Search Documents

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

Jan 1, 2006

By Siegmund Babendererde, Jan O. Babendererde

Extruded Concrete Lining combines technological and financial advantages. The tunnel lining is reliably embedded in the surrounding ground as the fluid concrete is extruded at constant pressure directly behind the TBM supporting the exposed surface. Ground deformation from the TBM passage can be compensated and the ground will be pre-stressed by the extrusion process. Developments in concrete technology permit high speed tunneling by use of a slip formwork attached to the TBM. Realised projects in Milano (Italy), Lyon (France), Frankfurt (Germany) and Akima (Japan) will be demonstrated.

Jan 1, 2001

By G. E. Wasson

Consolidation Coal Co. tested the agglomeration of fine coal using a laboratory pellet mill. The principal operating variables examined were feed coal moisture, coal size distribution, and additives to the feed coal. The moisture of the feed coal was found to be critical to both the pellet mill operability and the product strength. Coals, with feed moistures too high to pelletize, could be pelletized if mixed with lime or a water absorbent material. The addition of dry starch binder improved the product strength.

Jan 1, 1991

By Wilson I. L. Lim, Jonathan J. Campbell, Luis A. Tondo

An important issue in the use of high pressure grinding rolls when grinding ores is wear of the rolls. Due to the abrasive nature of the ores, significant wear rates have typically occurred. Attempts to address the wear problem require a better understanding of the wear mechanisms. A probable wear mechanism is the abrasion of the rolls surface due to extrusion of the compacted material as it leaves the rolls. This paper presents the results of a study on a number of ores to examine the extent of extrusion that occurs. The study involved laboratory, pilot and full-scale high pressure grinding rolls. The effect of variations in parameters such as grinding pressure, rolls speed, initial gap settings, feed topsize and moisture was investigated. The results indicate that extrusion increases with increasing grinding pressure and rolls diameter, while the use of studded or profiled rolls significantly reduces the extrusion effect compared to smooth rolls. It was also found that rolls speed and feed moisture can have significant effect on extrusion, depending on the material.

Jan 1, 1998

By D. M. Range

Exxon is reclaiming an 80-hm2 (200¬acre) Wyoming uranium tailings basin in accordance with US Nuclear Regula¬tory Commission (NRC) requirements. The reclamation plan is designed to control the tailings and their radioactive emissions for at least 1000 years. Rigorous modeling and analyses of potential erosion by wind and water were used in planning. The use of riprap was minimized and the need for long¬term reclamation maintenance was eliminated. The resulting design is simi¬lar to regions stable from erosion cre¬ated by nature. The concepts used in the design and implementation have wider reclamation application. Highland history Exxon operated the Highland uranium operations from 1972 until mid-1984. Open pit and underground operations mined the roll front, sandstone ore body. The 2.5 kt/d (3000 stpd) mill employed conventional crushing, grinding, sulfu¬ric acid leach, CCD, SX, precipitation, and drying circuits. The mill produced 10 Mt (11 million st) of tailings. An¬other operator began commercial scale in situ leach operations in 1988. The tailings basin was constructed by deposition of mill tailings in a natural ravine dammed with a 30-m (100-ft) high by 1050-m (3400-ft) long clay core earthen dam built entirely downstream of tailings. Figure 1 shows the layout of the tail¬ings basin in 1984. Tailings were de¬posited along the dam face on the east side of the basin as well as in the west end and along the south edge until the early 1980s. This left a deep water pond in the middle of the basin. The deep pond was largely filled with tailings during the last four years of mill opera¬tions by the construction of two tailings causeways and the operation of a float¬ing tailings line. The pond water volume was mini¬mized by recycling tailings water to the mill and by operating a 32-L/s (500¬gpm) evaporation enhancement spray system during the last few years of mill operations. Regulatory requirements Several conceptual tailings basin rec¬lamation plans were prepared during the mine life. In September 1984, Exxon began preparation of a detailed plan in response to an NRC request. Water, Waste and Land Inc. (WWL) of Fort Collins, CO was selected to help pre¬pare the plan that was submitted to the NRC in December 1984. The design had to meet the require¬ments found in NRC regulations (NRC, 1985). These were based on regulations prepared by the Environmental Protec¬tion Agency (EPA, 1983) at the man¬date of federal law (UMTRA, 1978). The NRC regulations contain strict primary standards and a somewhat more flexible set of secondary standards. The primary standards include requiring that: • radiation from tailings be reduced to background levels; • radon gas emitted by the tailings be reduced to 20 pCi/m2/s from the surface of the reclaimed tailings pile; • tailings not be dispersed into the environment; and • these conditions endure without routine maintenance for at least 200 years and for 1000 years to the extent reasonably attainable. The lengthy time requirements pre¬sented a large engineering challenge. Radon is a radioactive, chemically inert gas with a 3.8 day half-life. It is released from uranium tailings by the radioactive decay of radium, which, in turn, is a radioactive decay product of uranium. Radon emissions from ura¬nium tailings can be controlled with an earthen cover thick enough that the radon gas decays to its solid, short-lived radio¬active daughters before the radon dif¬fuses through the cover material into the air.

Jan 1, 1989

By F. P. Jung

This presentation will be a general overview of the Cerrejon Coal Project being developed jointly by Carbocol, an entity of the Colombian government, and Intercor, an Exxon affiliate. The word "Cerrajon", by the way, is simply Spanish for a small hill. There is a distinctive hill near the mine site, and it's the only landmark of any significance. It's shown in Figure 1. So the locals call this area "El Cerrejon", "the little hill." Let me start with some of the highlights of the project, summarized in Figure 2, and then go into more detail later. A four-year feasibility study covered the geology, quality, engineering, construction operation and marketing of coal from this region. This study led Exxon to declare the project as commercial in July of 1980. Then in September of 1980 the president of Colombia gave the government's okay to proceed.

Jan 1, 1982

By V. I. Kefeli

Public-private partnership efforts are working to create green landscapes from abandoned industrial sites. Fabricated soils, potentially an essential element of such landscapes, are designed to substitute for topsoil on the areas free from ground cover and plant community. The aluminosilicate matrix and humus form the soil micelle - the primary unit of any soil complex. Humus formation is a process based on carbon-nitrogen interaction. Sources of carbon can be materials rich in easily composted products like cellulose and polyphenols (plant leaves) or aged lignin polymers (saw dust from different woody plants). The pathways of carbon-nitrogen complexes are discussed. Properties of the fabricated soil components were examined by bio-tests and plant models.

Jan 1, 2002

By Madeline Mello, Michael Low, Nick Karlin, Bryce Scofield

The LA Effluent Outfall Tunnel is the first tunnel in the United States to incorporate post- tensioning into the precast segmental lining. Several unique components were integrated to ensure that the post tensioning could be carried out successfully in the tunnel, even concurrently with the TBM excavation. This also required the development of new processes both in the casting facility and in the TBM to ensure that the almost 3,700 rings could be successfully manufactured, threaded, stressed, and grouted. This paper will discuss the material selection, fabrication, and installation of, as well as lessons learned from, this first in country tunnel lining.

Jun 23, 2024

By J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 40 ft of advance because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation) as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By K. Kovári, G. Anagnostou

Slurry and EPB-shield tunnelling have been successfully applied worldwide in recent years. Under extremely unfavourable geological conditions, however, face instabilities may occur. The present paper aims at a better understanding of the mechanics of face failure. For the case of slurry shield, attention will be paid to the time-dependent effects associated with the infiltration of slurry into the ground ahead of the face. Related topics, such as the stand-up time and the effect of the excavation advance rate, will be discussed. In the case of an EPB-shield, a distinction will be drawn between fluid-pressure and effective pressure in the chamber. The effective pressure can be visualized as a “grain to grain” contact pressure between the muck and the ground at the face. The water pressure in the chamber reduces the hydraulic head gradient in the ground and, consequently, the seepage forces acting in front of the face. The face is thus stabilized both by the direct support of the pressurized muck and by the reduction of the seepage forces in the ground. The paper includes normalized diagrams which allow the assessment of tunnel face stability.

Jan 1, 1997

By Jerry C. Tien

This paper investigated the airflow pattern in the working face area during a cross-cut development. The study used a 10:l scale face model and a mock continuous miner. Results showed that keeping up the line curtain is essential in order to avoid recirculation and to control respirable dust and methane, in the face area.

Jan 1, 1989

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study was conducted at a western U.S. coal mine to evaluate the movement of longwall face air and exchanges between the face and worked-out areas to document the presence or absence of face airflow pathways between these locations. This field study was part of a project investigating the effect of longwall face length and caving characteristics on longwall face air behavior and its potential movement on and off of the face. Tracer gas experiments using sulfur hexafluoride (SF6) were done to describe air movement on the face and in the mined-portion of the active panel. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob.

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob.

By V. Kontogianni

The underground extraction of coal is associated with ground movements extending from the mining area to the ground surface, which result in bowls of ground subsidence, with amplitude exceeding the amount of several meters and occasionally with important tilt and curvature of ground surface. Such changes at both the underground environment and surface topography lead to destruction of buildings, failure of utilities and transportation networks, and occasionally formation of areas vulnerable to flooding, or even small pools. Based on geodetic surface measurements of ground elevation changes, various theories and empirical models relating surface subsidence with the geometry of underground voids formed have been proposed, and predictions of expected subsidence in the form of contours have been estimated. In this study a case study of planning of a new highway network through areas in which coal extraction was also planned is discussed. This work is partly funded by EU. The optimum solution selected was a modification of the initial highway planning, so that the road is increased in length and by-passes the richest coal-field, where maximum post-exploitation subsidence was predicted, and only crosses either minor coalfields, which are not to be exploited, or even margins of main coalfields, in which minor post-exploitation subsidence is expected.

Jan 1, 2006

By M. M. Ragin, B. J. Scheiner

The US Bureau of Mines (USBM) has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. It was found that at a given polymer concentration, there were an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By B. J. Scheiner

The Bureau of Mines, Department of Interior, has been investigating the use of polyethylene oxide (PEO) as a flocculant for a variety of mineral wastes. As part of this investigation, the hydrodynamics of the flocculation process were studied. It was determined that to obtain optimum dewatering results, the factors of energy input into the stirrer, polymer concentration, and polymer dosage must be considered. Lt was found that at a given polymer concentration, there was an optimum stirrer speed and polymer dosage. With excess PEO, the amount of water removed in the trommel decreased, but no evidence for steric stabilization was observed.

Jan 1, 1987

By R. F. Holub, P. J. Dallimore

Basic to solving the problem of the role of radon transport on radon concentrations in mines is to establish whether it occurs primarily as diffusion and forced flow through porous rock or through fissures in the rock. The laboratory experiments performed involved measurements of diffusion and emanation coefficients, porosity and permeability of representative rock samples. Significant differences have been found when comparing the results of the laboratory permeability determinations to those of the mine determinations. Considerations of underlying principles, however, suggest that the diffusion and emanation coefficients are the same in laboratory and mine. It was also found that moisture content plays a dominant role in radon transport through rock. Using these concepts and findings, some conclusions about the radon concentrations in mines have been drawn.

Jan 1, 1981

By Robert D. Schmidt

The Bureau of Mines is conducting an investigation to develop remediation techniques for residential water wells whose yield has been affected in the long term, by underground mining. Initial work relating to this project was conducted in 1984-1987 at a room and pillar mine in Indiana County, Pennsylvania. Piezometer nest data from the room and pillar mine reveals that a downward gradient in piezometric head exists in shallow strata as a result of drainage into the underlying mine void. The vertical gradient in head in turn results in well bore leakage in open-hole water wells. The relative yield of valley wells is only slightly affected however because the high surficial recharge rate through fractures more than compensates for fracture leakage into the underlying mine. The relative affect of well bore leakage on well yield is greater in certain hillside and hilltop wells that have comparatively low inflow rates at shallow depths. The static water level of such wells is determined to a much greater extent by the chance interception of deep outflow fractures, than is the case for wells drilled in a more intensively fractured valley bottom. The lower static water level of wells that intercept deep fractures does not necessarily reflect the water table conditions outside of a small radius around the affected well. The results suggest that permanently isolating well bore outflow fractures may remediate certain open-hole residential wells that have been affected by high extraction underground mining.

Jan 1, 1986