Search Documents

By W. F. Marshall

The effect of engine parameters on exhaust emissions from two diesel engines was studied experimentally. Fuel-injection characteristics and intake air conditions were considered as parameters influencing the emissions. Emphasis was placed on the effect of parameter variations on nitrogen oxide (NOx) emissions, because diesels generally emit very low levels of carbon monoxide (CO) and unburned hydrocarbons. Emissions other than NOx were at lowest levels when the engines were adjusted for best performance. NOx emissions can be diminished somewhat through variation in fuel-injection characteristics, but there generally are penalties in emissions of CO, smoke, and unburned hydrocarbons or in engine performance. Temperature and composition of intake air have a significant effect on NOx emissions. Levels of NOx are reduced by recirculating the exhaust gas or by adding water to the intake air stream. However, the rate of water added or exhaust gas recirculated must be limited to prevent the degradation of engine performance and increased emissions of CO and smoke. At high exhaust recirculation rates, levels of CO and smoke were increased such that it was necessary to derate the engine and also to use a catalytic system for oxidation of CO.

Jan 1, 1971

By B. W. Gandrud

[The meaning of the term "bauxite' has always been somewhat vague and indefinite, and the term has been used in various applications to denote sometimes a rock, sometimes a mineral, but more frequently an ore. It seems logical to think of bauxite as an ore, however, because a very large part (probably at least 85 per cent) of the entire world's production of bauxite is at present being used as a source of aluminum and aluminum chemicals. In the United States there are two districts that, produce bauxite - the Arkansas district and the Alabama-Georgia-Tennessee-Mississippi district. The deposits in Mississippi have been discovered recently and are riot as yet productive but it seems reasonable to consider them as apart of the-district hat includes the deposits of Alabama, Georgia, and Tennessee. The, two districts are often referred to as the Arkansas field and the Appalachian field. Of these two the Arkansas field has been by far the largest producer, and at present over 90 per cent of the bauxite production of they United States comes from the Arkansas field. The bauxite industry in the Appalachian field had its beginning in 1889, and since that time the total production of the states of Alabama, Georgia, and Tennessee has been, nearly a million tons. The production of bauxite in this field has languished in the last five, or six, years, and In 1927 its production was only about 14,000 tons, according to Harder4. The recent decrease in production is due mainly to the fact that many .of the known deposits of commercial-grade ore have become exhausted. There are, however, considerable quantities of low-grade bauxite in the Appalachian field, but these have not been available because there has been no satisfactory way of concentrating low-grade bauxite. The quantity, of low-grade material in the Appalachian field is probably, fully as large as the tonnage of commercial ore which the field has already produced.]

Jan 1, 1928

Provide a more efficient method of cooling hot working environments in deep mines than is possible with single stage spray coolers or cooling coil heat exchangers. Approach Pass warm mine air through several stages of horizontally oriented water sprays fed by the chilled water supply of the mine. How It Works This concept extends the capabilities and potential applications of the coolers described in Technology News nos. 71 and 93. In this multi-stage design, hot ventilation air is cooled while passing through horizontal water sprays. Air enters the cooler through a diffuser section which slows the airflow and distributes it evenly across the cooler with a minimum of pressure drop. This ensures uniform exposure of the warm air to the cool water and consequent high thermal efficiencies. In the three-stage cooler shown, cold mine service water is sprayed from the first water stage manifold on the downwind end of the cooler. Slightly warmed water from this spray stage is collected in a sump, pumped and then resprayed through the second stage manifold. The process is repeated again for the third-stage. An overall counterflow heat exchange effect is thus achieved by exposing the hottest incoming air to the warmer, third-stage water spray first and to the coldest, first-stage water spray last. Wave plate eliminators can be employed between stages of water sprays to increase thermal efficiency or at the outlet to minimize the water discharged into the mine ventilation air. Cooled air can then be ducted to hot work spaces or simply released

Jan 1, 1985

Experience, it is said, is the best teacher. Some experiences, however, should be shared so that no one else will ever have to live through them again. The fire at the Sunshine Mine is one such experience. ?Hard-rock mines don?t burn.? The Sunshine Mine near Kellogg, ID, was the nation?s premier silver producer for many years. In 1972, the mine was nearly 6,000 feet deep, contained hundreds of miles of worked-out areas, and employed nearly 500 people. Because of its depth and the type of host rock for the silver (unburnable quartzite), the general thinking of the day was that fires in mines such as the Sunshine were impossible, because ?hard-rock mines don?t burn.? What wasn?t really considered was that timber supports, foam insulation, and mining equipment do burn and that the carbon monoxide gas produced by burning is far more deadly than fire itself. Thus, no one was prepared when, on May 2, 1972, a fire of un-known origin broke out below the 3100 level of the mine. Before long, 173 miners on the day shift were trapped by thick, black smoke. By the time the fire was out, 91 miners had died, and the Sunshine Mine Fire became known as one of the worst mine disasters of the 20th century. It became the catalyst for passage of the Metal/Nonmetal Health and Safety Act of 1977, which applied the same federal safety standards to hard-rock mines as those regulating coal. Mandated safety training, mine inspections, and equipment standards were brought into force.

Aug 1, 2002

By Vijia K. Karra

The goal of aggregates producing companies across the United States is to ensure their workers go home safely each day. At the National Institute for Occupational Safety and Health (NIOSH), researchers are pursuing this vision of safety and health through a fact-finding approach for reducing injury illness in various mineral sectors. Surveillance data from Mine Safety and Health Administration (MSHA) has been the source for such analyses. It helps to focus research efforts on key machinery, workers, and their tasks. The second installment of this two-part series follows last month's focus on crushed stone.

By Robert P. Vinson

A sequential sampler, based on the Archimedes screw, has been developed by the Bureau of Mines. Its initial purpose was to collect air samples during tracer gas studies in underground mines. However, the basic concept can be applied to other sampling needs, including sampling of liquids. A prototype was built and successfully tested in the Bureau's Experimental Mine at Bruceton, Pa. The simple design makes the sampler inherently durable and low in cost.

Jan 1, 1976

By Roy F. Abernethy

This report describes a method developed by the Bureau of Mines for the determination of beryllium in coal ash. Samples are put into solution by standard wet chemical procedures. Interfering elements are complexed with Na2EDTA, and the beryllium is separated by extraction of its acetyl acetone complex with chloroform or carbon tetrachloride. Final determination is made with Beryllon II.

Jan 1, 1970

By M. MacLaughlin, J. Whyatt

A case study is presented that relates statistical descriptions of joint sets to the distribution of local wedge failures along the crest of a catch bench at the Yellowstone Talc Mine. The fracture sets and bench width were mapped by teams of geological engineering students from Montana Tech under the direction of Dr. Mary MacLaughlin. The students analyzed the fracture data, conducted physical property tests, and used a beta version of a NIOSH program “Bwedge” to predict the distribution of surviving bench widths. In the course of this analysis the students developed evidence of software performance issues that, unfortunately, frustrated their analysis. These have now been addressed and a full analysis completed. The analysis confirms the validity of the student mapping program and provides insight into the effects of blasting and excavation practices on the bench. It also provides a tool for exploring the pattern of bench crest failure that would result from variations in both bench geometry and blasting practices.

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

By Ben A. Kornhauser

Benin's industrial sector experienced severe economic and financial problems in 1986, including disappointing performances of the Onigbolo cement plant and the Semé Oilfield, plus a shortage of technically trained personnel and experienced management. Oil production remained about 1,000 barrels per day. Import and export trade between Benin and the United States remained minimal. Because much of Benin's outstanding external debt was in U.S. dollars, the stronger dollar greatly increased the debt burden. The 1985 budget of $304 million' was composed of an investment budget of $194 million and a current budget of $110 million. Of the investment budget, 84% was expected to be externally financed. About $45 million was given to three priority projects: the joint Benin-Togo Nangbeto hydroelectric project scheduled for completion in 1986; drilling of new exploratory wells of the Semé petroleum project, and the Dassa-Parakou highway. The budget deficit was projected to exceed $43 million despite a decrease in projected revenue owing to an anticipated decline of 25% in import tax revenue, normally the largest source of Government revenue.

Jan 1, 1987

The following methods should be used to protect miners from the adverse health effects of exposure to respirable coal mine dust and respirable crystalline silica: ? Informing workers about hazards ? Establishing written emergency procedures ? Using engineering controls, work practices, and personal protective equipment (including respiratory protection when dust control equipment is being installed, maintained, or repaired) ? Monitoring exposures ? Conducting medical screening and surveillance ? Encouraging smoking cessation ? Maintaining medical records

Jan 1, 1997

By Thomas F. Tomb

The penetration characteristics of a horizontal plate elutriator and of a 10-mm nylon cyclone were evaluated. The test aerosols were polydisperse coal-dust particles ranging from less than 0.3 to 15 micrometers in diameter. Particle densities ranged from 1.3 to 1.4 grams per cubic centimeter. Equivalent Stokes diameters were measured using Coulter counter analytical techniques. Experimental results indicate that the penetration characteristics of the horizontal plate elutriator closely approximate the sampling efficiency curve defining the respirable fraction of the dust cloud recommended and adopted by the Johannesburg Pneumoconiosis Conference in 1959. Penetration characteris-tics of the 10-mm cyclone were evaluated at flow rates of 1.4, 1.5, 2.0, 2.5, and 2.8 liters of air per minute. The data indicate that the penetration curve obtained at 2.0 liters per minute most closely approximates the sampling efficiency curve for respirable dust recommended at a meeting sponsored by the U.S. Atomic Energy Commission in 1961.

Jan 1, 1970

Provide the U.S. mining industry with the means to measure and control exhaust emissions of diesel engines used in underground mines. Approach Diesel research is divided into four primary areas: exhaust aerosol measurement, particulate control, gaseous emission control, and chemical and biological characterizition of particulate matter. Diesel research is frequently cosponsored by industry; collaborative research ventures between industry, academia, other government agencies, and the Bureau arc common. Diesel research at the Bureau is conducted in the diesel engine research facility at the Bureau?s Twin Cities Research Center (TCRC). This facility is a state-of-the-art laboratory capable of performing emissions testing, exhaust control evaluations, and safety tests. Background Exposure of mine workers to airborne contaminants from diesel engine exhaust is potentially harmful. The National Institute for Occupational Safety and Health has recommended that whole diesel exhaust be regarded as "a potential occupational carcinogen" and that ?reductions in exposure to diesel exhaust in the workplace would reduce the risk." The U.S. Mine Safely and Health Administration (MSHA) convened an Advisory Committee on Standards and Regulations for Diesel-Powered Equipment and is beginning to implement its recommendations, which cover health, safety, and certification and approval issues surrounding the use of diesels underground. In January 1992, MSHA published an advance notice of proposed rulemaking to regulate diesel particulate matter in underground mines.

Jan 1, 1992

Permit quicker, safer clearance of hang-ups in the ore passes and chutes of underground mines. Approach Develop a device that can be operated from a safe distance to explosively propel a projectile into the hang-up. How It Works The Hang-Up Clearance Module, consisting of a stand, steel disk, explosive charge, and aiming device, is placed at a location convenient for line of sight aiming at the hang-up. This placement can be more than 100 feet from the target. Once aimed, the charge is remotely detonated, and the disk is converted by explosive force into a slug and propelled to the hang-up, bringing it down. The steel disk and an explosive charge are contained by a plastic casing. A small booster which is placed at the rear center of the explosive makes up the last component of the charge. Initiation is accomplished by standard means such as detonating cord or a number 8 blasting cap. When Initiated, a detonation wave travels through the explosive, inverting and consolidating the steel disk into a large slug. This slug is propelled at high velocity to the hang-up, delivering more than 5 million foot-pounds of energy on impact.

Jan 1, 1981

By Pablo Velasco

Ecuador had limited mineral output, al-though the Government attempted to stimulate metallic mineral exploration and also evaluated a gypsum and a phosphate deposit. A pilot plant to exploit gold deposits was established, and there was extensive gold exploration activity in southern Ecuador. Domestic output of iron and steel declined sharply. Among all minerals, petroleum output was the dominant factor with both exports and production increasing significantly over that of 1988. Crude oil exports contributed 63% of total export earnings and about 70% of the central Government's revenue.

Jan 1, 1986

Compare the fire endurance of paneled steel stoppings with that of traditional concrete block Stoppings. Background Permanent stoppings or partitions arc used in mines to separate ventilation airways. The ability of stoppings to retain their structural integrity for a minimum length of time under lire conditions and prevent the spread of flame and toxic combustion products to an adjacent airway is critical. The success of miners in reaching safety during a fire depends largely on the presence of uncontaminated airways. Traditionally, permanent stoppings for coal mines are constructed of concrete blocks. Recently, paneled steel stoppings that satisfy many of the requirements demanded of permanent stoppings, such as incombustibility and strength, have been introduced. Their use also introduced concerns such as the ability of a steel stopping to maintain its ventilation control function when exposed to a fire and the potential that the fire could transmit enough heat through the stopping to ignite combustible materials on the unexposed side. To address these concerns, the Bureau of Mines investigated the fire endurance of galvanized steel and concrete block stoppings.

Jan 1, 1989

Improve the performance of waterjet nozzles used for water-jet-assisted cutting to optimize rock cutting efficiency. Approach The performance of a longwall shearer equipped for water-jet-assisted cutting was evaluated during an earlier study (Tech News No. 277). Waterjet nozzles were used to direct the solid streams of water that impacted the rock near the tip bits. The maximum water pressure that could be delivered to the nozzles was about 6,000 psi. Due to the "break up" of the solid stream of water, some of this pressure was lost before the water reached the rock. The pressure could have been increased by moving the nozzle closer to the bit tip but) moving the nozzle too close increases the possibility of damage to the nozzle. Study Results A test apparatus was built to measure water pressure at the location of water jet impact (see illustration). The target, a tungsten carbide plate with a 0.013 inch diameter orifice, was placed at the location of water jet impact. A pressure transducer, used to monitor impact water pressure, was positioned under the plate. Water pressure at the nozzle was maintained at 6,000 psi. The distance between the nozzle and target was varied from 2 to 5 inches.

Jan 1, 1988

This book has employed miners' narratives to illustrate basic concepts about the escape process. One of the most powerful means by which people make sense of their experiences is through the telling and internalization of stories [Bruner 1990]. By couching one's own and others' motives and actions in terms of a coherent narrative, a person is able to learn from mistakes and plan future behaviors that may help ensure survival. A growing body of research suggests that decision-making skills used to deal with emergency situations can be taught and assessed by simulations based on narratives from the real world [Bransford et al. 1986; Brecke 1982; Brener 1984; Connolly et al. 1989; Halff et al. 1986; Jones and Keith 1983; Lacefield and Cole 1986]. Such techniques have been used to address the decision-making of medical personnel, civil and military flight crews, and even people involved in broader life events such as political and military situations [Babbott and Halter 1983; Dugdale et al. 1982; Farrand et al. 1982; Gilbert 1975; McGuire 1985; McGuire et al. 1976; Flathers et al. 1982; Giffin and Rockwell 1984; Jensen 1982; Janis and Mann 1987]. Given the validity of this method of study and the promise it holds for helping people improve the quality of their responses to nonroutine occurrences, it is perhaps surprising that there have been no studies of emergency decision-making among blue-collar workers prior to those conducted by the present authors and their colleagues. The purpose of this chapter is to describe underground coal miners' decision-making performance on a table-top simulation whose problem structure is derived from interviews with a group of eight miners who escaped from the 5 Left section at Brownfield Mine. The exercise was constructed by a panel of domain experts (mine safety and rescue personnel) with the assistance of an educational psychologist. The simulation includes actual predicaments with wise and unwise decision alternatives that, in the opinion of these domain experts, are characteristic of such escapes. Results reported in this chapter are the scores of a sample of experienced mine workers who completed the simulation. Because the exercise is a series of objective performance tasks coupled with detailed and immediate feedback, this simulation can be used to teach and refresh critical escape skills, as well as to provide data concerning the proficiency of miners at the time of exercise administration.

Jan 1, 2000

By Paul T. Allsman

Iron-ore deposits in southwestern Utah, as the major source of iron ore for western steel plants, were investigated by the Bureau of Mines in 1942-45 in cooperation with property owners and operators and with the assistance of the United States Geological Survey with a view to determining and extending the known reserves. The factual data resulting from that project were presented in a previous report and in a report on the geophysical surveys now in course of publication. The present report has been prepared in response to expressed public interest in the ore reserves of Iron County. Mining began in the district in 1871} but. did not become important until 41 1923. From 1923 to 1946, inclusive) production totaled 10,139,500 long tons. In 1945 the district yielded 1,931,749 long tons containing 52.84 percent iron; in 1946 the corresponding figures were 1,317,671 and 53.75. The deposits lie .in a narrow, 23-mile long belt extending northeasterly from Washington 'County into Iron County along a line of mountains, chief of which are Iron Mountain, Granite Mountain, 'and Three Peaks in Iron. County. The deposits are hematite-magnetite bodies, chiefly in limestone near its contact with the monzonite of the mountain masses, but with a few important veinlike bodies in the monzonite or at the contact. They range in size from small pods to several millions of tons, and in depth from surface or near-surface to a known maximum of 1,300 feet:

Jan 1, 1948

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) IS linked to cumulative back, neck, and abdominal disorders. In low-coal mines, space restrictions make seat suspensions difficult to use in isolating operators from shock and WBV. Researchers at NIOSH, Pittsburgh Research Laboratory, are responding to these issues by investigating viscoelastic foams. For the full-load case. an ergonomic seat with viscoelastic foams isolated the shuttle car operator from shock at 15 Hz. Researchers used results from additional foam testing with an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.