent cracks or crack zones have been observed, the last being in excess of five times the slope height distant from the toe.The block between each pair of cracks must be at limiting equilibrium, i.e. the factor of safety equals one. This condition can be used to determine the locations of the cracks which develop in sequence behind the face."

Jan 1, 1986

By K. Galovich, P. Krivokuca

"Quinsam coal mine is located about 25 km west of Campbell River on the east coast of Vancouver Island, British Columbia. Using continuous miners in a fully mechanized retreat room-and-pillar operation, it produces low sulphur, “super compliance” thermal coal for domestic and international markets at a rate of about 2600 t/d. Currently, 65 people work at the site, including some corporate employees.Opened in 1993, the Quinsam mine had a dismal safety record until 1997. Lost time injuries and medical aids were unacceptably high. In 1998, a change in corporate structure brought a change in safety attitudes; a total and unequivocal commitment to safety as job No.1 by corporate and site management. This commitment was clearly spelled out in a new mission statement, circulated to all employees by the new President and CEO, David Slater: “Safety is job No. 1; Production flows from safety; and Think safety at all times.” As well as re-defining workplace safety practices, QCC tightened engineering controls and enforced strict adherence to mine plans.This paper provides a general background to the mining operation, and describes the safety practices that have resulted in an enviable safety record in recent years, reflected by provincial and national recognition."

Jan 1, 2004

"Mineral separation by exploiting the differences in mineral or metal specific gravities (sg) has been used since antiquity. In the modern era, this is most commonly seen in the recovery of gold by the use of centrifugal concentrators and the separation of coal (low sg) from waste rock (high sg) using heavy media cyclones and jigs. Other metals, notably oxides of tin and tungsten, are successfully recovered using some combination of jigs, spirals and shaking tables. However, many conventional gravity separation systems are limited to fairly coarse (>1 mm) to medium (>100 micron) particle separations due to the limitations of the gravitational separation forces in conventional equipment.Many of the high specific gravity minerals of interest are friable (e.g. cassiterite, wolframite, etc.) and excessive fines are generated in the grinding/comminution circuits which cannot be recovered with conventional equipment and may be lost directly to the tailings stream. Recent developments in centrifugal gravity separation equipment specifically designed for fine or ultra-fine particle separation and recovery have resulted in heavy mineral particle recoveries as fine as 10-20 microns. Ongoing research work has also identified the benefit of closed-circuit, multi-stage gravity recovery circuits using some combination of centrifugal concentrators and conventional equipment (tables, spirals, flotation, etc.) which can substantially increase overall plant recovery and final concentrate grade.This paper will provide details of the evolution of non-fluidized bed gravity concentrators for high sg mineral recoveries, correlate laboratory scale development work with plant results to confirm scale-up, and show how recent flowsheet developments have contributed to significantly improved plant performance.IntroductionGravity concentration is one of the oldest and most cost effective metal and/or mineral recovery systems, ranging from the classic hand panning of alluvial gold, through to the large scale production of a wide range of metals and minerals, including gold, silver, PGMs, black sands, coal and iron oxides. Conventional gravity recovery systems, comprised of some combination of sluices, spirals, jigs and shaking tables have limited application in fine particle (i.e. <100 microns) recovery, or where there are limited differences in particle specific gravities (sg), e.g. the separation of high sg, high value metal oxides (e.g. those of tin, tantalum or tungsten), from medium sg, lower value metal sulfides such as pyrite and pyrrhotite. These unit operations tend to have limited capacity, and while double and triple turn spirals and multi-deck tables have been developed, extensive floor space is often required in order to process the tonnages incorporated in the modern mineral processing plant."

Jan 1, 2017

By D. W. McDonald, L. M. Heaman, R. A. Creaser, T. Davies, T. Chacko, A. Simonetti

"The Three Bluffs gold deposit is located in the Committee Bay greenstone belt, which forms part of the Rae domain of the western Churchill province, Nunavut, Canada. Gold mineralization is hosted by iron formation of the Neoarchean volcanosedimentary Prince Albert Group, and is associated with silicification (quartz veining) and sulfidation of magnetite and other Fe-rich minerals. Conventional U-Pb zircon dating of a conformable dacite unit within the volcanosedimentary host-rock sequence and a crosscutting diorite intrusion confirm a ~2.7 Ga age for deposition of the supracrustal package. U-Pb monazite dates and Pb isotopic analyses of sulfides were obtained by laser ablation-multicollector-inductively coupled plasma-mass spectrometry (LA-MC-ICP-MS). A subset of U-Pb monazite (1813.8 ± 8.7 Ma) and Re-Os arsenopyrite (1822 ± 21 Ma) dates, combined with a Pb-Pb secondary errorchron age for pyrite and arsenopyrite (1829 ± 77 Ma), suggest that gold mineralization associated with sulfidation of the iron formation occurred at ~1815 Ma, prior to high-grade (upper amphibolite facies) tectonometamorphism in the Three Bluffs area (D2TB/(M2TB). An ~1815 Ma age for deposit formation is broadly consistent with evidence from elsewhere in the western Churchill province and to the southwest in Manitoba and Saskatchewan for a late Trans-Hudson (1.9-1.8 Ga) gold mineralizing event. The majority of U-Pb monazite ages form a second population at 1780.6 ± 4.2 Ma, similar to the age of the majority of Re-Os arsenopyrite analyses (1763 ± 11 Ma). These dates are thought to reflect the timing of peak M2TB metamorphism. 40Ar/39Ar dating of amphibole, biotite, and muscovite yielded plateau ages ranging from 1723.8 ± 9.0 Ma to 1710 ± 17 Ma, which are interpreted to record the timing of postpeak metamorphic cooling to below the respective closure temperatures for Ar diffusion in these minerals. Le gîte aurifère de Three Bluffs est situé dans la ceinture de roches vertes de Committee Bay, laquelle appartient au domaine de Rae dans l’ouest de la province de Churchill, au Nunavut, Canada. La minéralisation aurifère est encaissée par des formations de fer d’âge Néoarchéen appartenant aux roches volcanosédimentaire du Groupe de Prince Albert; la minéralisation est associée à de la silicification (veines de quartz) ainsi qu’à la sulfidation de la magnétite et d’autre minéraux riches en Fe.Les résultats de la géochronologie U-Pb conventionnelle sur une unité de dacite concordante au sein de la séquence volcanosédimentaire ainsi que d’une intrusion de diorite qui les recoupe indiquent que ces roches supracrustales ont un âge de ~2.7 Ga. Les âges U-Pb de la monazite ainsi que les analyses des isotopes du plomb des sulfures ont été obtenus par ablation laser (LA-MC-ICP-MS). Certains des âges U-Pb obtenus à partir de la monazite (1813.8 ± 8.7 Ma) et des âges Re-Os retournés par l’arsénopyrite (1822 ± 21 Ma), en association avec l’âge indiqué par une isochrone à données dispersées « errochron » secondaire Pb-Pb pour la pyrite et l’arsénopyrite (1829 ± 77 Ma), suggèrent que la minéralisation aurifère associée à la sulfidation de la formation de fer s’est formée vers ~1815 Ma, avant que l’événement tectonométamorphique (D2TB/(M2TB) de niveau élevé (faciès des amphibolites supérieures) affecte le secteur de Three Bluffs. Un âge de mise en place de ~1815 Ma pour ce gîte est compatible avec les données en provenance de l’ouest de la province de Churchill ainsi que plus au sud-ouest au Manitoba et en Saskatchewan qui indiquent la mise en place de minéralisations aurifères à la fin de l’orogénèse Trans-Hudsonienne (1.9-1.8 Ga).La majorité des âges U-Pb de la monazite constituent une seconde population formée à 1780.6 ± 4.2 Ma, ce qui est similaireLà l’âge obtenu pour la plupart des analyses Re-Os sur l’arsénopyrite (1763 ± 11 Ma). Ces âges reflètent probablement l’atteinte du pic métamorphique M2TB.La géochronologie 40Ar/39Ar de l’amphibole, de la bio"

Jan 1, 2009

Strategic Branding ? In 2006 Explore for More was created ? By industry, for industry ? Cohesive approach to career attraction ? Defines industry and employers of choice Career Kits ? Positive impression of mining: ? before seeing the brochure 31% ? after seeing the brochure 83% ? Likely to consider a career in mining: ? before seeing the brochure 12% ? after seeing the brochure 23% MARS ? Mining Attraction, Recruitment, and Retention Strategy (2007-2010) ? Attract, recruit and retain a skilled workforce ? Increase participation of under-represented groups ? Dispel myths and misconceptions of the mining industry ? Inform and educate Canadians of career opportunities ? Promote and build upon industry best practices in workforce planning

May 1, 2009

By K. E. Barnes

"The “Jameson Cell” flotation cell was developed at Mount Isa Mines in the late 1980’s to address deficiencies in our flotation column installations. Early base metal installations had a variable record. The test work and trials showed they made an improvement metallurgically when operated correctly, but performance of the early installations was hindered by a range of operational and maintenance issues. The installations needed to be more robust, and we needed a better understanding of how to successfully integrate the cells into the plant flow sheet.During the 1990’s, Jameson Cells had great success in coal fines flotation and organic removal in SXEW applications, and became the standard in these applications in Australia. These installations improved the cell design and materials of construction and the cell flow sheet design, to make it low wear with self-regulating control, producing good performance with little operator input.These improvements have enabled a fresh look at the use of Jameson Cells in base metals. Recent new installations have shown significant benefits in “hybrid” circuits, that combine the best features of both Jameson Cells and conventional flotation cells, achieving better overall circuit performance in a smaller footprint than either technology could do by itself.Case studies of successful base metal applications are discussed, using size-by-size mineralogical performance to explain the improved circuit performance. The new methods of flow sheet test work design are also described."

Jan 1, 2006

By D. Bois, P. Poirier, B. Bussière

Environmental desulphurization is an attractive alternative for the management of acid generating tailings. Bulk sulphide flotation is the most commonly used method to produce desulphurized tailings, as shown from many previous works. This process can reduce the volume of problematic tailings to manage by making a sulphide fraction concentrate. The desulphurized tailings can then be used as construction material for an engineered cover to prevent acid mine drainage. In this paper, the results from different laboratory and pilot scale flotation tests are presented. These results confirm that low sulphide non-acid generating tailings can be produced by froth flotation. It is also demonstrated that sulphide concentrates obtained from desulphurization mixed with the appropriate binders can be used as feed material for paste backfill. From previous work on the evaluation of operating and capital costs of the desulphurization process for different ore types, the use of desulphurization as a tailings management approach was studied for several scenarios. The desulphurization process was then compared with other technologies (underwater disposal, engineered soil cover) currently used to prevent acidic drainage (AD) for a new mining operation. Results show that partial or total desulphurization are technically and economically viable options to manage tailings during mine operation. Mine waste managers should consider desulphurization as an efficient technology.

Jan 1, 2005

By M. Courchesne, C. Barbery, D. Hodouin, C. Carrier

"The carbon-in-pulp process for recovery of gold dissolved in dilute cyanide solutions, in the presence of solids, has now replaced the convedntional processes of pregnant liquid/barren solids separation followed by Merrill-Crowe precipitation. Most plants built over the past ten years incorporate a CIP section. The process is described as cheaper in capital and operating costs, and few major start-up or operational difficulties are reported. For the purpose of the present paper, the CIP process will be assumed to consist of the following sequence of operations (Figure 1):- the slurry stream coming out of the cyanidation circuit is first screened to remove any tramp oversize material. Gold dissolution is assumed to be complete before entering the CIP circuit.- the slurry is sent into a series of agitated tanks in which it is mixed with activated carbon. The carbon particles size is much coarser than the top size of the ground ore. The tanks are fitted with screens that allows the slurry to overflow continuously into the next tank, while retaining the carbon in the tank. Slurry dilution is adjusted to prevent carbon from settling in the tanks. Agitation intensity is kept low in order to minimize carbon abrasion.- carbon is transfered from tank to tank in a discontinuous manner. According to a specific schedule, the carbon from tank one is removed, then carbon from tank two is sent to tank one, and so on, till the last tank, which is filled with regenerated carbon corning from the elutionregeneration section. The amount of carbon removed, the transfer from tank to tank, the sequence of transfer, the carbon inventory in the various tanks are parameters which are, up to a point, at th2 discretion of the operators, as long as they remove, batch wise, an amount of loaded carbon containing a similar quantity of gold to the one that has entered the circuit since the last transfer."

Jan 1, 1987

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

By J. R. Porter, C. Panaou

"A significant effort is expended on preparation of the capital estimate for feasibility studies. The development of the operating cost estimate is usually allocated a significantly smaller budget and less emphasis is placed on ensuring the accuracy of the operating cost. This paper presents a comparison of capital and operating costs of hydrometallurgy processing plants in order to demonstrate the importance that variations in operating costs have on the overall life-of-mine costs. The analysis is supported by a case study on the operating costs of a water treatment plant at an existing Australian hydrometallurgy facility at the feasibility design level. INTRODUCTIONDetermination of the economic validity of a minerals processing project is a critical outcome of a feasibility study. In many cases, the financial results of the feasibility study will determine if the project should proceed to execution. Ensuring that these results are reliable and built upon sound engineering practices allows companies to make informed decisions on resource opportunities and the selected technology.The methodology for developing a capital cost estimate at the feasibility level is well established. Specialist engineering estimators use budget quotations, first principle estimation and rules-of-thumb to develop an estimate with an accuracy of typically -10% to +15%. Cost reporting software packages are used to methodically build up the estimate from design information supplied by the engineering disciplines. Risk analysis and capital expense workshops are carried out to identify potential deficiencies in the estimate. It is widely recognized that in order to successfully produce a feasibility level capital estimate with an appropriate level of accuracy, a rigorous development process is necessary.The development of the operating cost estimate is typically less rigorous than the capital cost estimate. The operating cost is normally derived by the process engineering discipline and rarely are specialist estimators used to support the development. The allocated budget for producing an operating cost is usually smaller and less emphasis is placed on ensuring the accuracy and contingency reflect the most likely operating cost scenario."

Jan 1, 2012

By O. J. C. Runnalls

"Canada became the world&apos;s largest uranium producer in 1984. That leadership position is likely to be maintained for many years into the future because of a firm production base, many undeveloped known deposits with commercial promise, and a large geologicalpotential for new discoveries.There are some uncertainties on the horizon, principally because of restrictive actions in process within the U.S.A., which are aimed at preserving a deteriorating domestic uranium industry. Should such actions result in import restrictions, for example, there would be a negative effect on foreign producers at least in the short term. Canada may avoid such difficulties under a tentative U.S.-Canada free-trade agreement where restrictions on the import of Canadian uranium into the United States would be eliminated. Over the longer term, demand for Canada&apos;s uranium resources will grow because of the foreseen growth in the world&apos;s installed nuclear power capacity. IntroductionSince the phenomenon of nuclear fission was discovered in 1938, the utilization of uranium has grown substantially. Initially, the principal use for uranium was in the production of nuclear weapons. However, once civilian nuclear power reactors began to be built in the 1950s, an increasing fraction of uranium output was directed to the production of fuel elements for use in electricity generating stations.The cumulative uranium production by those countries in the World Outside Centrally-Planned-Economies Areas, WOCA, during the period 1938 to 1985 exceeded 800 000 tonnes of uranium. Some 60% of that was mined in the United States and Canada, as indicated in Figure 1. In 1986, nearly 80% of WOCA output came from five countries, Canada, United States, South Africa, Australia, and Namibia, as indicated in Table 1 and illustrated in Figure 2.During the past decade the world annual consumption of nuclear energy has more than tripled (Fig. 3). As of December 31, 1986, the world total of nuclear power reactors had reached 394 with a total net capacity of 270 GWe. The thermal output from nuclear power plants in 1985 exceeded 60% of the energy contained in all of the oil produced that year in the Middle East. Thus, nuclear power has already become an important component in the world energy supply picture."

Jan 1, 1988

By C. Guo

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd oil sands plant. Over the past years (since 1997), there has been a marked change in the consolidation behaviour of MFT in the MLSB, which is attributed to microbial activity. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. In certain regions within the MLSB, gas bubbles are released to the water surface of the tailings pond. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings). This phenomenon contradicts the consolidation models for MFT developed over the past 20 years. The above phenomenon has also been reported at the oil sands tailings ponds operated by Suncor Energy Ltd. in Fort McMurray. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. The rapid densification of the MFT may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program is underway to study the mechanism leading to the rapid densification phenomenon. Systematic field investigations were performed to determine the distribution and characteristics of the rapidly densified MFT. Gas bubble distribution on the water surface was mapped to determine the zones of different biological activities in the pond. These field investigations provided solid ground for further experimental and theoretical research. A number of small-scale column tests were carried out to observe the gas evolution and to measure the changes of some geotechnical parameters under different microbial activity. Also, a series of gassy MFT densification tests are being conducted to study the mechanism of the rapid densification of the MFT under microbiological activity. A review and discussion of the research program is given and some preliminary research results are presented in the paper.

Apr 1, 2005

By L. C. St. Arnaud

"Open pit mines can produce large disturbances within regional hydrogeologic systems. The degree of disturbance and the consequences on the local environment depend on the size of the pit and on the physical setting of the mine. Comparisons and contrasts are presented for three Noranda base metal open pit mine sites.The Brunswick Mining and Smelting No 6 open pit has a surface area of 11 ha and a depth of 185 m. It is located within complexly deformed schists and meta-volcanic rocks. The massive sulphide and iron formations visible along the north and southwest walls of the pit generate acid drainage. Mining ceased in 1983, and the pit is presently being filled with waste rock and neutralized drainage water. Water balance calculations estimated a total fill up time of sixteen years. As the water level rises, leakage to groundwater could take place across a fault zone intersecting the pit.The Mattabi Mines F-Group pit has a surface area of approximately 3 ha and a depth of 50 m and is also set in meta-volcanic rocks and acid generating iron formations. Production at this site ceased in 1982, and the low pH pit water is neutralized and pumped into a nearby lake at least every five years. Major water inflows are from precipitation and groundwater. Groundwater mounds within adjacent high land surrounding the pit provide a natural hydraulic barrier to groundwater flow, except for the southeast side. As a consequence, the pit water elevation is being kept below the elevation of the nearby creek in which some of the pit water could drain.The Bell Copper open pit covers an area of 40 ha and is 270 m deep. With present ore reserves, the mine might be in operation until 1992. The geology around the pit consists of andesitic tufts, siltstones and shales, and the acid generation potential of the rock is relatively low. A recent hydrogeological study estimated fill up time by precipitation and groundwater to be in the order of 260 years.With increasingly more stringent requirements for mine closure, it is anticipated that more detailed hydrological and hydrogeological studies of open pits will be required to determine post-closure environmental impacts and the suitability of open pits for mine waste disposal."

Jan 1, 1990

By W. R. Leeder

"The Quintette coal property lies in the Rocky Mountain foothills of northeastern British Columbia (see Figure 1). Quintette and the adjacent Bullmoose property of Teck Corporation are soon to become the first commercial coal mines in the Peace River Coal Field, which is estir1ated to contain 10 billion tonnes of metallurgical coal reserves.Denison Mines Limited acquired the original Quintette coal licenses in 1969 and 1970. Exploration began soon after and the first feasibility study was conducted in 1975. Denison devoted the following six years to extensive planning and feasibility studies of the project. During this period, the provincial and federal governments also undertook studies to assess infrastructure requirements and economic viability of development in this part of the province. Many of the proposed mine sites such as Bullmoose and Quintette were at least 100 to 150 kilometres from the towns of Chetwynd and Dawson Creek, the nearest centres serviced by good highways and a railroad, and a complete network of services would have to be provided if such mines were to be developed. The overall project became known as the North East Coal Development.Concurrently with the feasibility studies, numerous technical and sales missions to Japan were made by representatives of Canadian industry and government, culminating in January 1981 with agreements for Quintette Coal Limited and Teck Corporation to supply a total of 115 million tonnes 8 million tonnes per year for 15 years of primarily metallurgical coal to the Japanese Steel Industry."

Jan 1, 1983

By D Reddy Chinnasane

Outline Location of BirchtreeMine and Layout of 124 OB Cut and Fill Mining Background Purpose of the Studies Methodology Results and Analysis Conclusions and Recommendations

Oct 1, 2010

By M. Tarvainen, J. Kallioinen

"Depressed metal prices coupled with increasing production costs have presented a great challenge for operators to control and reduce the costs of production to maintain profitability. Depleting ore reserves, added to the above has forced Outokumpu to take a hard look at its operations, to develop new methods to profitably extend the life of its mines. One of the areas investigated and approved for further development has been the use of larger and more energy efficient equipment. As a result, large flotation machines were developed and today 38 and 60m3 flotation machines are in use.Secondly, ore preconcentration has been developed to avoid processing the part of the ore that has little or no mineral values.Another quite recent development and the topic of this paper, has been the use of coarse flotation before conventional flotation. The main idea is that part of the valuable mineral is separated as early as practical by floating it with specially designed flotation equipment, installed in the grinding classification circuit. The new flotation cell is specially designed for this application and differs from the conventional cells in the tank design, feed arrangement and modified mechanisms in some cases."

Jan 1, 1984

By Robert J. Maron, Mark Fernald, Alex Van der Spek, O’Keefe. Christian, Tim Bailey

"Sonar array-based non-invasive flow measurement technology is becoming an accepted and many times a preferred method of measuring challenging single and multi-phase flows in the mineral processing industry. This fundamental sensor and measurement technology has been extended to two developments that provide new measurement capabilities useful for monitoring and managing slurry flows and pipes.The first development is the non-invasive measurement of real-time velocity profile of slurry flow in horizontal pipes. Multiple non-invasive passive sensors measure localized velocities and are combined to provide a velocity profile measurement. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities and/or higher solids concentration while avoiding solids deposition or plugging and its associated operational costs.The second development is the non-invasive measurement of pipe wear on slurry lines. Presently, such measurements are made by hand-held portable ultrasonic thickness gages. The numerous shortfalls associated with the manual method are overcome with a set of permanently or semi-permanently installed transducers clamped onto the outside of the pipe. This ring of sensors contains a series of conformable ultrasonic transducers spaced around the circumference, which are used to measure the thickness of the pipe under their respective locations. Compared to manual methods, this system and approach results in better repeatability and accuracy. It also decreases inspection labor costs and pipe access requirements. The minimal accuracy variations in the presence of varying environmental temperatures will be shown. Trending of pipe wall thicknesses in high wear pipelines will be illustrated. The benefits of significantly improved pipe wear monitoring in hydrotransport lines with abrasive solids, and associated improvement in the ability to insure safe operation and avoidance of costly environmental damage due to leaks caused by pipe wear will be discussed."

Jan 1, 2009

By A. J. Hynes, Lutes. G. G., Ravenelle. J. -F.

"The Anomaly A area of the Clarence Stream gold deposits in southwestern New Brunswick contains mineralized structures that bear geometrical relationships to regional folding events. The four mineralized zones of Anomaly A (AD, MW, 93, and Murphy) are hosted by turbiditic graywacke, quartzose wacke, siltstone, and argillite sequences of the Kendall Mountain Formation. A regional scale structural analysis reflects at least four deformational events, three of which appear to control the folded geometry of Anomaly A (D2, D3, and D4). F2 and F3 folds are coaxial and are refolded into a dome and basin geometry by F4 folds. The mineralized zones are subparallel to axial surfaces of F2 folds. Structural analysis of a mineralized zone exposed at surface indicates that gold mineralization is hosted by a quartz-vein system that comprises veins generated during both D2 and D3. Threedimensional representations of Anomaly A created using drill-core data and ®GoCAD suggest that the quartz-vein system was emplaced in fault structures during D2 as well as within brecciated dilation zones during D3. Three of the four zones that make up Anomaly A have F2 hinge surfaces that can be linked through a geometry compatible with the style of F3 and F4 folds. The apparent continuity of these three zones indicates the potential for kilometer-scale mineralized structures at Anomaly A. Le secteur de l’Anomalie A du gisement aurifère Clarence Stream contient des zones minéralisées qui montrent des relations géométriques avec les épisodes de déformation régionale. Les quatre zones minéralisées de l’Anomalie A (AD, MW, 93, Murphy) sont comprises dans une séquence turbiditique composée de grauwacke, de wacke quartzitique, de siltstone, et d’argilite appartenant à la Formation de Kendall Mountain. Des quatre épisodes de déformation étudiés par l’entremise de cartographie structurale, trois semblent contrôler la géométrie de l’Anomalie A (D2, D3, et D4). Les plis P2 et P3 sont coaxiaux et sont replissés en dômes et bassins par les plis P4. Les zones minéralisées sont subparallèles aux plans axiaux des plis P2. Une analyse structurale effectuée sur une zone minéralisée exposée à la surface indique que la minéralisation aurifère est localisée dans un système de veines de quartz qui contient des veines générées durant D2 et D3. Des représentations en trois-dimensions créées avec le programme informatique ®GoCAD à partir de données de forages suggèrent que le système de veines est localisé dans des zones de failles D2 ainsi que dans des zones de dilatation associées avec D3. Trois des quatre zones qui forment l’Anomalie A possèdent des plans axiaux P2 qui peuvent être liés par l’entremise d’une géométrie qui respecte le style des plis P3 et P4. La continuité apparente de ces trois zones indique qu’une structure minéralisée pourrait s’étendre sur plusieurs kilomètres dans le secteur de l’Anomalie A."

Jan 1, 2008

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019