Search Documents

By Charles H. Fulton

Experimental work on the process was begun on a laboratory scale at Cleveland, Ohio, in 1914, and transferred to East St. Louis, Ill. in 1916, where a commercial sized furnace was in technical operation until January, 1918. The essential steps of the process are as follows: Oxidized zinc ore or roasted zinc concentrate is mixed with crushed coke and coal-tar pitch and formed into briquets 9.25 in. (23.5 cm.) in diameter and 21 in. (53 cm.) long in a manner similar to that used in the manufacture of graphite or carbon electrodes, except that much less care and time are required. The composition varies with the nature of the ore; in one case, the composition was 100 parts ore, 70 parts coke, and 18 to 20 parts pitch. These briquets maintain their form and volume during and after the distillation of the zinc. This object is gained by using coke as the matrix and coal-tar pitch as the binder; this pitch becomes coke on heating and unites the ore particle and the original coke particle into a continuous mass. The briquet is an electrical conductor but only to such a degree that it can be used as a resistor. The size of the ore, as in the present practice of zinc metallurgy, ranges from fine material, such as flotation concentrate, to coarse table and fine jig concentrate. The process is not restricted to any particular kind of ore, but is applicable to pure high-grade ores, ores high in iron, and complex zinc-lead ores, since the residue from the distillation IS held immovably in place within the briquet. In the case of complex zinc-lead ores, the distillation is conducted with a carefully regulated temperature so that a high percentage of lead is retained in the distilled briquet, which may then be smelted for its lead content. In present zinc smelting practice, the reduction fuel is from 40 to 50 per cent. of the weight of the ore. In the briquet, it is from 60 to 85 per cent. of the ore; but unless the ore is exceptionally high in residue, the distilled briquet may be used over again as coke, or as a high ash coke for fuel purposes in power production. Baked briquets are hard and tough and may be handled roughly

Jan 1, 1921

By C. A. Hansen

The furnace used for experimental work is shown in Fig. 1. One fireclay sagger, or pot, was set within another and the space between the two filled with Silox heat insulation. The hearth is a cast-iron plate with an imbedded ribbon of nichrome wire; this wire heater is connected to a potential regulator, which permits a very close voltage control. A mechanically driven arm is fitted with rabble blades so arranged that a uniformly thick ore bed may be maintained indefinitely. This arm is usually driven at about one revolution per minute but its speed of rotation can be varied as desired. Compressed air is led into the furnace through a meter, and it was found necessary to preheat the air in order to secure the definitely isothermal conditions sought. With this arrangement, it is possible to maintain any desired temperature constant within about 5" C. for any desired length of time and to

Jan 1, 1921

By C. A. Herbert, C. M. Young

WithIn the past few years, considerable development has been made in the coal-mining industry in Illinois and Indiana and it is the purpose of the authors to record its most important phases. Perhaps the two most striking features are the entry into the producing fields of certain large consumers of coal and the magnitude of some of the new operations. Mines are now being equipped by the Chicago & Northwestern R. R., the Chicago, Burlington & Quincy R. R., the Standard Oil Co., of Indiana, and the Union Electric Light & Power Co. of St. Louis. Besides, the U. S. Steel Corpn. has increased its coal-mining activities by commencing operations on its large holdings northeast of Benton, Franklin CO., Ill. Until recent years, the supply of coal has commonly been adequate and prices have generally been favorable, especially to large consumers, as the magnitude of their purchases enabled them to obtain satisfactory quotations from producers. In fact, most consumers of coal have believed that they could buy their fuel more satisfactorily in the open market than they could produce it themselves. The entry of the United States into the war was accompanied by various disarrangements of industrial conditions, and a demand for coal in excess of the supply seemed likely to be experienced for an indefinite period. Under these circumstances it seemed that the greatest assurance of a supply of fuel was its production by the operation of mines. In the case of the Chicago & Northwestern R. R. and the U. S. Steel Corpn. the production of coal has been carried on for many years with satisfactory results, but the C. B. & Q. R. R., the Union Electric Light & Power Co. and the Standard Oil Co. of Indiana had not been producers of coal, at least in this district. Apparently the most impressive feature of the newest mines is their capacity, for in some cases it is planned that production shall be in the neighborhood of 1000 tons per hr. There are mines now in this field having nearly that output, but these were not planned for such output; in fact, when the shafts were sunk and the machinery installed it was generally supposed that the daily outputs would be only in the neighborhood of 4000 to 5000 tons. Incidentally, there has risen

Jan 1, 1920

By A. E. Bellis

There is a wide difference of opinion among rifle experts in the matter of barrel steel, and the relative importance to the life of the barrel of the steel's composition, heat treatment, structure, and physical properties. In order to promote discussion, which it is hoped may' lead to the discovery of the source of some of the traditional beliefs on the subject, the results of some tests are presented here, with data on heat treating, physical tests, and erosion. The detailed metallographic study of this steel is given in another paper.l The conclusions from these tests should be capable of wider application than their direct bearing on the barrel-steel problem. The Government specifications for barrel steel for model 1903 rifle (Springfield) call for carbon 0.50 to 0.60 per cent., manganese 1.00 to 1.29 per cent., silicon under 0.25 per cent., sulfur under 0.06 per cent., phosphorus under 0.08 per cent. The minimum physical requirements are: Tensile strength, 110,000 lb. per sq. in. (7733 kg. per sq. cm.); yield point, 75,000 lb. per sq. in (5472 kg. per sq. cm.); elongation, 20 per cent.; reduction of area, 45 per cent. Material fulfilling these requirements gives practically no failures when proof-fired, with charge of 70,000 lb. per sq. in. pressure, which is 40 per cent. in excess of the service charge. The turning and drilling operations show up any seams or laps such as accidentally occur even in the best heats of open-hearth steel, so that faulty stock is practically all eliminated before proof-firing. These physical requirements are met either by rolling billets at a proper temperature down to the form of tapered barrel blanks or by heat treating bars that have been upset to cnlarge the breech section. The transformation temperature of this steel, on heating, is around 1350" F. (732' C.), varying somewhat with the composition and the rate of heating. The actual treatment of the barrel blanks, as carried out by different manufacturers, gives four kinds of barrels, which will be called A, B, C, and D, for convenience. A barrels result from heat treating upset blanks by quenching at

Jan 1, 1920

By Carl H. Beal

The most important factors that should be given consideration in the valuation of oil lands are: (1) the amount of oil the property will produce; (2) the amount of money this oil will bring (based upon the future prices of oil); (3) development and production costs; (4) the rate of interest on the investment; (5) the retirement or amortization of invested capital; and (6) the salvage or "scrap" value of the equipment when the property is exhausted. These factors are of varying importance and some of them may not enter all valuation problems, but most of them should be given consideration in any valuation even though only a rough estimate of the value of the property is desired. The value of a property may be changed over night by the completion of important test wells, by the sudden water flooding, or by a change in the price of oil. The best a petroleum engineer can give is the value of the property under the conditions existing at the time the appraisal is made with a fair forecast of future action of the wells and of the price of oil. Our experience in the scientific valuation of oil lands is not broad and there is very little published information on the subject; it, therefore, becomes necessary in studying such problems to form comparisons with the factors involved in the valuation of mines—the closest parallel. One of the reasons for the lack of substantial progress in oil-land valuation methods has been the necessity of making an estimate of the future production of the oil property to be valued. Oil men and accountants have not generally conceded that such estimates could be made with any degree of accuracy. It has been shown, however, in several recent publications that with certain data available reasonably close estimates can be made. The accuracy of an appraisal depends chiefly on the accuracy of the estimates of future production and of the future price of oil. The accuracy of the former is sometimes necessarily based on geological inferences. Geology is not an exact science and geological data in connection with oil production cannot always be mathematically evaluated.

Jan 1, 1921

By F. C. Langenberg

It is the purpose of this paper to present a limited amount of experimental data obtained on the Charpy impact machine. Several concrete examples will be given showing the relation existing between the results obtained upon the Charpy impact machine and the behavior of the parts tested when in service. Although it is pointed out by G. Charpy and A. Cornu-Thenard1 that it is first necessary to determine a satisfactory working process before studying the correlation between the results of these tests and the behavior of the parts tested in service, this ideal course cannot be strictly adhered to. If a certain part repeatedly fails in service and the available tests give no indication of its cause, advantage must be taken of any possible means that will solve the problem; therefore, even though the reliability of the results obtained by the Charpy impact machine have been questioned by many, it was necessary to use this instrument without giving careful consideration to its possible sources of error. It would seem that the conclusions arrived at by Charpy -and Cornu-Thenard justify the assumption that the precision obtained by this machine is comparable to that obtained by the other more common forms of testing. The second general conclusion arrived at by them, namely, that the impact test upon notching does not offer any direct correlation to the ordinary tests, is also borne out by many hundred determinations made in the laboratories at Watertown Arsenal. This statement, however, should be qualified as follows: Other ordinary tests include the static tensile test from bars taken in a longitudinal direction and the Brinell hardness. The author agrees that no law is yet known for the computation of the energy absorbed in the rupture of bars of the same material but of different dimensions. Although Charpy and Cofnu-Thenard do not refer in their valuable article to the use of the Charpy machine in industrial practice, it should be stated that this instrument has been in constant use in the laboratory at Watertown Arsenal for several years, and is now employed for both routine and experimental testing.

Jan 1, 1920

By D. Murgue

The circulation of air in underground workings is subject to a gradual and continuous reduction of its pressure, from intake to outlet, caused by the friction between it and the more or less rough and uneven surfaces of the passages. For comparison with the flow

Jan 1, 1894

By L. C. Graton

The federal taxes on incomes and excess profits are of course heavy. In 1917, the value of the mineral production of the United States was a little in excess of $5,000,000,000. The total of federal taxes for that year, for the mineral producing companies, as computed by themselves, amounts, according to tentative compilations, to about $207,000,000, and the total for the comprehensive group of mineral and metal industries to about $766,000,000, which figures represent respectively 9.5 per cent. and 35.1 per cent. of the total tax paid by all corporations. Because of greater complexities in applying the revenue laws to mineral properties than to most other industries, opportunity is afforded for wide differences of view. The taxes indicated above, therefore, are not final and may conceivably be very materially increased. For 1918, the taxes are expected to be still greater, but no compilations are yet available. Taxes at a high rate are to continue indefinitely. The subject is clearly of gravest import to the mining industry in particular. The Commissioner of Internal Revenue, who is charged by law with the administration and collection of the taxes, is determined that these functions shall be performed in a just and businesslike way. Fairness and finality are to be the chief objectives. In view of the peculiar conditions that attach to the tax program as applied to mines and other wasting industries, like oil, gas, and timber, the Commissioner has resorted to professional advice and assistance by manning a Sub-division of Natural Resources with competent engineers, brought in from the several industries, into whose hands he has placed for solution the technical questions involved. These engineers have a two-fold duty: (1) to devote to the solution of these problems their own knowledge and experience; (2) through their acquaintance with their respective industries, and with the men engaged in those industries, to focus upon these problems, by conferences and otherwise, the best opinion of the country. The principal object of this paper is to acquaint the mining profession with the attitude of the

Jan 1, 1923

By L. C. Graton

The federal taxes on incomes and excess profits are of course heavy. In 1917, the value of the mineral production of the United States was a little in excess of $5,000,000,000. The total of federal taxes for that year, for the mineral producing companies, as computed by themselves, amounts, according to tentative compilations, to about $207,000,000, and the total for the comprehensive group of mineral and metal industries to about $766,000,000, which figures represent respectively 9.5 per cent. and 35.1 per cent. of the total tax paid by all corporations. Because of greater complexities in applying the revenue laws to mineral properties than to most other industries, opportunity is afforded for wide differences of view. The taxes indicated above, therefore, are not final and may conceivably be very materially increased. For 1918, the taxes are expected to be still greater, but no compilations are yet available. Taxes at a high rate are to continue indefinitely. The subject is clearly of gravest import to the mining industry in particular. The Commissioner of Internal Revenue, who is charged by law with the administration and collection of the taxes, is determined that these functions shall be performed in a just and businesslike way. Fairness and finality are to be the chief objectives. In view of the peculiar conditions that attach to the tax program as applied to mines and other wasting industries, like oil, gas, and timber, the Commissioner has resorted to professional advice and assistance by manning a Sub-division of Natural Resources with competent engineers, brought in from the several industries, into whose hands he has placed for solution the technical questions involved. These engineers have a two-fold duty: (1) to devote to the solution of these problems their own knowledge and experience; (2) through their acquaintance with their respective industries, and with the men engaged in those industries, to focus upon these problems, by conferences and otherwise, the best opinion of the country. The principal object of this paper is to acquaint the mining profession with the attitude of the

Jan 1, 1923

By S. W. Parr, A. R. Powell

FOUR general methods have been used in the study of the decomposition of coal. The first has been directed toward the processes of coal formation, the second has been by means of microscopic studies, the third from the data of destructive distillation, and the fourth has made use of various solvents. Applying these methods to the sulfur of coal, it has been found that the organic sulfur of plant and animal life enters into the formation of coal and remains in organic combination in the final product. The inorganic sulfur is almost entirely combined as iron pyrites and marcasite. The infiltration of hydrogen-sulfide waters is doubtless a large factor in these combinations. Sulfates are found in very small quantities except where free oxygen has entered the coal strata. The mechanical mixing of detritus with the early coal material is another source of sulfur. In this case the sulfur is distributed in microscopic particles throughout the mass. In destructive distillation, a part of the sulfur comes off as hydrogen sulfide and various thiophen compounds, but this furnishes little information as to the nature of the sulfur compounds in the coal itself. The use of solvents has given valuable data concerning the sulfur compounds in coal. Fremyl and later E. Guignet2 noted the action of alkaline solutions on coal after treatment with nitric acid and Anderson and Roberts3 showed the presence of large quantities of organic sulfur in the extract so obtained. In a study of the phenol extract of coal, Parr and Hadley4 found organic sulfur in the soluble organic material. These investigations proved the presence of organic sulfur in coal in addition to the inorganic forms, such as iron pyrites and sulfates. T. M. Drown6 attempted the analysis of the pyritic and sulfate sulfur as distinct from the organic forms by means of sodium hypobromite; no definite proof of

Jan 1, 1920

By C. C. Nitchie, G. S. Brooks

With the gradual depletion of the natural-gas pools of the Kansas district, together with the uncertainty of further cheap fuel developments, some of the western zinc companies turned to the coal fields, attracted by their permanency and the success of the Matthiessen & Hegeler Co. and the lllinois Zinc Co. Being then confronted with the problem of using a relatively high-priced fuel, although the ultimate supply was very great, the fuel economies of the kilns and furnaces became of far more importance, and the more modern equipments, as a result, embodied distinct gaias in this phase of the business. In addition, there have been some pronounced advances in the actual making of gas from these coals. Increased efficiency in gas making has contributed its hare to lowering costs and those plants located in the higher priced fuel districts have probably been obliged to study these economies somewhat more closely. Naturally, many beneficial changes have resulted in both practice and apparatus in these sections. On certain western coals, for instance, the actual saving in fuel consumption has been 50 per cent. By this is meant that, where about 1.75 tons were burned to smelt 1 ton of oxidized ore, 0.7 to 0.9 ton is now required. While comparisons by T. R. Ingalls1 of fuel economies in smelting in this country and Germany before the war may, in general, be correct, they do not appear to do justice to the more progressive American practice. It is doubtful whether German plants were substantially bettering these fuel ratios. Data furnished by Bender and Frams do not afford records averaging less than 0.9 ton coal per ton ore on materials from 40 per cent. to 50 per cent. zinc. Fuels As producer fuel, Illinois, Indiana, and Kansas coah offer a wide range of material, although varying much in their amenability to gasscation. The proper fuel for each plant can only be determined after com-

Jan 1, 1920

By O. Bilharz

The rules laid down by Peter von Rittinger in his classic Lehrbuch der Aufbereitungskunde (Berlin, 1867, p. 513) concerning the designing of dressing-works still possess authority for such works and their operation. Nevertheless, some modifications and additions suggested by practice may be of value at the present time. Rittinger says: "I. Choose the apparatus and machines which can be, under the existing con-' ditions, easily constructed and kept in running order!' This rule contemplates the construction of apparatus (mostly of wood) on the spot, with the command of good sbops and especially of good workmen in wood. But in many cases, particularly for the sake of a prompt supply, the construction of apparatus is now left to special manufactories, which pay more attention in the choice of materials to durability and strength than to easy manipulation and erection. Nevertheless, here,as in many other instances, simplicity of construction and solidity of execution are to be recommended. Especially important is the convenient and cheap replaceability of

Jan 1, 1894

By I. C. White

Only two factors appear to be directly responsible for the geographic distribution of sulfur in the coal fields of West Virginia: these are the stratigraphic position of the coals in question, and the eastward or westward location of the deposits. There appears to be a progressive increase in the sulfur content of West Virginia coals from the oldest Peqnsylvanian deposits in the Pocahontas, New River, and Kanawha Groups of the Pottsville Series up through the Allegheny, Conemaugh, and

Jan 1, 1920

By S. F. Emmons

The first paper which appears in the published Transactions of our Institute is that read by our respected Secretary at its first meeting in Wilkes-Barre in May, 1871. It is entitled " The Geographical Distribution of Mining Districts in the United States," and presents a brief but masterly review of what was known of the distribution of our deposits of useful minerals, particularly the metals, not only from a geographical but from a geological stand-point. At the request of Dr. Raymond I agreed, somewhat hastily, perhaps, to write for this occasion a brief sketch of the geological distribution of the deposits of the useful metals in this country, in the light of the increased knowledge of the present day. In the time given no personal investigation was possible, and as it was therefore out of the question to attempt to make anything that could be considered an original contribution to the history of our ore-deposits, I have been obliged to limit myself to an examination of such pub-

Jan 1, 1894

By W. Rogers Wade, Alfred Wandtke

The Pilares mine of the Moctezuma Copper Co. is situated at Los Pilares de Nacozari, Sonora, Mexico, about 75 mi. (120.7 km.) south of the international boundary and about 7 mi. (11.26 km.) east of the town of Nacozari de Garcia. It is situated at an elevation of 5000 ft. (1524 m.) in one of the northward trending ridges that form part of the mountain mass that culminates in the Sierra Madre de Mexico. To the east, south, and west, the topography is rugged and diversified; to the north less diversity exists, ranges of mountains rise sharply out of almost level ground and give the basin range structure characteristic of the Southwest. The climate is dry, the average rainfall of 15 in. (38 cm.) being confined almost entirely to the months of June, July, and August. The winter consists of a few days of disagreeable weather when a little snow may fall; the remainder of the year is thoroughly delightful. Vegetation is typical of a semi-arid region. In the canons near the mine, where water flows intermittently, willows thrive; on the northern slopes of some of the mountains and in some of the broader canons pines may even become abundant. The dominant rocks are flows and pyroclastics which are cut by dykes, stocks, and batholiths. The mountain just west of Nacozari is, in part, composed of limestone of an unknown age which occurs as a syncline and is undoubtedly a part of a prevolcanic land surface. Overlying the limestone and faulted against it, are the volcanics; cutting the limestone is a coarse biotite granite. Whether the granite is older or younger than the volcanics has not been definitely established. No attempt has been made to differentiate the rock types of the volcanic~, of which there are exposed 3000 ft. (914 m.) in thickness of basic and acid flows (andesites, latites, and rhyolites) and andesite and latite tuffs and breccias. The latite breccias, the youngest of these volcanic~, cover the highest mountains in the immediate vicinity. The

Jan 1, 1920

By H. M. Merry

The graphic methods and records described in this article have been developed, with satisfactory results, for the use of executives of the Chino Copper Co., in Hurley, N. Mex. Particular attention is directed to the use of large wall-charts, the quick reference display of large charts, the scale notation of metallurgical charts shown in Pig. 3, and the inclusion of mesh extraction on screen analysis diagrams. To properly comprehend the operation and metallurgical results from a concentrating plant, a daily record of essential data is kept, usually involving the dry weight of ore milled or treated, dry weight of concentrate or metal produced, assay values of heading, assay values of tailing, assay values of concentrate, and percentage of extraction or recovery. In addition it is often necessary to record moisture, pulp density, or dilution, percentage of weight of oils and reagents employed; screen analyses of grinding conditions, oversize, etc.; assay values of non-valuable or interfering substances; cost data; and such special information as may be required. GRaphic Presentation . Close analysis is necessary of a daily operation involving such a number of factors, the relation and influence of which may be of great importance in the treatment scheme. When the analysis is made from a numerical tabulation, the chance for one or more obscure, but perhaps important, factors to escape notice is considerable, therefore the need for an accurate, readily digestible presentation of metallurgical data is obvious.. Graphic records of milling operations are frequently used, but owing to the wide range of magnitude and values, and the number of factors involved, the customary practice of assigning different values to the same ordinates, as in Fig. 1, results in a complex and intricate record which makes little appeal to a busy operating official. The methods shown in Figs. 2 and 3 are devised to display such data in a clear and legible manner, without confusion.

Jan 1, 1920

By Paul D. Merica, L. J. Gurevich

In connection with other investigations on the properties and characteristics of chilled-iron car wheels, the question as to the best range of annealing temperatures was raised. Chilled-iron wheels are cast with a chill against the tread and the inside of the flange, the remainder being in sand. The composition of the metal is so chosen that under these conditions the trcad and inside of the flange will show white iron to a depth of from 5/8 to in. (15 to 22 mm.), the remainder of the wheel becoming graph itized or gray. In order to relieve the stresses set up during cooling under such drastic conditions, the wheels are stripped from the mold, while still red hot, piled in a soaking pit, and allowed to cool very slowly from their temperature at stripping. Obviously the most suitable temperature for this annealing is the highest at which no formation of graphite occurs within the white tread and at which the wheels can be stripped from the molds. Inasmuch as no direct determinations have been made of the temperatures at which the formation of graphite takes place in white iron of compositions used in car wheels upon annealing, it was considered worth while to determine these temperatures as a means of establishing the maximum temperatures at which the annealing of the wheels may be carried out. In the course of this work, some incidental observations were made which are of interest in connection with the theory of graphitization in whitc iron. The literature on the subject of the formation of graphite both during cooling at casting and upon annealing is very extensive and can be best studied by reference to a comprehensive discussion of the subject by Hatfie1d.l Perhaps the most important contributions of previous investigation are the following: 1. Whether a given mass of molten iron becomes white, mottled, or gay upon casting, depends on its composition and its rate of cooling through the temperature range of solidification and immediately below. 2. The more rapid the rate of cooling, the less is the extent of graphitization.

Jan 1, 1920

By Arvid E. Nissen, Knox Taylor, John H. Hall

Some months ago one of the authors was asked to write a paper on the heat treatment of steel castings that would be more comprehensive than other matter he had published; this is an attempt to present in condensed form the results of experimental work and actual practice carried out for the most part in 1907, 1908, and 1909. It is not a laboratory research and the work done was carried out for the express purpose of putting in practice the processes discovered as fast as possible. Most of the tests are the result of commercial practice and not of bars annealed in our laboratory; most of the micrographs were made for our own records and not for publication. Certain of the micrographs, therefore, are not as clear as we may wish but they were good enough for our purpose at the time they were made. The tests and micrographs are selected from several thousands in our files. All of these micrographs are magnified 60 diameters. These experiments were conducted almost entirely on steel made in a 3-ton bottom-blown converter, and most of the steel illustrated analyzes about 0.05 in phosphorus and sulfur. Unfortunately, a certain number of specimens are shown of which we do not have the complete analysis, but in most cases in which the phosphorus and sulfur vary much from the figure just given that fact is noted. For purposes of comparison, we have included a certain number of micrographs and tests of steel made in the electric furnace, some of which were from specimens made in other shops and some in our own shop, and some tests of acid open-hearth and tropenas steel. A brief examination of the tests in Table 1 shows that certain treatments of, for instance, 0.30 per cent, carbon steel are not represented by any test data. Had this been a laboratory research, this information would undoubtedly have been furnished, but as this work was done for commercial purposes the omissions are due to the fact that, at the time the work was done, we saw no advantage in trying every composition of steel with each treatment discussed in the paper.

Jan 1, 1920

By C. M. Young

The safety lamp is the most common and convenient apparatus for detecting inflammable gases in mines, the presence of gas being shown by a blue flame, called the cap, if the wick has been lowered to suppress the luminous flame. The height of the cap increases with the proportion of gas and with the temperature of the lamp flame. Lamps of the Wolf type, the fuel of which is benzine, have a hotter flame than lamps in which vegetable oils are used, such as the Davy, and the Clanny, and are more sensitive than the latter and their many modifications. The Piehler alcohol lamp gives a still higher cap while the Clowes hydrogen lamp is most sensitive of all. While the effect of the temperature of the source of ignition is well known, the writer knows of no previous attempt to correlate the change of this temperature with change of the height of the cap produced, In order to determine the height of the cap at various temperatures, it was necessary to have a source of ignition the temperature of which could be accurately controlled over a considerable range. This condition was met by a coil of wire of high fusing point heated by an electric current controlled by a variable resistance. The use of a coil offered the further advantage of freedom from complications due to the flame of a burning fuel. Such a flame, being itself of variable height, would to some extent raise or lower the elevation of the base of the cap and therefore add to the difficulty of determining the height of the cap. Besides this, the presence of a small cap from the lamp fuel, commonly known as the "fuel cap," would interfere with the observation of small gas caps. After some experiment, a coil was made of platinum wire, No. 26, diameter 0.016 in. The coil was 17/64 in. (6.746 mm.) in outside diameter and had eight full turns in a length of 1/2 in. (12.69 mm.). This was connected to an electric circuit through an adjustable resistance, as shown in Fig. 1. In order to measure the temperature, a thermocouple was inserted in the center of the coil; the leads passed out at the ends and were ccnducted to a millivoltmeter. It is probable that the current of air passing upward through the coil resulted in the indication of a tempera-

Jan 1, 1920

By H. A. Keller

(Chicago Meeting, being part of the International Engineering Congress, August, 1803.) Among the important implements of most of our Western lead and copper smelting-works is the slag-cart or buggy, commonly called slag-pot. A large number of such slag-pots being in service, durability, as well as lightness of running, is an important requisite, since repairs, though trifling in each single instance, may amount to a considerable item of cost in the course of a year. They should therefore be seldom necessary and inexpensive when necessary. Light run-

Jan 1, 1894