Search Documents

By M. S. Moats, C. M. Campbell

Samples of a high impurity (90.05 wt. % Cu, 4076 ppm Pb, 1939 ppm As and 635 ppm Bi) commercial copper anode were characterized and then electrorefined in a laboratory scale cell. Anode inclusions were examined using backscatter mode scanning electron microscopy and energy dispersive spectroscopy. Hundreds of inclusions were measured for size, morphology and composition. Commonly found inclusions were copper oxide (Cu2O), complex oxides (Cu-Pb-Bi-As-O) and copper selenides/tellurides. The weight percent of lead and arsenic increased with increasing inclusion size up to 4- 5 microns. During electrorefining, starter sheet ductility was negatively impacted by thiourea addition. The importance of arsenic (V) concentration on the electrolyte concentration of bismuth was observed. INTRODUCTION Copper electrorefining is a commercial process used to produce the majority of the world’s refined copper. During this process, impure copper anodes are dissolved electrolytically, and high purity copper is deposited on cathodes. As the anodes dissolve, the impurities either accumulate in the electrolyte or report to solids that form on anodes surfaces or at the bottom of the refining cell. These solids are called slimes. Slimes contain precious metals and are collected for further processing. Slimes are also an important outlet for problem impurities such as lead, antimony and bismuth. The electrorefining process is operated in such a way to encourage the deportment of these elements to the slimes. Impurities in copper anodes have been studied extensively by Chen and Dutrizac (1990, 1993 and 2005). The most common impurities found in modern copper anodes include: Ag, As, Au, Bi, Fe, Ni, O, Pb, Sb, Se, Sn and Te. Impure copper anodes are produced by pyrometallurgical methods and have purities ranging from 97.7–99.7% Cu (Moats et al., 2019). The composition ranges of commercial copper anodes from the 2019 worldwide tankhouse survey are given in Table 1. The concentrations of anode impurities vary widely dependent on the source material and prior processing steps. Based on the work of Chen and Dutrizac, both gold and silver are predominantly found in solid solution within the copper grains while a minor amount of Ag can be found in Cu2(Se/Te) inclusions. Nickel is entirely soluble within the copper grains up to anode compositions of 2500–3000 ppm Ni; above which NiO and kupferglimmer phases are formed (Chen & Dutrizac, 1990). As, Bi, Pb and Sb are found in solid solution within copper and within oxide inclusions typically found along grain boundaries. Oxides are formed due to the presence of 0.13-0.18 wt. % O (Chen & Dutrizac, 1990). This is because during solidification of the cast anodes, impurities are enriched in the liquid phase as the copper grains nucleate and grow. The inclusions form from the last liquid to freeze, which is typically along grain boundaries (Wenzl & Filzwieser, 2007; Wenzl, Filzwieser, Mori & Pesl, 2008).

Jan 1, 2019

?Podolsky Water treatment plant discharges to Norman North bog which drains into Whistle / Post Creek watershed and into Wanapitei Lake ?Whistle Mine closed and reclaimed but continues to treat and discharge water to Whistle Creek

May 1, 2009

By S. Balideh

A good understanding of the behavior of rock helps us to make more informed decisions regarding geo-structures. Engineers need accurate equations to calculate the strength and deformation of rock before and after failure. Previous studies explain the failure of rock to ultimate strength, and laboratory tests adequately determine the ultimate strength and deformation modulus of rock. However, there are few comprehensive equations to determine the post-failure strength and deformation of rock. Previous work shows that the post-failure behavior of rock depends on the behavior of the broken rock particles after failure. The following question is then posed: How can the post-failure behavior of rock be determined by the behavior of broken rock particles? In order to answer the question, this study pursues three objectives: (i) to explain the behavior of broken rock at low confining pressure; (ii) to estimate the behavior of broken rock via the extrapolation of scaled laboratory testing; and to suggest a procedure (iii) to outline the post-failure behavior of a rock mass at low confining pressure commensurate with the behavior of broken rock in a rock mass.

Aug 1, 2013

By W. J. Jenner

"Introduction The Saskatchewan Power Corporation is a provincial crown corporation which operates under a mandate to supply all customers within Saskatchewan with electricity and natural gas. The Saskatchewan Power Corporation operates two coal mines within the province of Saskatchewan. The Souris Valley Mine is located a few miles south of the city of Estevan and produces approximately 300 000 Mg of lignite per year. The lignite is shipped about four kilometres by truck and burned at the 882 MW Boundary Dam Power Station, also owned by the Saskatchewan Power Corporation. The Poplar River Mine is located just south-west of the town of Coronach, Saskatchewan which is some 190 kilo metres west of Estevan. This mine produces approximately 1 675 000 Mg of lignite per year. The lignite is shipped seven miles by rail to the Saskatchewan Power Corporation's Poplar River Power Station. The Poplar River Mine is the sole sup plier of fuel to the Poplar River Power Station, which generates some 300 MW of electrical power. A second 300 MW unit is due to be commissioned at the Poplar River Power Station in mid-1983 and the Poplar River Mine will have doubled its capacity to approximately 3 350 000 Mg per year by that time: Souris Valley Mine Geology The Souris Valley Mine extracts lignite from the Estevan seam of the Ravenscrag Formation. This formation is of Tertiary age and was deposited during the Paleocene Epoch. The Ravenscrag Formation outcrops throughout southern Saskatachewan and all coal mined in the province occurs in this formation. Ravenscrag sediments are deltaic in origin and are composed of a series of fine sands, silts, clay and lignite deposits."

Jan 1, 1985

By S. Nikolic, H. M. Henao

"There is renewed interest in the improvement of existing copper smelting processes and the development of new technologies. It has become clear that further accurate information on slag properties, in particular, on phase equilibria are required in order to optimize these processes. It is in this context that improved experimental research methodologies have been developed specifically to provide information on phase equilibria at the oxygen partial pressures encountered in copper smelting practice. The methodology involves synthetic slag equilibration at controlled gas atmospheres, quenching and measurement of compositions of phases with an electron probe X-ray microanalyser (EPMA) with wavelength dispersive detectors (WDD). Application of modem analytical tools and careful design of experiments greatly improve accuracy of determination of phase equilibria in complex, multi-phase slag systems. New experimental data on phase equilibria for the copper smelting and converting silicate slags at controlled oxygen partial pressures in the temperature range between 1200°C and 1350°C in the ""Fe0""-Ca0-SiO2 system and in the ""Cu20""-""Fe0""-Ca0-Si02 system in equilibrium with metallic copper are reported, and differences between various data sources are analyzed."

Jan 1, 2007

By K. Tarr

Acid-producing mine tailings are present at many active and inactive mine sites and pose an environmental liability due to the potential for acid rock drainage. Acid rock drainage originating from a tailings pile, a waste rock pile, or exposed sulfide-rich rock, can cause discoloration and turbidity in receiving waters, and the loading of ions mobilized by the acid can cause a decrease in aquatic flora and fauna, and reduction in the quality of groundwater. The primary cause of acid generation is the oxidation of sulfide minerals, predominantly pyrite and pyrrhotite. Considerable mine tailings are being stored on surface in vast tailings impoundment areas across Canada. In the tailings within this study, from the Sudbury, Ontario area, the sulfide mineral of primary concern with respect to acid generation is pyrrhotite. Different tailings types show varying and progressive degrees of oxidation correlating to their specific sulfur contents. The degree of oxidation is determined by the relative extent to which the sulfides have reacted as well as the depth of oxidation within the tailings. Natural Resources Canada, CanmetMINING is dedicated to research supporting the Green Mining Initiative, a program reducing business risks by demonstrating practices that reduce environmental impacts. In cooperation with the Canada Mining Innovation Council (CMIC), applied research aims to reduce land disturbance, waste volumes, and releases to the environment. By reutilizing tailings from vast impoundment areas as a component in backfill, the potential environmental impact would be lessened considerably, due to the reduced tonnage stored on surface long-term. From an operating perspective, there is a need for supplemental feed for backfill from time to time. The reclamation of old tailings for use in backfill is also driven by the fact that old tailings ponds may not be structurally stable, and it may be more cost effective to remove the tailings than to upgrade the impoundment structure. However it is imperative that these old tailings be fully characterized to determine their suitability for use underground, in order to ensure the long-term integrity of the resulting backfill matrix. A study was conducted to investigate the feasibility of tailings reclamation from old impoundment areas as a significant component in backfill. The materials were first physically and chemically characterized, followed by preparation of samples to determine optimal mix proportions for strength development for both paste and hydraulic fill compliance. It was found that the amount of oxidized tailings included in the backfill material had a profound effect on both the segregation and settling properties of the backfill matrix, as well as the mechanical properties of the samples. The strategies for decision-making, based on the criteria for material characterization, mining plan, and cost effectiveness are discussed.

Aug 1, 2013

By Y. Hayashi, A. Fuwa

To analyze zinc vaporization kinetics of zinc smelting slag in the ISP furnace, reduction reaction rate of zinc oxide from ZnO-FeOx-CaO-SiO2 slag system with CO-CO2-Ar gas mixtures has been measured by a therm o-gravim etric apparatus at various ZnO content, Pco, and temperature. The reduction rate was measured under a chemical reaction control in the initial three minutes where surface zinc content can be assumed constant. Through the reaction rate dependency analysis on ZnO contents, Pco and temperature, discussion has been made on its reaction mechanistic information in terms of rate coefficient, adsorption/desorption mechanism and activation energy.

Jan 1, 2008

By W. R. Richmond, T. S. Li, D. Ilievski

The reactive precipitation of ferrihydrite was studied in a laboratory semi-batch precipitator, where a highly concentrated sodium hydroxide solution was fed into an iron nitrate solution. Instantaneous hydrolysis of iron[III] takes place when the two reagents are mixed generating supersaturation, and leading to immediate precipitation of ferrihydrite via a primary nucleation mechanism then followed by limited crystallite growth to 3 to 7nm. A mathematical model of the semi-batch laboratory precipitator was used to simulate the pH responses during the precipitation of ferrihydrite at different reagent feed rates. The model comprised of interconnected compartments of averaged hydrodynamic conditions, incorporating physically meaningful turbulent mixing time constants. The precipitation process is described by the solute concentration conservation equation incorporating a postulated ferrihydrite primary nucleation model. It was found that the semi-batch precipitator model predicted the experimental pH response reasonably well. The experimental results demonstrated that the reagent feed rate has a critical effect on the course of the precipitation of ferrihydrite, i.e. it is a rate determining step given the fast hydrolysis and precipitation kinetics.

Jan 1, 2005

By Y. Lizotte

"This paper examines the application of blasthole sloping to narrow vein mining in Canada, for ore deposits where widths are less than two metres. While the technique has now been utilized for more than ten years, it remains in the experimental stage and on-site testing is necessary for its adoption at new mining operations or in differ¬ent geological settings. It is intrinsically a safer method than other narrow vein methods in current use.The investigation describes the main operating parameters for mines recently surveyed. The criteria for method applicability are defined and the problems encountered are studied. It is concluded that blasthole sloping for narrow vein mining is a viable modern method which promises to gain popularity and that emerging fragmentation technology and blasting research can be used to further increase applicability of the stoping method."

Jan 1, 1991

By Raj K. Rajamani, Nikhil Dhawan

"Agglomeration has become common pre-treatment step to improve heap leach percolation thereby recovery, the fundamental understanding of the agglomeration process for crushed ores is still lacking. Agglomeration is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing. Numerous experiments have been carried out in laboratory scale batch drums using different ores. It has been found out that experimental agglomerate size distributions exhibit self-preserving spectra. The self-preserving/ similarity distribution of the agglomerates is found to be independent of operating conditions and is uniquely determined by the size enlargement mechanism. An empirical model based on the absolute difference between moisture applied and optimum moisture was developed. This model uses self-preserving spectra in the form of a Rosin-Rammler distribution function to predict size distribution at different operating conditions. The empirical model was considerably easier to work with plant scale agglomeration drums. Also, a test known as dip test is developed which improves fundamental understanding of the agglomerate formation and growth mechanisms. This test also provides the progeny size distribution of each agglomerate size. The progeny size distribution was analyzed with a model that partitions the particles into a host and guest category. The ensuing partition coefficient identifies the behaviour of a particle as a host for other particles or a guest layering on other particles. This concept helps in identifying the type of agglomerate that would result for a specific feed size distribution. INTRODUCTIONHeap leaching is one of the hydrometallurgical processes that have served as a green and economically viable process for the treatment of low grade complex ores of copper, uranium, nickel, silver and gold (Dhawan et al., 2013). Heap leaching appears to be a favorable candidate for the least energy consuming process for low grade ores. In heap leach operations nowadays a pretreatment step known as crushed ore agglomeration has been implemented (Dhawan et al., 2013). A bed of agglomerates improves the uniform percolation of solution through the heaps of ore. Therefore, it was possible to treat wastes and mill tailings via agglomeration and heap leaching. Agglomeration pretreatment is required for ores which either contain excessive amounts of clay or an excessive quantity of fines generated during mining and crushing (Bouffard, 2005; Dhawan et al., 2013).While agglomeration has become common practice pretreatment step in heap leach operations, the fundamental understanding of the crushed ore agglomeration process is still lacking. The author reviewed publications up to 2012 on the crushed ore agglomeration process and did not come up with modeling studies on the topic (Dhawan et al., 2013). Some of the possible reasons can be the stochastic nature of the process, experimental difficulties, and lack of instrumentation for fundamental studies."

Jan 1, 2016

By S. Radacina Rusu

The satellite-based global positioning system (GPS) has significantly changed the way site operations are carried out in surface mining. The GPS has impacted safety, productivity, fleet efficiency, and maintenance practices. However, no comparable global localization system exists for underground mines. This paper discusses recent work in the application of ideas from the mobile robotics research community to the problem of real-time vehicle positioning in underground drift networks. Related previous work recently focused on the creation of globally consistent 2D maps of underground environments that possess sufficient detail to be used for underground localization. Our current work entails the development of a GPS-like system for mobile mining equipment, with results given from both laboratory and field experiments.

May 1, 2011

By J. ?H. Chen

Remote sensing technologies have been applied to numerous fields and already benefited those in improving efficiency and recognition accuracy. Change of streamflow can be devastating to residents living along riversides. Still it is difficult to detect such deathly change in large area scale by traditional field surveys. The research aims at provision of detecting streamflow change using a mathematic method based on remote sensing technologies. The scope is on remote sensing stream images taken during the invasion by Typhoon Morakot, bringing one of the major catastrophes to Taiwan. An algorithm was adopted to deal with streamflow recognition on RGB images. The algorithm is capable of yielding change measured by meters and illustrates how main streams shift. An practical example for the Baolai area surrounded by Laonong stream shows that the streamflow moved 88 meters (36 pixels) toward the downtown area during the invasion by Typhoon Morakot. In addition, the results highlight all dangerous zones (scouring zones) for residents to prevent further potential damage.

Aug 1, 2013

By Lawrence Devon Smith

The Business Case for Sustainable Development ?What are SD & TBL? ?Investment Funds & Fund Managers ?Banks and Risk Aversion ?The Dilemma of Juniors ?Meet Your New Partners ?The Cost of Problems ?The Cost of Delays Sustainable Development ?Humanity has the ability to make development sustainable -to ensure that it meets the needs of the present without compromising the ability of future generations to meet their own needs.? Our Common Future BrundtlandCommission, 1987

May 1, 2003

By Magnus Evertsson, Johannes Quist

HPGRs have since introduced in the 1980s (Kellerwessel, 1993; Schönert, 1988), now become integral comminution units at several minerals processing plants around the world. Even though a lot of the initial issues concerning performance, availability and wear have been addressed and solved there are still phenomena and aspects which can be improved and understood further. Schönert and Sander (2002) presented experimental results and a mechanistic model including the internal force dynamics between the rollers and the compacted bed. They derived expressions for the pressure distribution involving most of the influencing terms and effects. However, in order to solve the differential equations several of the terms vanish by assumptions. The Schönert and Sander model reflects the experimental data in many aspects but the predicted shear force distinctly deviates from the experimental results at the angular position of the peak pressure level. This finding suggests that the particle to particle interaction and breakage process in the different zones seen in Figure 1 are complex and difficult to model using analytical models. A numerical modelling approach using DEM does not require the same amount of assumptions and simplifications of boundary conditions. Hence such modelling may provide further knowledge and vital understanding. In this paper the breakage process is simulated in order to investigate the shear slip behaviour and how it relates to different operating variables. A laboratory scale HPGR corresponding to the experimental setup used by Schönert (2002) have been modelled in EDEM (DEM-Solutions). The bonded particle model (BPM) is used for modelling quartz particles (Potyondy, 2004). The breakage model strength parameters are calibrated against interparticle breakage experiments in an Instron 400RD compression device. The contact model parameters are calibrated using calibration methods developed by Quist (2015). The floating roller dynamics are modelled using a spring-damper system. Results present insights regarding the interparticle slip behaviour as well as the frictional tangential force distribution on the rollers. The simulated roller pressure distribution shows good correspondence with previously reported findings in the literature.

Jan 1, 2016

By J. H. Gray

"IntroductionIn 1980, Fording Coal Limited started conceptual planning studies which led to major changes in the long-range mining plan at their Fording River Operations. These new plans have been completed and are now in operation.To assist personnel in a timely completion of this major revision to the long-range plan, existing in-house drill hole data base and scheduling systems were used and a computerized Mine Modelling and Planning System was purchased. With these tools, plan s were developed which led to completion of initial access to the peak of Eagle Mountain and the start of mining operations in March 1983. As mining area s open up and new geo logical data is obtained, detailed plan s are being extended and revised.With the geology and mine plan s on line, this work can now be done with less effort and plans ca n be adapted to provide flexibility in mining operations. Changes in market conditions can be accommodated by moving mining operations into different seams for different coal types. The computer systems are used to revise pit designs and schedules accordingly."

Jan 1, 1986

By Fathi Habashi

This Historical Metallurgy Note is the final part of a three-part series, the first two of which appeared in the November- December, 1997 and January, 1998 issues of the Bulletin. This series of articles is dedicated to the memory of Nikolai Maximovitch Pereskuryakov (1940- 1994), Rector of Saint Petersburg Mining Institute from 1992 to 1994 who passed away unexpectedly at the age of 54, shortly after celebrating the 275th Anniversary of the Institute.

Feb 1, 1998

By Marko Lampi, Ross Andrews, Jouni Pihlasalo, Robert Matusewicz

With widespread discussion on reducing carbon, sulphur and other emissions, use of sustainable energy sources and the pivotal circular economy theme, consideration needs to be given to pyrometallurgical operations broadly and more specifically, non-ferrous metallurgy. These themes present a number of challenges in terms of current operations and the view of processing the metals which are largely taken for granted in day to day living. This paper considers how these themes will impact pyrometallurgical flowsheets using the non-ferrous base metals as an example. It will examine the flowsheet chain to offer views on the boundaries of flowsheet optimization and the application of available tools to meet these future goals and challenges. INTRODUCTION The themes of reducing footprint through lowered CO2, S and other emissions, together with process sustainability (e.g. lowered energy) and links to the circular economy are well known to everyone in the metals industries. Whether it is reducing greenhouse gas emissions or analysing the importance of metals recycling in the circular economy, all these themes carry with them the fundamental premise of any change being considered; how can you best optimize a system to meet your aims? Of course, this depends on the available tools and the approach used for optimisation.

Jan 1, 2019

By K. Torigoe, S. Owad, C. Tokoro, Y Tsunazawa

The mechanism of an abrasion process to recover metal values by removing components from printed circuit boards (PCBs) is modeled using a discrete element method (DEM) simulation. To simulate the abrasion process, a model PCB geometry was constructed consisting of bonded particulates. The simulation allowed connections between particles to be broken if the bonding force calculated from DEM exceeded a threshold level. Simulation results were compared with experimental comminution data using an agitation mill with test PCBs on which nine capacitors were surface solder-mounted. Simulation results obtained from the DEM with the anchoring model corresponded to experimental observations.

Jan 1, 2011

By G. Song

Magnesium has excellent bio-compatibility in terms of its density, strength, elastic modulus and toxicity. However, due to its poor corrosion performance, so far magnesium has not been successfully used in the human body as a permanent implant material. Nevertheless, there is a possibility to utilize the low corrosion resistance of magnesium to make magnesium into a temporary implant component that can gradually dissolve in the human body after surgical region heals. This will avoid the secondary operation to remove the temporarily implanted component and the chronic inflammatory discomfort caused by the implant. This paper is aimed at exploring the possibility of using magnesium as a degradable bio-material through investigating the corrosion behaviors of pure magnesium and surface treated magnesium in a simulated body fluid (SBF) solution. It was found that magnesium corroded rapidly in the SBF solution, resulting in vigorous hydrogen evolution and a strong alkalization effect. Hence, it is impractical to use magnesium as a permanent implanted material or even a degradable implant. However, a proper anodizing treatment can significantly improve the corrosion resistance of magnesium, and hence slower down the hydrogen evolution and alkalization processes, which will allow to control the corrosion or degradation of magnesium at a desired rate in the human body. With a controllable corrosion rate, it is believed that magnesium as a degradable implanted material will be eventually achievable.

Jan 1, 2006

By Matthew R. Ward

This paper aims to describe the reasons and methods to extend enterprise networks into underground mines. Currently mines use a number of communication networks for telephones, PLCs, two-way VHF radio and computer networking. Each system can have different wiring, protocols, converters and interfaces all which require expansion and maintenance. The convergence of voice, video and data using Ethernet and TCP/IP has the very real benefit of one ?wire? for underground networks. Now that the majority of underground equipment can communicate using TCP/IP, network convergence can offer reduced network expansion and maintenance costs. Cost savings are good, but the truly exciting aspect of network convergence using Ethernet is the low-cost, high speed wireless networking now available . These wireless networks offer an opportunity to facilitate mining automation even on a small budget. How would mine operators change they way they operate if they could gather vehicle location and data in real time? What about controlling equipment remotely? The list of applications is long and includes traffic control, dispatching, real-time ore blending, tele-operation, automated production reporting, vehicle health monitoring, elimination of paper forms and immediate network access for surveyors and geologists. An ideal converged network for underground mining would be robust, inexpensive, easy to expand, enable fast and secure connections while keeping voice communication performance equivalent or better than what is now provided by VHF radio

Apr 1, 2005