Search Documents

By J. Kallioinen

The paper describes industrial size experiments with a 100 m3 flotation cell validating the Size Specific Flotation concept and the Tank Cell design. It discusses some variables affecting the flotation of coarse particles. The results were good. The flotation recovery of coarse particles increased up to 50%. In finer sizes the flotation improvement was 5-15% The enhanced flotation of especially the coarsest particles increased the total recovery close to 10%-units compared to conventional cells in a porphyry copper flotation. The related power draw was only 50-80% of the power of conventional cells.

Jan 1, 1995

By T. Reed Scollon

Major interrelated factors to be considered in assessing the impact of air pollution control regulations on coal are: (I) the fuel and fuel-related limitations of such regulations; (2) the rate of adoption and areal scope of the regulations; and (3) the availability of fuels and fuel-burning equipment to meet the requirements. A growing number of regulations contain provisions limiting the emissions of sulfur oxides or the sulfur content of fuels or both. With few exceptions, these limitations have not yet become fully effective in those areas which have already adopted regulations, and pertinent details of future regulations or legislation for most other areas are unknown at this time. Sufficient information is not avail- able to determine the availability of low-sulfur fuels at various demand and price levels, and large-scale commercial feasibility of sulfur-oxides removal processes and equipment is believed to be some years away. Accordingly, with the many uncertainties and unknowns, it is possible at best to make only a rough assessment of the impact of such regulations or legislation on coal.

Jan 1, 1969

Water conservation and compliance strategy can be cause for success or failure of a new or existing mining operation. Water accounting at outset, and pit and waste dump planning, may not fully consider total inflows, or sediment loads encountered during mine life. Environmental impact assessments, and permitting often dictates the rules, and these may change, to be more stringent, during course of mine development. This paper will identify techniques to control unprojected fresh water, or increased surface water flows in surface mine operations.

Feb 23, 2014

By George P. Tateosian

Merchants perform a number of functions in the copper market. As a major distribution arm of the copper industry, they secure scrap and other copper bearing materials for processing into usable refined shapes. These are ultimately sold to fabricators. Merchants ' hedging and arbitrage activities help keep values in proper relationship from product to product or region to region. Through these switching and trading operations, they optimize the flow of copper from mine to consumer. And finally, merchants act as a repository for copper units during times of surplus and a stockpile from which to draw during tines of shortage.

Jan 1, 1979

By Samuel S. Adams

Economic concentrations of potassium are essentially limited to thick, stratigraphic sections of marine evaporites. These deposits were precipitated through the evaporation of sea water in restricted epicontinental seas or in grabens related to continental margin rift systems. Following deposition the deposits were subjected to diagenesis and varying degrees of metasomatism and structural deformation. The origin and characteristics of potash deposits are easier to study and interpret than those of most ore deposits because the phase chemistry of the salt systems is known and the approximate composition of the ore-forming fluid (sea water) can be inferred with confidence. It is particularly helpful that the temperature and pressure of deposition approximated that of present earth surface conditions and the pertinent mineral assemblages can readily be duplicated in the laboratory. The study of these comparatively simple salt deposits provides examples of the practical advantages of understanding the genesis of an ore deposit. These observations, in turn, illustrate the importance of pursuing research on the more complicated magmatic, hydrothermal, and ground-water systems as a means to the more successful exploration for and exploitation of the deposits they have produced. It is the purpose of this paper, therefore, to discuss certain aspects of salt deposit geology as they contribute to exploration and mining through some understanding of ore formation. References to field examples and chemical relations in the salt systems are brief. All examples are more fully discussed, however, in the references cited.

Jan 1, 1970

By John P. Smith

As the US looks within its borders in its drive toward energy independence, economical coal transportation, particularly from vast western reserves, becomes an increasingly difficult but compelling challenge for both the country and the coal industry. Coal producers continue to develop improved technology for more efficient and cost-effective coal mining and processing. But for controlling transportation costs, coal producers must rely on a delicate balance between product demand, competition among carriers, federal regulation, and a symbiotic relationship with coal transporters. In 1981, 739 Mt (815 million st) of coal were mined in the US. Nearly 90% of this coal was moved via

Jan 10, 1982

By David B. Spencer

This paper describes a process for separating non-ferrous metals such as aluminum, copper and zinc, from other residential and industrial waste by means of permanent magnets. Although the separator may be used in the recovery of non-ferrous metals from auto scrap, most of the testing to date has been aimed at recovery of non-ferrous metals from municipal solid waste, especially recovery of aluminum from the heavy fraction of a resource recovery plant. In most resource recovery plants the incoming solid waste material is first shredded and then air classified into a light and a heavy fraction. The light fraction which contains mostly paper, cardboard, etc., can be used either as a fuel for power generation or in the production of new paper products. The heavy fraction which remains consists mostly of glass, ceramics, wood, ferrous metals and non-ferrous metals. The ferrous metals may be removed from the heavy fraction by conventional magnetic separators. After primary shredding, most of the glass and ceramic is fine in size and may be screened away leaving a residue of wood, cardboard, and non-ferrous metals. This residual heavy fraction is the input material for the separator described in the present paper.

Jan 1, 1975

By L. Gertsch, R. Gertsch

Mechanical mining is steadily gaining in usage in the mining industry. A variety of machines are now being used, including tunnel boring machines, roadheaders, continuous miners, surface miners and augers. These machines have advantages compared to drill-and-blast mining methods, including increased safety, lower cost, uniform muck size and accurately sized openings. A century of experience with mechanical methods has paid dividends to the coal industry. Current trends guarantee eventual development of true general-purpose hard-rock mechanical mining machines. When several significant challenges have been met, mechanical miners will become integrated mining systems and will determine the design of mines.

Jan 1, 2002

By E. G. Kelly, D. E. Walsh

The behavior of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effects of particle size, particle shape, pulp density, feed rate and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that, with suitable precautions, the technique is capable of providing valuable information, unobtainable from conventional studies, that could be used to better optimize spiral performance.

Jan 1, 1993

By Gerhardt A. Bennewitz

The mechanism shown here (Fig. 1) may not be all that it appears to be. To many of you it may look like a hopper car, a thing of mobility, in which you would ship coal, ores, limestone, or other bulk materials. It is approximately 50 feet long, 12 feet high, and can be placed on tracks which are on approximate 14 foot centers. But far too often in the past, and all too often today, this mechanism has been made to serve as an immobile storage box, with its primary role -- the transportation of products, seemingly incidental to the storage function. Our engineering training teaches us to conserve resources, despite some of the popular and misconceived philosophies being advanced these days. Those of you who work for companies with traffic departments know that they are always striving to reduce the price which is paid to move your mine products. Today, let's consider and analyze the ways in which the cost of transporting your mine products might be reduced, based on particular reference to coal. Bear in mind that in this context, cost and price are not necessarily synonymous. Until a few years ago, most coal and other bulk materials handled by railroads moved under standard tariff rules. These rules, which still exist today, provided transportation vehicles (railroad cars) for extended periods at no added price to the shipper or receiver. "Normal" free time rules would permit a car to be held for a maximum of 48 hours without charge; however, in the case of coal, there is a rule which, subject to liberal rules as to the

Jan 1, 1972

By V. Rajagopal

Corrosion and abrasion properties of a series of chromium-containing cast iron balls with Cr contents ranging from 0 to 29% was evaluated and compared with austenitic stainless steel and mild steel balls. Marked ball wear tests were performed on artificial ore samples consisting of 95% quartzite with either 5% pyrrhotite or 5% chalcopyrite under a nitrogen or oxygen atmosphere. The electrochemical mechanism was investigated by correlating the corrosive wear with the corrosion currents obtained from potentiodynamic polarization curves under abrasion. An offset in their electrochemical activities was observed somewhere between 16 and 26% Cr. In fact, 26 and 29% Cr cast irons showed an excellent corrosion resistance approaching that of austenitic stainless steel. Flotation recoveries were estimated on a 95% quartzite + 5% pyrrhotite sample ground with various cast iron ball materials under an oxygen or nitrogen atmosphere. Electrochemical results are found to be in good agreement with corrosive wear obtained from marked ball wear test and with flotation results.

Jan 1, 1991

By M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology for estimating gold recoveries in gravity-separation circuits is presented. The methodology makes use of a population-balance model. The model represents gold liberation, breakage and classification behavior and applies preconcentration and recovery performance curves to gravity-recoverable gold. The derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and from a projected application. The methodology makes it possible to estimate the performance of a gravity circuit having a large gold circulating load and a relatively-low unit recovery (e.g., a jig) or having a high recovery on a bleed of the circulating load (e.g., a Knelson Concentrator).

Jan 1, 1996

By P. van der Veen

There are two key reasons for this presentation: - Sustainability - Improving the economic, environmental and social impact of mining. As I will discuss in my presentation we see sustainability throughout the mine life cycle as critical for successful mine development - that is the mine makes a successful contribution to economic development and poverty alleviation for the host community and host country and at the same time the mine is a successful investment for the investor. - Knowledge Sharing ? The World Bank is not only a development bank, but also a ?knowledge bank?. One of our key functions is the dissemination of usable information and knowledge. We are here not only to share our experience but to learn from your experience as well ? two reasons that fit clearly with the mandate of the World Bank Group.

Jan 1, 2003

By Rob McIvor, Joe Keating, Gary Simmons

As more complex ores are processed, finer grinding becomes more necessary. A cross section of several industries will be presented with discussions not only of find grinding issues but also the classification of fine particles. JOHN MANSANTI: Our next topic will be fine grinding. Again, the intent is to present a topic that is generic enough to apply to multiple industries. Our first speaker is Gary Simmons. Gary is filling in for Phil Walker from Twin Creeks. Phil was not able to join us this week, because of some issues they're having with the autoclave. Gary, being involved in the development phase, is very familiar with the topic. Gary spent about three years with American Cyanamid and another four years with Noranda. He also spent some time with Meridian Gold, then became the director of metallurgy with Santa Fe Pacific Gold. He spent seven years there and is presently the director of process technology with Newmont Gold.

Jan 1, 1998

By Ian Longson, Darron W. Dixon

This paper describes the results of an investigation into the application of a statistical method for the prediction of general air-body methane concentration in longwall coal districts. An important and necessary part of the research was the acquisition of representative monitored mine environmental and coal production data. The monitored data was used to build time series models of general air body methane concentration, air velocity, barometric pressure, coal production and methane drainage variables of differing timescales according to the Box-Jenkins method of time series analysis. The univariate models were used to identify causal relationships between methane concentration and its explanatory variables. Coal production was found to be the dominant variable in the determination of the quantity of methane emitted and where appropriate, multivariate time series models were built in which expressions for methane concentration in terms of coal production were obtained. Finally, forecasts of methane concentration values were generated from the multivariate models to determine their forecasting capabilities.

Jan 1, 1993

By Allan Gebhard

The purpose of this paper is to summarize the role of water resource monitoring in mining activities and to discuss the considerations that go into designing and implementing a monitoring program. The design of a monitoring program is invariably based on sound engineering and scientific judgement since no design formulas exist that can be universlly applied to the monitoring of all activities. As discussed in this paper, however, a methodology of designing a water resource monitoring program does exist. In order to cost-effectively monitor the water resource impacts of mining activities, the following three monitoring related items should be understood: 1. the role of water resource monitoring in the planning, construction, and operational stages of mine development, 2. the available water resources monitoring methods and the proper role of each method in the various scages of mine development, and 3. the strategies that should be followed in designing and implementing a water resource monitoring program.

Jan 1, 1976

By M. J. McPherson, P. Mousset-Jones, G. Danko, I. M. Konduri, F. Calizaya

The flow of air through a bare rock, underground airway is affected by the size and frequency of the micro- and macro-asperities of the rough surface. The focus of this study is to characterize this roughness using the coefficient of friction, the friction factor and the fractal dimension. The rough surfaces were identified by two sets of 177 and 78 transverse profiles measured by a laser profiler along the length of an underground airway at the Sunshine Mine, Idaho. Based on the measurements, the friction factor was estimated from Atkinson's equation and the coefficient of friction from the Moody diagram, and power series and variography were used for computing a fractal dimension for the airway surface. Significant conclusions are reached relating the effect of error in the measurement of cross-sectional and rubbing surface areas of a drift, on the estimated friction factor for the airway. The potential role of the fractal dimension as an alternative to the friction factor for characterizing the roughness of a mine airway is discussed.

Jan 1, 1993

By Joseph Corvetti

This paper is of conceptual nature. The authors present their idea of creating an integrated and intelligent excavation design system. Research work has just been started and the results will be addressed during presentation of this paper. The authors are currently engaged in a pilot study and expect to build a feasibility prototype expert system (establishing the numerical-cognitive coupling in excavation design) by the end of this year.

Jan 1, 1996

By P. Eger

Minnesota contains a major low- grade copper-nickel sulfide resource within the Duluth Gabbro Complex. Several companies have actively explored this resource. Open pit mining would be required to develop portions of the resource, and as a result, large quantities of sulfide-bearing lean ore and waste rock would be stockpiled. Although the problems associated with high-sulfide tailings and acid mine drainage are well documented, the leaching characteristics of low-grade mineralized stockpiles must be understood for environmental impact assessment, siting, and planning. The Minnesota Department of Natural Resources and AMAX have cooperated in a research program to study leaching and revegetation -of test stock- piles, Six small (1600 'tons) stockpiles were constructed at the MINNAMAX Project Site and they range in composition from 0.29 to 043 g % copper, 0.075 to 0.09% nickel, and 0.6 to 1.45% sulfur. Two of the stockpiles were covered with mineral soil, one was covered with topsoil, and three were not treated Revegetation plots were established on the piles which received a soil cover. Leachate samples and flow measurements were collected at the base of the piles. Initial results indicate that metal concentrations in leachate samples range from 10 to 10,000 times the concentrations found in the streams of the area. During the first growing season, the test pile covered with topsoil yielded 30% less water than untreated test piles. No reduction in yield was observed for the piles that were covered with the less fertile mineral soil. First-year vegetative growth, expressed as biomass, was four times greater on the-topsoil pile than on the mineral soil piles. The long-term effects of vegetation on leachate quantity and quality continue to be investigated.

Jan 1, 1980

By N. N. Clark, C. M. Atkinson

Pachuca tanks are used widely in the mineral industry for leaching and mixing operations. An analysis has been presented previously to predict circulation of homogenous slurry in Pachuca tanks with full height draft tubes. However, settling of solids causes deviation from the homogenous case. Circulation of settling slurry in a Pachuca tank is modeled and shown to be a function of settling velocity, solids fraction, solid and liquid density, air flew rate, and tank dimensions. The pressure balance is shown to be very sensitive to these parameters, especially at low slurry velocities. Equations for predicting the air requirements in Pachuca tanks containing settling solids are presented.

Jan 1, 1988