Search Documents

By F. Morgan, L. L. Gray, D. W. Reed

A flowMeter has been developed at Gulf Research and Development Co. and tested in the field for measuring the flow of gas in well bores. It has been used in a study of the injection capacity of different horizons in gas injection wells in Oklahoma. The flow sensitive element of the meter is a semi-conductor having a very high temperature coefficient of resistance. Advantages possessed by this meter are the result of that property and the high specific resistance of the element. The instrument possesses a sensitivity considerably higher than any reported previously. In the application described here the element is heated to a temperature considerably above ambient by an electric current, which is supplied by a voltage source at the surface. When fluid flows through the meter the rate of dissipation of heat is increased and the temperature of the element decreases. Because of the negative temperature characteristics of the resistance element such a decrease of temperature will be accompanied by an increase of resistance which, under flow conditions ordinarily found in wells, is of such a magnitude that it can be directly measured or recorded in terms of a change in voltage at the surface. In practice, rate of flow is measured in terms of the drop in voltage in the resistance element. All the metering and control apparatus remains at the surface while the thermal element is lowered into the well on a single conductor cable, consisting of an insulated wire and sheath. The meter is calibrated by passing known quantities of gas through it either at the surface or in the hole at a point immediately above the region in which gas is lost to the formation. In case calibration is made at the surface, the ambient temperature in the hole may readily be obtained by a second resistance element which is operated at a current so low that effectively no heating occurs. The instrument has been adapted to con-tinuous recording, but the velocity of the meter relative to that of the gas must be low unless corrections are made. Curves giving data obtained in actual field tests are shown' The meter can also be used to determine the distribution of flow capacity in a gas producing well. A differential form of the meter has been designed and built in which the local flow or injection capacity of the formation is obtained directly. Introduction When fluid is injected into a well in a secondary recovery or pressure-maintenance operation the question of its most effective use invariably arises. Although the core log, when available, will show the regions of good permeability and oil saturation, there is normally no assurance that the fluid actually enters the formation in zones where injection is deemed desirable. In view of the uncertainties involved in such programs, it is generally conceded that measurements of permeability for a formation in place are more significant than those obtained by the core-sampling technique. A subsurface meter has been developed at the Gulf Research and Development Co. for measuring flow of fluids at different horizons in a well bore, and field tests have been made on the instrument in Cooperation with the Tulsa Division of the Gulf Oil Corp. In this paper the meter is de-

Jan 1, 1948

By G. W. Healy, L. F. Sander

was investigated by reacting thin discs of calcium oxide with gas mixtures of CO2, CO, and Son. Its value was 19,300 * 300 cal independent of temperature in this range. No solid solubility of sulfur in calcium oxide was detected within the limits of the experimental method and it is estimated to be below 0.025 pct by weight. The importance of lime in desulfurization is well-established but complete information on the pure phase equilibrium: CaO + 1/2 s2 = CaS + +02 [11 is not yet available. The goal of this work was to evaluate solid solubility of CaS in CaO and to determine the free-energy change associated with Reaction [I] at temperatures of 1400" to 1650°C. The equilibrium constant for Reaction [1] can be written: It is convenient to rewrite Eq. [2] in the form: where A = {Ps /PqJ1'2 has been referred to' as the "sulfurizing power' of a gas mixture. In this work, thin discs of CaO were suspended in a vertical tube furnace and exposed to CO + CO2 + SOz gas mixtures having known values of A. The samples were then analyzed for sulfur. As expected, X-ray diffraction confirmed that CaS was the only sulfur-bearing phase formed at the relatively low oxygen pressures used. EXPERIMENTAL PROCEDURE Reagent-grade CaCO3 was pressed in a 3/8-in.-diam pill die and prefired in air to produce CaO discs weighing between 0.004 and 0.01 g. Several discs were used to provide a suitable weight for chemical analysis while maintaining a large surface area to react with gas mixtures. These were placed in a platinum mesh basket and suspended in the gas stream in the hot zone of a vertical tube furnace. Desired gas mixtures were prepared from cp grade CO and CO2 and anhydrous grade SO2. The method of soap bubble displacement was used to calibrate capillary flow meters. While this gave excellent results with CO and Con, some problems with bubble insta- bility and soap film "drag" arose with the use of SO2 at low flow rates. Hence, frequent sampling and analysis of gas mixtures was carried out to insure proper control of the ingoing SOZ. The furnace used for gas:solid equilibration was a vertical mullite tube externally wound with 60 pct Pt-40 pct Rh wire having a diameter of 0.028 in. An inner tube of $ in. ID served as the reaction chamber having Pyrex ground joints sealed to the mullite to provide gas-tight connections at top and bottom. A Pt-Pt 10 pct Rh thermocouple was inserted into a protection tube adjacent to the sample basket to measure sample temperature during a run. Constant-temperature control to 2C was observed at any desired set point within the range of this investigation. This was accomplished by a control thermocouple imbedded in the furnace windings which served to actuate an electronic controller wired for high-low operation. The sulfur analyses of the solid samples were carried out using a stoichiometric combustion technique based on the method of Fincham and Richardson. Some analyses were done using a modified evolution method3 but these were used primarily to check the results of the combustion method. The results were in good agreement but the combustion technique of-ferred an advantage in economy of time and material. CALCULATION OF GAS EQUILIBRIA Heating a given mixture of CO + CO + SO2 to high temperatures gives rise to a large number of product species. The details of calculating the partial pressures of these products of interaction and dissociation can be found in several references4,5 and need not be repeated here. The thermodynamic data selected for the major species in the gas mixtures are shown in Table I. Equilibrium constants from these reactions were combined with oxygen, carbon, and sulfur balances and a computer program written to facilitate the calculations. Some early difficulties in reproducing experimental results were finally traced to the effect of atmospheric pressure changes. No reference to consideration of this question had been found in the

Jan 1, 1969

By M. G. Driessen

For a number of years the cyclone, familiar to Americans as a dust collector, has been used as a thickener of suspensions at one of the coal-preparation plants of the Netherland State Mines in Limburg. The plant treats nut-size coal at 120 tons an hour in a heavy-medium washer. The diluted medium from the rinsing screens is thickened in cyclones. More recently the cyclone has been adapted to act as a coal cleaner. The principle of the cyclone thickener is the same as that of the cyclones used in industry for catching dust or fine particles suspended in the air or in gases. Generally the latter are more efficient in this respect—the smallest particles that can be caught with reasonable efficiency are considerably smaller than with the cyclone thickeners. The reason is obvious; the ratio of specific gravities between the dust particles in a gas and the gas itself is about 800 times larger than the ratio between, for instance, the specific gravities of shale particles and water. The ratio of the velocities of fall of shale particles (? = 2.5)† in air and in water is as follows: In the range of Stokes: ?air = 93?water In the range of Allen: Wair = 49Wwater In the range of Newton-Rittinger: ?air = 36.6?water The same ratios apply for the velocities in the centrifugal field, from which it follows that it is especially difficult to catch the very fine suspension particles in a liquid. The efficiency of a cyclone thickener depends mainly on the circumferential velocity of the liquid at its innermost radius, because here the centrifugal forces are the highest. However, these velocities cannot easily be calculated, as the flow is three-dimensional, and thus the axial components cannot be neglected .(p. 252, condition 3). We believe that at first a spiral tangential motion along the cyclone wall is created, which causes the inner vortex ascending from the apex of the cyclone (Fig I). At the same time the inner vortex is strengthened by the individual vortices in horizontal planes, and thus a part of the total flow can find another and perhaps quicker way to the outlet. In any case, the exact motion, not only of the fluid but especially of the suspended particles, is so difficult that we have to refer to the experiments to find the exact behavior of this kind of apparatus. Method of Judging PerforMance of Coal Washer Geologists, rather than mechanical en-gineers, would be able to describe the separating or stratifying effect in nature, but even a bather on the shore lying on the soft sand near the sea wonders why all the small sand grains have approximately the same size. A child playing on the border of the river could easily

Jan 1, 1949

By B. R. Berger

The Getchell area in the northern Osgood Range, Humboldt County, Nevada, was first prospected in the late 1800s for silver, copper, and gold; the first recorded mention of mining activity concerned a silver discovery. The September 17, 1874 edition of the Winnemucca Silver State notes that the Crystal Mining District was newly organized in the Fremont Range (as the Osgood Range was then called) to include discoveries of silver, lead, and antimony made on the Louisa claim. The name Crystal was derived from the plentiful quartz crystals found in-cavities near the prospects. This same area, occurring on the northwestern margin of the Osgood granodiorite stock, was later mined as the Richmond tungsten property, and crystals may still be found there in cavities in a massive garnet tactite. By 1878, how-ever, the name Crystal had been abandoned in favor of Potosi. The next flurry of activity in the Osgood Range was reported in 1899 when a copper strike on Granite Creek in the southern portion of the range received attention. The copper occukences were in a granite contact zone on the southeastern edge of the Osgood stock and, in 1916, the first tungsten in the district was discovered in the same deposit. During the last part of the nineteenth century, cattle and sheep were brought into the Kelly Creek Valley east of the Osgood Mountains by various ranchers. Alphonso and Adrian Bernard were among these ranchers, and in the first decade of the twentieth century, one of them recognized the altered rock where the Getchell Center it is now located. A 3-m (10-ft) deep prospect pit was dug on the outcrop, but the highest assay ran about $11/t ($10 per st). No further work was done on the gold-bearing rock. In 1934, Emmet Chase of Battle Mountain and Ed Knight of Golconda prospected in the area of the Bernard prospect pit and located several lode claims. At this time, Noble H. Getchell, a state senator, was looking for new mining opportunities to develop. He held interests in the Gold Circle Consolidated at Midas, which was becoming a losing venture. Chase and Knight brought their discovery to his attention, and he grubstaked them to prospect further in the area. In need of financial backing, Getchell solicited the help of George Wingfield, Sr., who held a minor interest in the Gold Circle. Wingfield was a successful banker and mine operator during the heyday of Tonopah and Goldfield, and he had become good friends with Henry C. Frick and Bernard Baruch. Wingfield let Baruch in on several very successful mining ventures in Goldfield, and Baruch returned the favor by underwriting the financing of the Getchell mine. Eleanor Roosevelt and Jack Dempsey were early stockholders in the Getchell operation. George Wingfield brought his brother-in-law, Roy A. Hardy, a consulting engineer who had constructed the American Flat mill near Virginia City, to look at the property. Upon inspecting the Chase-Knight claims, Hardy declared the whole area to be mineralized. A crosscut was driven to check the extent of the ore, and the results were better than anticipated. The locators were reportedly given $50,000 for the claims. The Getchell Mine, Inc., was organized on November 5, 1936. A small railroad that ran from Battle Mountain to Austin was purchased, and the ties and rails were moved to Getchell to be used in underground exploration. Enough reserves were found in the Center and South pit areas to construct a 40 t/d (44 stpd) mill. The financial and engineering help for the mill was provided by the Newmont Mining Co. for a 17 1/2% interest in the corporation. Newmont set about trying to solve the metallurgical problems with the sulfide ore, and also directed the early development work. Newmont wanted to grind the sulfide ore underground and oxidize it in the atmosphere by spreading salt on it. Detrital Flat in Arizona was purchased to provide salt for

Jan 1, 1985

By C. W. Thompson

The two-way belt conveyor for coal mine service simultaneously carries coal from faces and transports men and supplies into the mine, largely eliminating the necessity for rubber-tired supply and man haulage equipment and the necessity of maintaining additional headings. SINCE 1920 use of belt conveyor transportation has increased steadily, and capacity in tons per hour per unit has increased at about the same ratio. Belt conveyor systems for simultaneous two-way material transportation have been widely discussed, but heretofore have proved impractical for specific operations. Studies of a proposed means of disposing of wash-ery waste on the return trip of a main haulage conveyor, as yet uninstalled, led to the application of two-way belt haulage to Weirton's underground supply and mantrip problems. Except for a single-tracked main haulage entry, Weirton mine is essentially a full-belt haulage operation with attendant problems of supply and man-trip haulage that could not be handled with conventional belt conveyors during the regular work shift. It was necessary, therefore, to maintain rubber-tired haulage equipment and haulageways serving multiple-shift continuous operations. The conventional underground belt conveyor is primarily intended to transport coal from working faces to surface. Belts are usually reversed to haul men to face areas at the start of the working shift or to transport supplies. The two-way belt conveyor for coal mine service is not yet offered for sale as a unit by any manufacturer and must be built on order. This conveyor, with return run traveling parallel but opposite in direction to the outgoing or coal haulage run, permits not only haulage of coal from faces, but simultaneously permits transportation of men and supplies into the mine at any time, see Figs. 1 and 2. This eliminates, to a great extent, the necessity for rubber-tired supply and man haulage equipment and the maintenance of additional headings. Unlike conventional installations the return belt is in the open for inspection and maintenance. It is less subject to edge wear, since it runs on regular troughing idlers, see Fig. 3. The only points where the edge of the belt can rub are at the drive unit and the tail units where improved design should eventually eliminate edge wear entirely. Individual conveyor sections are lighter, since all that is needed is a tubular stringer on each side to carry troughing idlers only, no cover plates being necessary. The return run is carried on an assembly identical to that carrying the coal haulage run. These assemblies are definitely easier to handle and are cheaper than installations for the same length of conventional belt conveyor. The four pipes required for the complete conveyor frame may serve only as supports, or, with proper couplings, may be used for mine water discharge line, pressure line for face spraying, telephone cable conduit, or any other purpose requiring a pipe line, see Fig. 4. Additional expense, if any, for the increased number of pulleys needed to turn the belt over for the return service is more than offset by reduced expense for rubber-tired supply and mantrip haulage. The two-way belt haulage system is confined to a single heading on intake air, isolated from all other headings by stoppings on each side, and open for air circulation only at the main haulage way and at the faces. One additional heading, also on intake air, is maintained as an emergency rubber-tired haulage way, all other headings being center-posted and used as airways only until retreat work begins. This method, of course, can and should be used with any belt conveyor, since it provides two independent intake airways for escape in case of fire on the belt or elsewhere. Belt heading is heavily timbered even under good top conditions and space between the two runs permits center posting for the full length

Jan 1, 1954

By E. S. Machlin

THE function of this paper is to present certain results based on the fact that the strain energy arising from the solution of out-of-size solute atoms into the solid matrix is free energy and not internal energy, and that this strain energy is almost wholly shear strain energy as Zener1 pointed out. One natural consequence of this fact is an expression for the excess entropy of mixing due to the strain energy. Also, a derivation of the integral molar free energy of mixing partitioned to strain energy will be made using the model of Lawson2 and thermodynamics. This derivation has the advantage of showing in a simple way the assumptions involved in Lawson's treatment. The excess entropy of mixing partitioned to strain energy can be derived in two ways. The first way makes use of the fact that the strain energy is almost wholly in the form of shear strain energy. In this case, as Zener1 pointed out, the change in entropy due to the addition of shear strain energy is to a first approximation given by ?S/?? p,T = - ?lnµ/?T p,? Hence, the excess entropy of mixing partitioned to strain energy will be given by Sx ? = ?S/?? p,T Gx ? = - ?lnµ/?T p,? Gx ? where, Gx ? is the relative integral molar free en- ergy partitioned to strain energy; S is the entropy; is the shear strain energy; µ is the shear modulus; T is the absolute temperature; p is the pressure; and ? is the shear strain. Zener,1 as well as others, has pointed out that the shear strain energy stored in a compressible isotropic solid due to the insertion of an off-size incompres-sible sphere into a spherical hole in the solid, is approximately given by 2/3 µ/O (O°I - O)2 where a is the volume of spherical hole and no , is the volume of sphere. If we now consider the introduction of one mol of such spheres into an infinite volume of solid, then the relative partial molar free energy excess due to strain energy alone is GM ? = 2/3 µ/v (v ° 1 - v)2 where v is the molar volume of solvent and v°1, is the molar volume of pure solute type 1. Let us consider that these spheres are the two types of atoms in a binary solution, then there will be a similar relation for solute 2. The total relative integral molar free energy excess due to strain is then, to the approximations stated above GM ? = GM ? x1 + GM2 ? x2 = 2/3 µ/v [(v ° 1 - v)2 x1 + (v ° 1 - v)2 x2]. Lawson's relation for the strain energy can be de-

Jan 1, 1955

By Lester C. Uren

Tars paper reviews the industrial trends and changes in educational concepts that have led to the development of the modern petroleum engineering curriculum. A trend toward emphasis on engineering fundamentals is noted. While most universities are committed to the traditional four-year engineering program, it is agreed that more than four years is necessary for academic preparation of the petroleum engineer in all phases of his profession. The author proposes a coordinated program of undergraduate and graduate training that will permit of adherence to the general pattern of the present four-year engineering course, with provision for extension of the program into specialized graduate courses of professional character. In the latter, emphasis may vary with the interests and objectives of the individual student. A specific undergraduate curriculum is proposed in which upward of 80 per cent of the available time is devoted to engineering fundamentals. A broad survey of the professional field is afforded in courses grouped in the third and fourth undergraduate years, but detailed treatment of the professional aspects of petroleum engineering is reserved for the graduate program. INTRODUCTION Of necessity, engineering curricula must ever be changing to reflect the new techniques, the changing concepts that are presented as the engineering industries develop and unfold. Particularly is this true of the younger engineering curricula representing comparatively new and rapidly changing industries such as the petroleum industry. Institutions that planned their petroleum engineering curricula a decade or two ago now find that the petroleum industry has become vastly more technical in its requirements. En¬tirely new methods and techniques have come into vogue and must be given place in the curriculum, and some of these are of a character that demands changing emphasis in the fundamental preparatory subjects. College and university faculties cannot complacently assume that curricula in this field that were considered appropriate 10 or 20 years ago still reflect the needs of the industry that they are designed to serve. If they do, their graduates will be poorly equipped to meet the requirements imposed upon them by a rapidly changing industry. Perhaps it is not too much to expect academic authorities to anticipate the trends of industry and equip their graduates with what they will need to attain leadership 10 or 20 years after graduation. Whether or not this desirable objective is possible, there is no excuse for allowing curricula to fall behind the current needs of industry. DURATION OF CURRICULUM The majority of our engineering schools and colleges still adhere to the four-year curricula and there appears to be a definite sentiment among many engineers engaged in industry that work should be so planned that the engineering student may secure the essential academic preparation for his profession in a terminal four-year program. Yet, in recent years, it has become increasingly apparent that four years of

Jan 1, 1941

By Philip D. Wilson

WHEN the United Nations win the war and the decision has been made to control future armament in the Axis countries, plans for the extent and operation of such control must have been prepared, to be ready to put into immediate execution. Such control to be effective must be premised upon complete military occupation of the two countries for a substantial period, with an arrangement at the end of such occupation for continued supervision of these industries into an indefinite future.

Jan 1, 1944

By R. A. Young

Zinc metal production in the operating plants in the United States during 1948 was approximately equal to that of the year 1947, although new developments during the year assure higher output in 1949, if economic conditions are favorable. In the Western plants, the man-power shortage was almost completely overcome and new capacity has been or is in the process of being added to three plants; thus by December of 1948 daily zinc metal production had risen to the highest point since May of 1944 despite strikes in one large primary smelter and in one secondary plant.

Jan 1, 1949

By W. T. Isbell

Although the pressure to meet the heavy demand for lead still took precedence over new metallurgical developments in the field of roasting, smelting, and refining of lead in 1948 there nevertheless has been considerable activity in the experimental development of new processes and improvements as well as plans for the modernization of many plants both here and abroad. Increasing labor and material costs have stimulated the trend to greater mechanization, revamping of flow sheets, and construction of larger units wherever possible. Although there have been many serious labor stoppages in the United States, Mexico, and Europe, labor supply has improved in most plants even if it has fallen off in efficiency.

Jan 1, 1949

By Harold B. Fell

MANY oil producers are in disagreement with the idea held by some that an increase in the price of crude oil would be unlikely to stimulate much production and that we will be obliged to draw upon foreign sources of petroleum to supplement our domestic production as the years go by. Supporting our con trary opinion are numerous facts and figures. The most recent official estimate of the maximum efficient rate of production from the oil wells of the United States is 5,271,000 bbl per day. The Economics Advisory Committee of the Interstate Oil Compact Commission estimates, assuming certain supplies from imports and from natural gasoline and benzol, that crude oil require-

Jan 1, 1947

By Franklin G. Pardee

WARTIME depletion of the reserves of iron ore in the Lake Superior region of the grade and character now being shipped down the Lakes was serious. The time has come to take stock of the resources that remain in order to plan our future program of supply for our blast furnaces and protect, as far as possible. the tremendous investment made in the Lake Superior iron mining industry. Hugh M. Roberts and William H. Crago have estimated the reserves of the Lake Superior region in the United States at two billion long tons. These reserve figures are of direct-shipping ore and those concentrates produced by methods now in commercial use or those methods that may be expected in the near future. In their estimate they have assigned 392 million long tons to the Michigan ranges (all reserves in long tons) : 112 million tons for the Gogebic. 140 million tons for the Menominee, and 140 million tons for the Marquette.

Jan 1, 1948

By Walter Crafts

KEYNOTE of the technical sessions of the Iron and Steel Division at the Annual Meeting was struck by Leo F. Reinartz in his Howe Memorial Lecture on "The Development of Research and Quality Control in a Modern Steel Mill." In describing recent developments in steel-producing practices at the American Rolling Mill Co. the co-ordination of practical observation and directed research with operations was stressed and was shown to have resulted in economical production of steels of uniformly high quality. Empirical methods based on inaccurate and incomplete experience resulted in the production of commercial products of variable quality and were recognized as inadequate; a research program was therefore initiated that has been justified by its fruits. To name a few outstanding achievements such as Armco iron, steel for electrical sheets, wide continuous strip of superior surface and quality, and non-aging steel is not sufficient to summarize the results of this increasing effort toward better steel products. In addition to the development of new products the faithful observation of operating procedures, the co-ordination of the resulting information, and the standardization of processes have made the steel of today much more uniform and thus more economical and useful to the nation.

Jan 1, 1943

By O. E. Kiessling

THIS announcement of the topics relating to production control, which the Committee hopes to have discussed at the February meeting, supplements the preliminary announcement published in the November number of MINING AND METALLURGY. In the previous article, the writer indicated the kaleide-scopic nature of the questions involved in obtaining better coordination in industry, and that, as a matter of practical expediency, the discussion in February would be limited to the more obvious difficulties in industry which need attention and to those questions which the Committee thinks would be of greatest interest to members of the Institute. But while practical considerations necessitate limiting the program, free discussion of all phases of the subject is urged by 'the Committee. In a preliminary consideration of the production control problem, there loom up two questions which have to be faced: (1) First, there is the question of the extra industrial capacity necessary to meet demand during the ordinary fluctuations of business, commonly characterized as `the "business cycle." Anyone who tries to formulate a program pertaining to productive capacity must decide whether he wishes to discuss the control of business cycles. While this question may eventually lend itself to treatment, the Committee does not feel that it can be considered at present with much profit. (2) The second question arises from the existence of over-stimulated capacity above and beyond peak demands in boom times. Discussion of this topic, it is felt, would be most fruitful. How to prevent capacity from being over-stimulated to an extent beyond any hope of possible demand is a

Jan 1, 1929

A SPRING meeting is to be held at Cleveland this month under the joint auspices of the Iron and Steel Committee and the Ohio Section with the cooperation of the neighboring sections in Pennsyl-vania, Illinois, and the other States of the Great Lakes region. The discussions will be focused on just one subject, that of manganese, but will cover that thor- oughly as is indicated by the following list of papers. TECHNICAL PROGRAM Some Political Aspects of the World Manganese Situa-tion. By C. K. Leith, Professor of Geology, Uni-versity of Wisconsin, Madison, Wis. Manganese Resources in Relation to Domestic Con-sumption. By J. V. W. Reynders, Consulting En-gineer, New York, N. Y. Manganese Deposits of the' Gold Coast, Africa. By Sir Arthur E. Kitson, Director of the Geological Sur-vey of the Gold Coast, London; with Notes on the Petrology of Certain Associated Manganese Silicate-bearing Rocks. By Maj. N. R. Junner. Reserves of Lake Superior Manganiferous Iron Ores. By Carl Zapffe, Manager, iron ore properties, North-ern Pacific Railway Co., Brainerd, Minn. Iron Manganese Alloys Low in Carbon. By. Sir Robert Hadfield, Hadfields, Ltd., London. Manganese in Non-ferrous Alloys. By M. G. Corson, Consulting Engineer, New York, N. Y. Importance of Manganese in the Steel Industry. By H. M. Boylston, Professor of Metallurgy, Case School of Applied Science, Cleveland, Ohio. Minnesota Manganiferous Iron Ore in Relation to the Iron and Steel Industry. By T. L. Joseph, E. P. Barnett and C. E. Wood of the North Central Min-ing, Experiment Station, U. S. Bureau of Mines, Minneapolis, Minn. Representatives of the leading steel companies, the Army, the Navy, the Geological Survey, Bureau of Mines, and leading technical societies will be present and a lively discussion of the various papers is already assured. Nearly 14 pounds of manganese is needed for every ton of steel made. Estimates indicate that the total reserves of ore in this country suitable for making ferro would hardly supply domestic requirements for ten years, even if it could all be mined in that time. The grade of ore called for by present practice must come from abroad. The present tariff policy of this country is stated to cost industry $8,000,000 in order to force production of manganese ore to the extent of $600,000. What is the wise thing to do? Should a stock be accumulated? If so, how? Is it feasible to change practice and use low-grade ore or to beneficiate the ores of this grade and meet our requirements? What progress is being made in this direction? ,These and similar questions are raised in the various papers that have been submitted and will be open for dis-cussion.

Jan 3, 1927

By B. S. Butler

A. D. Mutch (Falconbridge Nickel Mines Ltd., Ona-ping, Ontario)—This contribution is prompted by the fact that the writer has recently published an article'!' which has in part the same general conclusions as B. S. Butler's, namely, the form of the standard mineral paragenesis in hypogene deposits and the parallel transition from early high temperature acid to late low temperature alkaline or neutral solutions. Since the writer also recognizes that he is not fully qualified to discuss the formation of ore deposits as a chemical problem, this discussion will be limited to summarizing other observations and will suggest how Butler's Table II might be made more effective. The form of Butler's table is not unlike that widely used by European geologists'" in which the various minerals are related to the types of ore fluids—peg-matitic, pneumatolic and hydrothermal. Thus the decrease in temperature and change in pH of the ore-bearing fluids as recognized by Butler may also be paralleled by perhaps even greater changes in composition, density, and character. W. H. Newhouse's article:" on the sequence of hypo-gene ore mineral deposition is still one of the most complete analyses of the problem. In it he makes four major observations: 1) The order of O, S, As, Sb is the same as their increasing atomic weights and the same as their melting points. 2) The order of the metallic elements is the same as the Schuermann series. 3) The general mineralogical order is paralleled by decreasing heats of formation. 4) The order is generally in decreasing hardness, higher metal content, and higher specific gravity. The order of 0, S, As, and Bi is also the same as their relative abundance. Another point worth mentioning about this series is that As, Sb, Bi, when abundant, often substitute for sulfur in the early pyrite-like minerals, whereas later in the sequence these elements appear to act more like metals. This behavior may be a further indication of the acid character of the early fluids. C. J. Sullivan"' has attempted to show that the sequence of the metallic elements is related to the order of their melting points and has discussed the interrelationship of the different types of bonding of sulfo-phile and oxiphile elements in minerals. Items 3 and 4 might best be summarized by saying that bonding of the minerals in the series appears to be from ionic to covalent to metallic, the early minerals being light in weight, hard, and near-transparent; the intermediate minerals of intermediate weight, semi-transparent, and semi-conducting; and the end minerals heavy, soft, and malleable, opaque and good conductors. A rapid fall in temperature has been assumed to be the cause of ore deposition in many deposits. Perhaps this in turn is the effect of a rapid release of energy in the form of pressure release and change of volume, the first minerals to form being those with the highest heats of formation which absorb the released energy the most rapidly. Butler's Table II could probably be streamlined and made more effective if the listed compounds were assembled as mineralogical groups as in Dana. Thus the sulfides, arsenides, antimonides, bismuthides, and sulfa salts could be arranged in AX,, AX, A2X2, etc. groups. Since these are continuous substitution series, in which the fields of stability and the heats of formation of the various individual minerals can be fairly regarded as similar, this should be accomplished with no loss of clarity. The occurrence of the individual minerals and the precise sequence of the mineral deposition in any one deposit is probably more dependent on the concentration and relative abundance of the component elements. The assembling of geological data in tabular form such as Butler's Table II will continue to be a very effective method of studying geological phenomena. The importance of this particular problem has been pointed out by C. F. Park,% who concludes that understanding of mechanisms of the standard paragenesis and interrelated problems of mineral zoning in space and time is one of the major keys to classification of ore deposits.

Jan 1, 1959

By James Boyd

Scientists and engineers must concern themselves not only with technical problems, but with the socio-economic difficulties of our scciety. The author states that raw materials are basic to the economic process and that mineral raw materials occur naturally in nearly limitless quantities. He feels that the economic pocess will provide sufficient raw materials for man's needs, and discusses in some detail the world economic environment. As our society grows in complexity, it becomes more urgently incumbent upon scientists and engineers to bring their experiences to bear on the solution, not only of technical problems, but also on socio-economic difficulties. It is to this field that I have directed a large part of my energies. RAW MATERIALS BASIC TO THE ECONOMIC PROCESS There are certain premises, frequently overlooked, which bear emphasis. As economics concerns the production, distribution, and consumption of goods, so our whole society is based on raw materials. Without the basic extractive industries of agriculture and mining, there would be no economic problems with which to deal. This principle has been expressed as "All productivity is based on three factors: 1) natural resources, whose form, place, and condition are changed by the expenditure of 2) human energy (both muscular and mental), with the aid of 3) tools.77* It seems strange that such an obvious statement needs to be made. It is forgotten by all of us, however, at one time or another when we get involved in the complicated theories of economics dealing with the financial and fiscal policies of the various governments, in the financing of enterprises, in marketing, and in labor relations. Unless decisions in all of these fields are made with this, and the rest of the "Ten Pillars of Economic Wisdom," consciously in mind, the resultant policies are doomed to eventual failure, whether these are policies of individuals, companies, or governments. The economic process is basic to society. But economics and the social aspects of humanity are inevitably intertwined. If human needs are not provided for within the basic economic structure, conflicts arise to disrupt the most carefully laid social plans. Similarly, it is the failure of society to cope with basic economic prerequisites that leads to discord within the body politic and thus to eventual economic disaster. We who are engaged in the various aspects of the mineral industry, therefore, have a large part to play in society's future development. MINERAL RAW MATERIALS OCCUR NATURALLY IN NEARLY LIMITLESS QUANTITIES Throughout my career in and out of government, I have formed my decisions on two principles: 1) Fundamentally, all mineral raw materials exist within the earth's crust in quantities greatly exceeding man's needs; 2) Any problems of supply of these materials are primarily economic in nature. With respect to my first assumption, analyses by geochemists enable them to estimate the quantities in which each of the known elements exist in the earth's crust. One of the most cautious and famous suggests that the average copper content of the lithosphere to a depth of ten miles is about 55 ppm. If this is valid, then the lithosphere contains about 1.4 quadrillion (1.4 x 10 ") tons of copper metal — an unimaginable quantity. This is 8,500,000-fold that which has been consumed by man in his existence. To illustrate further, consider that the deepest copper mine in history went to about 9000 ft below the surface; the present copper mines of the world now average less than 1500 ft in depth. We can assume that in most continental land areas of the world it is technically feasible to mine to a depth of at least one mile. The land areas of the world to an average depth of one mile, then, contain 343 billion tons (343 x 10') of copper metal, or 2000 times that which has been extracted to date. I don't believe man will ever expend his energies to extract copper from rocks which contain only a few parts per million, but he knows that each element

Jan 1, 1968

By Walter J. Johnson

The coals in northern Wyoming and Montana are free-burning and non-caking and range from lignite to bituminous C in rank. Strip and underground mining are employed to supply railroad, utility, industrial, and domestic fuel. The market area includes Iowa, Nebraska, Minnesota, North and South Dakotas, Wyoming, Montana, the Pacific Northwest, and western Canada. THE larger producing coal mines in northern Wyoming are located in the Powder River Basin lying between the Black Hills region of South Dakota, eastern Wyoming, and the Big Horn Mountains in north central Wyoming, see Fig. 1. The mines are located particularly in the area along the route of the Chicago, Burlington & Quincy Railroad from Gillette, Wyo., to a point approximately 15 miles northeast of Sheridan, Wyo. Fig. 2 is a graph of coal production in the state of Wyoming from 1918 to 1951. Across the Big Horn Mountains lies the Big Horn Basin, situated between the Big Horn Mountains and the Rocky Mountains proper. Mining in the Big Horn Basin is almost entirely confined to a small area known as the Gebo Field, near the town of Kirby, which is located on the Chicago, Burlington & Quincy Railroad. This paper will describe present operating areas, making only brief reference to the history of mining and marketing primarily because of the large area to be discussed. The coal beds presently mined in the Powder River Basin are all of Tertiary age and are of Fort Union and Wasatch formations of Paleocene and Eocene ages, see Fig. 3. The Fort Union formation, consisting of 2000 to 3200 ft of alternate sandstone, shale, and coal, is divided from oldest to youngest into the Tullock, Lebo Shale, and Tongue River members. Most of the mineable coal is in the Tongue River member, which is 500 to 800 ft thick. The Carney coal bed, varying from 7 to 20 ft in thickness, is considered the base of the Tongue River member. About 85 ft above the Carney is the Monarch bed, ranging from 18 to 42 ft in thickness. At approximately 210 ft above the Monarch is what is locally known in the Sheridan district as Dietz No. 3 bed, which varies from 12 to 30 ft in thickness. One hundred feet above the Dietz No. 3 is Dietz No. 2 bed, which is 7 to 12 ft thick. At about 100 ft above the Dietz No. 2 is Dietz No. 1 bed, 7 to 15 feet in thickness. Two hundred and fifteen feet above Dietz No. 1 is the Smith bed, approximately 5 ft thick. One hundred twenty-five feet above the Smith is the Roland bed, which is estimated to be approximately 13 ft thick. The Roland bed is considered the base of the Wasatch formation, which in the Powder River Basin is 1000 to 3500 ft thick and is composed largely of shale, sandstone, and coal. The foregoing measures are the only ones above the Tongue River member that have been mined in the Sheridan field. To the east of the Sheridan field, particularly in the area of Gillette, the Roland bed is considerably thicker and is considered the thickest and most extensive coal bed in Wyoming, reaching a maximum thickness of 106 ft. From 125 to 225 ft above the Roland lies the Arvada bed, average thickness 9 ft. Three hundred seventy-five to four hundred feet above the Arvada is the Felix bed, which reaches its maximum thickness of 30 ft near Echeta on the Chicago, Burlington & Quincy Railroad. East of the Powder River the bed averages more than 10 ft in thickness, but it thins in a northwesterly direction. The highest mineable coal in the Powder River field is the Healy bed, about 400 ft above the Felix bed and exposed only in the highest parts of the area where much of it has been burned along the outcrop. Where it has not been burned, the thickness at most of the outcrops is 10 to 15 ft.

Jan 1, 1954

By P. M. Robinson, M. B. Bever

THE heats of formation at 273°K of the compounds InBi, In2Bi, and TIBi2 have been determined by metal solution calorimetry with bismuth as solvent. The published information on the thermody-namic properties of these compounds is limited. The structure of the compound InBi (mp, 383°K) is tetragonal of the PbO (B10) type.1 The compounds In2Bi (mp, 362°K) and TIBi2 (mp of highest-melting composition, 486°K) are now believed to have structures of the NizIn (B8) type273 and not the A1B2 (C32) structures reported earlier.4, 5 The compounds In2Bi and TIBi2 have limited homogeneity ranges at room temperature, while the compound InBi has no detectable homogeneity range.' Samples of the compounds were prepared from 99.99 pet Bi (Mallinckrodt Chemical Works), 99.999 pet in (American Smelting and Refining Co.), and 99.99 pet Tl (Amend Drug and Chemical Co.) by melting the components in sealed, evacuated Vycor tubes. The compounds InBi and in2Bi were of the stoichiometric compositions. The compound TIBi2 contained 40 pet T1; this composition was chosen because at room temperature the alloy of stoichiometric composition does not lie within the homogeneity range.' The melts were held approximately 50°C above the liquidus for 8 hr and then quenched into iced brine. The samples were homogenized for 48 hr at temperatures 20°C below the temperature of complete solidification. Metallographic examination of sections taken from the center and the ends of the ingots did not reveal second phases or segregation . The heats of formation were determined as the difference in the heat effects on solution of a compound and of a mechanical mixture of its components added from the reference temperature of 273°K to liquid bismuth at 623°K. The details of the calori-metric procedure and method of calculation have been described elsewhere? The calorimeter was calibrated by adding bismuth at 273°K to the bismuth bath at 623°K. The calculated values of the heats of formation of the compounds, listed in Table I, are based on a value of 4.96 keal per g-atom for the difference between the heat contents of bismuth at 273" and 623oK7 No published values are available for the heats of formation of the compounds InBi and In2Bi. Hultgren et a1.7 have calculated a value of -0.50 i 0.10 keal per g-atom for the heat of formation at 423°K of the compound TIBi2 containing 40 at. pet T1 from heat-content measurements in the range from 398" to 700°K and the heats of formation of the liquid alloy. The difference between this value and the value of -0.66 * 0.01 keal per g-atom at 273°K is too large to be attributed to a difference between the heat capacities of the compound and the components over the temperature range 273o to 423oK7 However, the direct determination of the heat of formation by a calorimetric method should give a more accurate value. The heats of formation at 273°K of the compounds InBi and In2Bi lie on a straight line when plotted as a function of composition, Fig. 1. The compound In2Bi, therefore, appears to be barely stable with respect to its neighboring phases. In order for the free energy vs composition curve to be concave towards the composition axis, the entropy change on formation of In2Bi must be more positive than that on formation of InBi. As the compounds are ordered,2, 3, 8 there is no configurational entropy change on formation. The difference between the entropy changes on formation of the two compounds, therefore, is probably associated with the vibrational entropies. In view of the low heats of formation, the changes in vibrational entropy, due to changes in bond strength on formation of the two compounds, are likely to be small. Owing to the volume contractions on formation of the two compounds,5 the vibrational entropies probably decrease slightly but the decrease of the vibrational entropy of InBi is expected to be larger than that of In2Bi.

Jan 1, 1965

By R. Simon, D. J. Graue

This paper presents correlations for predicting the solu-lility, swelling and viscosity behavior of CO2-crude oil sys8i.m~. The correlations were developed from experimental data obtained by the authors. These data are also presented. The data were determined by measuring the properties of mixtures of CO, and nine different oils. Experiinental conditions covered a range of 100 to 250°F and pressures up to 2,300 psia. Properties predicted by the correlations have average deviations, expressed as per cent of experimental value, of 2 per cent for solubility, 0.5 per cent for swelling and 12 per cent for viscosity. INTRODUCTION Interest in CO2 injection as an oil recovery process has led to the development of performance prediction methods which can be applied to specific reservoirs.1 iS To use these performance prediction methods, it is necessary to know the solubility, swelling and viscosity properties of CO2-crude oil mixtures at reservoir conditions. Some information on these properties has appeared in the literature; however, this information did not cover the range of different oils and conditions needed to prepare generalized correlations for reservoir engineering purposes. Consequently, an experimental program was undertaken to collect the data needed. The data obtained and the correlations developed from the data are described in the following sections of this paper. SOLUBILITY OF CO2 IN CRUDE OILS CO2 solubility data in the literature come from six principal sources. The solubility prediction method of Welker and Dunlop3 is limited to 80F. The information in Ref. 4 is of two types: the first includes binary and ternary mixtures of CO, and light hydrocarbons (C1 to C6), and the second gives data for CO1 and heavy hydrocarbons for a temperature range of 40 to 90F. Ref. 5 contains a KCO2 chart for systems whose convergence pressure is 4,000 psia. The KCO2's are based mainly on CO2-natural gas mixtures. Poettmann's work covered CO2 solubility in one condensate and one crude oil6,7 Ja-coby and Rzasa measured CO? solubilities as a function of pressure and temperature for two natural gas-absorber oil mixtures and two natural gas-crude oil mixtures.'8 CO, concentration in these four systems was fixed at 5 mol per cent. The work reported in this paper extends CO, solubility data to a variety of different crude oil types in a temperature range from 110 to 250F and pressures up to 2,300 psia. The experimental procedure used by the authors to obtain the solubility data consisted of combining known amounts of pure CO, and crude oil in a visual cell at a fixed temperature and measuring the bubble point of the mixture. Measurements were made for a total of 40 different CO2-oil mixtures and the results are shown in Table 2. The mixtures included nine different oils (seven crude oils and two refined oils) whose properties are listed in Table 1. All nine oils had vapor pressures less than 1 atm at the experimental temperatures. Consequently, analysis of the bubble-point vapor showed a CO, concentration over 99 mol per cent. At no time during these experiments was a second, more dense, liquid phase observed. The solubility correlation which was developed from the data in Table 2 is presented in Figs. 1, 2 and 3. In these figures, solubility is expressed as xco2 the mol fraction of CO, in the CO2-oil mixture. Fig. 1 shows solubility as a function of CO2 fugacity6 and temperature. Fig. 2 shows the same solubility data expressed as a function of saturation pressure and temperature. The solubility shown in Figs. 1 and 2 is for an oil whose UOP characterization factor is 11.7. UOP characterization factors of crude oils can be determined from Ref. 10 if the viscosity and APT gravity of the oil are known. Fig. 3 gives the solubility correction factor for oils whose UOP characterization factors differ from 11.7. The solubility correlation in Figs. 1, 2 and 3 predicted

Jan 1, 1966