Search Documents

By Ronald D. Hill, Elmore C. Grim

Coal-haul and mine access roads are defined as any road constructed, improved or used by the operator (except public roads) that ends at the pit or bench. These roads constitute approximately 10% of the total area directly disturbed by the surface mining operation(l). In some cases, the land disturbed by haul roads exceeds the area included in the mining operation. Studies (2 and 3) of the U. S. Forest Service in eastern Kentucky show that typical contour mining roads exhibit poor alignment, excessive grades, insufficient strength and durability, and poor drainage. Mine roads in other Appalachian- States, particularly where contour mining is practiced, appear much the same as those in Kentucky. Access roads(4) were also found to be a large source of sediment. It is possible that of the sediment that finds its way into the streams as much (or even more) originates from the haul roads as from the mining operation. Most roads are built as cheaply as possible, and good road-building design and practice are ignored. Maintenance schedules are generally inadequate, and upon completion of mining, haul roads are usually abandoned, with little or no attempt made to bed them down(5 ) . Such roads deteriorate very rapidly (Figure 68). Area mining, which is practiced in flat to gently rolling terrain, presents fewer haul road related environmental problems. These roads through necessity are generally well engineered because of the heavy equipment using them, such as 240 ton (217 metric ton) haul trucks. They must have wide beds, good alignment, and adequate drainage to permit coal haulers to run at top speed during all seasons of the year. Excessive dust can be a public nuisance and a driving hazard, and it is hard on equipment. Calcium chloride and sodium chloride have proven to be effective materials for controlling dust. Two applications during the summer when the ground surface is moist at the rate of 1/2 pound per square yard (.26 kilograms per square meter) (3 1 have been suggested. Th4 most common procedure is to keep the roads wet by using water trucks. Sediment that reaches the streams can be traced to one or more of the following five basic phases of haul-road life:

Jan 1, 1974

By W. W. Adams

In mining coal, the Nation's principal mineral fuel, loss of life has been much lower recently than in earlier years when coal mining contributed so heavily to the industrial-accident death toll in the United States. Particularly notable has been the relatively small number of deaths during the past few years compared with the number that occurred 20 or 30 years ago. Reports received by the United States Bureau of Mines, covering all commercially operated mines that were active during all or any part of the calendar year 1935, showed that accidents during that year had resulted in the loss of 1,242 lives. This death toll, although regrettable, represents a material improvement over the industry's experience during most years prior to 1935, and especially over the industry's worst year, 1907, when 3,242 men were killed. Fewer lives were lost in 1933, when 1,064 men were killed at work, than during any year for which complete figures are available.

Jan 1, 1938

By W. W. Adams

The accident-prevention record of the coal-mining industry in the United States was more favorable in 1936 than in 1935, both from the standpoint of the relative safety of the individual miner on the job and of the price in life and limb that the Nation paid for its year's supply of coal. The increase in relative safety of the individual miner was indicated by a lower death rate and a lower injury rate than in the preceding year per million man-hours of exposure to the hazards of mining; that is, per million hours of work performed by the employees. (See table 1.) A reduction in the price in life and limb that the Nation paid for a year's supply of coal was indicated by a smaller death rate and a smaller injury rate per million tons of coal produced. Thus the individual miner was a better insurance risk, as far as accidents were concerned, in 1936 than in 1935, and a ton of coal used in the homes and industries of the country represented less human suffering than in 1935. The two points of view are distinct, and both should be kept in mind when considering accidents and safety in coal mining or in other industries. More men were employed in 1936 than in 1935, and more workdays were available for the individual miner. Large gains were also made in the total number of man-shifts and man-hours worked in the industry as a whole. In number of tons of coal mined, 1936 showed large gains over 1935. Moreover, the average output of coal per man-hour worked was higher in 1936 than in 1935. All of these gains were made without lengthening the average number of hours of work per man per day.

Jan 1, 1939

By W. W. Adams

Coal mining in the United States, had a somewhat higher death rate per million man-hours of exposure among the employees in 1937 than in 1933 to 1936. However, the rate in 1937 was lower and therefore more favorable than that in any year since 1921 but previous to 1933. The nonfatal injury record, which began in 1930, was lower and therefore better in 1937 than in any other year since 1930. Separate figures covering bituminous-coal mines in all States showed a lower fatality rate in 1937 than in any year since 1920 but before 1933, and a lower nonfatal injury rate than that of any year since 1930 except 1933 and 1936. Reports for anthracite mines in Pennsylvania revealed a better safety record for fatal accidents in 1937 than in any year since 1930 except 1933, 1934, and 1936 and a better record for nonfatal injuries than in any year since 1930 except 1933.

Jan 1, 1940

By W. W. Adams

Every man-hour of work performed in and about the coal mines of the United States had a 2-percent heavier death load from accidents in 1938 than in 1937. This is an unorthodox way of stating that the death rate per million man-hours of exposure or employment was 2 percent higher in 1938 than in 1937, increasing from 1.74 to 1.78. Thus the average miner had a 2-percent greater chance of being killed in 1938 than he had in 1937. The average quantity of coal resulting from 1 man-hour of work increased 3.6 percent -from 0.615 ton in 1937 to 0.637 ton in 1938. The production of the average ton of coal was accompanied by a slightly smaller loss of life in 1938 than in 1937, the accident rate being 2.793 per million tons in 1938 compared with 2.833 in 1937.

Jan 1, 1941

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By W. W. Adams

With production of coal per man-hour of work highest in history, the coal mines of the United States established a lower accident-frequency4 rate in 1942 than in any year since 1930, the first for which the Bureau of Mines, United States Department of the Interior, collected complete reports of nonfatal as well as fatal injuries. Reports from mine operators and State mining departments showed that 530,861 men were employed in and about coal mines during the calendar year 1942. This number does not include office employees or coke-oven workers. The figure represents a decrease of 15,831 men from the previous year, owing to losses of men to the military services and to more lucrative employment in the munitions and other industries. The loss of men was offset to some degree by an increase in the number of days of mine activity and the average number of hours of work per man during the year. The volume of work done during 1942 was 910 million man-hours, 11 percent more than in 1941. The average employee worked 243 days, 30 days more than in 1941. Production reached the unprecedented total of 640 million short tons, an increase of 12 percent over 1941; 582 million tons came from the bituminous fields of the United States and 58 million tons from the anthracite fields of Pennsylvania. To produce this quantity of coal 1,471 men sacrified their lives, and 69,564 men suffered nonfatal injuries that disabled them for more than the remainder of the day on which the accident occurred. The nonfatal injuries were divided into three groups: 65 caused permanent total disability, 2,045 caused permanent partial disability, and 67,454 caused temporary disability of 1 day or more but did not result in the loss of, or permanent loss of use of, any part of the body.

Jan 1, 1944

By W. W. Adams

The safety record established by the coal-mining industry of the United States during 1934, although not as favorable as that for the previous year, was better than the record for any other year during the period 1930-34 for which complete figures covering fatal and nonfatal accidents at the mines are available. The number of accidents was 89.98 per million man-hours of employment compared with 86.74 for the year 1933, the latter being the lowest rate in any of the 5 years referred to. The rate was 105.60 for 1930, the first year covered by available data. Employment increased in 1934; the number of workers represented an increase of 8 percent over the year 1933, man-shifts of labor increased 16 percent, and the number of man-hours of labor increased 7 percent. The total number of man-hours of employment also exceeded the number reported for 1932, and was almost equal to the record for 1931.

Jan 1, 1936

By W. W. Adams

With production of coal per man-hour of work at a higher level than ever before, the coal-mining industry of the United States established a near-record in lowering the accident rate of nonfatal injuries per million man-hours of exposure in 1940, the injury rate being lower, except for 1939, than in any year since 1930, the first year for which comparable figures for nonfatal accidents were collected by the. Bureau of Mines, United States Department of the Interior. The rate for fatal accidents, on the other hand, was not as low or favorable as in 1939, nor was it as low as in many years since 1910, the earliest year for which fatality rates were complete for all coal-mining States. Accident and employment reports received from mine operators and fatal-accident reports from State mining departments and inspectors showed that 533,267 men were employed at coal mules in 1940, exclusive of the number employed at coke ovens, Although this number represented 6,108 fewer employees than in 1939, a large increase was made in the volume of work performed and in the quan¬tity of coal produced. In 1940 the amount of labor performed at coal mines was 748 million man-hours, a gain of more than 10 percent over the previous year. The average employee worked 199 days, an increase of 20 workdays per man. Production of coal was nearly 513 million tons, an increase of 14 percent, of which more than 461 million tons was bituminous coal and more than 51 million tons was Pennsylvania anthracite. Accidents to mine workers caused the death of 1,388 employees; in addition, 59,781 employees were injured, and each injury resulted in disability of the employee for more than the remainder of the day on which the accident occurred.

Jan 1, 1942

By W. W. Adams

With greater production of coal per man-hour of work than ever before achieved, the coal-mining industry of the United States established a better safety record in 1941 than in any year since 1930, the earliest for which complete reports of nonfatal as well as fatal injuries were collected by the Bureau of Mines, United States Department of the Interior. In only one year (1933) of the 12-year period 1930-41 was the fatal-accident rate better than in 1941, whereas the rate for nonfatal accidents was better in 1941 than in any previous year. Accident and employment reports received from mine operators, together with fatal-accident reports received monthly from State mining departments and inspectors, showed that 546,692 men were employed in and about the coal mines of the United States during the calendar year 1941. This number does not include office employees or coke-oven workers. The increase of 1.3,426 over the number of employees in 1940 was accompanied by a gain in man-hours of work performed at the mines and an increase in average number of hours worked per man during the year.

Jan 1, 1944

By Charles T. Holland

ANALYSIS of 117 occurrences of bumps in coal mines shows that 67.6 percent are associated with pillar-line points.4 Slabbing and splitting pillars, development, and other unfavorable milling practices in abutment areas may be a contributory or the primary cause of bumps. The cure for pillar-line bumps is to recognize areas that can be expected to become highly stressed and to project the mining plan and operations to eliminate such areas insofar as possible. If such areas cannot be eliminated, then the mining plan and operations should be projected to avoid the necessity of disturbing these areas before the stresses have been dissipated.

Jan 1, 1954

By H. N. Eavenson

In a discussion in the Transactions of the Institute (vol. Xl, page 835 et seq.) the writer gave some data about the explosions of gas and dust in the coal mines of the United States, Canada, and Mexico…

Jan 1, 1915

Discussion of the paper of HOWARD N. EAVENSON, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October,' 1914, pp. 2637 to 2660. GEORGE S. RICE, Pittsburgh, Pa.-I think it is very wise to point out the greater liability to explosions in certain parts of the year, if there be such difference, with the caution, however, that vigilance be not relaxed at other times. In comparing the figures for the United States with those of Europe, I think we should separate them as far as possible according to cause of origin and means of propagation. That is to say, it would appear to me that the majority of our explosions are due more directly to the ignition of coal dust directly from the flame of explosives, whereas, judging from my inquiries and observations in some of the mines of Europe, the majority of their explosions have been caused by the ignition of fire damp. Now, in the case of fire damp, I do not think that anybody has yet attempted or has been able to find any connection between the seasons and the issuance of methane into mines. One thing must be borne in mind, that if you get a strong explosion of fire damp, dust of a character that might not ignite readily by itself might assist in the extension of an explosion of fire damp through a considerable area in the mine, if not throughout the mine. While it is true we have many lesser explosions in this country attributable to fire damp, it would appear that the majority of all the mine explosions of the country, in considering the means of propagation beyond the locality of the origin, are due to coal dust; and it is the liability to coal-dust explosions that appears to be affected by seasonal changes. Hence the desirability of separating statistically (if it could be done by the inspectors) fire-damp explosions from coal-dust explosions, in order to obtain the true value of the seasonal effect. Nevertheless, in spite of the inclusion of fire-damp explosions with coal-dust explosions, the preponderance of the evidence, as indicated in Mr. Eavenson's figures for American mines, has shown that' in this country there were more explosions in the winter and spring months, when the mines are drier; that is, when the mines are apt to be drier. Whereas, according to the European figures that he has gathered, it seems to be very clearly demonstrated that in France, England, and Belgium, the time when explosions occur has no connection with any particular season. That, I think, is partly due to the point just mentioned, that a majority of their explosions have originated from fire damp. The European mining men have been more careful, generally speaking, with the use of explosives than we have, so that the cause of ignition from that source has been less. Only comparatively few of the mines in foreign

Jan 4, 1915

By Howard Eavenson

IN a discussion in the Transactions of the Institute (vol. xl, page 835 et seq.) the writer gave some data about explosions of gas and dust in the coal mines of the United States, Canada, and Mexico, among which was a table showing all explosions in the countries mentioned, in which five or more fatalities occurred, which had been reported from Oct. 2, 1871, to Mar. 28, 1908. Since the elate of publication of this discussion, as opportunity has presented, this table has been extended by the addition of explosions occurring since that time, by including several explosions which occurred prior to 1871, and by adding to the list all explosions of gas or dust in which less than five fatalities occurred, this having been clone by a search through the various mine reports, partly by the author and partly by the Librarian of the United Engineering Societies, and by correspondence with mine inspection officials of the various States, to all of whom acknowledgment of assistance is made: The accompanying list, Table I, is believed to be as nearly correct as such a statement can be made, and, while only extending to Dec. 20, 1912, contains all of the data now available in reports. An analysis of Table I, showing the occurrence by months of all explosions of gas or dust, including those in which less as well as those in which more than five fatalities occurred, is given in Table II. The statements are frequently made, in technical papers, that the number of explosions, particularly the larger ones, is increasing more rapidly than the number of mines, and that the number of fatalities caused by mine explosions, particularly the more disastrous ones, is increasing faster, proportionally, than the production of coal. To investigate the correctness of these statements Table III was prepared, in which the number of accidents and fatalities is taken from Table I, using those in the United States only, on account of lack of other data for Canada and Mexico; the production is from the records of the U.S. Geological Survey, and the number of mines, from 1909, from the same source; previous to 1909, the number of mines, for the decennial periods, was furnished by the U. S. Census records.

Jan 10, 1914

By J. L. CAHUTHERS

MANY different methods are used for transporting coal from the working face to the tipple. The common methods are animal haulage, locomotive haulage, conveyor systems, and combinations of these three, supplemented, at times, by the miner pushing his own car. Haulage may also be classified into gathering and main line. Gathering haulage is the collecting of loaded cars to a point whence they are hauled to the tipple. In this there is perhaps more lost-time than on the main line because there are .more units in the operation to be synchronized. Also, conditions on the gathering haul- age, such as bad track, poor timbering, insufficient motive power, etc., cause delays; usually these are corrected on the main-line haulage.

Jan 1, 1931

By Alex Hay

THE Sydney coal field, the largest and most valuable in Nova Scotia, is situated on the northeastern coast of the Island of Cape Breton, extending from Mira Bay on the south to Cape Dauphin on the north, a distance of 30 miles, and has a general dip northeast under the sea. (Fig. 1.) The field embraces the mining villages of Morien, Birchgrove and Reserve and the towns of Dominion, Glace Bay, Waterford and Sydney Mines. The city of Sydney is situated about midway between the northern and southern extremities of the field and on the western fringe of the productive coal measures. Sydney harbor crosses the coal field, cutting off direct rail connection between Sydney Mines and the greater part of the field to the southeast. (Fig. 2.) The coal measures are exposed in the cliffs on the coast line, which rise to an average height of 30 ft., and are almost continuous throughout the length of the field. The portion of the coal field under land forms a small segment of a circle, the greatest distance from the coast landwards is 9 miles, and it occupies an area of 200 sq. miles. The greatest distance developed seawards from the shore by mining operations is 2 ¼ miles. The strata maintain a regularity of dip at this distance, proving a submarine area of about 70 sq. miles. How much further the coal field extends seawards is unknown, but the indications are that it extends far beyond the present economical working limit and in all probability there is a vast submarine coal field. The productive coal measures are of Carboniferous age, these being underlaid by beds of sandstone, locally classed as millstone grit, which define the southern limit of the field,, while a spur of syenitic hills cuts off the coal-bearing strata on the north. Two main anticlinal folds having a general course easterly divide the field into three basins named from north to south: Sydney Mines-Lingan, Glace Bay and Morien.

Jan 1, 1929

By George S. Rice

INTERESTING developments going on in European coal mines look to: (1) increasing mechanization; 12) concentration of mining; (3) improvement in safety appliances; and (4) studies in bettering roof supports and. incident to this, studies of the way a roof behaves under different conditions of support and methods of mining and back-filling. Mechanization and concentration off mining is being adapted to a considerable extent in Great Britain coincident with the development of conveyors. Belt conveyors, shaker-pan conveyors, and a combination of the two are used. For pitching seams not steep enough for the coal to run in station-chutes, the. shaker-pan conveyor is more popular. For large outputs from a contiguous face, the double-unit system of face layout-that is, the conveyors meeting at a common point-is favored.

Jan 1, 1934

By George Watkin Evans

The United States Geological Survey has estimated 1 that the State of Washington contains 11,412,000,000 tons of bituminous coal and 52,442,000,000 tons of subbituminous coal, in beds more than 14 inches thick. As the present rate of production is about 4,000,000 tons a year, Washington apparently contains coal enough to supply Pacific coast markets for many years. The character of the coal beds of Washington renders the production of clean coal very difficult, and a considerable proportion of the output is washed before it is marketed. In 1915 Washington ranked fifth among the States in the amount of coal washed, though only twentieth in total output. In that year 37.9 per cent of the coal produced in the State was treated in surface cleaning plants.

Jan 1, 1924

By D. R. Hardman

South Africa is the third-largest supplier of coal on the world's export markets after Australia and the USA, and the second-largest supplier of bituminous steam coal following Australia. There are many Similarities between the coal industries of South Africa and those of Australia and the USA, in contrast to the coal industries in Europe. For South Africa to maintain a competitive position on the export markets, it must continue to compete against these two countries. It is therefore important that the performance of the loca1 coal industry should against that of the Australian and US coal industries. Although financial performance is the major criterion, financial information is not easily obtained, and the paper therefore uses employee productivity in the form of tonnes per man year as a means of comparison. The paper reviews recent trends in the level of production and numbers of employees prior to review1ng the productivity. The influence on productivity of some mining methods is highlighted. It is realized that published information (information available within the public domain) can contain anomalies, but every effort is made to compare data of a similar type. Notwithstanding possible inaccuracies, it is shown that South African coal-De productivity lags far behind that of Australia and the USA. The significance of the difference is that the South African coal industry is able to apply overseas practices and procedures that have been shown to give improved performance, and that the increased use of more productive extraction techniques has limited application.

Jan 1, 1996

By Kristineq Pankow

The August 2007 Crandall Canyon mine disaster raised national awareness of mining-induced seismicity (MIS) in Utah as well as general interest in how seismic monitoring might improve mine safety in the region. Unlike the situation in most other mining areas in the U.S., local seismographs in Utah?s Wasatch Plateau (WP) and Book Cliffs (BC) coal fields are an integral part of a modern real-time earthquake information system developed by the University of Utah Seismograph Stations (UUSS) as part of an Advanced National Seismic System. The UUSS earthquake catalog contains a continuous record of MIS at all active mine sites in the WP-BC region since 1978 (more than 18,000 seismic events = M 4.2). We describe characteristics of MIS and current seismic monitoring capabilities in the WP-BC region. We then demonstrate, using MIS from an example Utah coal mine, the ability to refine event locations with estimated absolute errors of ~200 m or less using a combination of (1) a double-difference relocation methodology and (2) ground truth information provided by mine operators. This approach enables sufficient spatial resolution to correlate MIS with mining activities, providing a useful tool to help improve mine safety.

Jan 1, 2008