Search Documents

By A. Russell, M. N. Hughes, Jack Barrett

The bacterial oxidation of arsenopyrite has been shown to be an efficient, economic and environmentally acceptable method for the liberation of any gold content . The mechanism of the process is not certain but is usually considered to involve direct and indirect reactions with respect to bacterial involvement. The direct reactions are those in which the bacteria attached to the mineral surface cause its dissolution, with dioxygen being the oxidant. The iron(III) produced in solution is the chemical oxidant in the so-called indirect reactions. Barrett et al 2 showed that a synthetic bio-oxidation solution (with no cells present) could dissolve up to 15% of an arsenopyrite sample, the products of the chemical oxidation being iron(II) and arsenic(III). This paper describes an extension of the investigation of the chemical process and its imp! ication for the mechanism of the bio-oxidation of arsenopyrite.

Jan 1, 1990

By Kenneth B. DeGraaf

The development of precious metal recovery processes using chloride systems has mostly evolved from the development of chloride based treatments for base metal concentrates or ores. The recovery of silver from chloride solutions within a process designed for the treatment of base metals usually is part of a solution purification stage. This paper discusses the development of the silver recovery stage used in the GCM HydroCopper process.

Jan 1, 1990

By John E. Litz, Charles W. Kenney, Wayne Carter

Refractory gold ore pretreatment processes continue to receive much attention. This paper compares the relative economics of treating ores by oxygen pressure oxidation, roasting and bacterial oxidation with or without preconcentration by froth flotation. Capital and operating cost estimates for each method of pretreatment were prepared and these estimated costs and ore sulfide grades then are used to compare the process economics. The study indicates that the most significant item affecting the economics is the amenability of the ore to flotation. The cost benefits of flotation are $10-13 per tonne ore processed (2%-4% s=, 10:1 ratio of concentration). In most cases bacterial oxidation has the lowest overall cost, especially if less than complete oxidation of the sulfides will give acceptable recovery, however bacterial oxidation has yet to be practiced on a large scale. In all situations pressure oxidation shows the highest cost. However, the cost differences between the treatments are small, less than $7 per tonne.

Jan 1, 1990

By Leslie C. Thompson

The heap leach process used for recovering gold from oxide and sulfide ores is operated as a closed circuit system in which the cyanide process solutions are continuously recy­cled. In a well-designed operation there is little or no dis­charge of cyanide to the environment. Spent leached ore residues are water washed to remove most of the trace cyan­ides and precious metals remaining after completion of cyan­ide leaching. After the washing step, small amounts of cyanide, metal-cyanide complexes and nitrates remain in the residue. Most of the cyanide and nitrate residue constituents exist in the pore water of the spent ore rather than in the solid mineral fraction. More than 90% of the complexed cyanides in a freshly washed ore residue are present as free cyanide or weakly complexed metal-cyanides. Natural volatilization and decom­position rapidly remove most of these easily dissociable cyanides from the spent ore. Only the stable, strongly com­plexed metal-cyanides, such as gold, cobalt or the ferrocyan­ides and other constituents such as nitrates have a long term persistence in the spent ore residue (Towill et al). Despite washing and natural removal mechanisms, spent ore has the potential to act as a point source of com­plexed cyanides and nitrates for soil and groundwater con­tamination if inadequately contained (Huiatt et al). The groundwater contamination is caused by the leaching of the soluble cyanide compounds and nitrates from the pore water of the residue.

Jan 1, 1990

By Trent Temple, Curtis Johnson, John Mudge

Newmont Gold Company uses centralized carbon handling facilities to strip loaded carbon from five mills and four leach facilities located along a 38 mile stretch of the Carlin Trend in Nevada. Both Zadra and AARL elution processes are employed at this centralized facility which is located near the company's Gold Quarry operations. The Zadra elution circuit was commissioned in 1985 and later expanded in 1987. This circuit can strip carbon at a rate of 24 tons per day. The AARL elution circuit, commissioned in 1988, also has the capacity to strip 24 tons of carbon per day. Two horizontal, rotating, regeneration kilns are used to reactivate approximately 60% of the stripped carbon before it is returned to the mills or leach facilities. One kiln is located in the Zadra plant, while the other is located in the AARL plant.

Jan 1, 1990

By E. Haug, Quamrul Ahsan, R. Norcross

Cyanide leaching is the most common process employed in the majority of the gold extraction plants. These gold extraction plants naturally generate tailings and/or effluents that contain highly toxic cyanides, In geographic locations with excess precipitation and therefore net positive water balance, a portion of these tailings must be discharged. Before these highly toxic cyanide-containing effluents can be discharged to the waterways, cyanide and any other toxic substance must be destroyed. Geographic locations with high evaporation and low precipitation, as in the western USA, result in net negative water balance and therefore these plants can operate with a zero discharge option. However, with the current stringent environ­mental regulations and concerns for bird and wildlife mortality, even these operations may be required to partially treat their tailings to preclude potential harm to wildlife. Furthermore, heap leach opera­tions are now generally required to detoxify the heaps before abandonment. It is, there­fore, apparent that all gold extraction plants may be required to install some form of effluent treatment in order to achieve the above objectives,.

Jan 1, 1990

By P. G. Semple, K. W. Major, P. Eng.

The recent increase in development of refractory gold deposits has resulted in changes to the traditional treatment processes. The selection of the preferred refractory treatment process is dependent on the mineralogy of the ore. One process, which has recently gained increasing attention, utilizes dry grinding and roasting of the whole ore. This paper will discuss some of the considerations to be addressed during the design of the process fl owsheet and what the effects of the various alternatives will be on the plant capital and operating costs. The paper will be based, in part, on current experiences with dry grinding, roasting plant design and start-up.

Jan 1, 1990

By Joe D. Allison, Tom D. Baugh

The analysis for total cyanides (CN, or the cyanide due to the combination of free, weakly associated and refractory cyanide complexes) is required by most regulatory agencies for determination of effluent compliance. This method requires a distillation of the sample at low pH's and is most often sent to contract laboratories at a high time and monetary cost. This paper describes a new micro­distillation apparatus which allows for a multiple of CN,"' analyses to be carried out simultaneously saving both time and money. It can be used in the field, since only electrical power is required for the method. While not being appropriate for reporting values to the respective regulatory agencies as of yet, it is quite valuable for screening a large number of samples prior to submission of the samples to a contract lab for "official" reporting.

Jan 1, 1990

By S. K. Bhatt

This paper reviews major developments in continuous haulage technology for underground coal mines. Haulage systems, both in use and development, are investigated through a comprehensive literature search and visits to mines and manufacturers. The systems include flexible conveyor train, mobile conveyor, multiple-unit continuous haulage, extensible, and belt turning systems. Strengths and weaknesses of the systems are assessed in light of their operating under remote control and their application to the computer-assisted continuous mining machine being developed by the U.S. Bureau of mines. Through mining scenarios, candidate haulage systems are conceptualized to be consistent with the capabilities of the mining machine.

Jan 1, 1990

By R. Bhaskar

An airborne dust cloud is an ensemble of particles of varied size, density, shape and states of aggregation. An understanding and quantifying of the dispersion and deposition of the dust generated in mines is essential to the development of measures for reducing worker exposure to dust. In coal mining, the major portion of the dust is generated during the cutting of coal using either a shearer or a continuous miner. The major phenomenon affecting ambient concentration is the deposition of dust. Particle deposition may take place due to the effect of gravitational, inertial, electrostatic, and thermal forces, and mechanisms such as Brownian and eddy diffusion, and inertial impaction. The three major mechanisms of deposition in turbulent flow in mines are diffusion (Brownian and eddy), sedimentation and inertial impaction. The mechanisms determining particle deposition are size dependent.

Jan 1, 1990

By C. J. Johnson, C. J. Bise

Coal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation's deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only after ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental compositon of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines. There are several potential contributions of this type of study to the coal mining industry. First, after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies. Further. assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location, a mining company could predict anew mine's respirable dust elemental composition in the immediate ventilation return by using exploratory drill core samples of the roof, coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design. much time and money could be saved. Scope of work To investigate the variability of the chemical characteris tics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and midwestern United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee (1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs. The procedure that was used to produce the laboratory generated respirable dust was based on the Hardgrove grindability test since it reflects the pulverizing characteristics of coal. This test was chosen for several additional reasons. First, it is repeatable and reproducible. A consistent amount of input energy is used as well as a specified size range of feed material to be crushed (the channel samples). Second, it is thought to generate secondary dust in a way similar to that of the crushing and grinding of the coal and rock as they pass through the arc-shaped cutting path of the CM's cutter head. The potential effect on dust generation by this secondary grinding mechanism may be at least as much as that produced by primary fragmentation, which is dust produced by the cutting action of the bit against the coal or rock (Roepke. 1984). Finally, the Hardgrove grindability test is well known and is used in the coal industry to guide mineral processing engineers in estimating the capacity of mills used to grind coal. One hypothesis of dust researchers in the Generic Technology Center for Respirable Dust is that the elemental as well as the physical characteristics of coal mine dust will make a difference in the incidence and severity of CWP. Coal mine dust is generated not only from coal, but also from any rock partings contained within the seam or any roof or floor material mined with the coal. Thus, coal mine dust may not have the same elemental characteristics as the coal being mined. Given that hypothesis, mixtures proportional to each thick¬ness mined of roof, coal, and floor rock derived from the channel samples of the face areas from which the respirable dusts were generated by the CMs were used to produce the feed material that was pulverized in the Hardgrove machine.

Jan 1, 1990

By R. A. Haney

The Mine Safety and Health Administration (MSHA) has conducted studies both in coal and noncoal mines to evaluate methods for sampling and separating diesel particulates from mineral dust aerosols. The agency is investigating size separation techniques to distinguish between diesel particulate and respirable coal mine dust. Additionally, ashing techniques have been used to distinguish diesel particulate from mineral dust in metal and nonmetal mines. As part of these studies, personal exposures to diesel particulate for various mining occupations have been measured. This paper describes the measurement techniques and summarizes the exposure levels for various underground mining operations.

Jan 1, 1990

By R. E. Krauss

The McLaughlin Mine is a world class epithermal gold deposit located in the coastal thrust fault of Northern California, U.S.A. Homestake adopted a proactive strategy in the permitting of the Mine. Extensive environmental base line studies were undertaken. Engineering and process alternatives were evaluated for environmental impact along with other factors. A unique pressure oxidation process was selected. Screening studies were conducted as a basis for the selection of waste rock and tailings disposal sites. Project engineering and permitting were fast tracked. Construction required eighteen months and the first gold bar was poured in Parch of 1985, six years after the initial discovery. Project facilities are designed and operated so as to minimize environmental impacts. A comprehensive monitering program demonstrates permit compliance. Reclamation of the site is ongoing throughout the Mine?s twenty year life. Non-mined lands are managed to maximize wildlife habitat value.

Jan 1, 1990

By R. W. Waytulonis

New exhaust control techniques and devices may be necessary to meet future diesel particulate matter emission standards in underground coal mines. This paper reviews conventional work practices and devices used to control diesel exhaust emissions, and new techniques being tested by the Bureau of Mines. Discussions will center on important work practices and on the function and efficiency of exhaust after-treatment devices. An industry/government cooperative research project to develop and test an exhaust after-treatment system for part 36 equipment is also discussed.

Jan 1, 1990

By N. B. Aughenbaugh

Compacted clays are used as permeability barriers in many mineral engineering projects such as heap leaching, containment ponds, tailings disposal and earth dams. Source materials used for clay liners include a wide variety of sand, silt and clay admixtures that exhibit dramatically different engineering properties when densified. The permeability and plastic properties of fine-grained soils are reviewed with respect to the state of compaction as the water content varies. Be-cause they are weak in tension, compacted clays are susceptible to cracking when subjected to differential flexural movements. Designs of compacted clay liners must include an evaluation of their flexibility which is the ability of a fine-grain soil to bend plastically without cracking. This paper will also discuss the importance of flexibility with respect to soil types, compaction effort, failure mechanism and testing evaluation to the performance of clay liners in preventing seepage of pollutants from a containment site.

Jan 1, 1990

By J. Mark Richardson

The use of an integrated software package to simulate and optimize the performance of mineral processing circuits is illustrated by three examples. Each represents application of the software and associated techniques to optimization of an existing plant. In the first example, a South-western U. S. copper company employs the method to simulate and improve performance in crushing, screening and SAG milling. A second copper producer evaluates equipment changes and flowsheet alternatives in a closed-circuit ball mill-cyclone operation. A Southeastern U. S. aluminum refinery optimizes performance of a dry milling and classification circuit for production of carbon particles used in anode casting. Graphical and tabular data describe the circuits simulated and the results achieved in each example.

Jan 1, 1990

By J. K. Shurie

Calcined high quality bauxite is a staple raw material of the abrasive industry world-wide. The author discusses the factors which affect the economic value of calcined abrasive grade bauxite, and proposes an approach to the problem of estimating the relative value of available materials.

Jan 1, 1990

By V. E. Housman

EPA's Office of Solid Waste (OSW) is developing a program, under Subtitle D of the Resource Conservation and Recovery Act (RCRA) to regulate the management of non-coal mining wastes. In May 1988. OSW produced a "Strawman", which is a working document that is precursor to a proposed rule. OSW has been working closely with environmental groups, industry, and States to solicit comments and feedback on the mining waste program. OSW currently plans to release a second "Strawman" in early 1990. A proposed rule is tentatively scheduled to be published in the spring of 1991.

Jan 1, 1990

By T. McWaters

Miami Copper Company began a block-caving operation in 1911 using a gravity mill to separate copper minerals from the Pinal Schist host rock. The tailing was deposited by the upstream method using perimeter launders and spigot valves in six canyons adjacent to the mill until 1932. In 1928 the larger and more distant Solitude tailing pile was developed which by 1932 was receiving all tailing except for upsets. In 1925 Miami Copper converted its gravity mill to flotation which began to produce higher sulfide copper recoveries.

Jan 1, 1990

By C. N. Logan

The Southern Company is one of the nation's largest electric utilities and is the parent firm of five operating companies: Alabama Power, Georgia Power, Gulf Power, Mississippi Power and Savannah Electric and Power. Another subsidiary is Southern Company Services (SCS) which provides engineering and technical sup-port to the five operating companies. This technical support includes the procurement and supply of over 40.9 Mt (45 million st) of coal annually for the 22 coal fired plants in the system. Approximately 80 percent of this tonnage is purchased under long term contracts and the remaining 20 percent is purchased on the spot market. The coal is principally supplied from Alabama, Illinois Basin and the eastern Appalachian coal fields. Most of the coal is delivered by unit train and barge but one plant in Alabama receives all its coal by truck and conveyor belt.

Jan 1, 1990