Search Documents

By R. W. Bartlett

Aeration curing, over- a long duration in wet- red stockpiles, shows promise as an affordable pretreatment method for oxidizing gold encapsulating sulfide minerals, and possibly organic matter, in low grade refractory ores. Following aeration pretreatment, the ore is reclaimed, neutralized, and cyanide leached by conventional practices. Large tonnages of subeconomic material, including mine stripping waste, may he converted into ore by this new technology. The results presented show that a successful application of this technology will likely require crushing to about -2 cm (-3/4 in.), followed by aeration in a wet stockpile for long periods, up m three years. Natural convection may he inadequate, hut forced air ventilation, at modest pressures and power consumption, is affordable.

Jan 1, 1991

By Robert W. Bartlett

Heap biooxidation of sulfidic refractory gold ore requires large amounts of oxygen, as shown in Figure 1. Bacteria, Thiobaci/lus ferrooxidans, are donnant at oxygen concentrations below about 3% in air (1 ppm in aqueous solution) because ofmonod kinet­ics. Hence, the maximum possible utilization is only about 75%, and it may be much less than that due to poor air sweep effi­ciency. At the maximum oxygen utilization, an ore containing two percent pyrite requires nearly 100 cubic meters of air per tonne (4,000 cubic feet per ton). The stoichiometric air require­ment to oxidize arsenopyrite is similar to that of pyrite. While the leaching solution percolating through the heap introduces some dissolved oxygen, the amount is insignificant because of the low solubility of oxygen in water, 7 to 8 ppm at atmospheric saturation. There are only three ways to provide oxygen to the heap: either air flow by natural convection, diffusion of oxygen from the surface (through stagnant air in the air-filled void space in the heap), or forced air ventilation of the heap. Each of these processes will be reviewed.

Jan 1, 1996

By A. Goulsbral, D. Harrison, R. Dunne

A programme to reduce cyanide consumption at the New Celebration Gold Mine, situated 32kms South of Kalgoorlie, Western Australia, commenced in the latter part of 1990. Cyanide speciation studies at the time identified that the major loss and consequently consumption was due to the hydrolysis of cyanide, The use of artesian hypersaline waters of high magne­sium content on gold plants in Western Australian Goldfields has meant that economically viable operating pH values during cyanide leaching are around 8.9 to 9.5. The high ionic strength in these waters does to some degree retard the hydrolysis reac­tion. Notwithstanding this, the formation of hydrogen cyanide and its loss due to volatilisation is the cause of the major loss of cyanide on most gold plants in the Kalgoorlie Goldfields. This paper discusses the aspect of oxygen addition during cyanide leaching to decrease cyanide consumption and increase gold recovery.

Jan 1, 1996

By Pierre Filiatreault, Brian Straight, Stephanie Thibeault, Devin Castendyk, Londie Cameron

"Working on or near water at active, closed or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the U.S. Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at U.S. metal, non metal and coal mines (MSHA, 2000). Openpit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including: a) drowning, b) hypothermia, c) falls to the ground from the top of high walls, d) collapse of unstable access roads, e) rock falls and avalanches from pit walls, f) avalanchegenerated tsunamis traveling across the lake surface and g) rapid degassing events.Some pit lakes are simply not safely or easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on a regular basis is needed to monitor the evolution of water quality over time, verify the accuracy of numerical predictions and, ultimately, manage lake water chemistry and ecological risks. For pit lakes with surface water discharge, regular monitoring is used to appropriately design and adjust water treatment plants in order to produce acceptable site discharge water quality.As a product of these risks and the need for water samples, mining companies spend considerable expense on pit lake safety as part of monitoring programs. This includes training personnel for on water duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices and cold-water clothing called mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface and employing spotters who can directly communicate with emergency medical services to watch sampling activities because cell phones and radio signals can be blocked by pit walls. Some sites utilize redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires two boats on the water during pit lake sampling events, with a third boat on the shoreline, gassed and ready to go. In addition, water samplers are required to hold Marine Emergency Duties training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel in the event of an accident."

Jan 7, 2017

By S. Thibeault, P. Filiatreault, B. Straight, D. Castendyk, L. Cameron

"Unmanned aerial vehicles (UAV), or drones, capable of collecting and retrieving water samples from pit lakes, tailings ponds and other mine water basins will revolutionize environmental programs by lowering sampling costs and reducing safety related risks. Costs typically include a boat and associated equipment, boat transportation, road maintenance, water safety devices, water safety training, and additional staff. Typically, the total cost can exceed $20,000 USD per sampling event (excluding lab analyses). Hazards include potential for drowning, unstable pit walls, and unconsolidated sediment surrounding tailings ponds. Hatch has developed a novel device for aerial drones which currently enables the collection of water samples from depths up to 390 ft (119 m). This system only requires a pilot, a sample technician, and a safe operations point overlooking the water body. Hatch anticipates this will reduce monitoring cost by at least 50% while improving safety, reducing staffing requirements and accelerating data acquisition. This manuscript demonstrates profiling and sample collection from a 95 ft (29 m) deep reservoir and a 377 ft (115 m) deep pit lake, and highlights the potential of this emerging technology. INTRODUCTION Working on or near water at active, closed, or abandoned mine sites is inherently dangerous. Between 1996 and 1999, the United States Mine Safety and Health Administration (MSHA) reported 17 fatalities involving drowning at US metal, non-metal, and coal mines (MSHA, 2000). Open pit mines which fill with water following mine closure, called pit lakes, present numerous risks to environmental monitoring teams including drowning, hypothermia, falls to the ground from the top of high walls, and rock avalanches resulting from steep, unstable pit walls. Some pit lakes are simply not easily accessible for ongoing monitoring. However, the routine collection of water samples from the entire water column on at least an annual basis is required to monitor the evolution of water quality over time, to verify the accuracy of numerical predictions, and to manage lake water chemistry in order to produce “treatable” influent to water treatment plants, and ultimately, produce acceptable site discharge water quality. As a product of these risks and the need for water sample, mining companies spend considerable expense on pit lake safety as part of monitoring. This includes training personnel for “on water” duties and hazards, purchasing or hiring specialized equipment and personnel (such as boats, boat operators, personal floatation devices, and mustang suits), stabilizing pit walls and maintaining safe access roads to the lake surface, employing spotters with direct communication to emergency medical services to watch sampling activities (because cell phones and radio signals can be blocked by pit walls), and utilizing redundancy to prepare for unexpected incidents and accidents. For example, one Canadian mining company requires pit lake water samplers to hold Marine Emergency Duties (MED) training to ensure the entire boat crew is sufficient and competent for the safe operation of the vessel, and uses three boats for water sampling: two on the water at all times, and one on the shoreline, ready to deploy. The costs of these safety mechanisms greatly adds to the overall expense associated with pit lake sampling. Consequently, environmental programs may need to reduce the frequency of pit lake sampling in order to keep monitoring programs within an acceptable budget"

Jan 1, 2017

By Henryk Bystron

The underground fire areas are formed as a result of failure of an active fire extinguishing in mines. Such areas bring about a fire hazard for the work safety and for the mining operations. For liquidation of fire areas it is necessary to create conditions under which a possibly small amount of air is flowing to the fire. To achieve this end, isolation methods are used which consist in erection of full stoppings of various types, sealing practically the fire areas. These methods usually fail in oases when the coal seam is thick and the fire area is situated between the intake shaft and the outtake shaft in which a high-pressure fan is in operation. In such oases ventilation methods based on the balance of aerodynamic potentials in fire areas are to be used. For a very long time the isolation and ventilation methods have been developed in the world mining, No sooner than since 1980 the aerodynamic potential has been used in ventilation methods [1,2,6]. So far, the aerodynamic potential was called in different ways and was determined by different formulae which gave its numerical values more or less approximative. Nevertheless, even in situations featuring by a lack of sufficient theoretical bases of the aerodynamic potential the ventilation methods brought considerable profits in the field of safety in mines and of economics in mine ventilation [1-6,9,10]. The increase in the depth of underground mines and their equipment with expensive machines (apparatus) brought about that the Central Mining Institute at Katowice undertook research works which are crowned by the theory of the aerodynamic potential in mine ventilation networks [7]. The use of this theory in the mentioned ventilation methods will increase their effectiveness. Since the theory will be published in the III rd quarter of this year, we cite in the present paper the formulae and relations associated with this theory which are indispensable to present the balance of aerodynamic potentials in the fire areas in their control by ventilation methods.

Jan 1, 1980

By S. J. R. Lowrie, J. S. Edwards, A. D. Jones

A small scale model has been constructed to simulate air and gas flows on a full scale retreat longwall coal face. Scaling relationships were derived to define how the main aerodynamic properties of the full scale could be preserved in the small scale model. These scaling requirements include: a minimum value for the Reynolds number for the flow on the face in order to maintain turbulent flow with a constant non-dimensionalised coefficient of turbulent dispersion; a constant Richardson number to maintain similitude for the formation of layers of buoyant gas; scaling of the permeability of the waste so as to obtain the same proportion of seepage flow through the waste; pressure gradients due to the ventilation and to the density difference (between the air and the gas layer) were kept in proportion; and in the waste, the relative contributions of inertial dispersion and molecular diffusion were approximately in proportion. The complementary roles of computational fluid dynamics (CFD) and aerodynamic scale models for simulating mine ventilation are discussed. The physical model is described and an example presented of simulations of the effect of changes in mining condition on the effectiveness of gas control in retreat longwall coal faces.

Jan 1, 1995

By Ezz El Din Abdel Hakim Khalaf, Khalid S. Essa, Marc Munschy, Mohamed A. S. Youssef

This study focused on joint interpretation of the aeromagnetic and radiometric data to allocate and describe the structural elements and mineralization zones such as uranium, gold, and sulfide in the Gebel Umm Tineidba and its surroundings, Eastern Desert, Egypt. The study region is covered by exposures of Precambrian rocks such as gneisses, migmatites, ophiolitic mélange, metavolcanics, younger granites, and Quaternary sedimentary covers. The application of the total intensity magnetic and reduced-to-pole maps, power spectrum, analytic signal, tilt-angle, and local wavenumber maps helps in recognizing magnetic sources distribution, lineament features, and mineral zones delineation. The obtained results indicate that the depths of the deeper NE–SW, NNE–SSW, and N–S trending structures extend from 400 to 1750 m and shallower ones range from 100 to 400 m. Finally, the main trends of these structures affect the probable mineralization zones.

Sep 22, 2022

By David L. Daniels

The U.S. Geological Survey has for many years been flying and compiling aeromagnetic surveys. The aim is complete coverage of the United States, about half of which is presently done. Colored aeromagnetic maps at a scale of 1:1,000,000 are published as the states are completed; Minnesota and Colorado have been published. Michigan, Iowa, Nevada, Utah, Maryland and Virginia are presently being processed. Some of the most spectacular data collected to date is from the Piedmont of the Eastern United States. I am going to discuss a preliminary aeromagnetic map of the Piedmont region between New York and North Carolina, where coverage is nearly complete. This map has been compiled from many surveys. Flight spacing over Piedmont rocks is 1/4 to 1 mile with flight elevation of 500 feet above ground. The spacing over the Virginia Coastal Plain and Valley and Ridge regions is wider at 2 - 3 miles. Much of the data in Virginia has been produced by the Virginia Division of Mineral Resources. The map is colored on a spectral color scheme with red for the higher intensities and violet the low intensities. Each color represents a 100 gamma interval. Some of the highest intensities are beyond the range of the 13 colors - these are left white. It is necessary, of course, to remove first, the Earth's main magnetic field. The Geological Survey uses the International Geomagnetic Reference Field or IGRF (Fabiano and Peddie, 1969). The use of color in aeromagnetic maps is not new, but then not common. We have found that colored aeromagnetic contour maps are more useful by far than the uncolored versions because they allow the user to instantly compare intensities in widely separated areas and visualize long wavelength anomalies even when numerous short wavelength anomalies' are superimposed. One tends to see only steep gradients on uncolored aeromagnetic maps, the broad anomalies being quite invisible. We feel that colored maps take the place of various mathematically derived maps such as second derivative or averaged maps.

Jan 1, 1973

By P. A. Meyer

The Tenmile Range is a north trending zone of high relief within the central Colorado porphyry-mineral belt, located between Leadville and Breckenridge. (Figure 1, the Index Map of the area surveyed.) The Climax mineralized zone is located at the southern end of the range on the northwest side of the Continental Divide. This portion of the total area surveyed will be discussed in detail today. A fixed wing aeromagnetic survey was flown over this range and mineralized zone in the fall of 1957. The survey was run as an experiment to see if a useful geophysical tool could be applied in the exploration for similar type deposits. The purpose of this paper is to describe the results of this survey and the approaches used to aid in the interpretation of the total intensity data.

Jan 1, 1968

By Mary Fu, Helen Leung, Colin R. Phillips

In uranium mines, the median size of the aerosol has been found to be about 0.1 micron or less. Such small aerosols are readily deposited or "plated-out" on dosimeter interior surfaces resulting in the recording of a low dose. The "plate-out" properties of the CEA alpha dosimeter head are described with respect to aerosol properties in controlled experiments in the laboratory. A simple model is derived to estimate the amount of "plate-out" in the CEA head.

Jan 1, 1981

By James W. Bass

Atmospheric fluidized bed combustion (AFBC) is an improvement in coal-fired boiler design that offers several advantages over conventional boilers. AFC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling which can, in turn, increase a boiler's fuel flexibility. This report discusses, in general, AFBC technology and, in particular, progress at the 20-MW Pilot Plant built by the Tennessee Valley Authority (TVA) at its Shawnee Power Station near Paducah, Kentucky.

Jan 1, 1985

By F. Heivilin

Little did I know, in 1977, that when the A. P. Green Refractories Raw Material Manager showed me 5-6 burlap bags with samples of calcined high alumina bauxite in their testing lab that this was the start of China moving to be the number one user and producer of calcined refractory bauxite. According to Ted Dickson in his August 2008 Industrial Minerals article China produced about 4 million tons of calcined bauxite in 2007 using 2 million tons themselves. They imposed an export limitation of 970,000 tons in 2007 and 940,000 tons in 2008. A 10% growth will take up the difference between exports and production in 4 years. Two of these years are gone. It will take only 4 more years to eliminate the export quota in home use. Then they will be importing unless they increase production. Guyana was exporting over a half million tons in 1975 and sold less than 70,000 tons in 2002. Basai Metals Group bought Guyana?s deposits and is rose to 250,000 tons in 2007 and expects to produce 280,000 tons in 2008. PRICES According to the USGS Prices dropped from $172/per ton for Guyana calcines in 1980 just after the start of Chinese production to $122 in 1985. Guyana prices averaged around $120/ton from 1985 to 2005. China?s price dropped as low as $45/ton in 1995 undercutting Guyana and making it virtually impossible for anyone to get into the market. The price suddenly escalated to $550/ton FOB China in the summer of 2008 when China actually cut its exports in half. The price dropped in the fall as orders dropped. This is a four to five fold price increase. Is this a shortage of bauxite or a monopoly? Australia dropped out of the market in 2008 and Surinam, controlled by Alcoa, is not participating right now. Will these two come back in to make up the difference? Will the price hold up so they can make a profit? [ ] The low prices have undoubtedly affected the prices of the 60 and 79% alumina bauxite which can hold down the quantity of 80% plus calcined refractory needed in the world market. China is starting to upgrade lower quality bauxite up to 90% alumina. With high prices kaolin alteration to high alumina comes into play. The calcined bauxite is also used for proponents, Brown fused alumina, and abrasive grades which compete with Refractories. These and the tightness of supplies needed for metallurgical will hold prices up. TONNAGE China is the number one supplier and consumer of high alumina calcined bauxite in the world. Basai Metals Group Guyana (BMGG) is owned and controlled by Basai Minerals Group of China. This appears to be the second largest supplier. Australia has dropped production and Brazil is just starting to expand. It appears China is going to replace some of exports caused by the Export License 940,000 ton maximum in 2008 by raising Guyana?s (BMGG) production of calcined refractory grade bauxite. Companies exceeded restriction in 2007. Fines have been imposed for 2008. In August 2008 they appear on line to meet the 2008 quota. After August prices have dropped off as orders dropped due to the recession. Guyana was the largest producer in 1975 with 769,000 tons which decreased to less than 79,000 tons in 2002. The U. S. is a small part of the world production. I have used the United States charts to represent world imports because I have little data on what other countries import and pay FOB for their bauxite. China started exporting calcined 80% plus refractory bauxite to the United States in 1979 with 24,000 tons. By 1985 they were the number one importer with 169,000 tons. Guyana who had been number one in shipments to the United States gradually decreased to 36,000 tons in 2006. Guyana has been purchased by China BMGG and will increase there production to over 200,000 tons in 2009. Australia shut down production in 2008 and Surinam has elected to not send any Calcined bauxite to the United States. Imports to the United States from 1978 to present are as follows: [ ] Refractories are important because they affect 96% of the GNP. During the cold war we had stockpiles of 80% refractory grade bauxite

Jan 1, 2009

By J. Katzur

Recently in Germany, novel artificial humus in combination with water-storing hydrogels has successfully been tested as soil improving material in pot experiments. The novel artificial humus (NOVIHUM®) is derived from lignite through oxidative ammonolysis. The product contains c. 5.5% nitrogen. Using NOVIHUM® as fertiliser, variable amounts of the contained nitrogen are gradually available to the plant, depending on the hydrolysis rates of the different N-compounds. NOVIHUM® is a unique combination of long-term fertiliser and stable humus. The tested hydrogel is a polyacrylate/poly-amide copolymer, which is able to improve the water holding capacity of the soil and to retard significantly desiccation. In May 2000, in Germany (Aue region), an experimental site was set up under extremely difficult growing conditions for trees (Quercus petraea) on a uranium spoil pile of the mining company WISMUT Ltd. The oak plots treated with NOVIHUM® and hydrogel showed increased total increment-values, which mainly are the result of the second growth phase. Obviously, these plants profit from the favourable physical parameters of the substrate and the use of the novel artificial humus as nitrogen source. The oak trees can better use the plant-available NH4-nitrogen released from the artificial humus during the planting year. In Greece, an experiment was set up in December 2000 aiming to the afforestation (Pinus nigra, Abies cephalonica) of a bauxite spoil pile of SILVER & BARYTE ORES MINING Co. S.A., on the Parnassus Mountain. The scope was to demonstrate, that the above soil improving materials are also appropriate for the recultivation of sites under extreme climatic and orographic conditions. The first results revealed, that where NOVIHUM® and hydrogel were combined, plant growth was greater than the average. The one-year results of the experiments fulfil our expectations concerning the application of NOVIHUM® in combination with hydrogel for the afforestation of problematic sites, such as the south-exposed steep slopes of the spoil piles of uranium mining. They may represent the most detrimental sites for afforestation in Europe.

Jan 1, 2002

Direct force measurements were conducted using an atomic force microscope (AFM) to study the mechanism of copper-activation of sphalerite. The force measurements were conducted between a sphalerite plate and a hydrophobic glass sphere in xanthate solutions of various pHs. The glass sphere may represent the hydrophobic air bubbles interacting with minerals during flotation. The force measurements conducted with unactivated sphalerite in 10') M KEX solutions did not show the presence of hydrophobic force. On the other hand, the results obtained with copper-activated sphalerite at pH 9.2 and 4.6 showed strong hydrophobic forces. However, the results obtained at pH 6.8 showed no evidence of hydrophobic force, which provides an explanation for the difficulty in floating sphalerite at neutral pH.

Jan 1, 1998

By Elvin R. Beach, Jaroslaw Drelich

Pull-off forces were measured for 8-9 pm diameter polystyrene (PSI particles on smooth spin- coated polystyrene films and hexadecanethiol (HDT) self-assemble monolayer surfaces using atomic force microscopy (AFM). Three parameters were controlled during experimentation: (i) the maximum applied load pressing the particle onto the substrate was varied from 50 to 4,000 nN, (ii) loading/unloading rate for the particle to attach and separate from the substrate varied from 0.01 to 9.3 Hz, and (iii) contact time for particle to reside on the substrate surface before retracting the particle to separate it from the surface changed from I µsecond to 200 seconds. the pull-off forces increased with increasing applied loading, increasing loading/unloading rate, and increasing contact time for the PS particle on PS film and on HDT monolayer. The PS particles experience elastic and plastic deformations duringpull-08 force measurements. Plastic deformation is primarily associated with flattening of surface irregularities. The results obtained in this research suggest that the particle-substrate contact areas of the magnitude comparable to those predicted by the JKR contact mechanical model can be reached in the AFM experiments by using high applied loads and long particle-substrate contact times. This result re-opens the prospect of' using AFM for studying surface energies of deformable micro-particles, even if the micro-particles have small irregularities on the surface.

Jan 1, 2003

By G. Récoché

For the African continent promoting a sustainable utilization of its mineral resources could be considered as a key determinant to fight against poverty. Sustainable development performance indicators for measuring the economic, environmental and social impacts of mining activity are necessary for drawing up policies and sectoral actions, identifying and controlling risks, identifying and implementing sustainable development actions, negotiating between stake-holders, improving mine production, etc. To respond to this need, the SIGAfrique Network proposed to develop a joint decision support tool entitled the African Mining Observatory (AMO) and, to this end, develops a system of indicators to be integrated within the SIGAfrique database. The development of both the OMA and the indicators is based on a participatory method within the working groups, which comprise experts/participants from the 13 SIGAfrique partner and observer countries (Guinea, Burkina Faso, Mali, Tanzania, Niger, Mozambique, Kenya, Uganda, Senegal, Angola, Madagascar, Ethiopia, and Mauritania).

Jan 1, 2007

By Steve Kral

The Society for Mining, Metallurgy and Exploration’s origins can be traced back to 1871. This was when 22 Pennsylvania coal mining engineers founded the American Institute of Mining Engineers (AIME). The organization’s objective was to “promote the arts and sciences connected with economic production of the useful minerals and metals, and the welfare of those employed in those industries by all lawful means.” Metallurgy and Petroleum were added to the AIME name in 1919 and 1956, respectively. Divisions of AIME were formed throughout the following years in recognition of the increasing trend toward specialization among mineral industry engineers. At the time, SME’s divisions consisted of the Coal Division (1930, now known as the Coal and Energy Division), the Industrial Minerals Division (1935), the Mineral and Metallurgical Processing Division (1948) and the Mining and Exploration Division (1949). The Environmental Division was created in 1997.

Jan 1, 2007

By T. Resende, J. Sismour

"Signs in underground mines are subject to variable airflow, which carries dust and moisture. Dust buildup reduces their visibility, hampering production efficiency and safety. Underground workers commonly must stop to clean signs in order to gauge their location, or find critical supplies or services. There are currently a variety of coating products, including dust and water repellants, available on the market that have the potential to reduce dust accumulation on sign surfaces. This paper describes a preliminary study to determine their effectiveness. The study involved a practical testing protocol using a trickle rock duster and samples cut from a clean, used road sign. Product effectiveness, under both dry and wet conditions, was evaluated based on photographic evidence by comparing changes in sign luminosity after a period of rock dust application. By analyzing the frequency of different pixel luminosities on the dust-covered samples, both uniformity of dust coverage and the total amount of accumulation was assessed. Results indicate that at least one product may reduce the amount of dust buildup on sign surfaces and increase visibility. INTRODUCTION In all underground mines, visibility of signage is critical. Signs inform miners of their location, direction toward escape routes, and location of supplies. Over time, sign surfaces can collect dust and can eventually become unreadable. The rate of dust accumulation on surfaces is often particularly high in coal mines, where both mining (e.g., cutting and drilling) and rock dusting activities can contribute significant amounts of dust to the airways. Several factors may contribute to dust buildup on sign surfaces. First, basic principles of fluid and particle flow are at play. When a fluid travels past a stationary surface, the velocity of the fluid at the surface boundary is zero. If a very small dust particle moving with air collides with a surface, it does not immediately fall off since the air velocity is zero at the sign surface. (This is the same reason that dust can collect on a rotating ceiling fan.) Further, once the collision occurs, other mechanisms may help keep the particle there – including friction that resists particle falling due to gravity, and adhesive forces due to humidity and/or static charges the particle and others already on the surface. Currently, the most common way to deal with reduced sign visibility due to dust buildup is for mine personnel (e.g., a compliance foreman, supply worker) to periodically clean sign surfaces – usually just by wiping them with a cloth. As a regular activity, this solution is inefficient; in cases of emergencies, it can also pose unnecessary risks. Application of an off-the-shelf coating to sign surfaces may represent a simple yet effective way to reduce the rate of dust accumulation. There are currently a variety of products on the market that may be suitable for this purpose, including dust and water repellants."

Jan 1, 2017

By Oscar Auerbach, Marvin Kuschner, Rosemarie Mick, Geno Saccomanno, Stephen Wood, Victor E. Archer, Marlene Egger

INTRODUCTION Excess bronchogenic carcinoma has been demonstrated among underground uranium miners in the United States, Czechoslovakia, and Canada (Archer 1981). This excess cancer is attributed largely to radiation from the alpha particles delivered to the tracheobronchial epithelium by the decay of short-lived daughters of radon. Interaction between the radiation and cigarette smoking has been demonstrated in production of the excess cancer (Archer 1973). The distribution of histologic types of bronchogenic cancer among uranium miners was established as different from that in other men in 1964 when an analysis of the first 51 cases among United States uranium miners was published (Saccomanno 1964). It was confirmed five years later by Yugoslavian studies (Horacek 1969). A later analysis, using a relative frequency method, indicated that oat cell and other small cell undifferentiated carcinomas increased markedly with increasing exposure to radiation in uranium mines (Saccomanno 1971). A subsequent analysis used only cases from an epidemiological study so as to enable calculation of expected numbers. It showed that there was an elevation in incidence of epidermoid, adenocarcinomas, and possibly other types, as well as small cell undifferentiated carcinomas (Archer 1974). At that time, it was felt that the histological distribution of cancer among uranium miners was well established. However, one of the authors (GS) has noted that fewer oat cell carcinomas were appearing among uranium miners in recent years. In his material the fraction of oat cell carcinoma, in successive 5 year periods between 1960 and 1980 was 59, 46, 37, and 22 percent. The association with calendar years is almost certainly spurious, reflecting some other factor associated with time. From the standpoint of tumor biology such a change must be important. This is a preliminary report which attempts to determine the cause of that change. POSSIBLE REASONS FOR OBSERVED CHANGE IN CELL TYPES 1) It might reflect a decrease in radiationinduced carcinomas, so that most of the ones being seen now are cigarette-induced. This appears to be a possibility because radiation levels in mines had been markedly reduced in the early 1970s, and because most of the uranium miners now developing carcinoma had quit mining during the 1965-1975 period. 2) It might represent a change in interpretation by the pathologists involved. 3) It might represent a real change in distribution as a result of increased latency, an aging population, cessation of smoking, increasing pack years of cigarettes, or other factors which have changed with time. Each of these possibilities is being checked. Dr. Waxweiler, later in this conference, is presenting an updated mortality analysis of United States underground uranium miners. His data indicate that lung cancer incidence among the Study Group of uranium miners is still quite high, but the ratio of observed to expected is falling somewhat. It is apparent that decreasing exposures in uranium mines is not yet reflected in normal lung cancer mortality rates. Reason #1 is therefore very unlikely. Thirty-five percent of the histologic types of carcinomas in this study were classified by a panel of three pathologists, 45% were classified by one of the panel members, and 20% were classified by a number of

Jan 1, 1981