Search Documents

By John E. Kelley

A method for measuring the spark-shower radiance of metals when abraded on a grinding wheel was developed by the Bureau of Mines for evaluating the sparking tendency of metals. The radiance was measured in units of emissive power per solid angle per area of the detector. Over 100 metals were tested and rated relative to commercially pure iron. The metals tested included elemental metals, iron binary and ternary alloys, iron-carbon ternary alloys, commercial steels, nonferrous alloys, and a few hard-metal compounds. Some alloys were synthesized; others were obtained commercially. Alloys that possessed good strength properties were emphasized for selection. The results indicate that the spark-shower radiance of plain carbon steels and carbon alloy steels was greater than that of pure iron. Certain elements, particularly vanadium and chromium, reduced the sparking tendency of iron. Stainless steels and particularly nickel alloys displayed low spark-shower radiance. Some metallic elements had much lower radiance than iron; others, much greater. Plain carbon steels, heat treated to a variety of hardnesses, gave radiance values that generally increased with increasing hardness. The effect on sparking tendency of an increase in hardness of an alloy steel was studied. The sparking tendency increased with an increase in hardness to a maximum, then decreased with a further increase in hardness.

Jan 1, 1974

By Rudy J. Matetic

The National Institute for Occupational Safety and Health (NIOSH) at the Pittsburgh Research Laboratory (PRL) is conducting research to reduce the noise exposures of roof bolting machine operators and to prevent additional cases of Noise Induced Hearing Loss (NIHL) thru the development of engineering noise controls. This paper describes and evaluates an engineering noise control for the roof bolting machine, namely the collapsible drill steel enclosure. The results of the evaluation demonstrated that using the collapsible drill steel enclosure provided a 7 dB(A) reduction in sound pressure level at the operator?s position of a roof bolting machine.

Jan 1, 2008

By Krishna P. Sinha

An investigation was made to determine the creep behavior of oil shale at elevated temperatures. During the first phase of the investigation, work done on creep behavior of geologic materials was reviewed and triaxial creep tests on oil shale were planned. Tests at temperatures up to 250°C and axial stress up to 3000 psi were conducted at no confinement and at confining pressures equal to 1/3 and 2/3 of axial stress. Wide variations in the elastic properties as well as creep characteristics are exhibited. Creep deformation is more pronounced at elevated temperature but no definite quantitative remarks can be made regarding effect of grade of oil shale due to wide scatter and limited number of data paints. Primary creep can be described by a power law. Secondary creep seems to be an experimental function of deviatoric stress. Teritary creep was not observed within the test duration (24 hours in most tests).

Jan 1, 1983

By Oliver Bowles

Marble is one of tile most beautiful and enduring materials employed in the construction industries. Because of its diverse colors, decorative patterns, and varying textures, it has furnished material for artistic architectural design for many centuries. The marble industry is described in some detail in Bureau of Mines Bulletin 106, The Technology of Marble Quarrying, which, unfortunately, is now out of print but may be consul ted at most large libraries. Onyx marble and travertine are discussed in Bureau of Mines Information Circular 6751. The purpose of this paper is to describe the main features of a distinctive group of ornamental marbles known as the serpentine marbles or verde antiques.

Jan 1, 1938

By Kung-Lee Wang

This report describes the linkage of all mining sectors with all other manufacturing, services, and final demand sectors of the U.S. economy. Besides being a basic data source, it provides a framework for aggregate economic impact analysis with respect to the mining industries. The framework is an open-static input-output model specifying 48 mining industries as classified in the Standard Industrial Classification Manual for all mining activities and 76 nonmining industries which collectively exhaust, all economic activities. The 124-sector model used in this report is an expansion of the preliminary 82-industry aggregation estimates made by the Department of Commerce. In the expanded model, 48 ruining industries are substituted for the original 6. The methodology used to ascertain the industry-by-industry procurement cost estimates and product ion flows necessary to the construction and expansion of the basic 82-sector model included personal interviews, case studies of specific mining activity analysis, and published and unpublished data from the Bureau of Mines and the Census of Mineral Industries, The end products of this study are two tables arranged to show the direct purchases necessary for each industry to support the level of economic activity and the total purchases generated in each industry throughout the economy by each $1 of aggregate economic demand in 1958. The tables may he used for economic impact studies and market analysis by firms engaged in or closely associated with the mining industries. Some illustrations of their usages are presented.

Jan 1, 1967

By F. E. Armstrong

An instrument using a gamma-ray backscatter technique for determining the weight-percent incombustibles content of coal dust and rock dust mixtures in coal mines has been built and tested. The unit gives a direct readout in per-cent incombustibles for coal mine dust mixtures containing between 50 and 100 percent incombustibles; calibration of the device requires using a sample of the rock dust employed; this is usually limestone but occasionally dolomite or gypsum. A small americium-24l source is used with a scintillation detector whose output feeds a rate meter. The source-detector geometry used was chosen to reduce the effects of variation in bulk density. Accuracy of the system is within ±3 percent for most mixtures. The instrument is portable and completely self-contained; the rechargeable batteries supply power for 300 to 400 determinations.

Jan 1, 1974

By Frank S. Wartman

"The experimental flotation work described in this paper was undertaken to test the conclusions derived from a previous microscopic and chemical study of several samples of converter slag. That study3 resulted in the conclusion that approximately 90 per cent of the copper content of a converter slag wad in either the sulphide or metallic form, and that if the slag were cooled slowly the copper-bearing material would be in particles of such size that they would be freed from silicate and magnetite grains by grinding the slag to pass a 150-mesh sieve. If this were true, it should be possible to separate the copper-bearing grains from slowly cooled, converter slag by the flotation process.Many attempts, of which the author has seen no published account, have been made to treat slags, especially converter slags, by flotation. In every case these trials have been made with chilled slags, in which, as shown in the preceding report, the copper-bearing material is top finely disseminated, to be freed by any reasonable degree of grinding.The flotation tests described in this paper have shown that it is possible to recover by flotation about 30 per cent of the copper content of a converter slag containing 3 per cent copper and to obtain flotation concentrates which have a copper content of 35 per cent.Acknowledgment is made to G. L. Oldright, supervising engineer of the section of nonferrous metallurgy, U. S. Bureau of Mines, for valuable assistance and direction; to W. A. Sloan for chemical analyses; and to Alfred P. Towne for assistance in experimental manipulation."

Apr 1, 1931

By C. R. Summers

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneumatic drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115-dbA stope drill to approximately 100 dbA.

Jan 1, 1974

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitled ?Evaluation of Proximity Warning Devices? dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electrostatic fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factor of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By A. J. Kauffman

This inventory of the industrial mineral resources of the Pacific Northwest indicates that each of the States comprising this great region annually produces nonmetallic materials valued at mans million dollars. Commodities or their products that have a large, localized market predominate. These include Portland cement, sand and gravel, stone, clay, and lime. The region's output of magnesite, vermiculite, pumice, and diatomaceous earth is outstanding. The magnesite deposits of Stevens County, Wash., are the largest and most important in this country. Mast of the domestic vermiculite production is obtained from deposits in Lincoln County, Mont. Oregon and Idaho rank third and fourth, respectively, as domestic pumice producers. Production data for diatomaceous earth show Oregon second and Washington fourth among the producing States.

Jan 1, 1952

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By Thomas E. Finch

This report is an engineering-economic evaluation of alternate methods of handling the parting between two coal seams. It consists of evaluations of parting stowing techniques applicable in a representative, thick seam western United States mine. Methods are examined for their potential implementation, and an estimated operating cost per yard of material moved is developed. The methods are of two categories castback or haulback. Haulback methods use truck haulage except With scrapers, and the castback methods are a direct stowage with no intermediate haulage equipment. Possible equipment combinations include draglines, shovels, hydraulic backhoes, bucket wheel excavators, scrapers, and front end loaders. The purpose of this report is to evaluate the effective competetiveness of the various alternatives.

Jan 1, 1975

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By Eric H. Brown

One of the best methods by which the results of accident-prevention work can be measured for any particular period is to keep an accurate record of the accident experience, which may then also be compared with the experience of others. The purpose of this report is to compare records of the salt-mining companies operating in Louisiana, and their assistance in making available their accident records is gratefully acknowledged. PRODUCTION Four companies produce salt in Louisiana -Avery Salt Co., Avery Island; Jefferson Island Salt Mining Co., Jefferson Island; Myles Salt Co., Weeks; and Carey Salt Co., Winnfield. Three of these companies operate within 30 miles of each other in the southern part of the State, and the other operates in the central part.

Jan 1, 1938

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By J. Douglas Causey

In 1988, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 12,740-acre Blue Canyon Wilderness Study Area (OR-003-073) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 27 miles northwest of Jordan Valley. The study area is underlain by Tertiary welded tuff, tuff, perlite and tuffaceous sedimentary rocks capped by basalt. Jasper has been mined from several localities. Some mining has been done by hobbyists. However, the area has been covered by mining claims since 1964, with mining done by commercial operators. This region has been a source of "Owyhee picture" and other similar jaspers. More recent exploration has focused on the gold potential of nearby areas such as Quartz Mountain and Red Butte.

Jan 1, 1989

By A. C. Fieldner

All technical facilities of the Bureau of Mines have been geared for more efficient use and conservation of mining equipment, developing plans for safety, improving the quality of coal through better methods of preparation, studying the problems of coal storage and utilization, and extending the uses of coal5/ for the war and postwar economy. The Bureau is now analyzing all of the coal purchased by the Army and much of that required by the Navy. Work on boiler feed water was doubled over last year to meet the increased demand made by the War Department for protecting vital boiler plants in many new camps and defense plants. Progress has been made in safely storing coal to reduce dangers of spontaneous ignition to a minimum and to preserve coking power. Mixtures of oil and coal to be used as a substitute fuel have been investigated. Technical service on the conversion of plants to other fuels has been given to government agencies and private consumers. The possibilities of making motor fuel,

Jan 1, 1944

By M. C. Bleiweiss

Various light sources were evaluated for use in a fiber optic lighting system for mining machines. It was determined that a metal halide arc lamp was best because of its resistance to damage from shock and vibration and the high luminance of the arc. Measurements were made of the percent transmission of the ½ inch thick glass window and the fiber bundles, the total lumen output of the diffuser assembly with a known input and of the average surface luminance of the diffuser assembly. These data were then used to calculate the theoretical output of the system given an estimated input from the source. A prototype 55 watt, single-ended metal halide source was then developed. In order to provide greater efficacy and higher throughput through the fiber optic cables, a variation of the lamp with thallium iodide added to the fill was developed. The lamp was modified and a ballast was developed to allow it to hot restrike.

Jan 1, 1986

By Roger E. Burleigh

In June, 1989, the U.S. Bureau of Mines, undertook a 9-day evaluation of the tin resource potential of the Sleitat Mountain tin deposit. Significant tin-tungsten mineralization is associated with quartz-topaz-white mica-tourmaline greisen alteration of a multi-unit, 57 Ma, peraluminous, granite stock which intrudes Cretaceous Kuskokwim Group flysch deposits. The granite comprises marginal biotite-, intermediate biotite-muscovite-, and central zinnwaldite-granite units, interpreted as a zoned alteration system. Major vein mineralization is confined to two east-west-trending zones of steeply oriented tabular lenses of greisen interleaved with mildly altered granite. Cassiterite is the dominant ore mineral while arsenopyrite, loellingite, wolframite, pyrite, sphalerite, chalcopyrite, and bismuth-oxides are present in minor to trace amounts. The north and south greisen zones are estimated to contain an inferred resource of 128 to 212 million lbs Sn in 28.6 million st of mineralized rock. An 1,800-lb representative bulk sample contained 0.37% Sn, 0.04% W and 17 ppm Ag and is considered an average grade estimate for the deposit. Drill testing by Cominco Alaska Exploration indicates that substantial widths of high-grade tin mineralization are included within the lower grade disseminated mineralization. Depth of deposit erosion is substantial and there exists a high probability for placer tin deposits.

Jan 1, 1991

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984