Search Documents

By A. Robles-Vega

In recent years, tellurium has been extensively used in the manufacture of semiconductor materials. For this type of application, high-purity tellurium is required. Selenium, lead and silicon are usually the main impurities in tellurium. During the electrolytic refining of copper, tellurium gold and silver are collected in the anode slimes. A pyrometallurgical treatment is used to recover gold and silver from the decopperized anode slimes whereas tellurium is oxidized and skimmed off from the refining furnace as a Na2CO3-based slag. In the slag, tellurium is present as sodium tellurite (Na2TeO3), which is further water-leached from the slag. The first step in the conventional process for tellurium recovery consists of the precipitation of the tellurium contained in the leaching solution as tellurium dioxide (TeO2). The solid TeO2 is then dissolved under acidic conditions for its further reduction with sulfur dioxide gas (SO2). In this paper, an alternative route for tellurium production is presented in which a sodium tellurate [Na2TeO4] intermediate is obtained by oxidation of the sodium tellurite in an alkaline solution following the water leaching step. Sodium tellurate is then dissolved in acid media and high-purity tellurium is obtained by reduction with SO2 gas. Experimental tests under laboratory conditions indicate that the novel process yields higher precipitation selectivity for tellurium than the conventional process. A comparison of its efficiency concerning impurities co-precipitation with respect to the conventional process is discussed.

Jan 1, 2009

By G. T. Lineberry

The Work Crew Performance Model (WCPM) is a method for designing, implementing, and evaluating? performance improvement strategies for machine operators and other mining personnel. The WCPM offers a practical approach for measuring job proficiency and identifying costly behaviors. It enables interventions aimed at performance improvement, especially training, to be assessed monetarily. Two interrelated elements of the WCPM are emphasized: observational techniques for establishing performance baselines and measuring performance outcomes and cost linkages between job competencies and measures related to profitability. Inter-and intra-subject differences in performance-related behaviors of regular and incidental shuttle car operators were detected during field validation of the WCPM. Downtime data were used as outcome measures to test linkages between performance error rates and cost consequences. Use of a simulation program for analyzing continuous mining face operations showed how common shuttle car operating parameters (e.g., payload, tram rate) can be used as cost-conscious indicators of performance variability and therefore as targets for performance improvement.

Jan 1, 1994

By Erik Westman, Brandon Stables, Benjamin Mirabile

"Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of standing support and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data.INTRODUCTIONA hydraulic load cell, more commonly known as a flat jack or JackPack, is a device installed to determine the loading characteristics of the roof-to-floor supports. These standing or roof-to-floor supports include, but are not limited to pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports.Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. Preloading helps to keep the supports, such as timbers props and cribs, in place during the dynamic loading associated with blasting (Barczak and Tadolini, 2004).Flat Jacks are manufactured in various shapes and sizes depending on the application; common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed, as shown in Figure 1. These load cells are produced in South Africa and can be formed into several different shapes depending on the application (Barczak, 2003). The sheet metal that makes up the bladder is comprised of 19-gauge or 1.11 mm (0.04 inch) thickness; the top and bottom pieces of sheet metal are resistance-seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow fluid to fill the unit, and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1,724 kPa (250 psi), the pressure relief valve keeps the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure.The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements, a pneumatic powered pump, hydraulic pump, or hand pump may be required to inflate the load cells."

Jan 1, 2019

By B. Mirabile, B. Stables

Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of a standing support, and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data. INTRODUCTION A hydraulic load cell, more commonly known by “flat jack” or JackPack, is a device installed to determine the loading characteristics of roof to floor supports. These standing or roof to floor supports include, but are not limited to: pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports. Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. These load cells are produced in South Africa, and can be formed into several different shapes depending on the applications (Barczak). Flat Jacks are manufactured in various shapes and sizes depending on the application, common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed as shown in Figure 1. The sheet metal that makes up the bladder is comprised of 19 gauge or 1.11125 mm (0.04375 inch) thickness, the top and bottom pieces of sheet metal are resistance seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow a fluid to fill the unit and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1724 kPa (250 psi), pressure relief valve will keep the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure. The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements a pneumatic powered pump, hydraulic pump or hand pump may be required to inflate the load cells.

Jan 1, 2019

By Ron Parks

High Pressure Grinding Rolls (HPGR) was introduced to the mineral processing industries in the mid-SO's as a tool for comminuting raw and processed materials. This tool made its an impact in the Cement Industry where it was used as a pre-grinder on existing ball mills, raw and finish grinding in a mill circuit and other various applications. This concept was a big success where the cost of power was high along with the desire to increase capacity. The HPGR reduced the power requirement and increased the capacity in the ball mill due to the finished product produced by the HPGR and the micro fractures in the coarse rock, which reduces the power required to finish grind the rock. This unit has found acceptance in many other industries including diamonds, iron and other selective applications. The diamond industry uses this tool for selective grinding purposes since the kimberlite rock is considerably softer than the actual diamonds. Therefore within a bed of material, kimberlite is crushed to fines and the diamonds are liberated and unharmed. The iron industry primarily uses this tool for concentrate comminution; however, there are installations using this tool as a pebble crusher and in an AG-pebble mill circuit.

Jan 1, 2000

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 19601s, is still proceeding. The largest mechanical flotation machines available today have unit volumes in the range of 38 to 42 m3 (1,350 to 1,500 cft). In fact, the motivating forces of increasing capital and energy costs and decreasing ore grades, which created the need for large flotation cells, not only still exist, but are becoming more critical. This paper reports the development of an improved mechanism for these large flotation machines. The starting point in the development of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1982

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 1960's, is still proceeding. The largest mechanical flotation machines avail-able today have unit volumes in the range of 38.2 to 43.9 M3 (1,350 to 1,550 cft). Designs for mechanical flotation cells of unit volumes as large as 70.8 m3 (2500 cft) are available. The development of these "giant" flotation machines has been and continues to be motivated by the increasingly critical forces of higher energy and capital costs, decreasing ore grades, and lower (real) prices for the products. As an expansion of a previous publication, this paper reports the further development of an improved mechanism for these large flotation machines. The starting point in the develop¬ment of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which s is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1983

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) has been used by the mining industry for early fire detection in underground mines. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to integrate real-time AMS sensor data with NIOSH’s mine fire simulation program, MFIRE 3.0, to simulate and predict the spread of smoke that would provide assistance to mine fire emergency response personnel. Determining the heat release rate of a fire using the monitored sensor data was a critical component of the successful completion of this project. NIOSH researchers developed a direct method to calculate the heat release rate when a fire is within close range of sensors. However, this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire heat release rate for complicated scenarios where a fire is distant from sensors and airflow splits and merges are present. The method was validated using a fullscale diesel fuel fire test conducted in the Safety Research Coal Mine at the Pittsburgh Mining Research Division and can help mine operators and safety personnel make informed decisions during a fire emergency.

Jul 31, 2020

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) is used in the mining industry for early fire detection. Researchers at the U.S. National Institute for Occupational Safety and Health (NIOSH) have developed a direct method to calculate the fire heat release rate (HRR) when a mine fire is close to the AMS sensors, but this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire HRR using AMS sensor data at any location downstream of the fire. The method was validated using a full-scale diesel fire test conducted in the Safety Research Coal Mine at NIOSH’s Pittsburgh Mining Research Division.

By Anthony G. Fonseca

The acid leach-solvent extraction processing of oxide copper ores can be improved when selected cation additives are utilized. Bench scale testing showed improvements in both sulfuric acid leaching and solvent extraction processing. Treatment with the method to be described shows improvement in copper recovery in the acid leaching section as well as reduced acid consumption and reduced iron and aluminum dissolution. Processing the copper bearing leach solution with LIX-64N shows increased loading of the LIX reagent which relates to reduced aqueous and organic flow rates, reduced organic loss and inventory as well as a reduction in the size of mixer-settlers. The use of selected monovalent cations controls fluctuations within the pro- cessing system to accomplish the above named improvements. Additionally, these cations are totally compatible throughout the processing system and are quite inexpensive. Bench scale recycle data will be presented both for the leaching section and the continuous solvent extraction processing section up to (but not including) processing the loaded electrolyte. Material balances as well as major solution component monitoring will also be presented.

Jan 1, 1975

By M. M. Fine

One of the most persistent topics at technical gatherings and in the recent scientific press has been the reduction of iron ore. To cite some of them, in May 1960, a symposium on the subject was sponsored by the Electrochemical Society. The proceedings, comprising two dozen papers, were later published.3/ More recently, November 1966, a similar gathering took place at Michigan Technological University, Houghton, Mich. The latest meeting was the International Congress on Production and Utilization of Reduced Materials, Evian, France, May 1967. If the volume of literature, symposia and conferences is a measure of industry concern, then current interest must be at a high level. To the casual observer of the metallurgical scene, the abiding and recurring attention to iron ore reduction outside the blast furnace must be somewhat puzzling in that so much research endeavor has resulted in so little commercial activity.

Jan 1, 1968

By H. D. Freeman

The Pacific Northwest Laboratory (PNL) is developing cover technology for uranium mill tailings that will inhibit the diffusion of radon to the atmosphere. As part of this cover program, an improved radon flux measurement system has been developed. The radon measurement system is a recirculating, pressure-balanced, flow-through system that uses activated carbon at ambient temperatures to collect the radon. With the system, an area of 0.93 m2 is sampled for periods ranging from 1 to 12 h. The activated carbon is removed from the radon trap and the collected radon is determined by counting the 214Bi daughter product. Development of the system included studies to determine the efficiency of activated carbon, relative calibration measurements and field measurements made during 1980 at the inactive tailings pile in Grand Junction, Colorado. Results of these studies are presented.

Jan 1, 1981

By L. G. Austin

The model originally proposed by Austin, et al., has been modified in the light of further investigation of the breakage laws in SAG milling. The model uses a fully-mixed reactor for short L/D mills and calculates the breakage of small particles by the nipping action of balls and pebbles. The autogenous self-breakage of larger lumps is treated as an effective means of fast breaking rock and much slower breaking rock. Experiments show that fast autogenous breakage can be treated as a first-order breakage with an overall specific breakage rate which incorporates fracture and chipping. Similarly, slow breakage incorporates fracture and abrasion. Autogenous breakage is cushioned by the accumulation of fine material. Simulation results are compared to results from tests in a 2 m diameter continuous pilot-scale SAG mill. Future work is discussed.

Jan 1, 1985

By Thomas E. Ban

The continuous sintering process was invented more than 60 years ago by two metallurgists, Arthur S. Dwight and Richard L. Lloyd, who saw a need for automation in mineral processing. Their specific objective was to beneficiate copper ore by desulfurizing and agglomerating it for copper blast furnace smelting at the Cananea plant in Mexico1. Since their early development the process expanded widely in scope, size, and application. The current worldwide sintering applications exceed 250 million tons per year for agglomerating ores of lead, manganese, zinc, and iron. Sintering is also widely used for production of sintered lightweight aggregate from clays, shales, and fly ash. The continuous sintering process took on wide expansion during the 1960's in foreign countries. Plants for production of approximately 135 million tons per year were built in these countries for sintering iron ore fines as shipped from new iron ore projects of Canada, Liberia, India, Brazil, and Australia. This expansion represented construction of approximately 80 new sintering plants, some as large as 15 thousand tons per day production on a single large sintering machine. Sized self-fluxing or highly fluxed sinter has become recognized as a premium blast furnace charge and has enabled blast furnaces of Japan and Europe to produce upwards of 10,000 tons of metal per day with coke rates less than 1,000 pounds per ton of metal. This coke requirement is practically 50 percent of the ordinary rates achieved during the early 1950's when the peak blast furnace production was less than 113 of the current records.

Jan 1, 1975

By Richard R. Radel, Jack Barry

Contract required excavating 2,000 If of 14' horseshoe tunnel in rock, a 95' deep work shaft on shore, and a 50' deep intake shaft located in the middle of the Niagara River just above Niagara Falls. Large quantities of H2S were encountered in the range of 20 PPM with ventilation. Peak levels of 40 PPM were recorded. The original designed ventilation system required only a volume of 10,000 CFM to meet OSHA requirements. The volume of air was increased to 50,000 CFM to dilute the H2S to al- low workmen to work and comply with OSHA H2S action levels. The second phase of the tunnel consisted of placing 72" ID X 20 foot long concrete reinforced pipe in the tunnel. When the tunnel was holed through and both shafts were open, a substantial amount of work was required to take place in the shafts which eliminated the possibility of placing a bulkhead to secure proper ventilation. The ventilation team designed a jet system airlock. The design of this system was to bring fresh air down the work shaft in two duct systems; one 30" diameter and one 24" diameter. Following the excellent work of Jan Wolski (7th Mine Ventilation Symposium chapter 58) our design incorporated nozzles located approximately 100' in by the work shaft. The velocity of the 24" diameter duct was 6,365 FPMD2.2 MPH. The velocity of the 30" diameter duct was 6,117 FPMl69.5 MPH. Both systems were on blow and being that air expands at 3112 degrees per side this high velocity of air expanded and created an air bulk head through which men and the large sections of concrete pipe could be passed without any delay or additional cost to the project.

Jan 1, 1997

By J. Leonard Frame

A coal-fired fluidized bed combustion (FBC) system will be installed at the Owatonna Tool Company, Owatonna, Minnesota. Two FBC combustors will burn solid fuels: coal, petroleum coke, and wood and paper wastes. Crushed dolomitic limestone will be used to control sulfur emissions to EPA limits. The combustors will supply indirectly heated hot air and hot water for paint drying operations, washing processes, and space heating. The program is sponsored by the United States Department of Energy and the Owatonna Tool Company, and is one of five programs designed to demonstrate industrial applications of coal-fired fluidized bed equipment. The paper will describe the combustion system and the results of development tests with dolomitic limestone for sulfur emission control.

Jan 1, 1978

By D. W. Ashman

Today the electrolytic zinc industry is facing unprecedented environmental pressure and low metal prices. Zinc plants have to decide how they will dispose of iron residues in an environmentally friendly way without major capital expenditures. Only low-cost producers will survive, so companies must continuously improve to stay competitive. Therefore, the challenge of the process engineer is to find innovative solutions to the industry's problems. This paper reviews the status of electrolytic zinc processing and provides some insight into how the industry will respond to the pressures facing it

Jan 1, 1993

By Norm Greenwald

The Environmental Protection Agency ("EPA") has been attempting to develop a federal regulatory program for mine waste under Subtitle D of the Resource Conservation and Recovery Act since 1986. Recent regulatory and legislative events are now bringing this goal closer to reality. This paper discusses the mining industry's perspective on a number of the issues currently being addressed at EPA's Policy Dialogue Committee and in Congressionally-sponsored negotiating sessions.

Jan 1, 1992

By Leping Liu, Sachin Urade, Li-Ting Chen, Pengbo Chu

This study aims to provide industrial perspectives on the current U.S. metal mining engineering education and areas for improvement. An online survey was designed to seek opinions from the U.S. mining industry. Findings indicated a shortage of qualified graduates from the current U.S. metal mining engineering education system. The qualifications that need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications, such as the ability to acquire and apply new knowledge as needed and sufficient field experience. Respondents recommended enhancing collaborations between industry and academia.

Oct 1, 2023

By James R. Jones

The purpose of these opening remarks is to establish a viewpoint, which will form part of the basis for later discussion between panel members and between the panel and the audience. Important issues will be identified. These ideas in the form of questions and answers, hopefully, will provide the necessary background for the ensuing dialogue. Is There An Urgency? We do not believe there is the urgency for immediate control legislation that has been depicted by some Congressional sources, environmental groups, and certain segments of the press. Emissions of sulfur oxides in the United States have decreased 15% during the 19701s, even though the use of coal by electrical utility power plants increased nearly 80%. That trend will continue as the older plants are phased out of operation and are replaced with newer plants, which must meet the New Source Performance Standards (NSPS) requiring the use of "scrubbers" to reduce sulfur dioxide emissions by 70% or 90%. The present Clean Air Act Amendments of 1977, by allowing the logical progression of economic events- -depreciation, retirement, replacement, and growth--will produce approximately a 50 % reduction in SOX emissions by the year 2015.

Jan 1, 1984