Search Documents

By P Hollings, J Holliday

Porphyry copper, gold and molybdenum deposits form in subduction-related settings in association with calc-alkalic or alkalic magmatism. Hydrothermal alteration assemblages are zoned, with potassic cores and propylitic haloes overlain by extensive domains of clay alteration and silicification (lithocaps). Copper sulfides, gold and molybdenite typically occur in veins or hydrothermal breccias, and less significantly as wall rock replacements. Epithermal deposits may form above or to the side of porphyry systems, and may be juxtaposed into the core of a porphyry deposit if rapid uplift and exhumation occur through the life of the magmatic-hydrothermal system. Volcanichydrothermal breccia pipes (ædiatremesÆ) commonly form late in the life of a porphyry system. They may contain clasts of porphyry-style mineralisation, and can host significant epithermal gold resources. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

A number of terrane reconstructions conflict with global plate histories or with data from adjacent regional studies. Paleogeographic maps have ignored terranes thus are over-simplified. This paper represents an attempt to "marry" Mesozoic global plate reconstructions and terrane analysis to produce examples of a "third generation" of global plate tectonic maps. The best approach to global terrane analysis involves intercomparison of all regional data and the evolving global model. Data conflicts within and between terranes and regions must be resolved by a system of relative data reliability "weighting." The most reliable and useful data are those which constrain "departure" (rift) and "arrival" (collision) times. Certain ad hoc decisions aid in the analysis (e.g. only one net vector allowed per plate). The maps that follow summarize Early Mesozoic global tectonic history at three critical junctures: 240 MA (Triassic); 180 MA (Jurassic); and 120 MA (Cretaceous). Due to space limitations, maps drawn at 20 m.y. intervals appear elsewhere. A preliminary Middle Triassic reconstruction is presented in Figure 1. Major plates and continental blocks are labeled; smaller blocks are marked with abbreviations. Examination of Figure 1 indicates the necessity of modeling Triassic tectonics with at least 68 blocks. Spalling- off of microcontinental slivers from Gondwanaland is active some 70 m.y. before the actual breakup of the supercontinent. In the SW sector of the Pacific, the Australian margins were embroidered with several terranes (e.g. Sumba) which eventually rifted away and crossed Tethys. The NW sector at this time included 10 microcontinental chips forming a huge archipelago along the Asian margin. All blocks inboard of Indochina collided by latest Triassic. Terranes of the NE sector include several (e.g. Arctic Alaska) along the North American margin, and at least six large blocks (e.g. Stikinia) drifting SE with the Farallon Plate. The SE sector

Jan 1, 1987

The need to describe shape properties of solid particles arises in many applications in the mining and minerals industry. This paper presents a technique for describing the shape of 2D particle profiles from digital images, based on traversals of the circumference of the profile boundary at a succession of different scales. The traversals are undertaken in such a way as to establish a more stable set of results than usually arises from conventional fractal multi-scale shape characterisation techniques. The resulting values can be used to provide compact information on various generic shape features of the particle profile.

Jan 1, 1998

By M. R. Nelson

Continuing experience in the Black Hills, South Dakota, indicates the persistence of several natural contaminants in mine waste effluents under circumneutral pH conditions. Selenium and arsenic are the most problematic environmental contaminants observed in these effluents. The contaminants are present in ore and waste rock as naturally occurring trace elements, and under the physico chemical conditions of the mine waste repositories are mobilized by oxidation and desorption reactions into infiltrating water. Characteristics of the mine wastes, waste repository construction, and Black Hills climatic conditions, indicate these natural contaminants may persist well into the future causing long-term mine closure liabilities, a difficult challenge to both mine operators and regulators.

Jan 1, 2003

By K. Ford, R. Urquhart, D. Hobbs

CIS countries are home to some of the world's largest producers of chrome, manganese and silicon ferro alloys and leading suppliers to world export markets. The region's ferro alloys production is rising faster than demand from its domestic steel industry - unit alloy consumption in domestic steelmaking is in fact falling as process efficiencies improve - and there is significant spare capacity available to increase production. CIS producers enjoy certain strategic advantages in the production of ferro alloys - for example, captive ore sup-plies, low power and labour costs - but must also meet certain challenges - such as lower labour productivity and greater distance to market than some of their competitors. CIS producers are ambitious but new investment is needed to upgrade some aging plants and overhaul outdated process technologies if they are to be more competitive with the world's leading producers and address the environmental issues that are now moving up the agenda. This paper describes the structure of the region's ferro alloys industry and discusses its advantages and disadvantages by alloy and by country. It considers how the ongoing process of restructuring and new investment in the industry might move forwards, based on its strengths and weaknesses, technical and environmental factors and the strategies of the main players. It asks how the industry might maximise its substantial potential - in particular, for the production of chrome and manganese ferro alloys - and examines the implications this holds for all global ferro alloys players.

Jan 1, 2007

By P. G. Semple

For the last four years, the Kilborn Group of Companies has been involved in several major projects in the Confederation of Independent States (CIS). These include the Kumtor project, the Kubaka gold project, the Kazgold project, the Aginskoe project and the Jerooy project. These projects are all in various stages of detailed engineering and construction. Western mining companies are pursuing mining opportunities throughout the world in search of ore bodies for development. The quest for profitable mining ventures has led mining companies to South America and Asia and, more recently, to the former Soviet Union. When considering the CIS, several factors should be considered. The most notable are geography, mining culture and previous mining production.

Jan 1, 1996

By P. G. Semple

For the last four years, the Kilborn Group of Companies (Kilborn) has been involved in several major projects in the CIS. These projects include the Kumtor Project, the Kubaka Gold Project, the Kazgold Project, the Aginskoe Project and the Jerooy Project. These projects are all in various stages of detailed engineering and construction. In this paper, Kilborn will discuss our experience in the CIS and share some insight into project development in this geographic region.

Jan 1, 1996

By Huang Qiming

The CISDI-GreenEAF innovatively applies the top-side-chute for charging for improving the cold zone of electric-arc furnace (EAF) requiring preheating scrap. It can greatly reduce the operating power consumption during EAF melting by combined use of fume for preheating scrap. The enclosed charging mode and specially-designed structure contribute to less emission of dust and fume during charging while enhancing the metal yield. Thanks to the extraordinary fume temperature control at scrap preheating procedure and fume quenching technology as developed by CISDI, for restraining the regeneration of dioxin.

Oct 30, 2017

By Y. Luo

A PC based computer model has been developed by the authors for predicting the surface subsidence due to underground coal mining. Its reliability, comprehensiveness and user friendliness demonstrate that it is a good tool for the mine operators, government agencies and scientific researchers alike.

Jan 1, 1989

By Yi Luo

Multiple-seam mining operations induce surface subsidence basins different from those caused by mining in a single coal seam, and also disturb the mining operations in the other coal seams. A computer program, CISPM-MS (Comprehensive and Integrated Subsidence Prediction Model for Multiple Seam Mining), has been developed to predict the final surface movements and deformations as well as the interactions associated with multi-seam coal mining operations. The program applies a newly developed subsurface subsidence prediction model that is able to consider the geological stratification variations. In predicting surface subsidence, the surface movements and deformations caused by the individual mining operations as well as the interactive effects are all considered. A case study is conducted in this paper for validating the program.

Jan 1, 2012

By L Y. Yang, Z Wang

This work presents the fundamental properties of CITIC magnetite concentrate and its performance in pelletising and sintering. CITIC concentrate has been widely used in pelletising to produce pellets for blast furnaces. It is also used in sintering to benefit from its sintering performance. CITIC concentrate has excellent balling properties owing to its size distribution, particle surface properties, large specific surface area and balling index, leading to strong green pellets and product pellets. When used in sintering at appropriate levels, sinter bed permeability improves, productivity is increased while coke consumption reduces, and sinter strength improves.

Nov 8, 2021

By M Warnken

Major cities are not only the focal point for AustralianÆs work, leisure and homes, they also are the focal point for the flow of resources into the built environment, motor cars and transportation and urban consumables. The steady increases in æstockÆ and waste generation, in line with GDP growth, means that cities will become the mine sites of the future if the inherent value is recovered from these materials at end of life. The urban waste stream can be characterised as containing approximately nine per cent hydrocarbon-based materials; 57 per cent biomass-based material; 28 per cent fully mineralised materials that are inert, five per cent metals and less than one per cent of problematic materials that are potentially hazardous and toxic. In order to convert these wastes into value added inputs into the economy, a number of technological interventions are required. These æurban waste mining techniquesÆ revolve around source separation and material streaming. One issue that needs to be overcome when determining which mining technique to implement, is identifying the option that will deliver optimal value, both from a financial and a sustainability perspective. The difference between embodied energy and calorific value is a case in point. Highest net resource value (HNRV) is a concept that can assist in choosing between different resource recovery options. The assessment can be done at a strategic level, or can be used to work out material specific issues. For example, used tyres can be recovered for their energy content at an approximate cost of $120 per tonne, whereas mechanical processing of used tyres can deliver a net benefit of $192.

Jan 1, 2006

The Pinto Valley, Arizona, plant of Cities Service Company is one of the newest copper producers in the United States, having started production in 1975. It is located a few miles west of Miami, Arizona, on the site of the Castle Dome Mine, a World War II operation which was shut down and its mill later moved and renamed the Copper Cities plant. The Pinto Valley concentrator uses six 18 ft (5. 5 m) diameter by 21 ft (6.4 m) long, 4000 hp, single-stage ball mills, taking crushed ore from four 7 ft (2. 13 m) standard and eight 7 ft shorthead crushers. It has a design capacity of 40,000 stpd but has higher tonnage capability for an expanded concentrator. The copper porphyry-ore is mined by two 15 yd and one 20 yd shovels (11.5 and 15.3 cu m) and is transported to the primary crusher by 150-ton trucks. The dump pocket is relatively shallow (14 ft or 4. 27 m deep); and because of the width necessary for the 150-ton trucks, it was designed to use the ore itself instead of manganese steel as an abrasion- resistant lining, although a heavy steel cap protects the dump pocket top edge. The pocket has a capacity of 300 tons of ore. Water sprays under the dumping positions direct a fog toward the truck being dumped for excellent dust control. Breaking of oversize is done by a hydraulic impact breaker mounted on a hydraulically operated articulated arm situated at the side of the dump pocket. Again because of the shallow pocket, no splitter is used to protect the spider of the 60 in. by 89 in. Traylor gyratory crusher, which is equipped with a hydroset mechanism. Crushed ore at 8 in. (203 mm) drops into the 360 st surge chamber lined with AR plate and then is fed directly to the 60 in. (1.52 m) stock- pile conveyor by an 84 in. by 20 ft (2. 13 m by 6.1 m) four-speed apron feeder at a rate of up to 4000 stph. Early in 1977, Cities Service will replace the four -speed electric drive with a hydraulic pump and motor with infinitely variable speed. They are also studying the replacement of the apron feeder with an 8 ft wide (2.44 m) belt feeder similar to those at Similkameen and Palabora. Peak crushing capacity would then be increased to 5000 stph. The AR plate in the crushed ore pocket was installed in large, rectangular sheets which required much less embedded metal to hold it in place than would the more conventional, smaller arid square pieces of cast manganese steel. For duty in the crushed ore pocket, where wear is not severe, the AR plate is a satisfactory material. The new Palabora Figure-8 crusher also uses this design.

Jan 1, 1978

By R. A. Reiley

Introduction Democratic countries are founded on the principle that all citizens have the right to participate in policy setting and decision-making processes. Citizen participation is especially evident in environmental issues and policies. In the United States, there are currently over 10,000 environmental organizations and new ones are being formed each year. Many of these organizations are formed on a watershed basis and are particularly concerned about the impact mining has on the environment. While the environmental issues vary from area to area, most concerns center around mining impacts related to subsidence, water pollution, and water diversion. Citizens have a number of avenues for participating in lawmaking that affects the mining industry. Some of these avenues include participation in litigation and citizen ballot initiatives. In addition, there are less formal methods of participation that include attending public meetings, commenting on agency rules or lobbying on specific legislation. The intent of this article is outline the various public participations mechanisms, highlight the latest legal developments that have affected mining industry through citizen participation, and briefly discuss emerging issues.

Jan 1, 2001

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

This study investigated the performance of citric acid as lixiviant for cathode material from end-of-life lithium-ion batteries (LIBs). Black mass containing 84.2 weight percent MNC (LiNi0.45Mn0.4Co0.15O2) and 15.8 weight percent LCO (LiCoO2) material was leached at solid-to-liquid ratios of 20, 50 and 100 g/L. Leaching with 1.5 M citric acid, 2 volume percent H2O2 and a solid-to-liquid ratio of 20 g/L at 95 °C extracted 90 percent Co, 95 percent Li, 94 percent Mn and 94 percent Ni within 20 min. At the highest solid-to-liquid ratio of 100 g/L with 1.5 M citric acid, 10 volume percent H2O2 and 95 °C, 84 percent Al, 84 percent Co, 87 percent Li, 86 percent Mn and 96 percent Ni were leached after 40 min, producing a leach solution containing 0.68 g/L Al, 20.0 g/L Co, 6.0 g/L Li, 13.6 g/L Mn and 19.3 g/L Ni. Using stepwise addition of H2O2, instead of initial bulk addition, did not significantly improve the leaching efficiency but did reduce the required leaching time. Temperature control of the reactor was also more manageable with stepwise addition of H2O2, and evolution of gas was less vigorous. It was observed that the leaching efficiencies of Co, Li and Mn decreased slightly at solid-to-liquid ratios of 50 and 100 g/L, while the leaching of Ni increased slightly. The solution leached at 20 g/L could be stored for six weeks without any spontaneous precipitation. However, solutions leached at 50 and 100 g/L showed changes in concentration after one month of storage, suggesting that processes that have a large material throughput and use high solid-to-liquid ratios around 100 g/L must ensure that the solutions are not stored for extended periods of time.

Apr 1, 2025

By Baron Miya, Keith Hanks, William Edgerton, Francis Fong

The City of Los Angeles capital improvement program includes the construction of a new 35-km interceptor sewer. This sewer will be built as a deep tunnel with finished diameters ranging from 2- to- 4 meters. The project will be constructed concurrently in two phases; an 18-km East-West and a 17-km North-South segment. The new sewer provides additional conveyance capacity for an existing deteriorating sewer that is scheduled for rehabilitation. Large sewage spills during the El Niño storms of 1998 resulted in a Cease and Desist Order that established an aggressive schedule for the completion of the project.

Jan 1, 1999

By S. R. DeBoer

A study of Western cities reveals the fact that a city where people make their homes for permanent residence is always a city with, well-shaded avenues, with parks and playgrounds; in other words, a beautiful city. On the other hand, the average city that lacks these qualifications is usually a city of transient population. Many of our Western cities must be classified as such. Their inhabitants live in such a city only to the time that they will be able financially to retire from business and go to one of the other types of cities to live; or until opportunity offers itself for a position or a job in such a city. I believe that our Western coal camps could benefit by this truth. If conditions can be created in the camps that will encourage the workers to settle permanently or for a long time at least in the town, it would greatly aid in stabilizing employment. By the term "workers" I do not mean the pick and shovel men alone, but everybody from the superintendent or the manager down; for the educated part of the population suffers probably greater from a desire for better surroundings than the less educated part. Modern City Planning tries to show the way for more attractive towns; for more practical towns also, and at less expense. The grid-iron system of street planning is slowly being replaced by one that fits the contours of the site. Instead of streets that are cut through the hills and built over the valleys to get practical grades, it tries to show how these streets can be made to fit the ground and produce better traffic lines; greatly more attractive streets; better building sites and lots, and all of this at less expense. A well-planned town of this character should have as its nucleus, a central square around which the main stores and business houses are grouped. The main building of this group should be the church, the community meeting place, city hall or such other buildings of a public or semi-public character, that are imposing enough to add interest to the square. From this central square, streets should be built to radiate out in all directions, more or less like a spider-web. The main lines of these streets should be reserved for traffic purposes and they should be wide, for the town may grow into a city, and they should be direct, connecting the town center with outlying points at the shortest and easiest possible line. Between these radiating streets should be residential streets of narrower width and arranged in such a way that fast through traffic cannot pass over them and make them unsafe and unsanitary for family life. Following up the comparison with the spider-web, the town should have circular streets, encircling the whole town with rings at various distances out, along which circular lines parks should be located. In the West, where the need for shade is so great, the town should surround itself with a belt of forest trees. Such a forest belt would break the winds and shelter the town, and also make the whole town a cozier, nicer place to build a home in. A forest belt of this kind does not necessarily mean a great layout of money. Trees can be planted small and at little cost and a carefully studied irrigation system will make the maintenance cost small. If the town has any places of natural beauty they should be carefully preserved and made accessible. Natural parks of this type will often take the place of the artificial parks of large cities, and at no expense to the community. Playgrounds, a swimming pool, either of concrete or a sanded beach on a lake; a place for all to go skating in winter; a hill for sledding in

Jan 1, 1924

By Charles E. Hughes

HERBERT HOOVER had to sit through an hour and a half of eulogy of himself at Carnegie Hall last night, said the Sun and New York Herald of Feb. 19. When his turn to answer came he remarked that, although one of the speakers had referred to him as a modest man, he would never, in view of this experience, be able to prove it. The occasion was the presentation by the Civic Forum to Mr. Hoover of its medal of honor for distinguished service, the only recipients in past years having been General Goethals, Thomas A. Edison, and Alexander Graham Bell. Only by distortion of intent could there be said to be anything political in the affair, which was carefully described by the chairman, Charles E. Hughes, as non-partisan. Nevertheless, the praise bestowed on the former Food Administrator by the former Republican candidate for President, proved specially interesting to a much applauding audience which filled the hall to the uppermost gallery. A piece of real news was supplied by Horace V. Winchell, whom Mr. Hoover succeeded on Tuesday as President of the American Institute of Mining and Metallurgical Engineers. He said that Mr. Hoover, when in Europe after the . armistice, caused to be collected the literature of the war in all Europe.

Jan 1, 1920

By Klaus W. John

The geologic factor of greatest significance in rock mechanics and rock engineering is considered to be the geologic structure represented by joints, faults, and other planes of weakness. This geologic structure differentiates between the rock element and the rock system composed of these elements. Only during the last decade has the difference of the technological properties of element and system been recognized but this appears to be more in theory than in engineering practice. If rock mechanics is to achieve real significance in engineering practice, it has to provide methods of analysis which are realistic compromises between the best representation of the actual conditions and pragmatic engineering. The rock mechanics practitioner has to face the fact that many geological engineering and rock mechanics problems may be too complex to allow rigorous analysis but at the same time are deemed satisfactory for the construction of major structures. Ultimately, the geotechnical engineer or the engineering geologist has to express the effect of geologic factors in quantitative, even if approximate, terms and provide numerical data on strength and deformability of rock systems to be utilized in construction. Qualitative evaluations, quantitative descriptions of geologic features as such, and comparisons of specific test results are always of interest but may not suffice as basis for engineering decisions and designs. The present efforts of the rock mechanics group at the Karlsruhe University, Federal Republic of Germany, are based on a systematic combination of geomechanical models and numerical analyses based on the finite element approach. This group considers that at the present stage

Jan 1, 1970

By John Goodell

CIVIL engineers seem to number in their ranks more advocates of licensing than are found among the practitioners of other branches of the pro-fession. Licensing was not originated by civil engineers but it was forced upon them in two ways. In the first place, the civil engineering profession has hangers-on like every other profession. The first legislative result of their imperfect accomplishments with which I am familiar occurred in the far West. It was found that early irrigation works were so badly planned in some cases that not only were water rights made very uncertain but considerable sums were invested in structures and ditches which proved inadequate and occasionally complete failures. Water was too valuable to be wasted in that way and money too hard to obtain. In those sections, therefore, laws were passed many years ago which made it obligatory for the design of irrigation works and other structures utilizing water to be made by engineers who had satisfied a board of examiners that they possessed the technical qualifications to plan such works properly. The basic thought on which such laws rest is the same as that on which laws governing the licensing of boiler operators rest, namely, the safety and welfare of the public. While boiler explosions still occur and irrigation works are built which are not wholly satis-factory, these laws have helped the, public, it is gener-ally agreed.

Jan 4, 1922