Search Documents

By B. E. Davis

A problem that has continued to plague the Florida phosphate industry is the loss of coarse phosphate in the flotation circuit. Attempts to remedy this problem such as floating the coarse material (plus 425 µ m) in a separate circuit have resulted in limited success, but recovery is still not optimum. The Bureau of Mines is investigating ways to improve the recovery of coarse phosphate through improvements in the conditioning step. Studies to optimize conditioning parameters such as agitation energy, conditioning time, conditioner solids, and residual clay content have resulted in improved P2O5 recovery. Optimizing these and other conditioning parameters resulted in a rougher concentrate grading 30 pct P2O5 with a P2O5 recovery of 97 pct.

Jan 1, 1993

By Steven I. Olson

Since the introduction of froth flotation, the Florida Phosphate Industry has faced the challenge of coarse particle -850 +425µm (-20 +35 Tyler mesh) beneficiation. Several techniques have been used to upgrade this difficult size range. This paper discusses one approach that has met with success; namely, improved fractional recoveries through enhanced areation and improved material transport characteristics via larger than standard flotation cell mechanisms.

Jan 1, 1981

? The economic health and national security of the U.S. depends on the continued availability of, and access to, reliable and affordable energy and mineral resources. However, America is hindered by a costly, inefficient and often redundant regulatory structure that thwarts domestic investment, expansion and job creation. The annual cost of federal regulations in the U.S. increased to more than $1.75 trillion in 2008; averaging $8000 per employee.(The Impact of Regulatory Costs on Small Finns, SBA, 2010) ? The complexity, uncertainty and delays within the current permitting system places the U.S. at a competitive disadvantage with many other countries that have both abundant mineral resources and a more welcoming business and regulatory climate. As a result, American and international mining companies often move overseas or across borders to invest capital, create local employment, and produce the critical minerals America must then import at higher cost, while sacrificing employment and economic stimulus. ? According to Behre Dolbear, the U.S. is ranked lowest globally due to the lengthy permitting period required before mine development can commence. (Where not to Invest, 2010).

Jan 1, 2011

By III Boxley

Most of us realize that our nation's roadways are under ever-increasing stresses, from higher traffic counts to increased tire pressures and their resulting loads. At a time when the interstate system as originally envisioned is completed, and the National Highway System is being drawn to replace it, it is appropriate that we examine design and construction methods for the next century. The stone industry shares a common desire to produce high quality, cost-effective roadways that perform over time. The superior sub-grade and road base structure provides for the superior roadway. Since I am neither an engineer nor a contractor, I will not attempt to suggest design or construction methods. What I can do is share my company's experience in supplying road base materials by using a historical perspective in Virginia and some trends in the market that we have observed. Road building and related non-building construction are still far and away our largest markets as an industry. If we can help to improve the end product of our biggest customers, we add value to our own product. Indeed, in a time of budget constraints and competing demands for government dollars, we must show value over the life of a pavement structure to ensure their long-term funding.

Jan 1, 1996

By Bill Kendall

"In coal mines, handheld air, electric and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in longwall recovering bolting. In hard rock mines, pneumatically powered jackleg drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand- held hammer drills due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines.Although the handheld equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib and face; tripping hazards; bending twisting lifting hazards; high noise levels and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator - continual jackleg operation frequently results in longterm damage to hearing, shoulders, arms and wrist joints and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company.Hand-held drills also typically have limited thrust and torque capability that limits their ability to push long resin bolts, inadequate torque to properly install resin bolts or to properly torque mechanical or tensioned rebar bolts. Hand-held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or "riding the drill" is limited to 2.44 m (8 ft)."

Jan 1, 2014

By B. Kendall

"ISSUES ASSOCIATED WITH HAND DRILLING/JACKLEGS In coal mines, hand held air, electric, and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in long wall recovering bolting. In hard rock mines pneumatically powered “jack leg” drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand held hammer due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines. Although the hand-held equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib, and face; tripping hazards; bending twisting lifting hazards; high noise levels; and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator – continual jackleg operation frequently results in long term damage to hearing, shoulders, arm and wrist joints, and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company. Hand held drills also typically have limited thrust and torque capability which limits their ability to push long resin bolts, inadequate torque to properly install resin bolts, or to properly torque mechanical or tensioned rebar bolts. Hand held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or “riding the drill” is limited to 8’ (2.44M)."

Jan 1, 2015

By S. Gallagher, A. Mayton, R. Merkel

The prolonged exposure of equipment operators to shock and whole-body vibration (WBV) is linked to cumulative back, neck and abdominal disorders. In low coal mines, space restrictions make it difficult for seat suspensions to isolate operators from shock and WBV. Researchers at NIOSH's Pittsburgh Research Laboratory are responding to these issues by investigating viscoelastic foams. For the full-load case, an ergonomic seat made with viscoelastic foams can isolate the shuttle-car operator from shock at 15 Hz. Researchers used results from additional foam testing using an analytical model to identify viscoelastic foams that provide shock isolation at a frequency below 5 Hz.

Jan 1, 2000

By Y. Wang, E. Forssberg, A. Johansson, B. Chan

A super-conducting high gradient magnetic separator with matrix vibration in dry separation mode is a powder purification device, which has been used to remove weakly magnetic impure particles from fine calcite powders below 53 µm in this study. A fundamental question concerned is the evolution of the matrix clogging under gas-solids loads. This paper presents the improvement of the separation selectivity using a method of mechanically based vibration on the matrix in the separator. The functions of the matrix vibration are discussed. The results indicated that the mechanically based vibration on the matrix within a high intensity magnetic field while a feed was introduced in an air stream, was found to be effective for the dry purification of fine powder materials.

Jan 1, 2001

By William H. Pomroy

This report describes research leading to the design, prototype fabrication, and successful in-mine proof-of-concept testing of two improved stench fire warning systems for underground noncoal mines. The stench system, widely used in underground noncoal mines to warn of fire or other emergency suffers several serious shortcomings, including the toxicity of the odorant leading to debility in miners; reactivity of the odorant with iron oxide, resulting in unreliable warning because the odor may fade when transported long distances in steel pipe; lack of control over the rate at which agent is released into the air-stream, resulting in some work areas receiving unbearably high stench concentrations and other areas being missed altogether; lack of visual indication of system status, valve positions, or proper system operation; and excessively long stench transit times. In 1979, the Bureau of Mines, U.S. Department of the Interior, began research to upgrade the stench warning system. Two systems were subsequently developed which offer significant advantages over current systems.

Jan 1, 1984

By Priscilla P. Nelson, Yousof Abd Al-Jalil, Christopher Laughton

Prediction of excavation rates is a critical element in the pre-planning of a tunnel boring machine (TBM) project. A realistic evaluation of performance expectations is needed that reflects both the knowns and unknowns of the excavation process and geologic conditions. Current planning procedures are often based on deterministic “best guess” estimations. In this paper, a probabilistic approach to performance simulation is presented that will permit rational consideration of general and project-specific uncertainties in establishing realistic performance estimates. Companion to the simulation software is a database of over 600 public-domain case histories.

Jan 1, 1999

By Christopher E. Johansson, William J. Kohr, John W. Shield

Heap biooxidation is an economical means to treat refractory sulfidic ores. However, air flow limitations are a major obstacle in commercialization of this technology. Geobiotics, Inc. has developed a new process for heap biooxidation of sulfide ores that renders the ore more susceptible to bacterial oxidation. In this process, air and liquid flows in the heap are greatly improved by first removing clays and other fine particles from the ore. Gold bearing sulfides are recovered from the removed fines and separately biooxidized. Column biooxidations were conducted on two refractory sulfidic ores from which the fines had been removed in order to improve air flow through the column. Gold recoveries increased from 46% to 90% for a mill grade ore and from 52% to 80% for a low grade ore after biooxidation. Fines and clays in these ores had precluded whole ore heap biooxidation from occurring. This new process addresses the most significant problem of large scale heap biooxidation.

Jan 1, 1996

By O. A. Bascur

Based on current sedimentation theory an on-line thickener model was developed and coupled with an extended Kalman Filter to obtain additional information such as the compression zone level and concentration, a corrected underflow concentration, the inventory, and some rheological information. The on-line model was installed and tested for robustness for periods up to three days in an industrial environment giving good results. Emphasis was given to signal processing and selecting the appropriate input variables for filtering. The analysis of the thickener from a phenomenlogical point of view provides for better operation, establishes the limiting operating conditions, and assists in the design of control strategies.

Jan 1, 1986

By Steve Kral

U.S. mines are among the most efficient, productive and safest in the world. Much of that efficiency is due to the high-technology equipment and processes available to the industry. The U.S. mining industry can produce more material now with fewer people than it could a few decades ago. And that material can be produced more safely. However, the workforce is growing older and fewer young people are filling the holes created by retirements. Even though mining is one of the highest paid occupations in the United States, young people believe they can find jobs that pay almost as well without the risks and the often remote locations associated with mines.

Jan 1, 2002

By Bruno A. Fichna

Longwall mining offers low cost potential for coal with high capital investment. As opposed to two shifts-per-day operation in most long- walls, Saarberg Mines in Germany increase utilization of capital by operating their longwalls around the clock. Differentiation between capital and operating costs, corrective maintenance versus preventive maintenance, improved roof conditions, and economical life of equipment was investigated. A surprisingly high degree of improvement was attained. Capital costs at Saarberg longwall coal mines have been reduced through a step-by-step research and trial program. This reduction was particularly influenced by the high performance pilot longwalls at the Ensdorf mine. The following presentation shows data and figures of those longwalls. End results were 40% reduction in capital costs, which could contribute favorably to investment decisions in the coal industry in a supply side economics environment.

Jan 1, 1982

By Robert A. Jankowski, J. Drew Potts

The Bureau has identified several ventilation techniques and a water spray application for reducing auger mining dust levels. The dust control methods all work by improving air quantity or flow patterns at the face. Section airflow is maximized by reducing air leakage between entries. Sealing stoppings with brushed- on mortar, containing fiberglass additives, reduces leakage. Heading airflow is maximized by properly installing the brattice curtain and keeping the area between the curtain and rib free from obstructions. The brattice curtains should be hung at least 1.7 m (5.5 ft) from the ribs in 7.9 m (26 ft) wide entries and kept less than 4.6 m (15 ft) from the face. A tight curtain seal is created by using the mine air pressure to force the curtain against the timbers, roof and floor of the mine. Using both a blowing curtain and an exhausting curtain will isolate some face workers from dusty air. The Bureau designed, auger clearer spray system, can be used to force heading air across the active face. Laboratory tests indicate that the auger clearer spray system can increase face velocities by more than 0.5 m/sec (100 ft/min), while using less than 0.13 l/sec (2.0 gal/min) of water.

Jan 1, 1989

By Jerry R. Riding

Metallurgical process methods have seen dramatic improvement over the past fifty years. As these improvements have come about, more and more emphasis has been placed on obtaining accurate and rapid analysis of the metallurgical processes. Well-defined conventional laboratory analysis procedures which have proven to be reliable were developed early in the mineral industry's history; however, these conventional procedures, which have not changed appreciably in fifty years, have the serious drawback that they are too slow to be of appreciable value in automatic control of the processes. For example, the assay results normally become available to a mill operator from eight to twenty-four hours after a sample is taken. Since the desired mineral separation can only be made while the minerals are in the flotation circuit, conventional assay results provide information similar to postmortem reports. Consequently, using conventional procedures, the mill is operated with information from an earlier period of time, which may not reflect current conditions. In recent years there has been a steady increase in the volume of required samples. At the same time, labor, material, and overhead costs have continued to rise causing the cost per assay to reach an alarming level. This rising cost per assay, plus the increasing demand for rapid analysis necessary for control, has caused the mining and metal processing industries to look toward other techniques to solve these problems As a result, X-ray fluorescence which can provide on-stream analysis necessary for control, as well as perform numerous laboratory assays at lower cost and at a much greater speed than conventional methods, has gained wide-spread attention. In addition, multichannel X-ray fluorescent instruments are now available which have been perfected to the point where the analysis of the most important chemical constituents is available within one minute after a sample is presented to the X-ray analyzer. Because of these obvious advantages, extensive use is being made today of X-ray analysis in the mining industry to analyze slags, ores, and mineral content of rocks. The results are used to make quick decisions for both mining and beneficiation of metals. For example, X-ray systems which provide rapid on-stream analysis of the slurries at desired points Fn metallurgical processes have recently been developed. The successful application of these systems has moved the milling process a step closer to fully automatic control.

Jan 1, 1969

By W. C. Foshee

The large volume of water used in coal preparation plants makes water recycling a necessity. Economical cleaning of dirty water usually requires flocculation with an efficient organic polyelectrolyte. This paper discusses identification of optimum flocculant systems. Supporting laboratory data with on-site tests and full scale field trials supplies information necessary for matching the polymer to the plant.

Jan 1, 1979

By Rameshwar Sah, Somasekhar Pitchika, Akhil Singh, Seenivasan Rajiah, C. B. Dayanand, G. Balachandran

In the sintering of iron ores, the partial substitution of anthracite coal for coke breeze has been considered to be an effective way of reducing emissions and improvement in sintering properties. In the present study, the combustion characteristics of the anthracite coal and coke breeze were investigated and its influence on product sinter quality and sinter flue gases is being monitored. Pot trials are carried out with different coke breeze ratios, 0%, 40%, 50%, 60%, and 100%. It is found that as the percentage of anthracite coal is increased from 0 to 100%, the sintering time decreased from 24 to 20 min, and the productivity increased from 2.25 to 2.60 t/h/m2. Up to 60% anthracite coal substitution Tumbler index (+ 6.3 mm%), Product yield (+ 5 mm%), and fines generation (− 5 mm%) is found 62.29%, 85.17%, and 15.33%; moreover, hematite ( Fe2O3), magnetite ( Fe3O4), calcium ferrite phases ( CaFe2O4, CaFe3O5), and Silico ferrite of calcium and aluminum (SFCA) are major mineral phases found during microstructural analysis of product sinter. Keywords Sintering · Anthracite coal · Combustion rate · Productivity

Jun 2, 2022

By R. Sripriya, Ch. V. G. K. Murty, N. D. Rao, P. V. T. Rao, A. Ramu

Studies were carried out to improve the performance of hydrocyclones at Tata Steel's chrome ore beneficiation plant in Sukinda, India. The optimal cut point of the hydrocyclones was determined in the laboratory using a stub cyclone. In the tests, the operating and design variables, including spigot diameter, density of feed slurry and inlet pressure, were varied. Subsequently, plant trials were carried out, and attempts were made to develop a model of the hydrocyclone using the Rao, Lynch and Plitt model. The cyclone efficiency was represented by the parti¬tion curve, and the performance was evaluated mathematically from a reduced efficiency curve, represented by the equation:

Jan 1, 2000

By A. Ferreira Morgado, P. de Souza Santos

The sodium smectitic clays (bentonites), have more industrial applications in that class of mineral, a driving force to obtain this mineral. In Brazil, there are several occurrences of smectitic clays, unfortunately they are polycationic, with a distribution of several exchangeable cations, where the cation sodium occurs in minor quantity. In this work, the original polycationic smectitic clay was firstly proper characterized and then treated with sodium carbonate obtaining homoionic sodium smectitic clay. The rheological tests in the optimized sodium smectitic clay showed good results for drilling fluids, typical of a sodium bentonite ones.

Jan 1, 1999