Search Documents

By R. C. Rastogi, F. F. Aplan

The goal of this study is to evaluate the coal flotation process and the interaction of the chemical (reagent) and hydrodynamic (machine, operational) variables as they affect yield, flotation of various sized particles, and sulfur and ash rejection. Coal flotation is found to follow a first order process with the coal floating much faster than either pyrite or ash. This circumstance may be used to achieve gangue rejection during flotation. When floated with MZBC, cresol, or pine oil frothers, coal floats in the size sequence: 108 pm ( - 65 mesh), 589 x 808 pm (88 x 65 mesh), and 1.17 mm x: 589 pm (14 x 18 mesh). However with a substantial amount of fuel oil collector, all particles tend to float roughly in proportion to their content in the feed. An increasing aeration rate was found to be the most important variable in increasing the coal flotation rate. This increase in flotation rate, unfortunately, is also accompanied by an increase in the flotation rate of the pyrite. The rejection of pyrite during coal flotation is best accomplished at low aeration rates, low frother concentrations, and low impeller speeds.

Jan 1, 1986

By A. V. Nguye, P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration. Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. A possible mechanism, based on the existence of the pre-existing submicron-sized gas bubbles, known as bubstons (i.e. bubbles stabilized by ions), present in water in close proximity to the hydrophobic coal surfaces is discussed in line with the early observation of flotation improvements by microbubbles “nucleating” on hydrophobic surfaces. In particular, the dependence of the bubble-particle attachment efficiency on electrolyte concentrations supports hypothesis on the salt-dependent and ion-specific existence of bubstons. However, a theoretical explanation of the transition salt concentration (at about 0.1M) is deficient at present. The existence of these submicrobubbles in close proximity to hydrophobic surfaces is not trivial. They can (as can individual gas molecules or other solutes) mediate and extend the range and magnitude of the attraction between hydrophobic macroscopic surfaces. These bubbstons may explain the curious phenomena of the socalled long-ranged hydrophobic attraction measured with the Surface Force Apparatus and Atomic Force Microscopy, and the slippage at hydrophobic surfaces. Finally, the coalescence of bubbstons affects the rupture of liquid films at a very large thickness (over 100 nm), observed, but unexpected, by flotation chemists.

Jan 1, 2003

By P. A. Harvey

Previous studies have reported that inorganic electrolytes can enhance floatability of coal. The research has shown that the enhancement, if any, is highly dependent on changes in solution pH, type of electrolyte, and electrolyte concentration. The reasons for this are still not clear. In this study the floatability of coal particles in mono and divalent salt solutions was investigated. The zeta potential and hydrophobicity of the coal was measured experimentally, and a modified Hallimond tube was used to determine the floatability of coal particles by single bubbles, where the collision efficiency was equal to unity. The experimental information was used in conjunction with the Hogg-Healy-Fuerstenau equation to quantify the electrical double layer interaction. It was found that for low electrolyte concentration (less than 0.1 M) solutions the flotation recovery of coal particles was less than that for distilled water, and decreased with increase in concentration. Conversely, at electrolyte concentrations above 0.1 M, flotation recovery increased with increasing concentration (Figure 1). Both of these results are consistent with previous observations, but are inconsistent with expectations when considering the possible influence of electrical double layer interaction. Modelling of the system indicates that the electrical double layer is compressed with increasing electrolyte concentration, resulting in an increase in flotation recovery due to a diminishing of the (electrical double layer) repulsion between the bubble and the coal particles. Moreover, for electrolyte concentrations above about 0.1 M the electrical double layer is completely depressed and would have little further influence, if any, on the flotation process. Therefore, the electrical double layer interaction is not the principal determining factor for the flotation of coal in electrolyte solutions.

Jan 1, 2003

By S. C. Sun

[There are significant quantities of anthracite silt deposits in Pennsylvania, known as 'liver silts" (l,2). These contain from 20 to 55 per cent of non-combustible materials, the major portion of these impurities being clay slimes. Both the anthracite coal and impurities are mostly of extremely fine particle size. The utilization of these raw silts in power-plants faces such serious problems as, handling difficulties causing plug-up in equipment, disposal of enormous ash-residue, and corrosion. These problems may be solved by upgrading the raw silt with a cleaning process, which will be capable of removing most of the clay slimes and electrolytes.]

Jan 1, 1964

By W. Irwin

As a consequence of the oil crisis of the 70?s, the commercial value of coal increased very sharply and an upward trend in coal prices although now less pronounced, continues today. The graph shown in figure 1 illustrates the trend in the F.O.B. price of U.S. metallurgical coal. This trend occurs during a time when mechanized mining is firmly established as a means of production throughout the coal mining world. With modem methods of mining, mechanical cleaning is a necessity and quality control is no longer entirely dependant upon coal face practice. The efficiency of fine coal recovery is of vital economic importance to present day operations and good practice in this field contributes significantly to improving profitability. Numerous processes are available for the duty and this paper discusses one such system, namely the practice of froth flotation.

Jan 1, 1980

By G. H. Harris

The flotation behavior of two high sulfur coals using a non-ionic surfactant as collector from two series of compounds containing oxygenated functional groups was studied in detail using a 2-liter Denver flotation cell. The performance of these reagents was compared with that of an oily collector, namely dodecane. The results showed that at the same coal recovery, a much lower dosage of these non-ionic surfactants was required as compared with that of dodecane. More import was the performance of these compounds as promoters for oxidized as well as un oxidized coal. Mechanisms of interaction of these compounds with the coal are suggested.

Jan 1, 1993

By R. A. Seitz

This paper presents a framework for analyzing the theory and industrial practice of coal flotation and gives some examples of its use for understanding flotation phenomena and optimizing/controlling flotation circuit performance. It is based on extensive laboratory and in plant test work conducted over the past several years by researchers at MTU as well as an analysis of the literature. Previous researchers have usually considered either the surface chemistry or the kinetics of coal flotation behavior, only rarely have these factors been considered together. However, these factors must be considered together in order to gain a clear understanding of the theory underlying coal flotation such that its practical application can be optimized. Fortunately, this complex objective can be achieved by considering the recovery and rate of recovery of the different types of particles present in the feed to coal flotation circuits and the fundamental mechanisms responsible for these recovery phenomena. The influence of three major groups of variables must be considered: control variables (reagent additions, aeration rate, etc.); disturbance variables (feed pH, percent solids, etc.); and circuit design variables (number of cells, circuit arrangement, etc.). Each of these groups of variables affects process kinetics in a clearly understandable manner, which, once determined, is extremely useful in circuit design and optimization. This paper includes a discussion of the use of the proposed framework to explain the effects of some coal characteristics on flotation performance. In addition, an example of using this analysis to optimize the performance of a coal flotation circuit using frother and collector addition levels is included.

Jan 1, 1985

By E. G. Bailey

PLANTS that normally burn coal now able too obtain a substantial increase over their normal supply for their greater power needs, and also additional tonnage for extra storage against the uncertainties of the future. Many plants previously burning oil or gas have already been converted to coal, and those which must yet change to coal will undoubtedly be able to obtain ample tonnage of coal of standard quality at reasonable prices. What a contrast this is to the conditions of 25 years ago, when the shortage of coal and transportation led to prices of $5 to $6 per ton at the mines, and degradation of quality, until the already overburdened railroads were called upon to haul 100,000 ton per day of extra ash alone. This was the result of a runaway market and the loading of gob, slate, and sub-quality coal amounting to an estimated increase in ash of 5 per cent of the total tonnage hauled. The problem of getting increased steam output from inferior coal caused unbelievable reductions in the low normal boiler efficiency of that time and untold labor in firing the hand- and stoker-fed furnaces of that day.

Jan 1, 1942

By Scaife PH, Cripps Clark J, Cameron DB

Tuyere coke samples have been taken through the tuyere openings of B.H.P. International Blast Furnaces since 1978 with Whyalla No. 2 Blast Furnace taking samples on a regular basis since 1982. The degradation of coke during it's passage through the Blast Furnace can be measured and the relationships between these data, feed coke data and blast furnace operating data demonstrated. Tuyere coke sampling has been useful in revealing misleading external coke testing results and is still the method to monitor directly the performance of coke within the Blast Furnace.

Jan 1, 1987

The known coal resources of South Australia are either of poor quality, or expensive to extract, or both. Export quality coal occurs only at great depth in the remote north of the State; the balance of the State's coal resources are suitable only for local electricity generation. Currently there is only one coal mine in the State, at Leigh Creek. This provides fuel for approximately 34% of the State's electricity generation, the balance being fuelled by natural gas. In the near future, new fuel sources must be developed to augment diminishing supplies of natural gas, and to cater for increasing demands for electricity. The South Australian Government has determined that future electricity generation will be based on the combustion of local coals. The geological and geographical environment of the known coal deposits and the quality of these coals are such that the most up to date and innovative technology must be applied to both extraction and combustion processes. The Government, the Electricity Trust of South Australia, and several Australian and overseas companies have embarked on an extensive research and development programme to ensure that these otherwise useless resources can be developed to the benefit of the State.

Jan 1, 1987

By Bret K. Clayton

Jan 1, 2004

By A. Wahab Khair, Richard D. Begley

"This paper presents results of destructive tests performed on rectangular coal specimen under the influence of two vertical and simultaneous wedge indentation forces. Several wedge designs and spacings were utilized in compression tests. The objective of these experiments was to qualitatively monitor the effect of different wedge designs and spacings on the stress distribution within the coal specimen.Coal samples from the Waynesburg coal seam were cut and trimmed to cubical dimensions of approximately 5 X 10 X 20 cm. These specimen were subjected to parallel compressive forces through two vertically applied wedge indentors. Loading was achieved with a hydraulic hand pump in order to facilitate interferogram construction. The load increments were limited due to the sensitivity of the holographic interferometric technique (holometry) in measuring small displacements; therefore, interferograms were taken only during similar increments in order to allow for a qualitative comparison between different wedge design and spacings. In some cases, interferograms were taken immediately before and after failure of the specimen.Introduction Failure Modes Three distinct modes of failure occur when geologic materials are subjected to wedge indentation forces. As shown in Figure 1, a crushed zone is located immediately adjacent to the indentor while chipping can occur if the fractures initiated in the crushed zone extend upwards to the free surface.. The third failure mode is a zone of intricate frac¬tures located between the crushed zone and the chipping zone. Several experiments have been conducted over the years to better understand crater formation and stress distribution within geologic materials under the influence of an indentor. Generally speaking, crack initiation and propogation observed in these experi¬ments correlate fairly well with wedge indentation theory; however, the nature of the .fractures is greatly influenced by different material properties such as grain size and cleavage planes. In other words, a wide range of behavior has been found in different rocks subjected to wedge penetration. For example, it has been observed that some rocks are merely crushed and indented while others are more prone to cracking and chip formation. Therefore, the development or nondevelopment of chips depends mostly on wedge geometry, rock type and depth of penetration. This work is part of the study associated with opti¬mization of cutting parameters, which is best modeled by using brittle materials and subjecting them to rigid wedge penetration tests."

Jun 1, 1988

By Robert D. Hansen, Richard R. Klimpel

INTRODUCTION A very important factor in froth flotation is the use of surface-active chemicals to form a froth in which minerals or coals are retained, thus allowing for valuable component enrichment. In coal flotation reagents (frothers) specifically designed to provide an efficient froth are employed. It is this group of chemicals that will be the primary emphasis of this paper. Despite the importance of frothers, surprisingly little systematic scientific work has been performed with the goal of quantifying frother mechanisms and the influence of particles on froth stability. Based on direct experimental observations in both batch laboratory and continuous large-scale flotation cells, the use of a frother significantly increases first, the possibility of a particle- bubble contact, and second, the efficiency of sticking after such a contact. Thus, a major role of a frother is to significantly increase the rate of flotation. This rate modification by a surface-active agent occurs through several observable mechanisms including the formation of a froth of relatively consistent character (bubble size and bubble density) under a variety of operational conditions, an increase in the ability to disperse air in the flotation cell, a reduction in the rate of coalescence of individual bubbles in the cell, and a decrease in the rate of bubble rise to the pulp surface. It will not be the intention of this paper to exhaustively list all frother accomplishments related to research, development and use in coal flotation. Rather, the authors will attempt, based on their experience, to present a technology overview of the role of frothers in the chemistry of flotation as successfully practiced at the industrial level. A very useful framework for flotation is the concept suggested by Klimpel (1984, 1984a) of viewing flotation as a system consisting of three major components: chemistry, equipment and operating variables. This is illustrated in Figure 1. A major point of this figure is that flotation is a highly interactive system with many technical and economic combinations of component settings available to operators to achieve a given goal. Sometimes simultaneously changing various component settings will reinforce a particular attribute. Also various component settings can cancel or counteract each other if changes are not chosen wisely. Thus, coal flotation must be viewed by the plant operator as a complex system with the economic/technical optimization of a given flotation process being directly related to the operator's knowledge of how his particular flotation system behaves as a function of the major control variables he has at his disposal. Typical important component settings in coal flotation are collector dosage, frother type and dosage, air flow rate, feed rate, particle size, pulp density, and the surface oxidation conditions of the coal. Because of the above complexities, it is sometimes assumed (especially in laboratory studies) that the choice of frother type and dosage is not as crucial as some of the other factors such as collector type and dosage (e.g., Leja, 1982). Detailed plant level testing of all of the factors of Figure 1 performed in recent years, Klimpel (1980, 1980a, 1982, 1984, 1984a), Hansen (19861, Klimpel, Hansen and Meyer (1982), simply do not support this assumption. The above testing has shown rather clearly that certain frother chemical structures consistently exhibit predictable performance characteristics in both mineral and coal flotation. In addition, significant changes in both rate and recovery can be expected. In the remaining sections of this paper, the following topics will be covered: requirements of chemicals capable of use as frothers, types of chemicals used commercially as frothers, some general performance characteristics of existing commercial frothers, and recent work in developing new frother chemical structures.

Jan 1, 1986

By J H. Dressel, J. E. Williams

This paper presents a brief review of what coal gasification is, procedures that are available today and processes that may be available in the future. Examples are given as to how the process might be used in power plant applications, the effect on pollution level and power costs, and some thoughts on the added burden that might be placed on mining and coal preparation.

Jan 1, 1973

By Robert Sisselman

If we are lucky," says Hollis M. Dole, Assistant Secretary of the Interior, "coal, uranium and hydropower will provide us with maybe a third of the energy we require in 1985. The other two- thirds will have to be made available in liquid and gaseous form." Luck, however, may have run out, for if the facts and figures relating to supply and demand of natural gas over the next 20 years prove accurate, the United States may fall short in its attempts to bring the energy crisis under control. By the year 1990 the world will need to consume a minimum 150 quadrillion Btu of energy with gas requirements running as high as 42-43 trillion cu ft. By 1990, the U.S. alone will require 45-46 trillion cu ft. To meet anticipated demand, this country will have to overcome a deficiency of about 20 trillion cu ft since, by all pragmatic estimates, it will produce only 15-20 trillion cu ft of gas. The importation of natural gas into the U.S. will help but will not solve the problem. Adequate gas supplies will have to be supplied domestically. The Arctic, with its predicted huge reserves of gas, combined with imports of liquid natural gas (LNG) may provide as much as 15% of the 45-46 trillion figure, however, such reserves will not come into play as quickly as originally thought. The Alaskan gas fields, for instance, will provide a substantial supplement to domestic gas needs, but only after 1976.

Jan 10, 1972

By T. D. Brown

"A review of the current status of gasification technology shows that many engineering systems are immediately available for use in the gasification of coal. Widespread international experience can be brought to bear on the atmospheric pressure gasification of all Canadian coals.Unless a high ash content dictates the use of a fluid-bed gasifier, it appears that bituminous coals can be used in gravitating (fixed] bed systems and that the strongly caking coals are most suited to the high-pressure entrained-bed systems . Existing and developing technologies in fluid-bed gasification are attractive for reactive lignites and subbituminous coals.The Fischer-Tropsch based process is the only commercial embodiment of coal liquefaction; the use of Canadian coals in this process depends only on their gasification characteristics. Current developments in hydroliquefaction are directed toward carboniferous coals of medium or high rank. It is not clear that cretaceous coals of the same rank will give similar process yields and economics.IntroductionThe twin coal conversion processes of gasification and liquefaction have a history which dates back beyond the current energy shortages of the western world. Indeed, liquids and gas from coal were produced before this century.Coal gas produced from a coal carbonization process was originated before 1800, and the development of gasification of non-coking coals was patented by Siemens in 1860.This patent represented the first use of air and steam together in the gasmaking process. The pioneering development of coal gasification Using oxygen and steam was demonstrated by Lurgi in the late 1920s. This historical sequence was all carried out at atmospheric pressure, and it was not until the immediate pre-war (1939/45) years that operation of the coal gasification process at elevated pressure became a reality."

Jan 1, 1981

By Henry R. Linden

The demand for natural gas continues to increase at higher than anticipated rates, partly because of its widening price advantage over most other fossil fuels when the cost of air pollution control is included. However, there are clear indications that natural gas supply from the contiguous 48 states and continental shelves will not indefinitely keep up with this rapid growth in demand. Projections are presented which define the extent of potential deficiencies from the 1970's to the year 2000. Among the sources of supplemental gas - imported pipeline natural gas from Canada and Mexico, tanker import of liquefied natural gas, and synthetic pipeline gas from coal and oil shale - by far the most abundant at potentially competitive costs is pipeline gas from coal. The state of development and relative economics of the various coal gasification processes are reviewed. It is shown that synthetic pipeline gas could become a very substantial market for bituminous coal and lignite at current minemouth prices - 60-70 million' tons of coal for each trillion cubic feet of synthetic pipeline gas produced. This corresponds to only slightly more than the current annual increase is gas demand.

Jan 1, 1969

By R. D. Merer

The production of low- and medium-Btu gas from coal provides a more economic source of energy for most industrial users than pipeline-quality coal gas (SNG), although the latter has received more publicity. The paper reviews existing and advanced methods of coal gasification, with particular emphasis on the production of low- and medium Btu gas for industrial and utility use. Some of the ways in which coal gasification can be integrated into power cycles and industrial plant energy balances are discussed.

Jan 1, 1978

By Hanna P

Coal geologists are under pressure to minimise exploration expenditure, maximise interpretation confidence and produce the results often too soon. This pressure continues to increase as companies are forced to evaluate borderline economic deposits which are usually deeper and more hazardous, such as the Togara North and Togara South projects in Central Queensland.

Jan 1, 1998

By E. R. Slatick

The northern and central Appalachian coal basin in the eastern United States has been the source of about two-thirds of the nation's coal output during the 20th century. This region includes parts of Pennsylvania, Ohio, Maryland, West Virginia, Virginia and eastern Kentucky. It covers about 130,000 km2 (50,000 sq miles) of the Appalachian coal basin and ranks as one of the world's most important coal production regions (Fig. 1). The coal industry's heyday in northern and central Appalachia has passed. This was due to competition from other fuels and low-sulfur coal produced in the West and because of the declining use of coking coal for steelmaking. Nevertheless, the region still plays a vital role in US coal production. It currently produces about 40% by weight of the nation's coal (its share is about one-half when measured by the energy content of the coal), contributes substantially to electricity generation and serves as the mainstay of US coal exports.

Jan 1, 1995