Search Documents

By J. L. Christie

A recent case of failure of a-low karat gold alloy by stress-corrosion cracking is of interest because it illustrates a principle frequently overlooked: the relation between high residual stress and high yield point. The alloy contained Gold, per cent 39.6 Copper, per cent 51.1 Silver, per cent 5.2 Nickel. per cent 3. 1 Zinc, per cent 1.0 Tension tests on the alloy showed the following:

Jan 1, 1945

By Benjamin F. Tillson

The hammer drill rightly receives the credit for having made the one-man drill possible, and so many economies seem possible through the proper application of different types of hammer drills to various mining, quarrying, and excavating operations, that an indication of the 'economies effected by the New Jersey Zinc Co. at its Franklin mines may be of pertinent interest. When this company commenced its trials of hammer drills in 1907, these tools had not been developed to one-fourth the capacity and refinement which they have at present. At that time it was frequently stated that such a small tool, drilling holes of less diameter than the reciprocating rock drill, could not drill enough holes in a shift to permit the placing of sufficient explosive to break a tonnage of ore comparable with that produced by the "rock drills;" that the placing of small holes inclined upward, at angles steeper than 40' above the horizontal, could not be expected to produce results equal to the large flat, wet or dry, holes in the breasted back of an overhand stope, and would only shatter the ground so as to make the back unsafe. In spite of these adverse opinions, the hammer drills first showed their superiority over both heavy and light reciprocating drills in raising and in stoping, and then in drifting and quarry work. As a result, all of the reciprocating drills at the Franklin mines were scrapped three years ago, all of the mining work being accomplished with increased efficiency, as shown in detail in this article. With the advent of the hammer drill in this property, it was considered advisable to make comparative tests of all the tools accessible, and it has since been the policy to investigate the merits of any advance of the drilling art in order to get the maximum amount of work from the tools. The necessity of devising some means of standardizing drill tests, and of measuring the consumption of compressed air as well as the drilling speed, was early realized. The common test was to fill a measured air receiver with compressed air at a certain gauge pressure, run the drill until the pressure had dropped to too low a figure, then compute from the time, drop in pressure, and

Jan 1, 1915

Photographs of Officers

Jan 1, 1923

By James C. Fulton

Since publication of the First Edition of "Basic Open Hearth Steelmaking," in 1944, this book has been a major reference on the subject of steelmaking. The Second Edition of 1951 was so fundamental that it has retained its general usefulness to the present date. However, recently some of the material has been updated in connection with the writing of a companion book, "Electric Furnace Steelmaking." The sponsor of these two books, the Physical Chemistry of Steelmaking Committee, has felt that the new material should be made equally available to purchasers of either book. Accordingly the subject matter of Chapters 14, 15, and 16 of this new edition is duplicated by corresponding chapters in "Electric Furnace Steelmaking." It was also recognized that the use of oxygen in the open hearth and in the new basic oxygen processes represents a major development that should not be omitted from any basic reference. Thus the major new feature of this Third Edition is the supplement on "Oxygen in Steelmaking." The cooperation of the Iron and Steel Division's Acid Converter and Basic Oxygen Steel Committee (now merged to form the National Open Hearth and Basic Oxygen Steel Committee) is specifically recognized. In addition to the authors of chapters listed elsewhere, it should be noted that Arthur B. Wilder was the Committee Chairman. Although the changes in the Third Edition are important, the Committee cannot overlook the classic character of the Second Edition. This edition was edited by W. O. Philbrook and M. B. Bever in collaboration with H. B. Emerick and B. M. Larsen. It is anticipated that the Third Edition will maintain the value of the book until the current rapid changes in all basic steelmaking processes stabilize themselves sufficiently to justify a complete revision of the entire text in Part I. The experienced service of Wesley Burr in incorporating the new material in the index is also recognized.

Jan 1, 1964

By Mason K. Banks

A process has been developed which produces spodumene concentrates assaying 6.0 pct Li20 and 0.45 pct Fe203, with 70 to 75 pct recovery of spodumene. Two flotation separations are required: the simultaneous removal of mica, feldspar, and quartz as a froth product using a cationic collector, and the subsequent removal of iron-bearing minerals as a froth product while spodumene is depressed as a tailing.

Jan 2, 1953

Frank Clemes Smith, Deadwood, 8. D. (communication to the Secretary): The reading of Mr. Chance's interesting paper suggests a few ideas relative to his discussion of certain Black Hills gold-ores. Mr. Chance refers to his examination, in 1897, of " the (Carboniferous) limestone plateau-country which encircles the central area of the Black Hills," and says that " it had been generally assumed that the mineralization of this formation was confined to the northern area;" further, that he "found, however, a general mineralization, extending in zones or belts throughout the region," and that the ores, being more or less specially

Jan 1, 1900

MISSOURI SCHOOL OF MINES The Missouri Mining Association has enjoyed a very good year. Last October the society was reorganized and the following officers elected for the year: E. Ross HOUSHOLDER, President, ORE N. MANESS, Vice-president, WILLIAM REBER. Secretary, RUAL CHAVEZ, Treasurer. The head of our mining department, Prof. C. E. Forbes, is now serving as a Major in the United States. Army. We were fortunate in having. Prof. Chas. E. Locke, of Boston, with us for part of the winter to take charge of the senior mining work. During the autumn and winter months we had a number of informal smoker lectures in Norwood Hall. Among the speakers at these meetings were: H. A. Buehler, Missouri State Geologist; Chas. E. Locke, Boston, Mass.; V. H. Hughes, Tulsa, Okla.; Dorsey Lyon, Washington; D. C.; Prof. G. H. Cox, Professor of Geology, Rolla, Mo.; together with a number of returned alumni.

Jan 8, 1918

Sec. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whom residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the claw of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1944

By E. Hein, R. A. Dodd

The fatigue softening of prior strain-hardened poly crystalline copper has been determined by measuring changes inflow stress resulting from fatigue treatments. Tensile fatigue does not soften the metal, while the softening due to reversed stress fatigue depends on the extent to which fully reversed stressing is approached. True tensile fatigue is shown to be possible only in the case of long wire specimens. Annealing following fatiguing of strain-hardened metal shows that tensile fatigue is very effective in modifying normal recovery and recrys-tallization. OBSERVATIONS by Ludwik and Scheu,' Kenyon,' Polakowski and Palchoudhuri, Kemsley, and Broom and Ham,596 have shown beyond doubt that strain-hardened metals are softened by reversed-stress fatigue. To some extent the softening might be associated with a rearrangement of dislocations, but the results of Broom and Ham5 on the temperature dependency of the fatigue hardening of annealed copper, and those of McCammon and Rosenberg7 on the partial recovery at 100'C of fatigue-hardened copper suggest that point defects may be involved. Since lattice vacancies are the only species of point defect present in appreciable quantities in thermody-namic equilibrium, most attention has been accorded them in the various theories advanced to explain hardening and softening effects resulting from fatigue. Precise mechanisms remain uncertain, and while some effects may be due to single vacancies, defects arising from vacancy clusters may also contribute to the changes in properties. All types of plastic deformation result in point-defect formation, one frequently invoked formation mechanism involving the nonconservative motion of jogs formed by the intersection of, for example, mixed dislocations. But since fatigue deformation is thought to be a particularly effective way of forming point defects, additional mechanisms peculiar to fatigue must be sought. One possibility is that jogged loops contract during the unloading cycle to give rows of vacancies. A local high-vacancy concentration could conceivably promote polygonization and recovery by climb, and, therefore, could explain the fatigue softening of strain-hardened metals under appropriate conditions of temperature. Conversely, the experiments by Broom and Ham6 on the fatigue hardening of copper single crystals involving subsequent tensile testing of previously fatigued specimens, resulted in the observation of distinctly lowered yield points. This could be due to vacancy atmospheres associated with dislocations, possibly augmented by jogs on dislocations. In addition to the yield-point phenomenon, a post-yield hardening was observed, with a temperature-dependence resembling the friction-hardening of irradiated metals,9 this again suggesting a point-defect mechanism. An important development in this field has been the observation,10 by transmission electron microscopy, of high concentrations of prismatic loops in fatigued aluminum. By analogy with quenched aluminum filmso11 it seems certain that these loops originate in the collapse of vacancy clusters formed during deformation. Metals, such as copper, having a relatively low-stacking fault energy would tend to produce Frank sessile loops (in practice tetrahedral defects with stacking faults on all (111) planes) rather than the glissile prismatic loops observed in aluminum. The manner in which these various defects affect the different aspects of fatigue behavior has not yet been fully investigated. The present work was designed principally to indicate whether tensile fatigue gives rise to hardening and softening effects similar to those associated with reversed stress fatigue, and with the hope of providing additional information on the contribution of point defects to fatigue deformation. Despite the uncertain ty often associated with the interpretation of resistivity data, i.e., the relative contribution of stacking faults and other defects, such measurements are conveniently employed to study point defect pheno-

Jan 1, 1962

By R. F. Mehl, C. E. Birchenall

R. E. Hoffman and D. Turnbull—The authors have presented evidence which they have interpreted as indicating that the rate of self diffusion is not intrinsically more rapid at grain boundaries than within the grain. Grain-size effects which apparently exist are attributed rather to impurities concentrated at the grain boundaries. In view of our own experiments and the existing evidence, we believe that the support for this hypothesis is not convincing. We have in progress an investigation in which the rate of self diffusion of silver is being measured over an extended temperature range in both single-crystal and polycrystalline specimens. The results of the single-crystal experiments and some preliminary data on fine-grained polycrystalline specimens have already been reported:' and it is anticipated that a complete report will be published in the near future. The self-diffusion coefficient of large-grained polycrystalline silver (1 grain per sq mm) has previously been measured by Johnson" between 730" and 940°C. The diffusion coefficients which we have measured in single crystals (210 plane normal to diffusion direction) agree within experimental error with values calculated from an extrapolation of Johnson's curve down to temperatures as low as 500 °C. However, it has been demonstrated that the overall self-diffusion rate in fine-grained polycrystalline specimens (initial grain size of 0.003 cm) becomes measurably larger than the overall rate in a single crystal at a temperature of 600°C, and the discrepancy between the two rates becomes greater as the temperature is further decreased. In fact, it has been possible to obtain satisfactory penetration curves for polycrystalline specimens using the sectioning technique at temperatures as low as 400°C. At this temperature, the penetration is 50 to 100 times greater in the polycrystalline specimens than in a single crystal. Fisher" has developed an analysis whereby the ratio of the rate of the unit diffusion process at the grain boundary to the corresponding rate within the grain can be calculated from the penetration curves and an assumption as to the width of a grain boundary. This analysis applied to our data indicates that the unit process at the grain boundary is faster by a factor of 10' at 475°C when the grain boundary width is taken to be 5. The silver used in most of these experiments was obtained from the Handy and Harmon Co. and listed as 99.97 pct pure. Preliminary experiments on 99.999 pct silver from the Jarrel-Asch Co. indicate a grain-size effect of the same order of magnitude as in the less pure silver. Nominally, these purities are as good, at least, as that of the carbonyl iron used by the authors, but of course if an impurity effect does exist its magnitude might be very dependent upon the nature of both major and minor constituents. The authors have cited the work of other investigators who have found no grain-size effects. Neither Steigman, Shockley and Nix" nor Maier and Nelson8 were able to correlate self-diffusion coefficients of copper with grain size. However, all their measurements were performed at or above 750°C; and on the basis of our work with silver, no grain-size effect would be expected at temperatures above about 0.7 of the absolute melting temperature unless the grain size were exceedingly small. Likewise, in the investigation of the self diffusion of lead by Seith and Keil,14 the lowest temperature at which the diffusion coefficient was measured in polycrystalline specimens was 207°C, which is still sufficiently high so that the lack of a grain-size effect is not surprising. Finally, in those experiments on iron from which they concluded that there was no grain size effect, Drs. Birchenall and Mehl seem to have no information as to the actual grain sizes immediately prior to and following the diffusion anneal. Without this information, we believe that their own experiments offer little support for their hypothesis. F. S. Buffington, I. D. Bakalar, and M. Cohen—The results given in this paper agree in order of magnitude with those tentatively reported by us.27 However, significant differences exist in the two sets of data, and it may be well to make an explicit comparison. The diffusion studies at M.I.T. were conducted on somewhat higher purity iron (99.98 pct Fe) than the grades used by the authors, but this is undoubtedly not the answer. Fig. 4 shows the diffusion results of both laboratories for the gamma phase, omitting the authors' data on the commercial steels, while fig. 5 presents a similar comparison for the alpha phase. The divergence is much more marked in the latter case than in the former. In connection with the M.I.T. determinations, all of the runs in the gamma range and those above 800 °C in the alpha range were conducted with specimens having a relatively thick (0.002 cm) electrodeposit of radioactive iron. This practice minimizes any possible error due to extraneous diffusion that may occur during the heating to and cooling from the operating temperature. An exact solution of Fick's law for these boundary conditions was used in calculating the diffusion coefficients. At a later time, three runs were made below 800°C, using very thin electrodeposits similar to those of the authors, and the points fell considerably below the values expected from the extrapolation of the results based on the specimens with the thick deposits (compare dash-dot line in fig. 5). However, in the runs with the thin deposits, deviations of 100 pct were found between the individual specimens, whereas the maximum deviation with the thick deposits was less than 25 pct. Accordingly, it is not known at the moment whether the M.I.T. points below 800 °C should be given as much weight as those above 800°C. If this were done, the frequency factor would be of the order of 400 cm2 per sec, which is quite high. In other metals, the frequency factor for self diffusion lies between about 0.1 and 10 cm2 per sec. As the points below

Jan 1, 1951

Jan 1, 1892

Arizona E. P. MATHEWSON, Chairman W. V. DECAMP. First Vice-chairman H. W. ALDRICH, Second Vice-chairman E. D. GARDNER, Secretary-Treasurer, Care U. S. Bureau of Mines, Tucson, Ariz. F A. AYES, J. P. HODGSON W L DU MOULIN WILLIAM KOERNER Boston Meets first Monday each winter month GEORGE B WATERHOUSE, Chairman GEORGE A PACKARD, Vice-chairman F. LEROY FOSTER, Secretary-Treasurer Room 8-219, Mass. Inst. of Tech , Cambridge, Mass. F K MORRIS F S MULOCK

Jan 1, 1923

By R. A. Bergman, C. J. B. Fincham

THERMODYNAMIC properties of many high-temperature systems containing sulfur, such as slags, metal sulfides, and solutions of sulfur in liquid metals, have been studied by means of equilibration with known gas mixtures.'" This method presupposes a complete and accurate knowledge of the thermodynamic data for all possible components of the gas phase at high temperatures. However, a survey of the data available up to 1952 on the thermodynamics of gaseous sulfur species and compounds, by Richardson and Jeffes,' showed that there was considerable uncertainty in the values of the free energies of formation of S, SO, HS, and CS. In many cases, this uncertainty made it impossible to decide whether or not these species would form a significant proportion of the sulfur present in the gas phase in any given system. After the review by Richardson and Jeffes had been published, St. Pierre and Chipman6 measured, by an indirect method, the free energy of formation of SO. This also enabled a clear choice to be made among the three possible spectroscopic values for the dissociation energy of S2 into atoms10 thereby determining the free energy of formation of S from S2, and fixing the free energy of formation of HS more accurately" The main purpose of the present investigation was to measure the free energy of formation of CS, which was still in considerable doubt. For example, at 1600°C, it could be estimated to be +6 +25 kcal per mole,* most of the uncertainty being in the * Based on the dissociation energles of CS6 and S2,5 the heat of sublimation of graphite, and, the assumption that the entropy of formation of CS is the same as that of CO. value of the dissociation energy." A secondary purpose of the investigation was to determine more accurately the equilibrium sulfur pressures over dilute solutions of sulfur in carbon-saturated liquid iron. General Method Dilute solutions of sulfur in liquid iron, saturated with carbon, were brought to equilibrium at 1600" and 1800°C, with known gas mixtures consisting, initially, of A and CS2. After equilibrium had been reached, the melts were quenched and analyzed for sulfur. In the high temperature region of the furnace, an equilibrium was set up between the various possible sulfur species and compounds in the gas phase; namely, CS2, CS, S2, and S. (It can be calculated that the amounts of S6 and S, are negligible at these temperatures:) Morris and Bueh17 and Kitchener, Bockris, and Libermana had previously studied the corresponding

Jan 1, 1958

By B. M. Larsen

Jan 1, 1965

AIME 1953 DIRECTORY SUPPLEMENT OFFICERS AND COMMITTEES OF LOCAL SECTION; COUNCIL OF SECTION DELEGATES Linwood Thiessen, Chairman H. D. Vaughan, Vice-Chairman John H. Melvin, Secretary EXECUTIVE COMMITTEE L. E. Thelin, Connecticut J. B. Cunningham, Arizona W. L. Penick, San Francisco G. L. Yates, Kansas DELEGATES Adirondack - C. DeWitt Smith '54 Alaska - Robert 11. Chapman, ?54 Arizona J. B. Cunningham, '53 Black Hills - Sidney M. Runke, '54 Boston -R'. Schuhmann, Jr. ?54 Carlsbad Potash - W. P. Wilson, '54 Central Appalachian - Charles T. Holland, '54 Chicago - H. A. White, '54 Cleveland - Milton Tilley, '54 Colorado - J. Paul Harrison '54 Columbia - Harold Kirkemo, '54 Connecticut - Lewis E. Thelin, ?53 Dallas - Kenneth F. Anderson, '54 Delta - Roy S. Sullins '54 Detroit - F. P. Bens, '53 East Texas - Joseph A. Morris, '54 El Paso Metals - E. M. Thomas, '54 Florida - W. O. McClintock '54 Fort Worth - Ray Elner, '51 Gulf Coast - H. E. Treichler, '53 Kansas - G. L. Yates, '53 Lehigh Valley - H. R. Gault '54 Lima, Peru - R. P. Koenig, ?54 Lou-Ark - A. H. Crawford. '53 Mexico - W. G. Kane, '54 Mid-Continent - J. H. Beesley, '53 Minnesota - J. R. Stuart, '54 Montana - F. W. Strandberg, '53 Nevada - Albert Silver,'53 New York - P. Malozemoff, '54 North Pacific - A. H. Mellish, '54 North Texas - K. F. Anderson, '54 Chio Valley - J. H. Melvin, ?53 Oklahoma City - Charles Miller, '53 Oregon - T. C. Matthews, '54 Penn. Anthracite - D. C. Helms, '54

Jan 1, 1953

By R. A. Swalin, A. H. Geisler

THIS study represents an investigation of the effect of annealing temperature on the texture of drawn molybdenum, iron, and an iron alloy containing 14 pct Al. The effect of temperature on annealing textures has not been widely investigated in the past. One of the obstacles in making such a study using usual X-ray diffraction techniques results from the

Jan 1, 1957

By David S. Cahn

Pilot-plant and laboratory tests were made on blends of steel plant flue dust and portland cement to determine whether the flue dust could be pelletized for use as a source of iron in dry process cement manufacture. Strength and setting time results showed that an acceptable agglomerate can be made with a Type II portland cement binder. Abrasion-resistant and well-sized pellets were made in a horizontal drum, using a simulated closed circuit, with a binder content of 7.5% and a moisture content below 15%. Pellet quality was found to be relatively insensitive to changes in binder concentration above 5%. Simulations of stockpiling and weathering indicate that little difficulty would be encountered with use of the flue dust pellets in cement plants.

Jan 1, 1972

By Coolbaugh, Franklin

CRUSHING of Climax mine-run ore is carried out in two plants: No. 1 plant (flowsheet in Fig. 1) has a capacity of approximately 5000 tons per day. It is used as a stand-by except when maximum production is required. No. 2 plant (Fig. 2) has a top capacity of approximately 17,000 tons per day. The No. 2 crusher is more efficient to operate on reduced tonnages regardless of the wide variation in peak capacities. The system of crushing is similar in both plants: Mine ore, of a size which can be drawn through 48 by 96-in. slusher openings underground, is dumped into the crusher bins from ten-ton mine cars and fed into 48 by 60-in. Buchanan jaw crushers by means of chutes and Ross chain feeders. The jaw crushers are set to discharge at approximately 9-in. size. Jaw crusher discharge is conveyed to 7-ft. Symons standard cone crushers where it is broken to minus-2-in. size,

Jan 1, 1946

By C. S. Roberts

Microstructural studies of a Mg-10.3 pct Al alloy showed that discontinuous precipitation during aging multiplies the grain boundary area available for easy deformation in elevated temperature creep. An increase of strain rate for a 6.2 pct Al alloy at 400°F, where precipitation and creep are concurrent, caused an increase in the volume percentage discontinuously precipitated at the completion of the process. The relatively poor elevated temperature creep resistance of heat treated alloys of the Mg-AI-Zn type was explained in these structural terms. C resistance of the heat treatable Mg-A1 based alloys is poor compared to that of Mg-Ce based alloys. While the latter show a continuous precipitate, Mg-A1 alloys prefer a discontinuous precipitate at grain boundaries. '.:' It has been concluded that the excellent creep resistance of Mg-Ce alloys was primarily due to the continuous precipitation which especially localized at the grain boundaries.' The purpose of the present investigation was to obtain a parallel correlation, if such exists, between the poor creep resistance and the state of precipitation in Mg-A1 alloys. Discontinuous precipitation produces about three times as many true grain boundaries as originally existed. This microstructure would be expected to have a marked influence in creep, where quantity of grain boundary area is important. Experimental Procedure The two experimental alloys contained 6.2 and 10.3 pct Al. They were made from electrolytic magnesium by alloying under flux and casting in 3 in. diam permanent molds. The ingots were extruded into 1 1/4 x 1/8 in. flat stock under the following conditions: billet preheat 700°F (2 hr), container and die temperature 700°F, speed 3 fpm, and area reduction ratio 45:1. The creep specimens were machined from blanks which had been solution heat treated 24 hr at 770°F and aged 16 hr at 400°F. Attempts were made to control the grain size as closely as possible for extruded stock. The grain size after solution heat treatment was about two thousandths of an inch for the 6.2 and five thousandths for the 10.3 pct Al alloy.

Jan 1, 1957

By V. Rajaram, I. P. Nielsen, H. D. Raymond

The Parachute Creek member of the Green River formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch joint venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 12, 1979