Search Documents

By D. Vavadakis

Abandoned bauxite surface mines in the Parnassos area may be rehabilitated using bauxite residues as filler. The objective of this study was to estimate the percentage of precipitation that may infiltrate through the bauxite residues to the lower geological formations when they are disposed off in mine open pits. Two scenarios were investigated simulating: a) available field tests, and b) a demonstration test that was planned to be performed in an abandoned open pit close to the Aluminium of Greece plant. It was indicated that the annual infiltration from bauxite residues disposed off in the demonstration test for the most probable scenario is very low, equal to 13.17mm corresponding to 3.1% of the annual precipitation. Furthermore, it was estimated that the annual percolation from the field tests is approximately 4.4%, very close to the infiltration values measured in the field tests for the same period.

Jan 1, 2006

By K. Kavouridis

On 30 April 2004, a large scale slope failure incident occurred at the external waste dump facility of the South Field Mine, in the Western Macedonia Lignite Center, Greece. This landslide involved the mobilization of waste overburden material (that was continuously deposited for the last 20 years) in the order of 40 Mm3, while the material that moved outside the boundaries of the waste dump was in the order of 3 Mm3. The factors that led to failure as well as the procedures and measures taken in order to stabilize the failure and resume normal operations at the South Field Mine are presented and discussed. Emphasis is given to the impact on mine operations and the cost related to resuming of normal production operation as well as to implementing important modifications and improvements of the materials handling system.

Jan 1, 2006

By W. J. Schlitt

The development of forced aeration as an approach to enhancing copper sulfide leaching is traced from its earliest development up to present day operations using this technology. Both large-scale field tests and commercial operations are covered. The historical portion is preceded by an introductory discussion of the role of air (oxygen) in sulfide leaching. Sufficient aeration may be achieved via naturally induced convective airflow. However, cases are identified where this is insufficient, leading to retardation of the sulfide leach rate. For these situations, forced aeration may be beneficial. The historical portion of the paper focuses on the major field tests that have been conducted in Montana, Nevada and Utah, along with commercial operations in the United States, Australia, Chile and Peru. The paper concludes with some general comments about the applicability of forced aeration, which are based on the information developed to-date.

Jan 1, 2006

By R. Jovanovic

The main technological indicators of copper flotation which determine the level of revenue per mass unit of processed copper are utilization and the content of copper in concentration. This study describes the economic-technological model of copper flotation which can help determine, for the given technological and market conditions, an optimal percentage of copper in concentration, whereby the maximum revenue is achieved per ton of the processed ore in the process of flotation.

Jan 1, 2006

By Andrew Howard

As the mining industry moves further into developing countries in search of new resources, its role in international development is coming under increasing scrutiny. This is a trend that is likely to accelerate, along with the potential for headaches among managers in the industry. Public interest in development and environmental issues is rising as faith in “big business” falls. This has strengthened nongovernmental organizations (NGOs) campaigning for sustainable development. And it has put more pressure on banks, governments and development agencies to curb corporate misdemeanors. Developing world governments are also becoming emboldened to reject previously agreed terms they do not consider equitable. The mining industry has begun to formulate a response to these pressures but must go much further. Societal and environmental issues must move from public relations to core strategic thinking. Abiding by rules or codes is not a relevant response. Instead, genuine support for sustainable development is required. This will involve delegating the responsibility for engaging with local communities to on-the-ground staff and developing a dialogue with local stakeholders rather than conducting an initial assessment and disengaging.

Jan 1, 2006

By T. Burchett, F. Stanley, K. McGough, G. Luttrell

The vast majority of U.S. coal preparation plants utilize screen-bowl centrifuges to dewater their fine clean coal products. In light of this popularity, researchers at Virginia Tech have engaged in a variety of laboratory and industrial field test programs to develop technological enhancements that have the potential to further improve the performance of this important solid-liquid separation process. These enhancements, which include simple design modifications and new reagent packages, have been shown to significantly improve solids recovery and reduce product moisture in several experimental trials.

Jan 1, 2006

A series of laboratory based push and pull tests were carried out to investigate how surface profile influence the load transfer mechanism of bolt/resin interface. Tests were carried out in both 75 mm and 150 mm long steel sleeves. Three types of bolts were examined, they were bolts most commonly used for strata reinforcements in underground coal mines in Australia. The bolts had near equal core diameter but of different profile configurations. The change in the length of the encapsulation sleeve was examined in light of the small number of profiles encapsulated effectively in short 75 mm long sleeves. The results showed that peak loads and displacements were directly related to the height and the spacing of the bolt surface profiles. Profile spacing appears to have greater influence on load transfer capacity than the profile height.

Jan 1, 2006

The Mining Foundation of the Southwest will host its 24th Annual American Mining Hall of Fame Awards Banquet at the Tucson El Conquistador Golf & Tennis Resort in Tucson, AZ on Saturday, Dec. 9. The Mining Foundation of the Southwest is a non-profit organization whose objectives are public education about the mineral industries. It also recognizes outstanding accomplishments in and contributions to the fields of fuel and mineral resources.

Jan 1, 2006

Asgco’s design of the Arrowhead Ceramic Lagging provides solutions to problems experienced with conveyor belt slippage around the drive pulley and severe wear problems on snub and bend pulleys. Asgco has developed a range of pulley lagging from ceramic, drive rubber and non-drive rubber lagging that is available in abrasion-resistant SBR and MSHA grade rubber for conveyor pulleys from slow belts all the way through to high-speed, high load belts. There is a growing need for a maintenance-free and reliable pulley lagging to ensure conveyor belts run to their highest efficiency.

Jan 1, 2006

By I. Michalakis

A geological and geophysical study was con-ducted at the area of Stylos, Hania in order to study the possible mechanisms of saltwater contamination. A new detailed geologic map in scale 1:5,000 was combined with the results of a time lapse geophysical survey using seismic and electrical methods. A fault system in the N-NE direction possibly favors the saltwater intrusion.

Jan 1, 2006

By A. Peppas

Perlite is a naturally occurring siliceous rock, which can be expanded from four to twenty times its original volume when heated at a temperature close to its softening point. The expanded perlite is characterized by increased sound and thermal insulating properties. However, the conventionally expanded perlite products have high porosity and low mechanical properties that limit the range of their applications in the construction and chemical industry. The present work aims at the development of new closed porous microcellular material from perlite with enhanced mechanical and physical properties to be applied in new applications, like joint compounds, functional fillers for special paint types, special blasters and mortars, artificial marble. For the production of these new materials a vertical electrically heated furnace with six different heating zones and controlled gradient temperature profile was used. The effect of major process parameters, like temperature and air flow, on the quality of the produced materials was studied using Greek perlite from Milos Island. The quality of the new products was evaluated in terms of their bulk density, compression strength, water and oil absorption, surface area and pore volume. The experimental results show that the produced materials are characterised by improved mechanical and physical properties compared to the conventionally expanded perlite products.

Jan 1, 2006

By D. Moraetis

The present study examines the nutrients and micronutrients availability of uncultivated soils originated from different parent rocks. The study areas include four types of parent rocks with different geological origin, from acidic to ultramafic. The parent rock mineralogy and the nutrients available in soils are in strong relation-ship. Mineralogy, particle size distribution and chemical composition of the soil samples were studied jointly with the nutrient content of soil solution. High magnesium availability in soils of Anogia area is related with the alteration products of the ultramafic rocks. Potassium content of the soils exhibits no relation with the geology of the area. Micronutrients, iron and manganese, shows strong dependence to the bulk chemistry and mineralogy of the parent rock material. In contrast no interrelation detected between zinc and copper availability in soil and parent material.

Jan 1, 2006

By Z. Kowalski

Landfilling of waste causes the degradation of natural environment, not only due to land occupation, but also due to pollution of air, water and soil. The flotation waste from zinc-lead industry also poses such problem. There is a need to find the way to utilise substantial amount of these wastes and backfilling seems to be a good solution. Recently, in Poland only sand was used for backfilling. However, it will be more beneficial to substitute the sand with the industrial solid waste, especially flotation waste. The tests were performed in the laboratory to examine the use of flotation waste as a main ingredient for backfilling. The use of flotation waste is possible only when it is combined with other waste with specific bonding properties, especially regarding the prevention of leakage. The outcome of tests shows that flotation waste combined with cement and fly ashes can be used as a backfilling material. This paper presents the preparation of flotation waste for using it for backfilling.

Jan 1, 2006

By D. Triantis

This paper presents the results of laboratory experiments for the detection of electric signals from Fiber Reinforced Polymer (FRP) sheet samples which have undergone a temporally increasing loading of bending type up to fracture. Electric signals that were recorded while the sample was subjected to bending are referred from now on as Bending Stimulated Currents (BSC), in order to differentiate them from the relevant signals emitted by materials that suffer uniaxial compressional stress. The latter signals are referenced as Pressure Stimulated Currents (PSC). BSC emitted from FRP sheet samples presented here, were recorded after applying three successive load steps to samples. The increase rate of applied stress was about 0.15kN/s. Initially starting from low load values to higher load values until the FRP sheet reaches at a state just before its failure. The BSC records from FRP samples are compared to equivalent recordings from cement mortar beam and distinguishable differences are discussed.

Jan 1, 2006

By A. Zutshi

Production of CO2 is an inevitable consequence of burning fossil fuels, with the only CO2 sequestration technique feasible in the immediate future being its injection in various geologic media. This paper discusses the factors that influence the injection, movement, and storage of CO2 into deep coal seams, while simultaneously increasing the production of methane. The results of a laboratory-scale study to evaluate the movement of CO2 in coal, its ability to displace methane, and the capacity of coal to retain CO2 are presented. The findings are compared with observations at one of the two field-scale pilot operations practicing CO2 injection in coal. Finally, the paper summarizes the research issues that require further investigation.

Jan 1, 2006

By N. Economou

Temporary local seismic networks were installed in western Crete, in central Crete, and on Gavdos, an island south of western Crete, in order to image shallow seismically active zones of the Hellenic subduction zone. Data acquisition was divided in four campaigns through the years 1996 to 2001. More than 4000 events in the magnitude range between 0.5 and 4.8 were detected and localized. The resulting hypocenter distribution allows the localization of seismically active zones in the area of central Crete from the Mediterranean Ridge to the Cretan Sea. The comparison of the hypocenter distribution and the structure has allowed intraplate and interplate seismicity to be distinguished. A southwards dipping zone of high seismicity within the Aegean lithosphere is found south of central Crete in the region of the Ptolemy trench. Between 20 and 40 km depth beneath central Crete, the Aegean lithosphere appears to be seismically inactive. Especially for the year 2001, 1560 events were localized, by the seismic network installed on Messara, central Crete. Most of the seismic events were located, as expected, in the South region of central Crete. National Observatory of Athens (NOA) maintains a permanent seismic network in Greece. In this work a comparison of the earthquake epicenters obtained from both the NOA network and the BOCHUM-TUC network is presented.

Jan 1, 2006

By D. Tao, R. Honakey, B. K. Parekh

The dewatering of stable phosphatic clay suspensions generated from phosphate beneficiation in the central Florida is an issue of practical and theoretical importance. Because of its tiny particle size and surface charge, the phosphatic clay takes up to 20-30 years to settle in water and causes environmental, aesthetic, economic, and handling problems. An efficient and cost-effective dewatering/consolidation process for phosphatic clay is of great interest to the phosphate industry in Florida. In this paper, the consolidation and dewatering behavior of phosphatic clay was studied by use of anionic flocculants with and without sand addition. The effects of pH, initial polymer concentration, polymer dosage, polymer addition steps, and metal cations (K+, Ca2+, and Al3+) on the flocculation of phosphatic clay have been studied. Experimental results indicated that clay suspensions were well flocculated at pH 10.5 by DPW-1-1355 and Magnafloc 5250 flocculants acquired from Ciba Specialty Chemicals. Sand particles from phosphate flotation added to the clay slurry promoted flocculation and increased clay consolidation. K+ showed good performance to improve the flocculation characteristics by neutralizing clay surface charge. The adsorption mechanisms of flocculants on clay particles were also discussed in this paper.

Jan 1, 2006

By R. L. Grayson, F. Giana, R. Aspinwall

Small-mine and contractor Fatal Incidence Rates have been a problem for over 20 years in the coal industry, and the rates persist as unacceptably high. This paper briefly retraces historical information and data on the continuing problem and recounts the many unsuccessful efforts and initiatives to address the problems effectively. Next the results of a review of international literature on addressing the problems are presented. After focusing on a method to pinpoint the trouble spots more specifically through a nested data analysis, suggestions are provided on how the problem may potentially be addressed more systematically and effectively in the U.S.

Jan 1, 2006

By G. Krogman, C. Walla, B. Wood

The Gebo Mining District (District) is located in the Bighorn Basin of Wyoming. Commercial underground coal mining began in 1906 with the arrival of the railroad in Thermopolis, which is located approximately 11 miles to the south. Mining in the District ceased by the early 1970’s. In Fall of 1999, Lidstone and Associates, Inc. (LA) and their subcontractors were retained by the Wyoming Abandoned Mine Land Division (WyAML) to perform an inventory of over 500 abandoned mine sites across Wyoming. During the summer of 2000 field inventory, a 30-foot deep headcut (Figure 1) and sink-hole were noted in the West Fork of Sand Draw (WFSD), immediately west of the Town of Gebo. The headcut and sink-hole were located at the culvert outfall associated with a stream crossing of a relatively well traveled county road. Upon further investigation, it appeared that underground mine workings had been exposed at this location. This resulted in a condition whereby water would be conveyed directly into the mine workings during a runoff event. The exposed mine workings as well as stream capture created a very hazardous condition. The WyAML implemented mitigation measures in the summer of 2000 by constructing a temporary stream crossing upstream of the existing failed crossing. To address this hazardous situation as well as a number of other hazards identified in the District during the field inventory, the WyAML retained PHC Reclamation, Inc. (PHC). PHC was directed to perform a field investigation and develop a Reclamation Plan to address all existing abandoned mine hazards in the District. Federal, state, and private parties own lands within the District. Hazards identified during the investigation included an underground mine fire, open adits, open shafts, subsidence, drainage problems, and coal slack. A Report of Investigation (ROI) was submitted to various regulatory agencies that documented the existing conditions and conceptual reclamation plans to remediate the hazardous conditions. After review of the ROI by the US Department of Interior - Bureau of Land Management (BLM) an on-site meeting was conducted. BLM Cultural Resource personnel declined to approve a District reclamation project until a historical overview of the entire District was prepared. Due to the hazardous situation associated with the WFSD stream crossing, Hot Springs County Road and Bridge Department convinced various state and federal regulatory agencies to allow reclamation of the stream crossing to occur. A decision was made to allow reclamation on privately owned lands within the WFSD drainage. This decision limited the amount of channel that could be subjected to reclamation upstream of the crossing to privately owned lands. PHC contracted LA to perform a geologic, geomorphic, hydrologic, and hydraulic investigation of the drainage to assist in the development of a WFSD reclamation plan. LA’s investigation consisted of four parts: Delineate the extent of mine workings in the area; Identify all drainage structures that required mitigation; Survey a series of channel cross-sections and a longitudinal profile of the impacted channel; and, Develop basin hydrology to assist in the design of a stable reclaimed stream channel.

Jan 1, 2006

By P. C. Thakur

Frictional ignitions (also called face ignitions) is defined as the rapid oxidation of a mixture of methane and air with a visible flame that could last from a few seconds to several minutes. These ignitions have a potential to turn into a mine explosion and eventually a large-scale mine fire. Over the last 22 years, U.S. coalmines have had 1566 frictional ignitions. There were no fatalities but serious injuries have occurred. Every effort, therefore, should be made to prevent frictional ignitions. The preventative measures fall under four categories: (a) degasification of coal seams prior to mining, (b) adequate ventilation, (c) wet cutting or water-jet assisted cutting and (d) machine design to minimize ignitions. The paper discusses each of these techniques in detail.

Jan 1, 2006