Search Documents

By J. F. Wang, Y. Jin, Z. L. Wang

Smelting reduction as an ironmaking technology for the 21st century has been challenging the traditional blast furnace. The process has many attractive advantages over the blast furnace, however, the massive by-produced coal gas mainly containing CO, H2 and CO2 requires further treatment. From a chemical engineering view, coal gas is a valuable chemical stock and can be transformed into hydrogen-rich synthesis gas. Hydrogen can be directly used as clean fuel and synthesis gas can be used for the production of some important chemicals such as methanol, ammonia and dimethyl ether. Among those chemicals, dimethyl ether as an alternative clean fuel for diesel engine and liquefied petroleum gas has been drawing more attention. It has excellent environmentally-benign behaviours not only in compression ignition combustion, but also in the much lower emission of SOx and NOx. In this work, a combined technology of smelt reduction ironmaking and direct synthesis of dimethyl ether, which will strongly promote the energy efficiency, environmental protection and resource recovery, is proposed and described in detail.

Jan 1, 2004

By W. J. D. Stone

"INTRODUCTION Over the past decade, a number of publications have described the advances in High Intensity Wet Magnetic Separation. A number of significant, but small capacity installations were made and are successfully operating. These were followed some three years ago by larger installations treating ilmenite gravity concentrates; at least one machine treating 25 tons per hour of new feed was installed and is successfully operating.However, this still did not result in general acceptance that High Intensity Wet Magnetic Separation could be applied on a large scale. Neither did it dispel the feeling that High Intensity Wet Magnetic Separation was ""expensive"" and hence, confined to small scale – high value applications suchas the cleaning of tin concentrates. In addition, there is the usual reluctance of being the ""guinea pig"" which has resulted in waiting to see ""someone else"" make the first large installation decision. Such a decision and installation has now been made.Therefore, the purpose of this paper is to show that High Intensity Wet Magnetic Separation has been commercially accepted on a large scale and to show its general application to the base metal mineral industry.Examples are confined to a few specifics due to the large volume of preliminary test data that is available. The art has now reached the stage where much of the preliminary work should be taken through to serious evaluation."

Jan 1, 1971

By K. Torigoe, S. Owad, C. Tokoro, Y Tsunazawa

The mechanism of an abrasion process to recover metal values by removing components from printed circuit boards (PCBs) is modeled using a discrete element method (DEM) simulation. To simulate the abrasion process, a model PCB geometry was constructed consisting of bonded particulates. The simulation allowed connections between particles to be broken if the bonding force calculated from DEM exceeded a threshold level. Simulation results were compared with experimental comminution data using an agitation mill with test PCBs on which nine capacitors were surface solder-mounted. Simulation results obtained from the DEM with the anchoring model corresponded to experimental observations.

Jan 1, 2011

By F. Hassani, J. Peck, D. J. Lucifora

The performance of a rotary blasthole drill is heavily dependent on the material being drilled. This material is a microcosm of the in-situ geology that makes up the surface mine in which the rotary blasthole drill is deployed. The performance metrics that are influenced by the in-situ geology are penetration rate (distance drilled per unit time), rotary torque and to a lesser extent rotary speed and vibration. For simulation and testing purposes it is useful to have a validated plant model based upon the application of study. Once validated, a plant model can be used to perform simulation based testing as a supplement and possibly in place of more expensive and logistically complex field testing. Previous studies in the field of rock mechanics have supplied proven models that relate the performance of a rotary blasthole drill to the material being drilled for a given rock type with a given drill bit. In this study, field based experiments were conducted in an active surface mine on a working rotary blasthole drill and the corresponding monitoring while drilling (MWD) data was recorded. Data analysis was then performed on the collected field data. The techniques used successfully fit the collected MWD data to the previously proven rock mechanic models. This paper explores the theory relating rotary blasthole drill performance to the material being drilled, illustrates the required data collection and data analysis techniques, and demonstrates the ability of these techniques and the known rock mechanic models to provide a simulated plant model for the drilling process that can then be validated. This validation is also discussed.

Jan 1, 2015

To determine the optimal circuit configuration for gravity gold recovery consideration should be given to a range of factors in addition to the efficiency of the gravity circuit, including capital costs, ease of operation and impact on comminution. The most common gravity gold circuits utilise a centrifugal concentrator treating a portion of the hydrocyclone underflow. This paper will examine this option and alternative circuit configurations to illustrate the effect of various gravity circuit feed and tailings configurations on the equipment sizing, capital costs, operating costs, water balance, comminution efficiency and gravity gold recovery. The optimum circuit configuration can provide reduced capital and operating costs, maximise gravity gold recovery and improve comminution efficiency.

Jan 1, 2011

By Jan E. Nesset, L. Paul Staples

"High Gradient Magnetic Separation (HGMS) technology, although developed over 2 decades ago, has not been widely applied to the separation of sulphide minerals. Under conditions of strong magnetic field gradients, weakly magnetic minerals such as chalcopyrite (CuFeS2) and marmatite (Zn(Fe)S, sphalerite with iron in solid solution) behave paramagnetically and can be effectively separated from diamagnetic minerals such as galena (PbS). The application of this technology to the separation of Cu-Pb and Zn-Pb bearing streams in the treatment of fine grained complex sulphides may in some cases be more effective than separation by flotation. A 2 TPH Sala HGMS pilot plant was operated at Brunswick for a nine month period, ending in March 1995. The testing demonstrated the mechanical reliability of the technology, the consistency of operating results and the scale up from laboratory testing. HGMS is seen as a complimentary technology to flotation, best suited to performing those separations of galena (and other diamagnetics) which flotation does not do as well.IntroductionBackgroundSince the turn of the century, the magnetic character or magnetic susceptibilities of minerals have been determined with increasing precision and accuracy. Figure 1 illustrates specific magnetic susceptibilities of some common minerals. As long as susceptibility ranges do not overlap, separation is possible.In 1937, the principle of using a magnetizable matrix material in a magnetic field to increase both magnetic flux density gradients and number of capture sites for susceptible minerals was first applied (Frantz). It was not until the 1970's, however, that the genuine development of wet high gradient magnetic separation began with the introduction of very fine matrix materials to the magnetized volume of large solenoid magnets. Today, dozens of HGMS units purify, filter and separate minerals, primarily for the removal of iron stained minerals from clays used in the paper coating and china clay industries and for the recovery of fine titanium and iron oxides in the iron ore industry. Only the Garpenburg mill in Sweden is currently applying a continuous HGMS machine to separate complex sulphide minerals; upgrading a lead concentrate since 1988."

Jan 1, 1996

By J .. R. Dalton

"Blasting in high sulphide content ores presents at least two major safety considerations: (1) compatibility of the explosives with the ore while resident in the borehole; and (2) introduction of a flame and shock producing explosive into this environment, while minimizing the risk of reactive ignition in the chemical reaction products/sulphide dust cloud resulting from the detonation. This paper will discuss only the second consideration, i.e. post detonation reactivity.The ETI (Explosives Technologies International) Technical organization, in consultation with the U.S. Bureau of Mines, reasoned that the most relevant considerations in the development of an explosive for this application are:• minimization of reactive gaseous detonation reaction products;• flame duration reduction;• flame temperature reduction;• increased explosive sensitivity;• reduced probability of ""low order"" detonation; and• maintenance of energy level as high as possible.Obviously, not all of these are totally independent properties, i.e. increased sensitivity will reduce the probability oj low order detonation as will higher energy levels. However, these considerations were examined separately as if they were independent."

Jan 1, 1994

By A. I. A. Salama, M. W. Mikhail

"A comprehensive software package has been developed at the Western Research Centre to meet many of the coal preparation requirements in the Canadian coal industry. This package performs three main functions: (1) data handling and manipulation; (2) data analysis, including the generation of washability data, performance evaluation and prediction, density and size modelling, evaluation of density and size partition characteristics, and attrition curves; and (3) graphics output.The software described in this paper is potentially a valuable tool for coal preparation plant engineers and operators for evaluating process performance and adjusting plant density separator cutpoints. Moreover, the analytical laboratory technician could find this package very useful in manipulating and presenting laboratory results."

Jan 1, 1997

By K. M. Tait, M. M. McDonald

"An overview of the status of the development and application of Integrated Gasification Combined Cycle (IOCC) power generation is presented. Current projects in North America, Europe and Japan are described, together with the status of plans to apply the technology in Canada. A brief review of the technology is presented, including promising coproduction cycles and hybrid gasification fluid bed processes. The ability of the process to be modified for CO2 to be extracted for enhanced oil recovery or disposal is addressed. The environmental impact of IGCC technology is compared to those of other power generation technologies IntroductionDefinition and HistoryIntegrated Gasification Combined Cycle (IGCC) technology is a concept which has been around for about 50 years but has been generating increasing interest in the last 10 to 15 years. This paper focusses on coal as the feedstock for gasification. Other feedstocks used in gasification systems have included oil, biomass, tires and petroleum coke. IGCC technology integrates coal gasification with generation of electricity by means of a combined cycle system which fires the produced gas in the gas turbine. Figure 1 shows the basic components of an IGCC system which are the gasifier, the gas cleanup system and sulphur recovery plant, the gas turbine/generator set, the heat recovery steam generator (HRSG) and the steam turbine/generator set. The benefits of an IGCC system over a conventional Rankine Cycle pulverized coal (RCPC) fired system for the generation of electricity from coal are that the IGCC system has potential to have higher efficiency and lower emissions of NO., SO and CO2 per unit of power produced than the corresponding RCPC system."

Jan 1, 1994

By So-Yeong Lee, Moosang Lee, Seung Hwan Ahn, Ho-Sang Sohn, Jongshin Chang

It is necessary to understand the characteristics, phase changes and chemical reactions of flue dusts introduced from a furnace to an off-gas line in order to achieve the stable operation and the improvement. This study is to develop the dust reaction model for chemical reactions of dusts in an uptake shaft of smelting furnace and a waste heat boiler. Phase equilibria and reaction paths in this system were determined by thermodynamic calculation with experimental and industrial data. The oxidation reaction rate of dusts was determined by the gas film mass transfer controlling. And the sulfation reaction rate was evaluated by the unreacted shrinking core model. Kinetic parameters were estimated by reference data including industrial ones. The present study with the developed model shows various effects of temperatures, dust particle sizes, and O2 gas partial pressures on dust reactions. INTRODUCTION The flue dusts from a copper smelting furnace move along a furnace off-gas stream into an uptake shaft and a waste heat boiler (WHB) and electrostatic precipitator(s). It is necessary to control the dust quality in order to stabilize the operation because the sticking behaviors differ depending on the phase of dusts. Phase changes of dusts are caused by chemical reactions at given conditions such as temperature and partial pressure of gases. Therefore, it is required to understand the phase changes and chemical reactions of dusts in order to perform the improvement and stable operation. The present study carried out the investigation to understand their fundamental knowledge. Especially, this study was focused on the kinetics of chemical reactions of flue dusts, developed the model. In particular, the scope of development and utilization of the model was defined as the uptake shaft of the Mitsubishi S furnace and the S-WHB radiation section in the Onsan smelter. Information needed for the modeling work referred to data from these processes.

Jan 1, 2019

By N. Haghdadi, D. M. Maijer, A. B. Phillion

B206 is a recently-developed high-strength Al-Cu casting alloy with reduced Ti and Fe, as compared to the well-known AA 206 alloy, for improved hot tearing resistance. In the current study, the solidification kinetics of this alloy as a function of cooling rate from 1 to 15 K/min were studied using differential scanning calorimetry (DSC) and microscopy. Specifically, the evolution in fraction solid, grain size, and secondary dendrite arm spacing have been characterized. The DSC results show the occurrence of three peaks during cooling from the liquid state, which are related to the formation of primary aluminum, a pre-eutectic intermetallic, and the eutectic phases. Thermal analysis also indicates that while the liquidus temperature is not sensitive to the cooling rate, the temperatures at which the pre-eutectic and eutectic phases form are strongly coupled to the rate of heat extraction. A decrease in the latter temperatures was observed when the rate of solidification was increased, leading to a lengthening of the freezing range of the primary phase. The results will be useful for improving B206 casting processes, specifically through modification of mould cooling conditions.

Jan 1, 2014

By G. M. Ritcey, M. Silver

"The processing of uranium ores produces tailings that could constitute environmental problems. At most operations the tailings are dumped into a designated area, with the ultimate acid drainage occurring if sulphides are present, together with the release of metal constituents to the rivers and streams. If the chemical reactions occurring within the tailings could be predicted, perhaps methods could be developed to either increase or decrease 'the rates of reaction. One such study has been in progress at CANMET during the past three years. The paper describes the use of Iysimeters containing low-grade and complex uranium tailings to determine the effects and interactions of bacteria, sulphides and solvent extraction organics on the release of radionuclides and on acid production. A simulated rain cycle nine-fold the normal was used and the Iysimeters were subjected to timed intervals of light and darkness. As a result, the tests simulated a 25-year period.IntroductionAlthough Canadians derive major benefits from uranium, there are environmental and health consequences, not yet fully understood, from the associated mining and milling operations. A major project at CANMET (Canada Centre for Mineral and Energ y Technology) has the ultimate goal of ensuring that any adverse effects on man and environment, now or in the future, resulting from the processing of uranium should be acceptably low. The magnitude of the task was exacerbated by the fact that the increased demand for electrical energy and the resultant increased prices for uranium oxide during the 1970s led to a rapid expansion in the industry. Annual world demand for uranium was expected to increase 12-15 fold in the next quarter century, with annual requirements of between 200,000 and 300,000 metric tonnes anticipated by the year 2000. Currently, the demand is low and the prices for the oxide have decreased."

Jan 1, 1982

By Leonardo F. Trivino

Despite the significant economical and safety implications of poor blasting practice in mining and quarrying operations, the default practice in many large operations, including both design and control, is considerably below standard when compared to other engineering disciplines. Blast dynamics includes a number of complex phenomena, such as the generation, propagation and interaction of stress waves, the expansion of high pressure, high temperature gases from the explosive components, and their combined effects upon the rock mass, including fracturing, fragmentation and displacement. In order to tackle this non-trivial problem, a combined finite and discrete element software (Y-code) capable of accounting for the dynamic behaviour of stress waves, simulating fracturing processes and modeling the expansion of gases is under development. The constitutive models used in this particular software are fundamentally simple, however, non-linearity and chaotic behaviour result as natural consequences of the interaction of relatively simple processes and mechanisms, such as propagation of stress waves in the immediate vicinity of the exploding borehole, and the creation and propagation of fractures. Advances on its development and comparisons with experimental data show realistic propagation of stress waves and fracture networks.

May 1, 2013

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By Makarinskym F. M.

"This paper describes mechanical and operating modifications that were and are being made to current on-line flotation cells at Falconbridge Nickel Mines concentrators. Improved metallurgical performance and metal recoveries of some 3·4% over the past ten years are the end result of the modifications made. The paper acknowledges the contribution of operating, technical and maintenance personnel and the Company ""suggestion plan"" program. 1. INTRODUCTIONFalconbrirdge Nickel Mines Limited, incorporated in 1928 is a major product of nickel, copper,coba1t and other metals and minerals. The Canadian Nickel Division operating facilities in the Sudbury Area currently includes seven mines, two concentrators, and a smelter.For many years at all concentrators, improv0mcnts in metal recoveries have been continually under investigation. One area was to improve the flotation cell performance. This paper will deal with mechanical and operating modifications to the cells at the Strathcona and Falconhridge Ni-Cu sulphide concentrators, at the Sudbury Operations.One of the prime means to mineral beneficiation processing has been, and will continue to be, the basic froth flotation cell. The efficient operation of a flotation cell is the key to satisfactory metal selectivity and recovery. The essence of good design is simplicity. Changes to cell design can contribute to a significant improvement in metal recovery.Over the past 10 years, modifications to the flotation cells have contributed to an improvement of some 3-4” in mineral recovery. Providi11g tl1c initiative for improvements include operating, maintenance and technical personnel, as well as the employee suggestions submitted th1·ough the Suggestion Plan Program."

Jan 1, 1982

By S. Yue, P. Vo, M. Jahazi

The flow behaviour and microstructure development of a near-alpha titanium alloy during beta working has been investigated. Typical cogging conditions were simulated through compression testing of IMI834 at temperatures of 1025°C-1100°C, strain rates of 0.01 s-1 - 1 s-1 and post-deformation heat treatments up to 4h. Using a synthesis of available literature models, a finite element model has been developed and validated through quantitative measures of flow stress-strain data and beta grain characteristics. Flow behaviour was analyzed through a self-consistent method while the microstructure development was considered with regard to the kinetics of beta recrystallization. Deformation at beta or high alpha/beta working temperatures (T>l025°C) produced minor flow softening with complete grain refinement achieved through metadynamic recrystallization.

Jan 1, 2006

By Nickvinder Bhath, Johnson Matthey Plc, Jamie Baker, Daniel Kim, Jeff Lucht, Shijie Wang

"Precious metals (PM) in copper anode slimes are traditionally recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of precious metals, including relatively inert metals such as gold and platinum group metals (PGMs). In this paper, a new method to recover PGM from complex and difficult feed streams is described. Using a proprietary Advanced Ion Exchange (AIX) adsorbent which has a high selectivity for PGMs over other metals and can achieve high PGM mass loadings with a series of incredible pilot test data plus the business case generated from the study results are also presented in the paper.INTRODUCTIONPrecious metals in copper anode slimes are traditional recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of many metals, including relatively inert metals such as gold and platinum group metals (PGMs). Fully hydrometallurgical processes for extraction and recovery of gold and silver from copper anode slimes were employed in major copper refineries since 1995, which was first developed at Rio Tinto Kennecott Utah Copper.In Rio Tinto KUC process, the wet chlorination and gold solvent extraction were utilized to enable recovery of gold and silver as well as other metal compounds. The availability of water and the interaction and amenability of gold processing in water-based solution makes it possible that gold and silver are produced in only five days, compared with a traditional pyrometallurgical process that took 45 days. Most copper refineries are still following the tradition, but the use of hydrometallurgical technologies is increasing as the world demand for metals increases, energy utilization, and environmental viability."

Jan 1, 2016

By T. Negeri, M. Boisclair, A. Bouajila

CanmetMINING has been working on process development for separation and concentration of rare earth bearing minerals from various ores. Among others, the flowsheet development for the Montviel Rare Earths/Nb deposit, located at the north end of the Abitibi region in Quebec and owned by GeoMegA Resources Inc. (GeoMegA) is now at an advanced stage. The concentrate produced by a flotation-only process at the early stage of the project accounted for higher than 90% TREO and Nb recovery in 40% mass. This concentrate was submitted to SGS Lakefield for hydrometallurgical processing. Lixiviation of the concentrate using hydrochloric acid yielded approximately 99 % REE. An overall (from ore in ground to final precipitate) REE recovery of 80% was obtained through a series of selective precipitation steps. Recently significant additional developments have been made. CanmetMINING is steadily improving the quality of concentrate produced through a simplified, more efficient flowsheet which consists of flotation, magnetic separation, and a thermal treatment procedure. The paper discusses aspects of the process that allowed obtaining 82% recovery of TREO and Nb in 16% of mass, the best result to-date.

Jan 1, 2014

By A. J. Hyett, R. D. Reichert

"A laboratory and field research program was conducted to investigate the major factors influencing bond capacity of grouted cable bolts. The results indicate that cable bolt capacity most critically depends on the grout uniaxial compressive strength (UCS), the radial confinement, and the embedment length.In the laboratory &apos;split-pipe&apos; tests were conducted using P VC, aluminum and steel pipes to provide radial confinement, and field test sites were chosen in granite, limestone and shale rock masses. For both datasets higher capacities were obtained under conditions of higher radial confinement. A correlation between the two was obtained through a comparison of the radial wall stiffness of the laboratory pipes with that of the field boreholes as measured using a high pressure dilatometer. Cable bolt capacity was found to increase with embedment length though not in direct proportionality.The use of low water cement ratio grouts (<0.40) can increase cable bolt capacities by 50% to 75%. This effect is maximized under conditions of high radial confinement. However, the use of super thick grout paste (0.30 and less) may be both impractical and undesirable, first because of their limited pumpability and second because of their inconsistency in strength. Grouts with a water cement ratio of between 0.35 and 0.40 are recommended for practical cable bolt applications."

Jan 1, 1992

By Jeonghwan Kim

Intelligent Excavation System (IES) has been considered to be one of the desirable solutions to improve the productivity, quality and safety of the current earthwork processes. IES is composed of various hardware and software modules including task planner (work command generator), local and global work environment sensors, GPS and other sensors to acquire the excavator?s status, robotic controller and electronic valves, and the manipulator (excavator). A data communication manager was required to coordinate the signal or data-flow in between these modules considering the operational status of IES such as; excavation start/completion, truck detection, terrain model update, emergency stop, local sensing, GPS/motion sensor data handling, and so on. This paper presents the role and functions of this data communication manager. After every possible operational status of IES operation was identified, a protocol of each communication process in the form of string-type was made. The components of IES are connected with either wired or wireless network. Therefore, they can communicate with the manager using socket (TCP/IP) communication. The data communication manager is also capable of accessing a web-based project management information system, which constantly updates the performance of excavation robot to online database.

Aug 1, 2013