Search Documents

By Steven Derycke, Stephen C. Tadolini, Anand Bhagwat

"The tensile and shear strength of intrinsic bolting support systems has always been a major concern of designers. A comprehensive laboratory testing program was designed to evaluate the tensile and shear strength of individual wires and completely wound PC-strand cables. PC-strand cables with smooth wires and the recent anchorage enhancement innovation of indentation were evaluated and compared. The testing protocol detailed in ISO Standard 15630 utilizes a mandrel system that was investigated at 3 different diameters which alters the wire to mandrel ratio from 2:1 to 9:1. The results demonstrate that the difference between smooth and indented wires is statistically insignificant when larger diameter mandrels are used, and that indentation does not adversely affect strand properties and performance. Insight into the shearing mechanism and evaluation techniques are discussed with the introduction of triaxial loading to describe the PC-strand tensile and shearing mechanisms. Another important result indicates that the shear strength of PCstrand cable bolting systems has a greater shear strength value than traditional steel bar bolting systems.INTRODUCTIONPC-strand cable bolts have proven to be a global cost effective ground control solution in metal/non-metal and coal mines. The inherent strength to weight ratio of cable supports, combined with flexibility has been used in underground entries that range from 20 to less than 1.2 m in height (65 to 4 ft). In coal mining, the systems are used as primary and secondary support installed both passively or actively with installation tensions that range from 38 to over 178 kN (8,500 to 40,000 lbs) . While cable can be specified in several diameters, the most predominant sizes in the US remain 15.2mm (0.6 in) and 18mm (0.7 in). The capacity of the systems defined in the ASTM 432-13 is 90% of the minimum strand strengths of 260 kN (58,600 lbs) and 320 kN (72,000 lbs), respectively.Cables are not only suitable to support vertical loads, but are also often used to effectively support fractured and jointed materials and can be exposed to shear forces across the wound PC-strand structure. In fact, Goris et al. reported that cable bolts placed across jointed surfaces could more than double the shear resistance. These results were duplicated for both smooth and rough jointed surfaces (Goris et al., 1996). An example of tensioned cable bolts used to support a fractured and sliding roof in a longwall tailgate entry is shown in Figure 1."

Jan 1, 2015

By Isabela Leao Amaral da Silva, Alice Barreto Bevitori, Frederico Muylaert Margem, Victor Bastos da Silva, Sergio Neves Monteiro, Artur Camposo Pereira

"The jute fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of DGEBA/TETA epoxy composites reinforced with jute fibers with different diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned jute fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, separated fibers with smaller larger diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinnest jute fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionThe interest of this research is to develop composites with epoxy resin matrix reinforced with continuous and aligned jute fibers, for applications in various industries, including construction and automotive industry. Conflicts related to the use of non-renewable forms of energy are increasing the interest to enter the market to replace natural materials, synthetic materials synthetics have a higher power consumption in its manufacture [ 1-4].Therefore, applications of natural lignocellulosic fibers obtained from cellulose-based plants are receiving increased attention as an alternative to replace more environmentally correct nonrecyclable materials, energy intensive and glass fiber composites in [5-6]. The use of composites reinforced with natural fibers is a reflection of the concerns with environmental issues such as pollution caused by waste that is not biodegradable or cannot be incinerated and climate change due to C02 emissions associated with the processes of intensive energy and also motivates this work to develop self-sustaining, since natural fibers generate a source of income, especially in developing countries, where most originate, encouraging the cultivation of non-food agriculture [7-9]. Additionally, it is worth also remembering that these fibers come from renewable sources, in addition to being abundant, inexpensive and have a relevant set of mechanical properties [10]."

Jan 1, 2013

By Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Denise Cristina Oliveira Nascimento, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The piassava fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of polyester composites reinforced with piassava fibers with thinner diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned piassava fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, individually separated fibers with the smaller diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinner piassava fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionA significant change in the transportation sectors mainly the aerospace and automotive, occurred last century with the introduction of stronger and lighter materials. The most relevant example was the polymer composite reinforced with synthetic fiber. They are nowadays replacing conventional materials such as the aluminum alloys in airplane body owing to superior specific strength. in recent years, however, environmental problems in a global scale are imposing a reversion in the use of synthetic fiber specially the glass fiber. In spite of its higher specific strength, this fiber and its polymer composites can neither be recycled nor incinerated in a thermal plant to generate electricity [1]. Moreover, the fabrication, processing and transportation of a glass fiber composite are associated with C02emission, the major responsible for global warming [2].A possible substitute for glass fiber without the above-mentioned environmental problems, could be a natural fiber. In fact, natural fibers obtained from cellulose-rich plants, also called lignocellulosic fiber, are already being used in several engineering fields, particularly the automobile industry [3-6]. Figure 1 illustrates an automobile and its many components made of lignocellulosic fiber composite [7]."

Jan 1, 2011

By Lucas Lopes da Costa, Sergio Neves Monteiro, Rômulo Leite Loiola

"Composites with DGEBA/TETA epoxy matrix reinforced with thinner and continuous bamboo fibers stripped from culms were mechanically characterized by tensile tests. Specimens with up to 30% in volume fraction of aligned fibers were tensile ruptured at room temperature. The results showed a steady increase in both the ultimate strength and the elastic modulus of the composites with the amount of incorporated bamboo fibers. The fractographic analysis by scanning electron microscopy showed evidence of moderate adhesion between the bamboo fiber and the epoxy matrix. This fiber/matrix adhesion by interaction mechanism apparently justifies the improved tensile properties of the composites.IntroductionIn recent years polymer composites reinforced with natural fibers, mainly those lignocellulosic obtained from plants, have been subject to extensive research works [1-5]. Environmental, economical, societal and technical advantages of these composites are motivating their substitution for similar polymer composites reinforced with synthetic fibers. In particular, R & D efforts have been conducted aiming to replace glass fibers composites that are comparatively more abrasive to equipments, non-recyclable, more expensive, heavier and toxic [6]. Among the many lignocellulosic fiber composites being investigated, those fabricated with bamboo stripped fibers, i.e., fibers longitudinally cut from the culm, still need information to support possible industrial applications. Several works, however, have been dedicated to bamboo stripped fibers as possible reinforcement of polymer composites [7-17]. These works reported mechanical properties that could markedly vary with the type of polymer matrix, the fiber disposition (if continuous, aligned, short-cut, mat interlayered, etc) and the test condition."

Jan 1, 2011

By J. E. Russell, Y. J. Wang

In this paper, we report the results of a study of the characteristics of Texas lignite based on a proximate analysis data base previously published by the Bureau of Economic Geology, University of Texas at Austin and the U.S. Bureau of Mines. The original impetus for this study was the desire to perform a parameter study in connection with the siting of potential underground gasification tests in Texas. A numerical model of the gasification process was available and required proximate analysis data, among other parameters, as input. If proximate data were available for a particular site, a prediction of the product gas quality could be made. However, in preliminary siting studies, it would be advantageous to know what the desirable characteristics of the lignite are, in order to target general areas for drilling. Consequently, a parameter study was in order. This paper presents the methodology required to systematically vary proximate analysis parameters and estimate the corresponding energy content for various group(or formation)-facies classifications of Texas lignite.

Jan 1, 1983

By L. B. Kilius

The composite cathode system based on Ce0.9Gdo.1O2_,5 electrolyte with a painted cathode was used for an intermediate temperature (500-700°C) solid oxide fuel cell. This cathode system was chosen due to its excellent thermal expansion match to the electrolyte, its relatively high conductivity (115 S cm-1 at 700°C), and its low activation energy for oxygen reduction (99 kJ/mol). It was found that the decrease of sintering temperature of the composite cathode system produces a significant decrease in charge transfer resistances to a level of 0.25 SI cm2. The conductivity measurements of porous samples produced values between 40 and 88 S/cm for porosities of 30-40%.

Jan 1, 2005

By R. A. L. Drew, F. Edelmann

Brazing is a low-cost process used extensively in the manufacturing and repair of aircraft gas turbine engines. Components within the compressor stage of the engine experience relatively low temperatures (600-700°C), therefore joints of stainless steels are typically employed. In such joints, a Pd-Ni-Cr-Si-B (PalNiCroTM) brazing alloy is used as a sealant, however brazing procedures are not well understood. The wetting behavior of PalNiCroTM on AISI 347 was evaluated with respect to contact angle. A microstructural evaluation was carried out with variable joint clearances. Microhardness profiles were performed to investigate the presence of hard secondary phases, which were later confirmed by electron microscopy. The results indicated an equilibrium contact angle of 10° within 100 seconds. The average microhardness of the braze layer and base metal were approximately 550 and 205 VHN, respectively. At the interface, a diffusion zone was present containing carbides and borides.

Jan 1, 2004

By M. Bennett, L. Twidwell

Montana Tech has embarked on a coordinated series of studies to delineate the characteristics of the Berkeley Pitlake containing over 36 billion gallons of acidic, metal-contaminated water formed after the cessation of open-pit copper mining in Butte, Montana, USA. The objectives of the overall series of studies are to summarize presently available information and to generate new and needed information to formulate a conceptual environmental model for the pitlake and to provide characterization data for the development of advanced treatment technologies. In this presentation, the chemistry of the Berkeley Pitlake water is partially reviewed. It is known that the pitlake consists of two distinct layers of water referred to as surface and deep water. Samples of deep water were collected and placed in a 12-ft high and 6-inch diameter column and exposed to different wavelengths of UV radiation as well as atmospheric conditions. Measurements of pH, redox potential (EH), dissolved O2, turbidity, conductivity, temperature, and elemental composition show that the water reacts differently and indicates that the diurnal effects of sunlight likely play a major non-biological role in its chemistry. Resulting technology could be useful for developing an alternative to treating acid-rock drainage.

Jan 1, 2007

By Katsunori Okaya, Toshio Inoue

"Movement of mill charge in the centrifugal mill is essentially dissimilar from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. This dissimilarity is the reason for the substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Bradley et al. (1983) developed a math model regarding the mill charge as a lump. This model is presented in a simple equation with which motion of the mill charge can be predicted in terms of the parameters describing the specification and the operation of the centrifugal mill. This equation can be used to explain the power draft of the mill as well as the stability of mill operation. More recently, on the other hand, a numerical simulation technology called discrete element method (DEM) has become a vital vehicle for estimating the motion of the grinding media in the mill. The authors developed a mill simulator called ‘Mill Solver’. Mill Solver is designed to simulate various types of mills including centrifugal and vibration mills. The principle of this simulator is to calculate individual kinetic events of interaction of balls in the mill in a minute time interval, hence the mill performance can be constructed for estimation."

Jan 1, 2003

By T. Inoue, K. Okaya

"Movement of mill charge in the centrifugal mill is essentially different from that in the vibration mill with circular path despite the apparently similar mode in the motion of mill body. As proved e.g. in [11], this results in substantial advantage regarding the comminution intensity of the centrifugal mill over the conventional vibration mill accounting approximately to one order of magnitude.Back in 1983, Bradley et al. presented a model of the centrifugal mill based on the kinetics of the mill charge by regarding it as a lumped mass. On the other hand, numerical modeling by ‘discrete element method (DEM)’ enabled us to observe the movement of each ball in the centrifugal mill with an extremely minute time intervals (Inoue et al., XX IMPC in 1997). The former approach rendered simple, even though approximate, expression of the mill behavior, while the latter method was advantageous in describing the behavior of the mill in terms of individual events taking place in the mill body, even though the result did not reduce to a simple expression. The characteristics of the centrifugal mill described by both these approaches proved to be in a degree of agreement. Thus, the kinetic approach was capable of presenting the overall view of the mill, while the DEM model was informative of the details that could not be depicted well enough by the simple math expressions."

Jan 1, 2003

By A. R. G. Azevedo, G. C. Xavier

"This work has for objective to identify the soil of the neighborhood Codin located in a lacking area of the urban nucleus of the district of Campos dos Goytacazes - RJ, after the identification the best line was determined for the production of soil-cement blocks. In this area it happens habitational deficit and precarious constructions are also verified. The use of soil cement blocks is considered a cheaper constructive method than the conventional (ceramic block or of concrete), because one of the components of the raw material is abundant (the soil) and the constructions can be erect with certain easiness for collective effort regime. Samples of soil of this area were collected for they be characterized with relationship to the physical and chemical characteristics, with I aid of GPS the community's location it was registered. Identified the soil type, the work began the study of lines they to make possible your use in an economical and safe way. For that were made drained blocks in the format 19,5x10x5 cm, with lines containing the addition of 5% and 10% of cement in volume, and as parameter of quality the absorption of water and the resistance to the compression were measured, following the Norms of ABNT.IntroductionWe know that the use of the soil by the humanity come from the antiquity. And ifs confirmed by the archaeology places of the old civilizations of the word. The most remote constructions date from 10.000 years old in Jericoh, in the Jordan River Valley. This work became more intensive at 3.000 B.C. (Before Christ), by people who lived in those valleys with mood areas, a lot of clay and washed by the rivers.Almost all the sectors of engineering of soils choose the stability to use the local soil. Although, artificially treated, offers more economical advantages.The stability of a soil consist of endow it of the condition to resist the deformations and ruptures during the period that it is being used, because these characteristics are necessary in any construction.The application of the natural soil only is possible in places that they are of good quality and attend to the requirements of engineering to the type of previewed application. The granulemeter correction and the chemical stability include cases of inappropriate soils areas, turning the soil able to be used as construction material. Among the stability agents, usually added to the soil for stability ends, the cement is indicated."

Jan 1, 2013

By L. S. Jeffrey

Estimates for South Africa?s coal recoverable reserves made in 1999range from nine to 59 billion tons; latest estimates by the Minerals Bureau suggest that 33 billion tons is a more likely figure. As much as 70% of that coal is located in the Waterberg, Witbank, and Highveld coalfields, as well as lesser amounts in the Ermelo, Free State and Springbok Flats coalfields. However, the Witbank and Highveld coalfields are approaching exhaustion (estimated 9 billion tons of recoverable coal remaining in each), while the coal quality or mining conditions in the Waterberg, Free State and Springbok Flats coalfields are significant barriers to immediate, conventional exploitation. New extraction technologies, technologies exploiting the energy content of the coal in situ, as well as suitable uses and markets for low-grade, high-ash coal are required before the country can utilize its admittedly vast coal resources. Major challenges for exploiting some Limpopo province coalfields are severe water shortages, insufficiently developed infrastructure, fragile environments and poor roof conditions due to the depth and complex geology. In the Central Basin (Witbank, Highveld and Ermelo coalfields) technical innovations for thin seam extraction, economic mining of both pillar coal and intrusion-fragmented resource blocks and the utilization of lower-grade coals are required. The success of the fluidized bed combustion technology is necessary to utilize the low-grade coals of the Free State and Molteno coalfields, while environmental exemption for past problems, together with strategies for mining small, disjointed thin-seam resource blocks, is required in KwaZulu-Natal. Clean coal technologies, coal cost and quality, environmental considerations, sustainable development, the growth of the South African economy and Government?s regulation of the electricity industry are the main challenges to the continued use of coal as South Africa?s primary energy source.

Jan 1, 2005

By J. W. Matousek

"Computer modeling of smelting processes requires internally consistent equations for calculating the compositions of mattes and slags. That is, the sum of the calculated assays must total 100%. One set of equations that satisfies this requirement for copper produced under oxidizing conditions (pSO2>one atmosphere pressure) is given by the following:%[Fe] = 62.0 – 0.775%[Cu]%[S] = 28.0 – 0.00125%[Cu]2%[O] = 10.0 – 0.225%[Cu] + 0.00125 %[Cu]2Mattes containing nickel in appreciable quantities do not have the defined “white metal” end point of approximately 80 percent copper and 20 percent sulphur that is found in the copper system during the converting process. The above equations, however, are readily extended to nickel and nickel/copper mattes for any desired end product composition."

Jan 1, 1996

By Sergio N. Monteiro

From the leaves of the sisal plant (Agave sisilana) a relatively strong fiber can be extracted and is nowadays being investigated as a possible reinforcement for polymeric matrix composites. For this purpose, it is important to determine the critical length of the fiber with respect to the matrix to be reinforced. This has never been properly done for sisal fibers in polyester matrix. Therefore, this work characterized the critical length of sisal fibers, with different sizes, embedded in polyester capsules by means of pullout tests. The critical length obtained allowed the sisal fiber/polyester matrix interface shear stress to be calculated. The relevance of these values for polyester composites reinforcement with sisal fibers is discussed.

Jan 1, 2009

By S. Y. Tan

As continual complementary metal?oxide?semiconductor (CMOS) scaling requirements, metal gate/high-k dielectric/Si gate stacks are expected to replace poly-Si/SiO2/Si gate stacks in the future CMOS sub-45 nm technology node. Hafnium based oxide is a promising candidate to replace SiO2 as a gate dielectric, due to its much higher dielectric constant (high-k) and stability. The key challenges of successfully adopting the high-k dielectric/Si gate stack into advanced CMOS technology mostly come from the interfacial properties. The origins of the electrical and physical characteristics of the dielectric oxide/bulk interface were studied in detail. The leakage current density-voltage (J-V) and capacitance-voltage (C-V) measurement techniques were employed to study the dielectric oxide/Si interface. The effects of the post-deposition annealing (PDA) treatment on the interface charges of dielectric oxides were studied. We found that the PDA can effectively reduce the trapping density and leakage current, and eliminate hysteresis in the C?V curves. Besides, the changes in chemical bonding features at HfO2/Si, HfSiO/Si and HfSiON/Si interfaces due to PDA treatment were evaluated by XPS measurements. The XPS analysis provides a better interpretation of the electrical outcomes. As a result, both HfSiO and HfSiON films have exhibited superior performance in terms of thermal stability and electrical characteristics.

Jan 1, 2010

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010

By J .. R. Brown, G. Deschenes

X-ray Photoelectron Spectroscopy (XPS), X-ray Diffraction (XRD) and Electron Probe Micro-Analysis (EPMA) were used to characterize chemically the gold complex adsorbed on activatedcarbon from a solution containing 102mglL Au and 0.5 giL thiourea. This paper also considers the gold chloride and the gold cyanide systems. The results indicate gold is adsorbed on activated carbon from the thiourea solution as the gold (I) thiourea complex, i.e. Au [CS (NH) 2];' Other gold species such as metallic gold were not detected on the carbon support. These results also suggest the elution of the gold (I) thiourea complex can be performed with high recovery.

Jan 1, 1993

By C. L. Schneider

The problem of predicting the liberation spectra produced by a closed continuous grinding circuit is of fundamental importance for the design, optimization and control of most operations in an ore dressing plant. The only known approach through which such a calculation can be performed is the population balance model equation. The latest and certainly most significant progress made in this area is the solution proposed by King (1990), which requires one textural parameter that can be measured directly from the ore being studied. The main advantage of King's solution is that it does not require the estimation of hundreds of arbitrary parameters that cannot be independently measured, as required by the existing conventional solutions. However, King's solution relies heavily on a knowledge of the detailed internal structure of the Andrews-Milm diagram (Andrews and Mika, 1975). This has never been measured for any ore. The characterization of the internal structure of the Andrews-Mika diagram requires the measurement of the liberation spectra at several progeny sizes produced by the breakage of monosize, monograde particles at several different grades. In this paper, a procedure based on magnetic fluid fractionation for generating seven narrow-size, narrow-grade samples is presented. Each of these samples was then broken into six progeny size classes in an ultrasonic mill. The one-dimensional liberation spectra of each of the 42 progeny and seven parent particle samples were then measured by image analysis. The measured linear-grade distributions are presented in this paper. The calculation of the correspondent volumetric-grade distributions is discussed.

Jan 1, 1994

By T. T. Chen

The iron- and elemental sulphur-rich residues generated during batch and continuous pressure oxidative leaching of Inco Limited's Voisey's Bay nickel sulphide concentrate at 150°C in sulphate-chloride media have been characterized by X-ray diffraction analysis and scanning electron microscopy. The residues produced during the continuous leaching of the pentlandite- and pyrrhotite-rich concentrate consisted predominantly of hematite and elemental sulphur, with minor amounts of goethite. Although the iron species generated in the batch leaching tests were similar to those formed during continuous leaching, the morphologies of the hematite and goethite particles were significantly different. In addition to the tiny spheroids and bubble-like particles, the hematite and goethite generated during batch leaching occurred as larger "hollow" shell-like particles that contained residual pentlandite or sulphur cores. Although the leach solution from which the iron oxides had precipitated contained 5-15 g/L sodium, sodium jarosite was detected only in trace amounts in a few of the leach residues.

Jan 1, 2006

By J. Roodt

Paper written on project work carried out in partial fulfilment of B. Eng (Metallurgical Engineering) degree This work was done to characterize the leaching of a uranium containing pulp processed by a South African producer to identify parameters that could be adjusted to increase the extraction of uranium in the existing circuit. Batch leach tests were used to characterize the leach properties and especially the influence of the oxidant concentration on the leaching achieved. It was found that relatively high extraction could be obtained even at room temperature by using a high liquid-to-solids ratio and that increasing the oxidant concentration significantly improved the leaching of the uranium minerals.

Jan 1, 2003