Search Documents

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By S. Srinivasan

Traditional pit optimization techniques cannot take account of the requirement to blend ore in order to produce a saleable product, as is the case for iron ore, coal, limestone and other industrial minerals. Various techniques are proposed to overcome the deficiencies, many of which have been tested. The techniques in general involve the combined application of pit optimization and blend optimization techniques.

Jan 1, 1996

By Norman Miskelly

Role of CRIRSCO CRIRSCO has an advisory and hopefully influential role in International Mineral Resource/Reserve Reporting Standards CRIRSCO also has a broad educational role CRIRSCO does NOT have a negotiating role CRIRSCO does NOT have a regulatory role

Jan 1, 2003

By H. J. van Antwerpen

AngloGold Ashanti operates the world`s deepest mine, Mponeng gold mine, in South Africa. A vast refrigeration and ventilation system provides acceptable working conditions 3800m below surface at 60°C rock temperature. In such a system, optimisation and assessment of modifications becomes very difficult. With that in mind, a research project was launched to determine whether recently developed system simulation technology can be applied to a mine as vast and complex as Mponeng. Using the techniques and methods as implemented in FLOWNEX software, it was indeed proven to be possible to do a mine-wide combined simulation of compressed air flow, ventilation air psychrometry and refrigeration water systems. Interactions between the various streams included heat transfer, pressure drop, evaporation and condensation. The simulation model was used in a parametric study to test various water flow and temperature operating points for the refrigeration system. It was found that, given current limitations, the mine refrigeration system is running fairly close to optimal but with some opportunities for improvement. The simulation model also provided useful insight for future changes or extensions to the system.

Feb 23, 2014

By Nural Kuyucak

Several thousand years ago, metallurgists discovered that by combining two relatively soft metals, copper and tin, they could make a new material, bronze, that was stronger than either metal separately. Bronze and other alloys show how different materials can be integrated to create something new and better. Today?s mining industry can likewise find benefit in an integrated approach to managing the external impacts it has through its waste materials and its use of water. Just as using bronze gave ancient nations an economic and military advantage, mining companies can gain competitive advantage through finding better ways to manage water and waste. Trends pushing this include: ? Environmental ? Regulations on water-taking and the quality of discharged water are becoming more stringent. Net zero discharge requirements are often imposed by regulators. Mining companies also come under pressure to manage environmental impacts of mine waste, including minimizing the area occupied by waste and seepage amount resulting from infiltration of water from a smaller surface area. ? Social ? Particularly in arid parts of the world, there are multiple possible uses for each gallon of water. Local residents do not want to see a reduction in supplies of water for agricultural, domestic, manufacturing and other purposes. They get suspicious about any potential impact of water being mixed with their water reservoirs if it comes from a mining site, even if it would be treated. Such suspicions may cause conflicts among the stake-holders and delays in project approval processes.

Jan 1, 2009

By K. E. Brown, T. D. Murphy

At Monterey Coal's No. 1 Mine in central Illinois, it became necessary to predict if the sulfur content of individual trainloads of coal would exceed a contract sulfur maximum. Using geostatistics and Monte Carlo-type simulations, a forecasting procedure was developed to meet this need. The developed procedure predicts the monthly, mean sulfur content of the coal shipped and the probability of individual shipments exceeding the contract limit. During the first five months of using this procedure, the forecasted, monthly mean sulfur value was within 0.03% of actual. This represents a significant improvement over the inverse-distance, gridding-based, forecasting used previously.

Jan 1, 1994

By Fred L. Stanley, Ricky Q. Honaker, Michael J. Mankosa

Spiral concentration has gained a great deal of popularity as a cheap, effective method for recovering fine coal (8x100 mesh). Typically, 6-turn, wide-profile spirals are used in either a single pass, open- circuit configuration or in combination with a middlings retreat circuit. Recent work conducted at Carpco, however, has indicated that a split feed scenario and/or hydraulic classification in advance of spiral concentration offers significant advantages in both capacity and metallurgical performance. In addition, it has also been shown that the apparent density separation which naturally occurs in a hydraulic classifier provides significant up-grading in terms of pyrite and ash rejection. The results from this study will be presented in comparison with those obtained from open-circuit spiral testing.

Jan 1, 1995

By M. ]. [Mohkam

The paper describes the features of the problems encountered and the countermeasures taken for two different tunneling projects. Where, slurry shields were used to excavate, in soft heterogeneaous water-bearing grounds, tunnels passing at very low cover beneath existing foundations of H.T. electric pylons, underground structures and major utilities. In order to avoid any ground failure and/or damage to the existing structures, one option was ground treatement by grouting or freezing technics. However, it was judged that, based on previous experiences, excavation with slurry shield could be carried on securely using an appropriate slurry enriched with polymers and applying a well determined pressure at ground face. A three dimensionnal limiting equilibrium analysis model was used to determine proper confinement pressures. And, the appropriate slurry compositions were stabilished based on laboratory test results. The tunnels were excavated successfully, no ground failure was experienced, and the maximum settlement recorded (on pylons) didn't exceed 3 mm.

Jan 1, 1991

By K. W. Harris, K. A. Perry

Underground coal mines beneath Black Mountain in the Harlan County district of the Central Appalachian coalfields have an extensive history of bump events, which yields an elevated probability for significant injury or fatality to underground miners. According to Mark (2009), Harlan County has had the greatest concentration of deep-cover retreat mining in the United States. Combined with the extensive multiple seam mining history, room-and-pillar coal bumps have had a disproportionate impact on coal operations in this region. The Harlan seam, one of the principal, economically recoverable coalbeds exploited beneath Black Mountain, has a significant burst history that extends into modern times. A numerical investigation using the LaModel software of 17 bumps that occurred at the same mine in the Harlan seam was conducted and used to create a calibration methodology which serves as the quantitative basis for current and future numerical efforts in an adjacent mine exploiting the same reserve. In addition to this numerical study, a qualitative assessment of the geologic factors that are believed to contribute to the bump potential was completed. Combined with stability prediction using the numerical basis, these geologic factors will be used for recognition of high bump potential areas with the goal of reducing the potential for future bumps, helping to ensure the highest level of safety and productivity for underground personnel.

Jan 1, 2016

By J. Patrick Powers, Joel Miller, Arthur B. Corwin

A combination of a slurry trench with dewatering successfully controlled groundwater for a large sloped excavation immediately adjacent to the Arkansas River. The Murray Hydro Electric Project required excavation through sand and gravel to bedrock, 85 feet below high water in the River. The perimeter system of deep wells pumping up to 25,000 GPM (1,600 1/sec) lowered the water level to 15 feet (4.6 m) above bedrock. A short soil/bentonite slurry trench near the toe of the slope cut off the residual head. The method cut six weeks from the critical path. Design of the slopes and the dewatering system demanded high safety factors because of risk to existing Lock and Dam No. 7. A localized pocket of soft organic clay was supported by a rock filled bolster. A major flood event was successfully withstood. The method can be applied to large civil excavations and open pit mines.

Jan 1, 1989

By S. Bhattacharaya, S. Aich, B. K. Nandi

"At present scenario, there has been an increasing demand in the usage of blend coal in power sector; regardless of how, specific knowledge on burning and ignition characteristics and their interactive effects is stingy. In this work a detailed investigation was therefore taken up to study in detail the combustion characteristics of selected coal samples and their blends. Certain parameters were believed to have significant effects on combustion characteristics of individual coal and their blend. Major parameters identified for this purpose included proximate analysis, combustion conditions, heating rate, reaction regions, blending ratios, ignition condition, reactivity (or reaction rate) and burnout temperatures. With the help of these parameters, thermal features and reaction kinetics of the individual and blended samples were investigated through a qualitative and quantitative thermo-gravimetric analysis of two different individual coals and their blend carried out in an oxygen atmosphere from ambient to 800 0C at a constant heating rate of 10 K/min. A significant difference in terms of rate of mass loss with temperature correlated from Arrhenius expression along with coal-coal blend interactions and deviation from their expected behaviour, have been observed between the kinetics of individual and blend samples, the latter showing better ignition performance and comprehensive combustion phase. It was also found that particles having the lowest percentages of volatile matter and ash could possibly be blended with particles having high ash and volatile matter to meet the required burning condition which can be effective in terms of cost savings, improved fuel economy, reduced undesirable exhaust emissions and improved safety of coal burning equipment. Experimental results further indicated that individual samples and coal blend samples have different combustion features in terms of residue left, peak temperatures and activation energies. Thermodynamic activation parameters such as activation energy, pre-exponential factor and order of reaction were computed from the thermal data using the modified form of non-isothermal methods. INTRODUCTION Coal has been the most significant source of energy for India and would remain so at least for the next few decades. About 60-65% of the electricity produced in India is from coal fired power plants. Indian coal is of drift origin and of high ash content. Ash content of the coal burnt in power plants in India is in the range of 30-45%, most of it being Run-of-Mine coal. Most of the power plants in India source their coal from number of mines, most common being multiple sourcing. Usually coal from each source [1] is burnt separately. For various reasons mostly associated with logistics, burning of blended coal is rarely practiced. Blending of coal is practised mainly for improving the quality of available coal and meets the shortage of coal supply. Blending technique is generally practised in power industries to reduce the cost of power generation along with mitigating combustion performance or slagging problem ensuring consistency in as fired coal quality and also for environmental compliance. Blending good quality imported coal can improve coal quality and helps in preserving indigenous coal resources for longer period [2]. Use of blended coal shall reduce load on all boiler components (Mill, CHP, Boiler, AHP) & reduce O&M cost and increase the availability. The main purpose of blending is to get a blended as fired coal having ash, volatile matter and gross calorific value close to design coal and the two coals are to be blended in such ratio proportions that resultant coal blend have desired ash, volatile matter and gross calorific value [3]. For a coal to be blended certain parameters have to be considered to get compatibility with respect to combustibility ( Burn ability) of coal, grindability ( HGI), ash fusion behavior, swelling characteristics of coal, need to be checked"

Jan 1, 2017

By Felicia F. Peng

A laboratory fixed bed reactor was used in a study of generating clean thermal energy from coal fine refuse-limestone agglomerates. The major operation variables, including Ca/S mole ratio, agglomerate size, air flow rate and temperature, which affect the rate of sulfur fixation and combustible material utilization, have been examined. The test results show that 70 percent or more of sulfur fixation and 100% of combustible material utilization can be achieved depending upon sorbent, agglomeration, and combustion conditions. The coal fine refuse limestone pellet combustion process (CLC process) requires a simple flowsheet to convert coal fine refuse as a clean solid fuel, while meeting the strict air quality standards for SO2 emissions into the atmosphere. The CLC process is an attractive method to clean up coal slurry impoundments to protect our environment.

Jan 1, 1984

By N. H. Coates

The Bureau of Mines designed, constructed, and operated an 18-inch- diameter, fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8 percent. Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coefficients from the bed (-20 + 50 mesh mullite) to a water-cooled tube were about 75 Btu/hr-ft2- °F.

Jan 1, 1970

By A. W. Scaroni, C. Y. Tsai

The effect of particle size and composition on the pyrolysis and combustion of a pulverized bituminous coal in an entrained-flow reactor has been investigated. Predicted time-temperature histories of the coal particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm (about 140 mesh). This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate before ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of an HVA bituminous coal that were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite-rich samples.

Jan 1, 1987

By W. J. D. Stone

In 1960, Magnetics International Ltd. undertook the development of the Jones High Intensity Wet Magnetic Separator in the Americas. Magnetics International had a number of possible applications in its own projects plus the intention of developing the equipment for sale to others. It was soon recognized that no matter how innovative a piece of mineral separation equipment may be, it takes many years and much finance before it is finally accepted for large scale use. For this reason, many good ideas die in their infancy. One of the chief reasons for such a time lag between conception and large scale implementation is the usual lack of finance to construct and put into operation a large demonstration unit. Even with a large unit for demonstration, the first major user usually requires a guarantee that is not normal in accepted separation equipment. Such problems are also normally accompanied by major design changes from the first conception.

Jan 1, 1971

By Kenneth F. Lane

In most industries it is normal commercial policy to try to gear production to the market. In times of scarcity output is pushed to its maximum and in times of glut output is reduced. Because of the effects of supply and demand, these times correspond to times of high and low prices respectively so the policy results in maximising long run total profits. Stockpiling is often an integral part of the policy. Stocks are accumulated during depressed market conditions and sold off when demand revives. This further increases the long run total profits. However, such policies cause violent fluctuations in short term profitability and impose severe financial strains. Indeed planning and implementing the policies are a central management concern which is often critical to the success of the industry. The mining industry is no exception and, for many raw materials, trying to balance supply with demand is an international problem. Stockpiling and restricted production agreements are common elements of policy. But very little attention has been paid to the one additional control which is unique to the mining industry, namely, the cut off grade. This neglect is apparent at all levels from individual mines to national economies.

Jan 1, 1979

By Robert J. Storms, David J. Malone, Thomas E. Crandall

Corrosion and abrasion have been present in hydrometallurgical processes for many years. Ceramic lining materials have been used in several applications to protect process vessels from the corrosive and abrasive effects of a wide range of ore slurry processes. This paper reviews the history of ceramic lining systems utilized in hydrometallurgical vessels, the commercial benefits associated with their use, and additional areas of opportunity for the Mining Industry.

Jan 1, 1995

By K. Tempel

In December of 1999, Newmont Mining Corporation’s Eastern Nevada Operations commissioned its commercial biooxidation facility. The commercial biooxidation facility is a refractory gold whole ore heap process that uses bacteria to assist with the oxidation of sulfide minerals thus liberating occluded gold for further processing by cyanide for gold extraction. Before the commercial biooxidation facility was started, a decade of research went in to developing this state-of-the-art process. During final design and construction of the commercial facility a decline in gold price necessitated cost saving and project scope changes. As a result, the biooxidation process experienced many challenges. Some of the more significant challenges include poor heap permeability due to haul truck stacking, unhealthy bacteria population due to a lack of solution aeration, and insufficient biooxidation time because of limited pad space and high carbonate content in the ore. This paper discusses the many challenges encountered and addressed during the first 2-3 years of commercial biooxidation operation.

Jan 1, 2003

By David Akers, Clifford Raleigh, Glenn Shirey

Under a Cooperative Agreement with the U.S. Department of Energy’s National Energy Technology Laboratory (NETL) and the Mining Industry of the Future Program, CQ Inc. is demonstrating the GranuFlow™ process for improving the recovery of fine-sized coal in commercial coal preparation facilities. The State of Pennsylvania’s Energy Harvest Grant Program is also providing funding for this project. The GranuFlow technology involves the addition of an asphalt emulsion to a slurry of fine-sized coal (<100 mesh or 0.15 mm, typically froth flotation concentrate) before mechanical dewatering in screen-bowl centrifuges. The emulsion selectively agglomerates the carbon-rich particles, resulting in increased particle size and improved recovery of the coal fines during the dewatering process. This paper summarizes the test conditions and current results for both bench-scale investigations and full-scale commercial plant demonstrations.

Jan 1, 2005

By D. W. Leyshon

The fluidized solids technique for the calcination of phosphate rock has been well established for over 10 years. This paper is intended to review the recent performance of many of the Dorr-Oliver FluoSolids* calciners. In addition, design features of these three compartment refrac¬tory construction reactors will be described and a comparison made with fuel requirements for single compartment calcination. Also presented will be certain, aspects of the use of the rock including a discussion of non sulfate sulfur in the rock. A system is described for producing a blended mixture of calcined and uncalcined rock.

Jan 1, 1972