Search Documents

By Bruce Gellar

For the past six years, the author has made it a priority to attend the Prospectors and Developers Association of Canada’s (PDAC) annual conference. This most recent meeting took place March 10-13, 2002in Toronto, Ontario. In the three years since the author’s last PDAC report, the mining industry has undergone a severe trough. Some the industry’s woes included deeply discounted commodity prices, rampant layoffs, mergers, and overall avoidance by the investment community. However, at each of the PDAC conferences, the author has felt a heightened sense of excitement about the mining industry, more so than at other similar gatherings.

Jan 1, 2002

By James L. Hendrix, David Castillo

Cyanidation is one of the most common practices used in the extraction of gold and silver. One method of application is heap or dump leaching which entails the leaching of the gold or silver ore by spraying or dripping a cyanide lixiviant over the ore and collecting the effluent. The ore is placed on what is known as a leach pad system. A typical leach pad system consists of a foundation, a leakaqe detection system, a liner, and a cover layer (Strachan and van Zyl, 1988). There are many types of liners available for use. The type of liner depends upon what type leaching pad system us used. Generally, leaching pad systems can be categorized into two types: an expandable pad and a reusable pad. An expandable pad exposes the liner to the elements only in the initial stages of ore placement on the leach pad system. A reusable pad exposes the liner to the elements on a periodic basis. In addition to the exposure to the elements, the liner is also under the stress of the ore placed on it and the stress of the vehicular traffic across it. These stresses and exposure to the elements are the major causes of liner failures, which can appear as punctures, tears, cracks, and deterioration. Because of the possibility of the failure of the pads to contain cyanide-laden solutions the designs for liners of pads and ponds have become more and more stringent. Currently, though, there is some recognition that in some locales such stringent design criteria may not be required (Chatwin, 1989). Some soils have significant cyanide attenuation and degradation capacity. It has been found that soils containing carbon- aceous materia1 wi11 remove cyanide from solutions percolating through them (Chatwin, 1989). Of course metallurgists have long recognized the deleterious effect of carbonaceous material in the mill circuit. Sheridan, et a1 (1988) have shown that WAD cyanide is detected in the effluent of a 2 m column filled with ground carbonaceous ore only after it had been continuously washed with greater than 9 pore volumes of NaCN solution. It was decided to examine the potential of successfully attenuating cyanide by placing an organic material layer between a 1iner and the prepared soil base. One consideration for the selection of the organic material was cost. Sawmill wastes, ground agricultural wastes (such as corn cobs), and other organic wastes were considered. But the first waste to be tested was a product found at any metropolitan area, sewage sludge.

Jan 1, 1990

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

Operators of mining vehicles are exposed to high levels of whole-body vibration (WBV) and are therefore at risk of developing vibration-related health disorders. For implementing an effective control strategy, it is imperative to locate the source(s) of vibration, and the specific changes that might occur to the vibration signals during its transmission through the seats to the recipient human body. With this objective, Seat Effective Amplitude Transmissibility (SEAT) values of seat modules used in dumpers (n = 10) and other heavy earth-moving machines (n = 11) were evaluated in an iron ore mine. Vibration was measured simultaneously on the seat and on the cabin floor beneath the seat using tri-axial and uni-axial accelerometers. The study aims at determining the quality of seat modules of the transport and non-transport vehicles from the perspective of their natural resonance frequencies and capability of any such seat in reducing harmful vibration. The highest acceleration values were observed in the z-axis for all the dumpers. SEATrms values ranged from 78 to 133% and SEATvdv values ranged from 72 to 130% for the dumpers. For other HEMMs, SEATrms values ranged from 55 to 125% and SEATvdv values ranged from 56 to 123%. Mechanical vibration contains multiple frequency components. To understand the changes taking place to the different signals at these frequencies, 1/3 octave band analysis was carried out for the signals recorded both on the seat and the floor. There was significant attenuation (38 to 57%) at 4 Hz for three Dumper seats, whereas they resonated in the range of 1.6–2.5 Hz. The transmissibility(%) in the resonating frequencies ranged from 108 to 156%. Resonance frequencies for the remaining seven dumpers ranged from 3 to 8 Hz. The spine has been reported to resonate at 4 Hz, whereas resonance at 1.6 Hz has little significance to human beings in regard to WBV of a seated person. Hence, the characteristic resonant frequency of 4 Hz of seats as observed in the present study has the potential of causing adverse impacts on spinal health. Evaluation of SEAT factors and resonance characteristics of seats are therefore recommended to be examined while selecting a mining vehicle for regular deployment in mines.

Mar 12, 2021

By AMIT SHARMA, BIBHUTI BHUSAN MANDAL

This paper describes the vibration transmissibility characteristics of mining vehicle seats under dynamic conditions in an opencast iron ore mine. Magnitude and frequency contents of vibration signals on the seat floor as well as on top of the seats were measured to record the change during transmission. The conventional rigid seats were found to resonate at about 4 Hz, which coincides with the resonance of the human spine. The pneumatic suspension seats also proved to be more efficient in attenuating the overall vibration energy transmitted from the vehicle chassis to the human body.

By Willard C. Lacy

INTRODUCTION A program to insure adequate talent for development and management of our mineral resources entails two equally important and interrelated aspects: 1) attracting and retaining promising student talent, and 2) providing a first-rate education for those entering careers in mineral science and engineering. Manpower shortages have eased in many areas of engineering, particularly in those areas dependent directly or indirectly upon government contracts in space and war programs. However, in the minerals industry the needs still remain critical. As increasing concern over preservation of the environment has developed, the political and social reaction was to seek out major offenders, to look for "whipping boys" -- and the mineral industry was, and had been, an offender. It was there for everyone to take pictures, it couldn't be covered up, and the Department of the Interior lashed away in the beautiful and popular brochures: Quest for Quality, The Third Wave, The Population Challenge, and Surface Mining and Our Environment (Ravaged Land). The Sierra Club, the Field and Stream magazine, TV, and daily news media added their lashes. In the minds of our social-conscious youth the mineral industry took on the image of "exploiters" of natural resources; "polluters" of streams, lakes, and the atmosphere; "despoilers" of wilderness areas and scenic beauty -- a plague to combat, rather than an exciting challenge that entailed exploration of the remote, conquering of the primitive, and developing of the undeveloped. Enrollments declined and many traditional mineral engineering curricula were abolished or Integrated into other stronger engineering departments to meet student-faculty ratio requirements.

Jan 1, 1971

By Robert F. Conley

This paper describes attrition milling as exemplified in rotary and vibratory mills for ultrafine grin¬ding application Without attempting to narrate the differences between various devices, generalized differences between the broad categories of rotary and vibratory milling are presented and compared with the ball mill Applications of these mills for coal, limestone, kaolin, mica, talc and iron oxides are described giving specific differences of the mineral properties that affect their behavior in the grinding mills Where applicable, specific recommendations are provided for ultrafine grinding of various industrial minerals

Jan 1, 1983

By Robert F. Conley

Attrition milling, once employed exclusively for the dispersion of pigments, has in recent years found a host of new applications in the area of mineral processing and mineral-pigment production. Broadly categorized, attrition milling is divided into two classes, as defined by the machinery's function, vibratory milling and rotational milling. Each mill type has been defined as a variation on ball milling and the terms, "vibratory ball mill" and stirred ball mill" appear in the literature. The primary design differences between attrition and ball mills are: (1) a stationary canister (or shell) (2) smaller grinding media (3) grinder energy is motor limited rather than gravity limited (4) strong media/feed size dependance.

Jan 1, 1983

By Richard D. Nichols

A new method of slaking lime has been developed by DENVER EQUIPMENT DIVISION of Joy Industrial Equipment Company and patented under U. S. Patent 4,261,953. The new method utilizes an attrition machine, commonly used in mineral processing circuits as a sand scrubbing device, to slake lime. The scrubbing effect of the attrition slaker continuously produces a fresh reactive surface so that further slaking may occur. This process allows for utilization of slaking all grades of burnt lime and most grades of dolomite lime. Testing indicates that poor grades of water usually not considered for this service can now be tolerated using the attrition slaker. The slaked lime produced is of higher quality, faster reacting and much less apt to produce scaling problems than previously experienced. The attrition slaker can be combined with a spiral classifier and ball mill to eliminate any need for grit handling or grit removal. The attrition slaker can be designed for all burnt lime tonnages up to the limit of 175 tph and 1" pebble lime size. Control can be maintained easily with minimal operator assistance. The equipment, the principals of process metallurgy, and the above topics will be presented.

Jan 1, 1982

By John C. Gathje, Gary L. Simmons

Power Point slides

Jan 1, 2000

By L. W. Saperstein

One of the most critical skills developed by underground coal miners is the ability to interpret natural warning signals in terms of impending roof failure. A miner receives a variety of signals which can be called warning and which can be classed broadly by sense: aural, visual, and tactile. This paper concentrates on those signals which are airborne and audible. These signals are creaks, cracks, pops, groans, snaps, booms, tears, rips, and other assorted pulses which emanate from the roof strata, coal pillars, and artificial support in response to the stresses induced by the mine opening. These pulses are sometimes referred to as "talk". Although it is clear that miners rely on roof talk to assess the roof's stability, it is not clear of what roof talk is composed. It has been described in a variety of figurative ways, but has not been scientifically characterized. As will be shown shortly, the purpose of this research is very specific. The ramifications, however, are very broad, and are, indeed, still being followed.

Jan 1, 1974

By J. Moreno, P. Sinton, R. Vogwill

Groundwater models are often used to estimate and optimize dewatering volumes, locations, and rates, as well as water supply production for mines. Projections of future dewatering rates are highly dependent on the conceptual model used as a basis for the numerical model. This paper presents an audit of modeled dewatering rates versus actual data and an examination of the reasons for discrepancies. The setting is a gold mine, in a collapsed volcanic crater breached by the ocean. Mining will occur to about 200m below sea level within a remnant geothermal system. A detailed hydrogeologic investigation was conducted to support dewatering and geothermal depressurization design for future mining operations. These studies included development of a three-dimensional model to simulate heat and density-coupled groundwater flow, using software developed by URS/Dames & Moore. In this paper, the groundwater modeling results prepared 5 years previously by others was audited using operational dewatering data. This model was then extended using the new mine schedule and actual locations for dewatering wells to predict future dewatering requirements. In addition, a comparison between “hot” and “cold” model results was used to assess the need to use a heat-coupled versus a standard groundwater model for dewatering predictions.

Jan 1, 2003

By S. R. Dismukes

Mining is likely to be targeted by The United States Environmental Protection Agency (“EPA”) as one of its key enforcement targets for fiscal year 2002-2003. Identifying the mining industry as an enforcement target, coupled with an increase in enforcement activity in recent years, places each mining operation at increased risk of receiving enforcement attention. A properly developed and implemented Environmental Management System (“EMS”) tailored for your operation is invaluable in reducing the risk of incurring liability for non-compliance. At the heart of an effective EMS is an audit program that checks the company’s compliance with environmental requirements. In addition, audit privilege (in select states), voluntary self-disclosure, and the attorney-client privilege serve as very effective tools for managing those liabilities that may arise during auditing a well-developed program. Of course, these latter tools are effective only if the auditing program is properly structured and properly managed. EPA and some states also provide varying degrees of immunity for environmental violations that are voluntarily disclosed in writing by the company. However, self-disclosure laws and policies typically prescribe stringent requirements for parties seeking to take advantage of them. For example: U.S. EPA has recently extended the time period in which to provide full written self-disclosure to 21 days. However, U.S. EPA’s revised Self-Disclosure guidance also addresses when a company obtains knowledge of a violation for purposes of triggering the 21-day clock and specifically extends the knowledge requirement to include the company’s agents and consultants. This expansion increases the difficulty companies may have in clearly defining and managing when they obtained knowledge. This difficulty increases the importance of managing factual development and the strategic use of other

Jan 1, 2001

By D. J. Hutchinson, S. Nickson

Cable bolts are used as a means of rock support around underground excavations in many mines across Canada and around the world. A substantial body of research on cable bolting was conducted at a number of Canadian universities and mines from the mid-1980s through the 1990s. Since then, research into selected areas of cable bolting practice has continued in Canada. The research has focussed on cable bolt instrumentation and on the inclusion of cable bolts in empirical stope design techniques. A review of cable bolting practice is now warranted at many mines. It has been five years since the completion of the previous substantial body of Canadian academic research and the associated advancement in understanding of cable bolt design, implementation and verification practice. Attempts were made at that time to transfer the new design procedures and performance assessment technologies to mine-site personnel. In some cases, this was effective, and ground control personnel continue to improve on their cable bolting practice at each specific mine site. However, at other sites, experienced people have moved on, and the new, less experienced personnel do not have access to the training or technical resources required to improve their understanding of the subject. In other cases, the technology was not transferred effectively to practitioners, with the result that substantial improvements can be made to the cable bolting practice at those mines. Guidelines for auditing cable bolting practice are provided in this paper. The guidelines include a discussion of the objectives of the audit, suggestions for audit procedure and a summary of the possible outcomes of a cable bolt audit. The objectives of an audit might include assessing the reasons for unexpected cable bolt failures, evaluating the quality of the installation procedures, quantifying the efficiency of the cable bolt system and assessing training requirements and procedures. A cable bolt audit should include consideration of all aspects of the cable bolting cycle, including the design, implementation and verification phases of the operation. At the end of the audit, a ranking should be assigned to the components of the cycle. The ranking system can then be used to identify items that require immediate attention, others that could be improved and others that are adequate. Following completion of a cable bolt audit, increased confidence in the support system and its application is generally, found, along with the potential for cost savings in many cases.

Jan 1, 2002

By G. E. Welch

The paper discussed the mechanics of an environmental audit. Commonly encountered problems and situations are discussed and guidelines are given to aid prudent decision makers in evaluating audit results. The merits and benefits of an external view will be given. The paper will highlight the reduction of risk through pre-acquisition and operational audits.

Jan 1, 1992

By Wade N. Ellett, K. Marc Le Vier, Timothy A. Fitzpatrick, Kenneth A. Brunk

As the gold mining industry matured through the 1980' s, and into the 1990's, the development of refractory gold orebodies has become more prevalent. Newmont Mining Corporation developed and commercialized flash chlorination for the treatment of carbonaceous preg robbing ores; Homestake Mining Company developed and commercialized the industry's first application of autoclaves. Barrick installed the world's largest autoclaves on whole ore treatment a few years later. Dry grinding and roasting followed at Placer Dome's Cortez, Freeport -Independence and Newmont's Carlin operations. Today, numerous papers are presented on research efforts worldwide which address treatment of refractory gold ores by bioxidation, roasting, autoclaving, alternative lixiviant treat­ment and other novel process ideas. The overall objectives are to develop economic processes for difficult refractory ores where no process exists or conventional practice is cost prohibitive. Successful research can lead to lower operating costs, increased profits, and increased ore reserves. One such research effort directed by E I DuPont de Nemours and Company, Advanced Mining Technologies, was focused on gold ores which were refractory in nature due to the cyanide soluble copper content. Approximately five years of research effort culminated in a patented process (U.S. Patent 5,411,575)1 and the formation of a new joint venture company, AuGMENT Technologies, in 1995 with Newmont Mining Corporation. Today significant progress has been made in moving the laboratory scale tests to commercialization.

Jan 1, 1997

By Gerald Zink

The work described in this paper is sponsored by the Bureau of Mines for the purpose of accelerating the drilling of roof bolt holes and reducing the quantity of materials needed to fill each hole. A high-speed small-hole drill has been fabricated and tested in the laboratory. High priority has been given to safety, reliability, and compatibility with underground coal mining practice. The combination of drag bits and erosion jets is designed for high penetration rate, long wear life, and uniform hole size in a variety of sedimentary strata. A reliable high-pressure high-speed swivel feeds water to the bit at about 4 1/min (1 gpm). The duplex hydraulic intensifier which drives the jets has a 40 kw capacity (30hhp) Results of recent full-scale laboratory testing are presented.

Jan 1, 1978

By B. Denby, R. Hollands, S. Cooper

Augmented Reality (AR) is a technology that can be used to mix computer-generated images of data with views of the real world. The University of Nottingham is developing AR technology in a major research project which can be used to assist mining companies in visualising complex mine data whilst out in the field. The technology comprises of integrated GPS surveying technology and electronic orientation devices to provide location and viewing information, video capture via digital camera and portable computing hardware to overlay 3D models on views of the real world. The paper describes the concepts of the technology in some detail and concentrates on the possible applications of this in the surface mining and exploration industries.

Jan 1, 2002

By Ji Fang, Chong Fan, Fengrui Wang, Dongxin Bai

Unmanned mining technology in underground mines offers high efficiency, safety, and low cost. However, ground operators face challenges in accurately perceiving the underground environment through videos. This paper presents an augmented reality (AR) platform developed to enhance the unmanned mining process. The platform uses cameras and 5G technology to transmit high-fidelity video streams to the ground, where key targets are identified and virtual models are registered in the video to enhance the real scene. Tests in the Xinli stope of the Sanshandao gold mine showed the platform’s effectiveness in improving ground operators’ perception and production efficiency.

Jan 30, 2022

By Amy McBrayer, Vladislav Kecojevic, Juan David Valencia Quiceno, Dragan Bogunovic

The mining industry’s commitment to innovation reflects a history of adopting technological advancements to enhance workplace safety, environmental sustainability and vocational training. The objective of this research was to develop an augmented- reality (AR) system for heavy-equipment operators (HEOs) in surface mining. The developed system has the potential to enhance mine safety, training and data-driven decision- making, which presents a significant step toward a more sustainable, effective and technologically driven mining training, contributing to the industry’s evolution and growth. The AR training system leverages Microsoft’s Power Platform and HoloLens 2 capacities to provide operators with detailed and immersive training guides for three mining equipment, including bulldozers, motor graders and haul trucks. AR guides combine speech controls, 3D objects, informative images and explicative videos in the real working conditions to enhance the operator’s learning process. The system has the potential to modify the training structure based on user performance and provides an efficient approach to data collection during training. This project was developed and applied through a case study in a surface mine in the Southern United States.

Feb 1, 2025

By Haydn H. Murray

Kaolins and bentonites of economic importance in Australia and New Zealand are described. Clays that are used for structural clay products are not discussed. Residual, hydrothermal, and sedimentary kaolins are utilized including clays associated with coal measures. Bentonites are sedimentary and residual. Very little kaolin and no bentonite is exported presently, but this will change in the near future as transportation costs continue to escalate. Many areas of Australia, in particular, where kaolins are known to occur have not been investigated to determine the quality and quantity of the deposit.

Jan 1, 1982