Search Documents

By E. Douglas, V. M. Malhotra

"This report presents the results of a laboratory study undertaken to evaluate ground granulated blast-furnace slag from Algoma Steel Corporation, as a replacement for Portland cement in cemented mine backfill. The evaluation was based on the results of compressive strength tests performed on cylinders cast from mixtures made with a granulated blast-furnace slag and tailings from four different mines in the Sudbury basin. Various percent¬ages of slags and various binder to tailings ratios were used.Tests results show that, in terms of compressive strength, the slag performs as well or better than Portland cement as the binding agent in cemented mine backfill. Lime was found to be a poten¬tially good activator for ground granulated slag in mine backfill applications.A field test was conducted at one of the mines, consisting of placing a mixture of 95.5% ground granulated slag and 0.5% lime into a stope, and inspecting the floor slab as it hardened. The slag performed as expected, considering the backfill mixture proportions used and the preparation of the test site."

Jan 1, 1989

By P. J. Mehrfert

"Recovery of mineralized coarse particles is notoriously low in conventional concentrators that treat copper porphyry ores. The application of coarse particle flotation techniques has the potential to achieve comparable metallurgical performance at significantly coarser primary grind sizings. ALS Metallurgy has been conducting both internal research and commercial test programs to investigate the potential of Eriez HydroFloatTM technology on copper sulphide ores. Test data indicates that significant improvements in the recovery of copper sulphide bearing particles between 200µm to 850µm can be achieved using Hydrofloat technology compared to conventional flotation techniques. This paper summarizes the results from a selection of test programs that includes recovery by size data from both conventional flotation and HydroFloatTM tests. An explanation of the apparatus and test procedure will be given. Mineralogical analyses of the test products and characteristics that limit metallurgical performance will be discussed.Description of Apparatus and Test ProtocolThe HydroFloatTM laboratory cell is a clear plastic column with an internal diameter of 14 cm. Water and air are introduced to the cell through a circular manifold located in the lower portion of the cell. The cell has a conical bottom which directs slurry to a pinch valve that controls the discharge of tailings. Feed solids are introduced to the upper portion of the cell in slurry form. The cell is operated in a manner such that the manifold water creates a teeter bed zone of suspended solids in the middle portion of the cell. Tailings exit the bottom of the cell at a high pulp density, and most of the introduced water overflows the top of the column and is collected in a launder. Particles with a hydrophobic surface may attach to air bubbles that percolate through the teeter bed, rendering them sufficiently buoyant to be transported to the overflow launder.Three significant features of this arrangement enhance the potential to recover coarse, low grade particles by flotation techniques. Firstly, the hindered settling conditions created by the rising column of water allow coarse particles to become buoyant once attached to a modest sized air bubble. Secondly, the flow conditions within the cell are relatively quiescent compared to a conventional flotation cell that utilizes an agitator. This allows particles that have limited hydrophobic portions of their surface, due to a low content of exposed sulphide mineral, to maintain a somewhat fragile attachment to air bubbles long enough for successful recovery to the overflow. Finally, the absence of a froth phase at the top of the cell allows particles attached to air bubbles to immediately exit the vessel, reducing the potential to drop back into the pulp phase as bubbles burst or coalesce."

Jan 1, 2017

By Nick D. Rose

The importance of structural geology in open pit slope stability is overlooked in many mining operations due to pressures to cut costs and minimize mine personnel. As a result, mine geology staff are often unable to keep up with geological mapping of the pit slopes due to other day to day production oriented tasks. In some instances, key structural controls that contribute to slope instability may not be identified until after a slope instability has initiated, at which time it may be difficult or impossible to delineate these features in the field. Even for small slopes, understanding the engineering and structural geology of the rock mass, as well as the effects of groundwater and blasting practices, are of key importance to slope stability. Two case histories are presented as examples of mining operations that experienced slope instability with little more than anecdotal information about the structural and groundwater conditions encountered during mining. By conducting field reconnaissance, simple slope stability analyses and ongoing slope monitoring, practical remedial measures were implemented, allowing continued safe mining operation.

May 1, 2002

By Matthew A. Baumann

Tooth-wear on mining shovels requires continuous monitoring. Worn teeth impede excavation performance, increase energy usage, and increase the risk of lost or broken teeth and adapters. A machine-vision-based automated tooth-wear monitoring system is presented. The system employs a rugged boom or stick-mounted camera to capture images of the shovel teeth. An onboard computer processes the images in real-time to determine the length of each tooth. The current wear state is available via a network-accessible log for on-demand status updates. By continuously recording tooth length changes over time, the logs can be used to estimate wear rates and patterns, permitting comparisons between different G.E.T. configurations, operator behaviour patterns, or material types. This detailed, quantitative data permits site-specific optimizations to wear packages and maintenance scheduling. Automating wear monitoring offers the crucial wear information necessary to minimize maintenance costs and reduce unscheduled downtime. A 37-day field trial in a copper-gold mine demonstrated the ability of the system to measure tooth lengths, compute wear rates, and detect differences in tooth wear based on their position on the bucket.

Nov 1, 2011

By A. C. Wilson

In 1991, local prospector C. ?Mickey? Clement recovered at least three alluvial diamonds from the Michipicoten River. Two of these stones were sent to the Department of Mineralogy, Royal Ontario Museum, where they were identified as industrial grade diamonds with weights of 1.05 and 1.13 carats. Both stones were described as frosted and graphite-inclusion riddled. In 1995, prospector Sandor Surmacz and geologist Marcelle Hauseux discovered diamonds in bedrock approximately 20 km north of the Michipicoten River. An 18.1-kg bulk sample of a xenolith-rich lamprophyre, taken from an outcrop at the side of the Trans Canada Highway north of Wawa, yielded 1 macro diamond and 5 micro diamonds. All but one was gem quality (Sage 2000). Since then, more than 36 occurrences of diamonds in bedrock have been reported in an approximately 30 km2 area centred 20 km north of the town of Wawa. The occurrences are hosted within a sequence of unusual, Archean-aged, heterolithic breccias previously considered to have no economic significance. Ten kimberlite occurrences also have been confirmed in the Michipicoten greenstone belt in the last 5 years. Two of these kimberlites are diamondiferous. To date, expenditures on property acquisition and diamond exploration in the Wawa are estimated at $120 million (CAN). This paper summarizes the geological observations made on these occurrences and discusses including the relationship between the occurrences and the regional geology.

May 1, 2003

"Increasing demand for timely and accurate information about flotation plant performance requires metal accountants to increase the scope and reporting frequency of plant production. This trend has brought in-process inventory estimation at the forefront of metal accounting issues. Such significant in-process inventories can be locked in diverse process equipment (bins, holding tanks, flotation cells, thickeners, pipeline, etc.) or in stockpiles (ore, concentrates, tailings, etc.). Practice has shown that boldly ignoring these in-process inventories or the errors associated with their estimation lead to unreliable metal balances thereby creating confusion in plant production planning and operational performance assessment. To this extent, the characteristics (physical bounds, spatial heterogeneity and residence time) as well as the available measurements (volume, density, humidity, mass, composition, etc.) of each unit/section found in a generic flotation plant are jointly reviewed with respect to the particular metal accounting issues they present. The daily and monthly metal accounting tasks are then reviewed together with possible methods for obtaining reliable inventory estimates including different procedures for end-of month reconciliation.INTRODUCTION Most of the cost reduction initiatives of the mining industry aim at improving capital efficiency and asset utilization. Among the possible paths through which these goals can be achieved are mine-to-metal optimization, real-time plantwide process control (Hodouin, 2011) and knowledge sharing databases (Bascur & Linares, 2006). However, the successful implementation and subsequent monitoring will ineluctably results in an increased demand for timely and accurate information. This more than often requires metal accountants to increase the scope and reporting frequency of plant metal production. A striking example of such scope expansion is the Minas-Rio iron ore project in Brazil (Anglo American, 2013) having a pipeline route of 525 km between the concentrator and the concentrate shipping area. Several other mining companies have also set an increased frequency for their key performance indicators thereby shrinking the metal accounting period from monthly to weekly and daily. Those concurrent trends have brought in-process inventory estimation at the forefront of metal accounting issues. Indeed, as illustrated in Figure 1, improving trading reactivity requires improvements in production planning which strongly impacts the requirements for reliable metallurgical accounting. Furthermore, practice has shown that boldly ignoring significant in-process inventories or the errors associated with their estimation can lead to unreliable metal balances. In other words, since metal balances are the cornerstones of metal accounting, some of the risks associated with important business decisions are linked to errors associated with in-process inventory measurements."

Jan 1, 2014

By Jean Rosaire

?GWIOP Location ?Climate and Physiography ?History ?Geology ?Deposit Types ?Mineralization ?Historical Mineral Resources ?Conclusions and Work Program

May 1, 2007

By M. Pourkani, M. Karga, Samid Banis, Andre Laplante, G. Langari-Zadeh

"The Sarcheshmeh mine processes 40,000 t/d of ore grading 0.9% Cu and 0.035% Mo. Grinding is effected in single stage ball mills using 80 mm forged steel balls, with an average consumption of 850 g/t. One of its 5 m diameter, 8 m length ball mills was emptied to measure the ball size distribution. The broken balls were first separated from the total charge, and the remaining balls classified into five size intervals of +7O mm, -70 +60 mm, -60+50 mm, -50+40 mm, -40 mm.The charge was composed of 280,534 balls (excluding broken balls) with a total mass of 305,180 kg. It was found that 4.0 % of the balls were broken; the size distribution of the charge was also markedly different from the desired one, in particular for the small-sized balls. For instance, 9% of the balls were expected to measure 2.54 to 3.18 cm in diameter, but none was found. On the other hand, the amount of top size balls was 30% higher than expected. The radial hardness of balls, which was determined by cutting the balls in halves, showed that the hardness sharply drops when the balls become smaller than 65 mm. The unexpected ball size distribution was attributed to the rapid change in the balls radial hardness. Based on the measured ball size distribution, a new ball make-up charge which uses 80% of 80 mm and 20% of 60 mm balls instead of 100% of 80 mm was proposed and implemented. The effect of the new ball make-up procedure in terms of ball consumption and grinding efficiency is being investigated."

Jan 1, 1999

By J. E. Udd

"In early 2000, CANMET-MMSL was engaged by the Ontario Ministry of Labour (OMOL) to conduct an international study of the practices, in several key mining jurisdictions, of determining the criteria that are used to decide when the wire ropes used in mine hoisting are to be retired from service. Subsequently, the author visited key officials and institutions in Canada, the United States, the Republic of South Africa, the United Kingdom, Germany, and Poland. Material from the Australian province of New South Wales and Hungary was also included.The report that resulted included, among other sections: (1) the history of wire ropes and trends in manufacturing technology; (2) a review of mine hoisting practices; (3) the requirements regarding safety factors; (4) a review of the various operations and their potential future development; (5) the criteria for rope replacement; (6) potential future developments that could take place in both hoisting and rope inspection practices in Canada; and (7) recommendations.Subsequently, the report was issued by OMOL, and as a CD-ROM by CANMETMMSL. In this paper the author presents the key findings and the recommendations made in the study."

Jan 1, 2004

By P. Scinto, A. Festa

"Orway Mineral Consultants Ltd (OMC) as a consultancy has specialized in comminution circuit design for over 30 years. The OMC Power Model is OMC’s in-house software for specific grinding energy power-based circuit calculations. The model uses ore hardness parameters from testwork, circuit configuration, equipment geometry and operating conditions as inputs. The model combines proprietary and published power models to predict the total specific energy and the specific energy for each of the components of the comminution circuit. This makes the software a valuable tool for the design and validation of JKSimMet modelling or actual plant performance. Proprietary calculations have been developed and reconciled with over 100 plant benchmark projects encompassing a variety of comminution circuit configurations.This paper describes the OMC approach for determining power requirements for the design of grinding circuits. The accuracy of the OMC Power Model software is confirmed through plant survey benchmark performance and comparisons are made with other power modelling techniques. Practical examples are presented, showing applications for single stage SAG (SS-SAG), SAB and SABC circuit configurations.IntroductionConventional low throughput grinding options, consisting of multi-stage crushing followed by rod and ball mills, have almost become obsolete in the move to higher milling rates required to process lower metal grades. Grinding circuits with fully autogenous (AG) or semi-autogenous (SAG) mills, often combined with ball mills are now the standard to meet the high capacity requirement for processing ores with lower metal grades. Simulation software and power-based equation methodologies have been established for designing AG/SAG based grinding circuits and predicting their energy requirements.Presently, power-based equations remain the principal method for designers to size mills and estimate the power requirement for comminution circuits. The technique is simple and it relies on the design to specify a feed and product size plus a hardness index to produce a specific energy value (kWh/t). The desired throughput of the mill is multiplied by the specific energy to give the mill power requirement, which is used in turn to size a mill for dimensions, internal geometry and loading conditions to match the power draw."

Jan 1, 2015

By John G. Payne

The Pebble deposit contains three contiguous zones. In the Pebble West zone, granodiorite stocks intrude gently warped volcanosedimentary rocks that had been intruded by diorite sills and two felsic intrusion breccias. In the Central zone, volcanosedimentary rocks are cut by diorite and granodiorite sills; the latter are genetically associated with the granodiorite stocks. In these zones, widespread potassic alteration consists of brown biotite and K-feldspar, with abundant quartz-carbonate-sulphide vein stockworks. Chalcopyrite/pyrite ratios range from 2/1 to 1/20. Diorite hosts the highest-grade mineralization, with much of it being disseminated. Patchy, later phyllic alteration is moderate and commonly depleted in copper. The Pebble East zone occupies a granodiorite stock and intruded host rocks below an eastwardly thickening wedge of barren Tertiary volcanic and sedimentary rocks up to 600 m thick. Brown biotite alteration and copper mineralization are strong, with chalcopyrite/pyrite ratios commonly over 1/1. The zone extends to a depth of at least 1200 m below surface; some drill holes bottomed in strong mineralization. Later, weak to moderate sericitic alteration removed some chalcopyrite and locally remobilized gold. The Pebble deposit has a Measured/Indicated resource of 3 billion tonnes grading 0.28% Cu, 0.32 g/t Au and 0.015% Mo (= 0.5% copper-equivalent) and an Inferred resource of 1.13 billion tonnes grading 0.30 g/t Au, 0.27% Cu and 0.015% Mo (0.55% copper-equivalent). The Pebble East zone has an Inferred resource of 2.13 billion tonnes grading 0.55% Cu, 0.34 g/t Au, and 0.037% Mo (0.97% copper-equivalent). The Pebble East zone is open to the east and to a lesser extent to the north, south, and to depth.

May 1, 2006

"The application of telerobotics to mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa, and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place, a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run?A Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University to investigate these questions and many more through a series of experiments in a telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian College’s eDome. The laboratory supports many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments, and some preliminary results."

Jan 1, 2005

By Claude MacDonald, John H. Ashburn

"IntroductionIndustrial growth and technological change over recent years had been accompanied by two major sources of concern to management and employees: (a) increase in occupational injury and illness and the resultant costs involved; and (b) equipment damage and breakdowns in concentrated production lines causing more extensive loss potential.Due to economic factors, management attention has focussed more on production and quality than on safety, health and related loss potential sources. As a result , occupational safety and health activism has grown, government legislation of compensation and occupational safety and health standards have progressively developed and stronger liability attitudes have been taken by courts of law.To improve efficiency and allow development in more competitive markets, rising labour costs, equipment costs and safety related financial losses have dictated that attention be given to conservation of all resources. Conservation of resources, people, equipment, material and environment, can no longer be addressed in isolation but must be managed integrally with production and quality. To this end, systems have developed utilizing sound management principles applied with equal intensity to production, quality and loss potential"

Jan 1, 1987

Strategic Branding ? In 2006 Explore for More was created ? By industry, for industry ? Cohesive approach to career attraction ? Defines industry and employers of choice Career Kits ? Positive impression of mining: ? before seeing the brochure 31% ? after seeing the brochure 83% ? Likely to consider a career in mining: ? before seeing the brochure 12% ? after seeing the brochure 23% MARS ? Mining Attraction, Recruitment, and Retention Strategy (2007-2010) ? Attract, recruit and retain a skilled workforce ? Increase participation of under-represented groups ? Dispel myths and misconceptions of the mining industry ? Inform and educate Canadians of career opportunities ? Promote and build upon industry best practices in workforce planning

May 1, 2009

By S. Chung

Mining in highly stressed ground conditions has been an increasing challenge at the Brunswick mine. Over the past 30 years, two large regional pillars were established on the 1000 m Level to support the ground for safe extraction of the surrounding ore. The South Regional Pillar contains about 5 Mt of ore and the North Regional Pillar has about 3 Mt of ore. In the fall of 2000, mining activities were suspended following a series of ground movements around the South Regional Pillar along weak geological structures. After extensive geotechnical investigations, a decision was made to carry out a mass de-stress blast in the West Ore Zone (WOZ) to cut the principal stress across an area of 135 m along strike and 86 m high. At the end of July 2001, the WOZ mass blast was successfully initiated. Following this success, the mine decided to take a similar approach to de-stressing the North Regional Pillar (NRP). The final mass blast was taken in early February 2003. Advanced blasting technologies, including state-of-the-art electronic detonators and blast simulation, played an important role in achieving the successful blasts. The high precision of delay timing and long delay duration of the electronic detonators ensured accurate and reliable initiations of over 800 blastholes in the WOZ mass blast. Orica’s DMC_Blast (Distinct Motion Code) simulation code was used to study different blasting blocks for the desired timing in the initiation sequence. This paper describes the process of applying electronic detonators in complex blasts, and discusses how blast simulation results were interpreted to guide engineering design of the mass blasts.

Jan 1, 2005

By James Scott

Outline Deposit Overview and Brief History ?Geologic Setting ?Local Geology ?Petrography ?Geochemistry ?Mineralization ?Geochronology ?Conclusions Deposit Overview ?Porphyry Cu-Mo-Au ?Discovered 1957 (BIK Syndicate) ?Various programs, most significant: ?Hecla(1970s) ?Teck(Late 1970s Early 1980s) ?Copper Fox Metals (2005 -Ongoing ?optioned from TeckComincoin 2002) ?Measured and Indicated Resources: ?847Mt grading: ?0.292% Cu ?0.019% Mo ?0.202g/t Au ?1.796g/t Ag ?Total ~ 0.485 % Cu Eq.

May 1, 2006

By Ertugrul Alp

Alp & Associates - Who We Are ?? Canadian consulting company (1999-?) ?? Principal Consultant: Dr. Ertugrul Alp, P.Eng. ?? Over twenty-five years experience serving the chemical, mining, pulp & paper, energy, steel, and transportation industries, and government clients. ?? Ph.D. in Mechanical Engineering, University of Waterloo ?? Experience: ?? Westinghouse Canada, Atomic Power Division, Manager, Analysis and Modelling ?? Concord Environmental (later Bovar Environmental), Principal, Manager, Air Quality and Risk Assessment ?? Arthur D. Little, Associate Director, Safety & Risk Practice Leader in Canada ?? Member: NATO CCMS Pilot Project on Disaster Preparedness (1991-1993) ?? Chair: MIACC Risk Assessment Expert Committee, 1995-1999 ?? Member: MIACC Committees on Land Use Planning and Pipelines (1993-1998) ?? Member: CSA/Q850 Risk Management Standard Technical Committee ?? Member: CSA/Z1002 OHS Risk Assessment Standard Technical Committee ?? Member: CCPA/CSChE Process Safety Management Committee (1999-?) ?? Member: ISO-31000 Risk Management Standard Canadian Advisory Committee ?? Chair: CSChE Process Safety Management Committee (2005-2006) ?? Chair: CSChE Expert Committee on Risk Assessment (1999-2005) ?? CSChE 2007 Process Safety Management Award

May 1, 2008

By E. M. Shemang, C. E. Suh, L. Mbinkar, University of Yaounde

"Two iron deposits within the Precambrian mineral belt of Cameroon are described in detail for the first time: the Archean Metzimevin replacement iron deposit enclosed in Fe-enriched itabirite, and the Proterozoic granite-hosted, shear zone-related Mayo Binka magnetite deposit. In the Metzimevin de¬posit, quartz is corroded and microplaty hematite overprints martite-textured hematite. The Mayo Binka massive magnetite veins show evidence of deformation in magnetite (fracturing and microbrecciation) and in overgrowths of specular hematite (mechanical twinning and undulating extinction). The magnetite is partially replaced by hematite (martitization) and goethite. Ores from both deposits have >88% total Fe2O3 and low contents of contaminants such as SiO2, Al2O3, MgO, CaO, P2O5, and TiO2. They are also poor in Cu, Pb, Zn, V, Cr, and Ni. The Metzimevin massive hematite is characterized by an accentuated light rare earth element depletion relative to the Fe-enriched itabirite. It is suggested that the Metzimevin iron deposit is the result of hypogene leaching of gangue minerals from, and further hematitization of, an itabirite protore. Although the genesis of the Mayo Binka massive magnetite is unclear, it is spatially related to Neoproterozoic granitic rocks. The data allow some comparison of these little known, but pot¬entially economic iron deposits, with some of the world’s better investigated deposits, and are useful to the exploration efforts for iron ore currently underway in Cameroon and the Central African subregion.Deux gisements de fer de la ceinture minérale Précambrienne du Cameroun sont ici décrits en détail pour la première fois : le gisement de fer Archéen de Metzimevin formé par remplacement et encaissé par des itabirites enrichies en Fe, et le gisement de magnétite Protérozoïque de Mayo Binka as¬socié au cisaillement dans un granite. Au gisement de Metzimevin, le quartz est corrodé et de l’hématite en microplaquettes se développe au dépends de l’hématite a texture martitique. Les veines de magné¬tite massive de Mayo Binka présentent des évidences de déformation dans la magnétite (fracturation et microbréchification) et dans les surcroissances d’hématite spéculaire (Macles tectoniques et extinction ondulante). La magnétite est partiellement remplacée par l’hématite (martitisation) et par la goethite. Le minerai des deux gisements contient >88% de Fe2O3 total et un faible contenu en contaminants tels que SiO2, Al2O3, MgO, CaO, P2O5, et TiO2. Il est également pauvre en Cu, en Pb, en Zn, en V, en Cr et en Ni. L’hématite massive de Metzimevin est caractérisée par un appauvrissement relatif en terres rares légères relativement à l’itabirite enrichie en Fe. Il est suggéré que le gisement de fer de Metzimevin résulte du les¬sivage hypogène des minéraux de la gangue ainsi que de l’hématitisation poussée d’une préconcentration de fer dans l’itabirite. Bien que la genèse de la magnétite massive de Mayo Binka demeure obscure, elle est spatialement associée aux roches granitiques Néoprotérozoiques. Ces données permettent de comparer ces gisements de fer peu connus et potentiellement économiques avec certains des gisements mondiale¬ment mieux connus, aidant ainsi les efforts d’exploration présentement en cours en Afrique de l’ouest et au Cameroun."

Jan 1, 2008

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016

By Donald J. Hallbom

"While pipeline hydrotransport is often the most economical way to transport large volumes of mineral concentrate, tailings, or fine ore slurry over long distances, it is in mountainous terrain that pipelining becomes particularly attractive. These areas are often remote, with limited existing infrastructure and few potential users willing to share in the cost of new infrastructure. The rugged terrain makes the construction of railways or roads suitable for haul trucks difficult and expensive. The elevation difference between the mine and the terminal means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. As a result, numerous pipelines have been built, or are being considered, in mountainous regions around the world including: Tasmania, New Guinea, China, Madagascar, the Rockies of North America, and the Andes of South America. However, there are technical difficulties that need to be overcome in the design and operation of mountain pipelines that do not affect pipelines on more level terrain. This presentation reviews some of these difficulties and methods used to overcome them.INTRODUCTIONPipeline transport of solid-liquid slurry (“hydrotransport”) is an important and cost-effective means of transporting large volumes of solids over long distances, especially from a single supplier to a single user (e.g., a concentrator to a port, a concentrator to a tailings dam, or a coal mine to a power plant). Pipelines are generally found to be more economically attractive than alternate transportation methods (e.g. trucking, rail, conveyors, shipping, or some combination) over the life of a project (Aude et al. 1974).Hydrotransport systems have been built in a variety of terrains, but it is in mountainous regions that pipelining becomes particularly attractive. These regions are often remote and generally do not have existing transportation infrastructure (roads, railways, navigable rivers). There are few potential users (e.g., farmers, other mines, forestry companies, etc.) who may be willing to share in the cost of new infrastructure. The rugged terrain makes the construction and maintenance of railways or all weather roads suitable for large haul trucks difficult and expensive. Mines tend to be higher than the receiving terminal (e.g. a port). This means that the empty trains or haul trucks need to return up-hill, resulting in high fuel costs. With pipelines, this elevation difference may reduce or even eliminate the need for pumping. Pipelines are easier to construct than roads and railroads in these areas for several reasons, including:"

Jan 1, 2006