Search Documents

By Kenneth M. Earl

In its program of investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the Tapley deposit in an endeavor to find an additional source of copper. There are accounts that many years ago the property had some production; there are several old, inaccessible shafts apparently sunk on a vein in rhyolite or diabase. The waste dumps of these shafts contain considerable sulfides, chiefly pyrite and chalcopyrite. To cut the vein below the old mine workings, the Bureau of Mines? diamond-drilled five holes aggregating 1,204 feet. No significant copper mineralization was found.

Jan 1, 1950

By John P. Gooch

The Bureau of Mines wrote a computer program which calculates the saturation curves and condensation characteristics of gaseous mixtures consisting of binary organic vapor and air. The program employs an algorithm which assumes an equilibrium mechanism for condensation, and the degree of fractionation obtained is predicted on the basis of relative volatility. The program incorporates a feature which allows the user to examine the fractionation resulting from condensation as a function of the size of the temperature increments over which condensation is assumed to occur. If a single. temperature interval between the dewpoint of the mixture and the outlet temperature of the condenser is assumed for the calculation, the results obtained will be those resulting from a single equilibrium condensation. If the condensation is assumed to occur over a number of temperature increments, the results obtained will approach those predicted by the Rayleigh equation as the magnitude of the temperature increments approaches zero. The results from calculations performed on vapor mixtures from organic heavy liquid solutions used in beneficiating potash and brucite ores are presented. The liquids are solutions of dibromomethane in trichloroethylene or perchloroethylene. The results show the degree of liquid recovery which is possible by cooling mixtures of organic vapor in air. Compositions of the vapor range from 10 to 95 percent air, and assumed condenser exit temperatures range from 110° to 50° F.

Jan 1, 1971

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free-port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Its estimated recoverable reserves in Fayette County are between 670 and 800 million tons. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal.

Jan 1, 1977

By C. Özgen Karacan

Methane emissions from a longwall ventilation system are an important indicator of how much methane a particular mine is producing and how much air should be provided to keep the methane levels under statutory limits. Knowing the amount of ventilation methane emission is also important for environmental considerations and for identifying opportunities to capture and utilize the methane for energy production. Prediction of methane emissions before mining is difficult since it depends on a number of geological, geographical, and operational factors. This study proposes a principle component analysis (PCA) and artificial neural network (ANN)-based approach to predict the ventilation methane emission rates of U.S. longwall mines. Ventilation emission data obtained from 63 longwall mines in 10 states for the years between 1985 and 2005 were combined with corresponding coalbed properties, geographical information, and longwall operation parameters. The compiled database resulted in 17 parameters that potentially impacted emissions. PCA was used to determine those variables that most influenced ventilation emissions and were considered for further predictive modeling using ANN. Different combinations of variables in the data set and network structures were used for network training and testing to achieve minimum mean square errors and high correlations between measurements and predictions. The resultant ANN model using nine main input variables was superior to multilinear and second-order non-linear models for predicting the new data. The ANN model predicted methane emissions with high accuracy. It is concluded that the model can be used as a predictive tool since it includes those factors that influence longwall ventilation emission rates.

By Martyn F. Roetter

The work of the operational communication systems' group dealt with a range of communication needs and functions within mines, primarily along haulageways, to and within sections up to the working face itself, and in mine shafts. A mixture of communication techniques and hardware is needed to satisfy this variety of communication needs within the differing environments encountered in U.S. mines. Substantial progress, both experimental and theoretical, has been made in recent years towards developing alternative communication systems suitable for use in mines which are based on "guided" waves, including wire-less (waveguide-like propagation in mine tunnels) and wire-based systems (leaky coaxial cables or wires) . Major priorities identified for further work needed to confirm (or deny) the applicability, and refine the operational specifications of promising communication systems for mine use include: Short-Term Projects o Cost/performance analyses of promising leaky coaxial cable and UHF radio communication systems which require further data from: - Experimental investigation under U.S. mine conditions of the performance of potentially applicable leaky coaxial cable communication systems developed in Europe (France, Belgium, and the U.K). - Cost estimates on these coaxial cable communication systems. - Measurements of UHF radio propagation in low-coal mines. - Investigation of the influence of obstacles (e.g. shuttle cars and section machinery) in the entries on UHF radio propagation in mines. o Investigation of the problems of transmitter and receiver coupling and termination matching associated with the two-way propagation of low frequency radio waves in hoist shafts.

Jan 1, 1973

By Larry G. Stolarczyk

1.0 FRAMEWORK FOR COMPARISON This document describes the decision factors that bear on the selection of the modulation process for the wireless underground medium frequency (MF) communication system. The selected modulation process must satisfy the Bureau of Mines stated objective of improving general communications within an underground mine. The improvement being sought includes the development of a wireless communication technology of measurable benefit to both mine safety and mine productivity. The improvement will allow wireless communications paths to exist between roving miners. The wireless communication paths will also be made compatible with the existing underground telephone system to extend paging and voice communication throughout the underground mine. The new wireless equipment will include man-pack, vehicular, repeater, and base station transceivers. Repeaters and base stations will feature coupling networks for interfacing with the existing telephone circuits. Frequency modulation (FM) and single sideband (SSB) modulation processes are analyzed in view of the special conditions associated with underground mining. Of primary importance is the tremendous electrical noise generated in an operating mine that could adversely affect communications quality. High noise coupled with high attenuation rate of near field signals forces the communication system to be inherently short range. Fortunately, near field signals can propagate over great distances on underground wires and cables. The framework for comparison is generated by presenting all factors that

By C. W. Davis

Before listing the laboratories and the work performed there, it is proper to make clear what is done and what is not done by Federal bureaus, States, and Territories, as well as by countries to the north and south of the United States. FEDERAL Bureau of Mines. - The Bureau of Mines does not make assays or analyses for individuals or firms unless the samples are part of the ore-testing and ore-dressing investigations of the Metallurgical Division on representative ores from mining districts and of possible benefit to the entire mineral industry through published reports. All significant results obtained in this way are made public. Any mineral sample sent to this Bureau for simple identification will be examined.

Jan 1, 1938

By Edward A. Mihok

This paper presents plant design and cost estimates for limestone treatment of acid mine water covering a wide range of quality and quantity conditions. The treatment process consists of limestone neutralization, aeration, solids settling, and concentration. The design criteria for the various operation functions are based on pilot plant performance, laboratory data, and established mine water treatment standards. Unit costs have been assumed and are related to general market prices and conditions. These estimates serve as preliminary indicators of what it would cost to construct and operate a mine water treatment plant.

Jan 1, 1970

By Thomas R. Bur

The order of identification and in same cases the magnitude of the elastic constants of an anisotropic material depends on the orientation of the cartesian coordinate axes with respect to a set of reference coordinate axes within the material; thus confusion will result unless standard orientations are used. In this paper the relationship between the cause (the internal fabric) and the effect (the elastic properties in this case) is discussed for single crystals and for polycrystalline and amorphous materials. While reference axes based on the cause are used in the IRE (Institute of Radio Engineers) standard for piezoelectric crystals) it is shown that a reference coordinate system that would be suitable and practical for all anisotropic polycrystalline and amorphous materials must be based directly on a three-dimensional expression of the effect. The conventions offered are similar to the IRE standards for piezoelectric crystals) but use the elastic coordinates of the wave surface which can be quite readily established experimentally as the reference coordinates.

Jan 1, 1969

By J. W. Eckerd

Metal production rates of 42 to 45 tons per day were obtained with hollow-core anthracite briquets in an experimental blast furnace. Tuyere pressures were about the same for both coke and briquet operations, but from 150 to 175 pounds more of briquets were required per ton of metal than were needed with coke. Furnace operations were comparatively smooth, furnace hanging occurring less often than in previous tests with anthracite briquets. Dust production was substantially higher than with coke, however, and metal quality could not be controlled by corrective burdening and moisture control.

Jan 1, 1968

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

Provide blasting-resistant, quickly reusable stoppings for large mine openings. Approach Stoppings are assembled using roof-to-bottom panels of brattice held together by Velcro seams that peel open when struck by a strong air blast. How It Works The Velcro seam is designed to open when exposed to forces lower than would normally damage the brattice. When the seams partially open, they relieve the blast air overpressure to prevent damage to the brattice panels and their anchoring devices. A stopping is returned to service by reclosing the Velcro seams. To hang a brattice panel, its top is stapled to a board, and wrapped once or twice around it. That assembly is then attached to the roof with bolts. The length of the board should be a foot less than the width of the panel to allow for the sealing seam on each side of the panel. The boards are installed end-to-end in an approximately straight line across the roof of the mine opening.

Jan 1, 1979

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) conducted a study of the explosibility of various metals and other elemental dusts, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafnium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties-from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechnic ignitors. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from "-1550K for tin and tungsten powders to "-2800K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures.

To cool hot working environments in deep mines more efficiently, while substantially reducing the maintenance required by presently used cooling coil heat exchangers. Approach A mine's chilled water supply cools fresh air enroute to hot working areas, in an improved, direct-mixing heat exchanger. How It Works Warm, fresh ventilation air traveling through the mine's ventilation tubing enters the lower portion of the cooler heat exchanger through a large round opening designed to accept the ventilation duct. This air flow is turned upward and evenly distributed by egg-crate lattice and pair guide vans at the bottom of the cooler. On the diagram, warm air enters at the bottom left. As the air moves upward through the cooler, it passes through a plastic or wire mesh pad which is arranged so that it offers the most resistance to upward airflow immediately above the cooler inlet: this more or less equalizes the upward air flow along the length of the cooler. The air next moves through the cold water sprays, and then through a wire-mesh demister pad before exiting from the cooler at the top right. Cooling of the air is accomplished in several stages. As the incoming air passes through the lower plastic or wire mesh pad, it is exposed to water flowing downward through the pad to the water sump. This is water that has fallen from the sprays or dripped from the upper wire-mesh mist eliminator. This water is slightly warmer than the spray water since it has already done some cooling,

Jan 1, 1981

By F. L. Wideman

Materials handled at metal and non-metal mines in the United States increased 10 percent compared with those of 1965 as a result of expansions in output at existing mines and development of others to meet increasing demands for mineral products. The tonnage of commercial materials mined or quarried increased as did the quantity of waste handled. Crude material from which metal or nonmetal products were derived comprised 71 percent (75 percent in 1964) of the total materials handled. Great strides were made in mining technology and there were indications that, in the future, earth moving by the mining industry will involve materials-handling systems of increasing size and complexity. Materials Handled.-Output of ore and waste at metal and nonmetal mines and quarries in the United States in 1966 totaled 3,518 million tons (3.213 million tons in 1965). The quantity of materials handled has increased at an average annual rate of 5 percent since 1962. Ore production increased 4 percent over that of 1965, also comparable to the average annual rate of increase in the last 5 years. Waste removal in 1966 increased 25 percent over that of the previous year.

Jan 1, 1967

By Charles L. Kimbell

The final tables of this chapter, tables 25-50, extend and expand the statistical series on production that was started in the 1963 edition of the Area Reports: International Volume of the Minerals Yearbook and that was subsequently updated and expanded in the 1965 and 1967-90 editions. Continuing the practice started in 1989, a column has been included in each of these tables providing a 5-year average for 1987-91, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1991. This group of tables now includes each of the crude minerals that ranked from? 1st to 19th in 1983 terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93 % of the estimated value of world crude mineral production in 1983. In addition, world output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-is included because of their significance as products.

Jan 1, 1993

By Launa Mallett, Charles Vaught, Michael J. Bmick

Since 1991 the Pittsburgh Research Center (PRC formerly part of the U. S. Bureau of Mines) has been tapping u valuable resource-researchers have recorded extensive interviews will, 30 individuals who are recognized as experts in the area of mine emergency response. These veterans related stories and observations from events experienced during as many as 47 years of response activities. Overall, the response veterans averaged 29 years of mine emergency response experience and 35 years mining experience. Individuals [ ] interviewed included representatives from mining companies, the UMWA and state and federal government agencies. This information was gathered so dial it could he provided to today's miners and to tomorrow's emergency response personnel. It is hoped the collective wisdom that has been obtained can be used to help train new responders and guide those decisions which mill have to be made on the scenes of future events. During interviews file emergency response experts were asked to discuss lessons they had learned through experience. The interviewers asked them to tell what they had learned that would cause them to handle similar situations differently and to tell about things they saw at past events shat the would warn others not to do in the future. In response the experts discussed a variety of things. Most of their responses, however, touched on some of the same topics including: preparedness, experience people on-site mine rescue teams, and decision making. A summary of their responses provides alt overview of [lie lessons learned on-site at tile largest mine disasters in the country.

By M. L. Whisman

The Bureau of Mines developed a radiotracer method for detecting the contribution of selected components and additives to thermally induce deposits of turbine aircraft fuels. Fuels were examined before and after 52 weeks of storage at 130° F. Of particular concern was the influence of aromatic hydrocarbon fuel constituents on thermal-stability quality of jet fuels during storage. A microfuel coker test apparatus was used to thermally stress the test fuels and blends, and the resultant contribution to deposits of selected fuel components, labeled with carbon-14, was determined by radioactive-counting techniques. Ninety-one blends of five test fuels with carbon-14-labeled fuel additives or components were prepared, tested, stored for 52 weeks at 130° F, and reanalyzed for deposit-forming tendency. These additives included two anti-oxidants, a metal deactivator, and a corrosion inhibitor. Of the labeled hydrocarbon fuel systems studied, the greatest reaction was observed in blends containing methyl-and ethyl-substituted indenes. Other aromatic types also showed some contribution to the deposits. Three of the additives showed a marked tendency to degrade and react during storage and thermal stress. A cresol antioxidant, however, barely contributed to deposit formation. Oleic acid interacted with cadmium present in aircraft fuel systems and produced deleterious effects upon the thermal-stability quality of the fuel.

Jan 1, 1971

The Mine Safety and Health Administration (MSHA) defines an independent contractor as "any person, partnership, corporation, subsidiary of a corporation, firm, association or other organization that contracts to perform services or construction at a mine." Contractors that perform specific types of work are required to report the number of employees who perform work at coal mines and at noncoal mines.

Feb 1, 2005

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997