Search Documents

By L. H. Michaud

An existing mining company plans to extend their surface coal mining operations in central Pennsylvania. Although the proposed site contains pyritic material, the results of the acid-base accounting for the site show an overall NP:MPA ratio of 4.26:1 for the entire site. The pyritic material is, however, associated with the lower of the three seams to? be mined. If traditional dragline mining methods were used, this would result in the acidic material being placed at the top of the spoil piles, exposing it to air and water, and therefore to the formation of Acid Mine Drainage (AMD). Further concerns are associated with the fact that the alkaline material is not distributed evenly over the mine site. In order to prevent the formation of AMD, the company has proposed to mine the area using Truck/Shovel mining methods. This technique offers a more flexible alternative for cut sequencing and for the selective placement of waste material. Working with the Department of Mineral Engineering at The Pennsylvania State University, a mine plan was developed for this site. This plan results in the layering of the alkaline and acidic spoil in order to achieve an overall net alkalinity in all spoil areas. Mining of this site should therefore not result in the formation of AMD.

Jan 1, 1994

By Malcolm J. McPherson

Observations of environmental parameters in mines have traditionally been made by means of hand-held instruments, these being employed as a basis to ensure that atmospheric conditions in the mine remain within limits commensurate with safety, to safeguard the health of personnel, and to ensure that statutory requirements are met. Thus, starting from the first flame safety lamps of the early nineteenth century, numerous portable instruments have been devised over the years to indicate levels of dust, temperature, humidity, and concentrations of gases including oxygen, methane, and carbon monoxide. Similarly, portable instruments have been used to measure air velocity and pressure. For routine monitoring purposes, hand-held equipment suffers from many disadvantages. Readings are intermittent, often with long delays between successive observations, making short-term trend analysis impossible. Portable instruments are more liable to damage; they are labor intensive and provide a very limited amount of information either for control or planning purposes. The 1960's and 1970's have seen an accelerated development of mine environmental monitoring equipment. Alarm methanometers to give localized audiovisual signals became more common. These were followed by a variety of instruments which gave local, then local/remote continuous records, particularly of methane concentration and airflow. More sophisticated transducers and transmission systems were developed allowing further parameters to be monitored. This led to a proliferation of paper strip and chart recorders which had to be maintained and inspected regularly for trends and abnormalities.

Jan 1, 1979

By D. K. Sitler

Continuing advancements in manufactured diamond materials as used in rock cutting tools have created a new generation of high production tools for mining. This paper reviews the three major manufactured diamond product types available in the mining industry as supplied by General Electric Co., Specialty Materials Dept., and examines the ways these materials are used. As an integral part of this examination, the economic impact of manufactured diamond tools is evaluuted. Time and again, one will find that the premium price for these tools is economically justified when compared to traditional tools.

Jan 1, 1988

By Ramon S. Pizarro, W. Joseph Schlitt

Introduction Trying to synthesize innovations occurring in gold processing is not simple. At present, this technology is exploding, brought about by the high price of gold. This price has compelled the mining industry, as a matter of survival, to produce gold. The frantic search for gold deposits continues, from glacial areas to tropical jungles. The search has been fruitful. New exploration techniques have helped to locate deposits. Some are amenable to conventional processing techniques. Others are in unusual settings that challenge the ingenuity of extractive metallurgists. Ore deposits containing traces of invisible gold, refractory mineralization, and impurities and deleterious materials that previously defied treatment are now being profitably processed. Metallurgists have developed various processing methods and equipment for gold ore treatment that reflect differences in ore characteristics, grade, mineralogy, reserves, topography, climate, and location. These processes can be categorized as: • For nonrefractory or readily leachable gold ores - vat leaching, heap leaching, and agitation leaching. • For ores containing free gold - gravity concentration methods, followed by mercury amalgamation, and • For refractory gold ores - flotation, roasting, pressure oxidation, followed by cyanidation leaching. In actual practice, a combination of these processes may be required. This is because gold mineralization, although usually simple, may be associated with other mineral species or with clays that make the ore difficult to treat. Furthermore, after the gold has been solubilized to form a cyanide complex, one of two important processes must be applied to recover the gold. These ore zinc cementation (Merrill-Crow process) and Carbon adsorption, desorption, and electrowinning. New techniques for leaching and recovery are also advancing. These will become the bases for the next generation of gold processing plants. Nonrefractory Gold Ores Nonrefractory ores with readily leachable gold are among the .easiest to treat. Even so, non-refractory ores from epithermal deposits are likely to contain too much clay. When these ores are damp, they may clog the screens and cone crushers. Depending on the type of process, scrubbing the crushed ore is very effective in overcoming clay problems. After dewatering, the slimes enter the cyanidation process and the thickener overflow is stripped of gold values and recycled. Semiautogenous (SAG) mills are also gaining popularity due to lower capital costs and ability to treat wet, sticky ores. If properly sized, the secondary crushing and screening plants, together with a secondary ball mill, can be eliminated. When the ore is of such a low grade that it can not support fine grinding, vat or heap 'teaching may be applicable. These systems are being actively applied in the US and elsewhere. Rapid construction and low capital costs are important features of these plants. Vat leaching is ideally suited for fast leaching ores and small tonnage deposits located in areas with harsh winters or wet tropical climates. For effective vat leaching, the ore is crushed to less than 25 mm (1 in.), agglomerated with lime or cement to control fines, and leached with sodium cyanide solution (upflow or downflow). The degree of size reduction is a tradeoff between increased costs of comminution and improved gold recovery from smaller particles. However, the size of material

Jan 11, 1984

By D. M. Wyslouzil

Conditioning, in the conventional sense, means providing sufficient agitation and contact time for the reagents to react with the minerals in the ground ore. High intensity conditioning (HIC) on the other hand, as described in this paper, recognizes the need to exceed this minimum power input over a suitable length of time to induce aggregation of the finest size fraction. Time alone is not sufficient to achieve aggregation. The threshold minimum power input, kW/m3, depends on many surface properties of the fine particles and can vary considerably. In addition, the mechanical aspects and the chemical conditions must be matched to achieve good aggregation. Treatment of complex sulphide ores, requiring fine grinding for liberation, offers a large field for the application of HIC. Improved flotation rates and enhanced selectivity are some of the benefits that can be expected. This unit operation has now reached the level of commercial application. Lakefield Research considered HIC not from a fundamental point of view but as a means of solving difficult mineral processing situations arising in actual operating plants. This paper summarizes the effects of the various chemical reagent combinations that had been applied to promote faster, more selective flotation, higher mineral recoveries and cleaner separations, using HIC.

Jan 1, 1995

By Arun Patel, Diane Hirsch, Pamela Moran

The Metropolitan Washington Airports Authority (Authority) has undertaken a tremendous expansion of Washington Dulles International Airport in Fairfax, Virginia, including upgrading passenger transportation between concourses. The first stage of this expansion envisioned a shallow cut-and-cover pedestrian tunnel between the Main Terminal and Concourse B with associated vertical circulation structures. At the beginning of the design contract, the Authority’s consulting team of Earth Tech, formerly Kaiser Engineers, and the Dr. G. Sauer Corporation compared the cost and disruption of constructing the tunnel as a cut-and-cover structure to mining the tunnel using the New Austrian Tunneling Method (NATM). Upon review, the Authority endorsed the latter method.

Jan 1, 2003

By Malcolm J. McPherson

Within the world of mining health and safety, increasing attention is again being given to underground fires and explosions. This paper reviews the effects of open fires in mine entries on the ventilation system, and outlines current methodologies of attempting to control such a fire. The particular hazards of a fuel-rich fire are discussed. There appear to have been no really significant advances made in methods of extinguishing mine entry fires in the last several decades. The final section of the paper introduces research that is investigating the simultaneous production of an inerting, cooling and quenching atmosphere by means of a dense water fog.

Jan 1, 1993

By D. R. Zhu, H. S. Chiang, Y. M. Jiang, S. S. Peng

Two types of underground tests on three types of shield supports, 2-leg, 4-leg, and chock shield, were con- ducted to measure the horizontal movement of the canopy against the immediate roof. In no friction tests, steel rollers were placed between roof and canopy top, while in friction tests normal direct contact was used. Results indicate that the canopy for 2-leg shields always moves forward during setting, whereas there was no forward movement for 4-leg or chock shields. Based on the test results, a model for active horizontal force was proposed.

Jan 1, 1990

By Joseph H. Herz

Recently, the President of the Portland Cement Association, Robert D. Maclean, gave the keynote address at the Rock Products Eighth International Cement Industry Seminar. He said, after listing the seven plagues our industry is suffering, "none of these items I have listed is a sales or marketing problem. Further, none is a problem that can be relegated to long-term study by public or private research agencies. They are here-and-now problems to be faced daily by producers, researchers, equipment manufacturers and consultants. THE DAY OF THE PRODUCTION MAN IS HERE." (1)

Jan 1, 1973

By J. Wagner, P. Eger

Although lifetime estimates for sulfate reduction based on total substrate carbon typically range from 20 to 30 years, field and laboratory experiments showed that rates of sulfate reduction decreased over time as readily available organic material was consumed. When the rate of acid input exceeded the rate of sulfate reduction, alkalinity was removed from the substrate, pH decreased and metals increased. Output pH increased from 4 to over 6 after the system was shut down for several weeks and the rate of acid input was reduced. Successful long term treatment requires a design based on the input pH and the long-term organic decomposition rate.

Jan 1, 2001

By Debra C. Man, S. Thomas Freeman, F. Wiley Horne

INTRODUCTION The Metropolitan Water District of Southern California (Metropolitan) is the largest water wholesaler in southern California. Its service area spans the major urbanized portions of Ventura, Los Angeles, Orange, San Bernardino, Riverside and San Diego counties. More than 15 million people are serviced by Metropolitan through its 27 member agencies. The primary sources of Metropolitan's water supply are the Colorado River Aqueduct (CRA) and California's State Water Project (SWP). Currently, planning and design level studies are underway by Metropolitan to expand the water storage and conveyance systems within the service area for the purposes of providing increased efficiency and flexibility to manage limited water supplies, improving water quality, and increasing system reliability. The system reliability issue is particularly significant because the conveyance facilities from both the CRA and the SWP must cross the active San Andreas fault. This fault is considered to be the source fault for the anticipated "Big Earthquake" in southern California. To meet these objectives, Metropolitan's expansion plans involve a major new storage reservoir, new large diameter pipeline and tunnel conveyance facilities, more efficient utilization of existing groundwater basins, and an aggressive public awareness and conservation program. This paper focuses on the planning studies that have been carried out for over 50 miles of tunnels being considered for several of Metropolitan's proposed conveyance systems. These tunnels have ranged in length from a few hundred feet to over 42,000 feet, with depths of cover ranging from a few tens of feet to over 3,000 feet, and finished diameters ranging from 10 to 20 feet.

Jan 1, 1993

By R. H. King, R. E. Cameron

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. This paper focuses on the KRS Algorithms that extract key information from lists of time-study type event sequences. Because a static system cannot operate effectively in a dynamic mining environment, we are prototyping an index- based technique that allows the system to adapt itself to this dynamic environment.

Jan 1, 1991

By K. N. Santini

Natural zeolites are gaining recognition as an important commodity with an increasing number of industrial and consumer applications. This potential has prompted the Anaconda Minerals Company and other firms to investigate occurrences and markets for zeolites. The deposits of mordenite-rich tuff at Rome are of interest for their economic potential and for the excellent opportunity they provide to study a zeolite deposit formed in a hydrologically closed basin. Location The Rome property is located approximately 9 km west of Rome, Oregon, in Townships 31S. and 32S., Range 41E., Malheur County. It lies within the Owyhee Uplands of the northern Basin and Range physiographic province (Figure 1). The area discussed here includes a major portion of the depositional basin in which the zeolitic tuffs occur.

Jan 1, 1982

By John H. Fowler

The 30th Forum on the Geology of Industrial Minerals will be held in the historical seaside city of Halifax, Nova Scotia, from May 22 to May 27, 1994. The Forum will be co-hosted by the Provinces of New Brunswick and Nova Scotia, two of Canada's East Coast Provinces, both having a long tradition of industrial mineral production. Two previous Forums, the 19th in Toronto in 1983 and the 27th in Banff in 1991, offered delegates the opportunity to see industrial minerals in central and western Canada. The 30th Forum will take you to Canada's east coast completing the picture of Canada's industrial minerals from coast to coast.

Jan 1, 1995

By R. T. Langland

The U.S. Bureau of Mines has conducted underground tests and computer analyses to study coal mine roof behavior. Southern Ohio Coal Company provided test sites it) their Heigs mines located near Athens, Ohio. Testing apparatus was adapted for monitoring roof behavior at the face of mining from a remote surface location. Finite element analyses were applied to study the structural conditions present. Test sites were located at three different intersections of entries and crosscuts of the room-and-pillar mine. Electrical read-out instruments were used to record roof bolt loads, roof sag, and roof-floor convergence. They were installed during the roof bolting cycle of a conventional mining section and data was recorded for several months. Normal mining operations continued throughout the test period with minimal interruptions due to the installation and monitoring of the instruments. A computerized data acquisition system, partly underground, partly on surface, permitted continuous monitoring of data and its retrieval, display, manipulation, and storage. The finite element code used to model the test sites accounted for three-dimensional geometry, nonlinear material behavior, and the mining excavation and bolt installation sequences. Results of the test are highly variable. Comparable values between test and analysis results were obtained by applying statistical averaging of. roof test data. Results of the analyses indicate that bolts have a lesser effect on the gross behavior of mine roofs than has been indicated and that bolt load changes are strongly influenced by mining excavation sequence, bolt-placement sequence, and face distance

Jan 1, 1977

By C. Maltesh, P. Somasundaran, G. A. Gruber

Anionic conditioning of phosphate ores prior to fatty acid flotation is a critical step that determines the selectivity, recovers and, hence, the economics of the process. However, the chemical mechanisms operating during this conditioning step are not very well established. In this work, a comprehensive surrey of plant practice was conducted. Then, adsorption on flotation feed and francolite were studied under simulated plant conditions. Different adsorption mechanisms were found to be dominant under laboratory and plant conditions. In plant water, there was sonic physisorption of oleic acid on phosphate flotation feed and francolite, in addition to chemisorption. However, in distilled water under laboratory conditions, only chemisorption was detected. Fuel oil reduces the residual oleic acid in solution after adsorption, which explains the beneficial role of extender in phosphate flotation. The dissolved species in solution arising from the flotation feed or plant processing water are shown to clearly play a major role in determining the adsorption of oleic- acid on the substrates. The study also specifically demonstrates that, for the results to be used commercially, it is important to conduct the tests under plant mixing conditions and with the same plant water chemistry.

Jan 1, 1997

By Cleland N. Conwell

Intermittent coal mining has been conducted in Alaska for over a century. The first report of coal in Alaska was by the Veechy expedition of 1826 and 1827. Whaling ships used coal from Corwin Bluff near Cape Beaufort during the early and latter parts of the 19th century. The first coal mine in Alaska -- and probably the oldest in the Pacific coast of North America -- was opened by the Russians at Port Graham on the southwest tip of the Kenai Peninsula. The mine was operated from 1855 until 1867 when the United States took possession of Alaska. From 1880 to 1915 coal mining was carried on intermittently at several localities including Unga Island, Herendeen Bay, Chignik Bay, Kachemak Bay, and several points along the Yukon River. Small coal mines along the Yukon River provided fuel for the river steamers traveling from St. Michaels to Whitehorse. The area of sustained coal production began with the completion of the Alaskan Railroad from Anchorage to the Matanuska coal field in 1916 and to the Nenana field in 1918. Coal production continued to increase until 1953, at which time the oil and gas fields in Cook Inlet were developed. Oil and gas eventually replaced- the Matanuska coal as a means of providing heat and power. The military in the Anchorage area shifted from coal to oil in 1967 causing a decrease in production. The increased demand for electric power in the Fairbanks area offset the decline and coal production started to increase. In 1969-1970 the Golden Valley Electric Association constructed a mine-mouth power plant 70 miles southwest of Fairbanks near Healy and a power line to Fairbanks. LOCATION OF COALS IN ALASKA Coals are found in all geographical subdivisions of Alaska. Coal in Alaska ranges in age from Carboniferous to Tertiary, and grade from lignite through anthracite. Figure 1 shows the locations of Alaskan coal fields. The only fields that have been developed extensively are the Matanuska and Nenana. Figure 2

Jan 1, 1972

By Shouci Lu, Keji Sun, Dianzuo Wang, Yiqun Li, Chuang Jin

The dephosphorization of iron ore and reduction in Fe loss in process are currently the foremost technological challenges facing the mineral industry of Meishan Iron Ore. These problems can be resolved to a greater extent by an apatite flotation process which depends on selective flotation reagents. The primary objective of this research work is to develop new type of flotation collectors for dephosphorization of weak magnetic iron ore. Detailed discussion is given on the influence of collector dosage, pH, dispersants and pulp temperature on the flotability of apatite, siderite and hematite using the collectors of Oleyl sarcosinate(OSS), Alkyl polyoxyethylene ether phosphate (AEP) and the mixtures of OSS and AEP A key feature of the flotation was the use of the mixtures of OSS and AEP as a selective collector for phosphate. The effects of chemicals and operational variables on the phosphorus flotation from the weak magnetic iron ores have been investigated. The test results shows that floating the phosphorus minerals with new type collectors can reduce the phosphorous content in the flotation concentrate to an acceptable level of less than 0.20% P with increased Fe recovery.

Jan 1, 2002

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

By M. L. Rizzone

Since time immemorial, Mother Nature has been transporting slurries with both air and water serving as the carrier medium. Consider for example the formation of the continental shelves off our coast lines which are being formed by rivers emptying erroded land surface and depositing it into bays and gulfs. As the erosion processes take place, the fines are suspended in water which flows in streams and rivers and deposits where the velocity of the flow reduces sufficiently to allow the fines to settle out. The same process in some crude form is provided when one hoses his driveway or patio and moves dirt so as to provide a cleaning action. These examples illustrate rather crudely how the formation of slurries allows for the transport of solids. In recent years, this mechanism has become fairly well understood and slurry pipelining of many materials is now a vivid reality. The movement of liquids in pipelines necessarily occasions the use of pumps for the purpose. Those of us who have had some rub with the petroleum industry are familiar with the transport of solids through mud pumps and cementing and fracturing pumps where the movement of slurries is an everyday matter. In the drilling of an oil well the circulating fluid utilized to remove chips which are cut by a drill bit from holes drilled deep in the earth is called drilling mud. This substance contrary to what the name might imply is usually a fairly sophisticated material designed to develop certain characteristics which are desirable in the drilling process. The particles which have been cut by the drill bit are suspended in the moving column of fluid and brought to the surface and deposited. The separation of the cuttings from the drilling fluids is accomplished by the use of shaker screens and settling pits. However, it is impractical to remove the fines completely from the drilling fluid and as a result they are pumped through the mud pumps back into the circulatory stream.

Jan 1, 1969