Search Documents

By J. N. Van der Merwe

Following the Coalbrook disaster in 1960, research into coal pillar strength resulted in the adoption of the concept of a safety factor for the design of stable pillars in South African coal mining. At the time when the original statistical analysis was performed by Salamon and Munro in the early 1960s, 27 cases of failed pillar workings were considered suitable for inclusion in the database of failed pillars. Pillar failure did not stop after the introduction of the safety factor formula by Salamon and Munro (1967). In the ensuing years, pillars that were created before the application of the formula deteriorated and later failed, as did ones that were created after the introduction of the formula. This means that over time, the database of failed pillar cases increased in size, allowing ever more reliable analyses to be performed. The number of failed cases in the database had grown from the original 27 in the 1960s to 86 by 2011. All the failed cases are contained in the updated database. The database of stable pillars, which is also used in the derivation of strength formulae, has now been extended from 125 to 337 cases. The new database of intact pillar cases is more complete as it bridges the time gap between the Salamon and Munro (1967) and the Van der Merwe (2006) databases. The original requirements for inclusion into the database were satisfied in the compilation of this latest collection. The characteristics of the original database of intact pillars did not change in a meaningful way. The mining depth and pillar dimensions of the new database are largely as they were in the original database. Time-related trends with regard to pillar dimensions and depth of mining could not be found, indicating that the geometrical parameters of coal mining in South Africa have not changed meaningfully in approximately a century of mining. The characteristics of cases in the updated database of failed pillars does not differ substantially from the one published by Van der Merwe (2006). The same difference between that database and the original Salamon and Munro database, namely that the average safety factor of the failed cases had increased dramatically, from 1.0 to 1.5, is still apparent. This may be due to the inclusion of more failures from specific areas that exhibit a disproportionate number of failures at higher safety factors. These areas are the Vaal Basin, Klip River, and Free State coalfields. The new database confirms yet again that there is no correlation between the safety factors of failed pillars and their time of failure. The safety factor on its own is thus not a reliable predictor of longterm stability of pillars. Keywords coal pillar, stable pillar cases, pillar collapse, pillar data base.

Nov 1, 2013

By L. A. Cornish

Pt-based alloys for high-temperature applications in aggressive environments have been under development for over 10 years, and are targeted to be used as either as bulk, or as coatings. The alloys comprise Pt, Al, Cr, and Ru, and the microstructure has been improved by composition to a best possible analogue of the nickel-based superalloys, which these alloys could partially replace. This was necessary because the previous best alloy had a strengthening precipitate volume proportion of only approximately 40 vol.%, whereas the nickel-based superalloys have around 70 per cent, and a lower volume would mean that the strength would not be the best that could be obtained. The microstructures were assessed using electron microscopy, and have been related to the alloys? hardness values. The current microstructures are much more like those of NBSAs, with a high proportion of the strengthening ~Pt3Al precipitates. Since the samples have to be small (platinum is expensive), hardness has been used as an indication of strength. Nano-indentation studies showed that the hardness and Young?s modulus were higher for ~Pt3Al than the (Pt) matrix. More extensive oxidation studies have been undertaken on the previous optimum sample, and the effect of cooling rate after heat treatment has also been ascertained. In addition, the samples were studied after different heat treatment times, and cross-sections were made in order to characterize the alumina scale that formed. The oxide scales of Pt-11Al-3Cr-2Ru (at.%) up to 100 h exposure did not spall, and were at least as good as those of the ternary alloys. There was no discernable Al depletion zone in the substrate, although it could have been at a greater depth than thickness of the samples studied. Further additions to the Pt-Al-Cr-Ru alloys have been studied, to increase the melting temperature as well as to reduce the platinum content without compromising the properties. Reduced platinum content would have the benefits of reduced density and cost. The target elements include vanadium and niobium, of which vanadium is of special interest, since it is a South African product. Before these additions could be made, phase equilibria studies were undertaken so that the maximum addition could be ascertained, and also to check any possible ternary phases, which could be deleterious. Work on the Pt-Al-V system revealed a ternary phase, ~V27Pt54Al19 (at.%), which has a eutectic reaction with (Pt). The maximum V addition is likely to be around 15 at.%, otherwise ~Pt3V or the ternary phase will form, and not the required (Pt)/~Pt3Al phases.

Jan 1, 2012

By David J. Blackwell

The challenge; to design production facilities and in particular separation equipment which have the ability to deal effectively with the ever changing composition of well fluids, over the life time of the field in which it is operating, ensuring maximum uptime of the asset coupled with consistently effective separation. Design engineers are, however, continually confronted with a dilemma when selecting materials of construction for Oil/Gas separation equipment, since they are generally obliged to select an acceptable material of construction, based on ?predicted? operating conditions, at the lowest acceptable cost. Consequently many designs are somewhat basic and do not take into account the constantly varying dynamics of the well fluids being released into the separator. As oil fields mature, oil companies endeavour to maximize revenue by maintaining oil and gas throughputs. This often results in an associated increase in water and sand volumes and, in order to maintain efficient separation, an increase in operational temperature and pressure; subjecting the equipment to operational conditions for which it was never designed. In reality, therefore, the limitations and constraints placed upon new construction design often result in Maintenance Engineers having to solve the ensuing problems in difficult ?in-field? environments. Should refurbishment or upgrade be required then the status of the platform and that of the vessel during shutdown will dictate how this is achieved. Hotwork on the vessel is generally not preferred due to the requirement for post weld heat treatment and re-classification of the pressure vessel, not to mention the added risk in terms of safety. Unfortunately, until recently, there have been few alternatives to conventional ?hotwork? repair and protection systems, especially since the performance of cold curing polymer based repair and coating systems, for use in oil and gas process equipment, has, until recently, been limited by their resistance to temperature and pressure in immersed conditions. In line with the continued development of high temperature / high pressure oil and gas fields however, recent breakthroughs in polymer technology can now offer both repair and protection solutions which are able to function effectively at temperatures up to 180°C in immersed conditions combined with resistance to the destructive forces of explosive decompression from pressures in excess of 90 bar. This paper will look at recent work that has been undertaken to determine the suitability of modern polymer based repair and protection systems as an alternative to hotwork; thus enabling newly designed and upgraded internals to be cold bonded into position and further protected with temperature resistant coatings, in order to minimize the downtime of the asset and further to protect the vessel internals from the Erosive Corrosive environment.

Jan 1, 2006

By W. Wittke, D. Schröder, H. Polczyk

ABSTRACT: The Urft dam, the Diemel dam and the Eder dam are three old masonry damslocated in Germany. The paper describes the rehabilitation measures and the correspondingstability analyses carried out to adjust the dams to today's standards. Remedial works such as theexcavation of inspection galleries, the installation of a grout curtain with a downstream drainagescreen as well as the installation of pre-stressed permanent tendons were carried out. In all threecases the stability of the upgraded dam could be proven on the basis of finite element analyses. ZUSAMMENFASSUNG: Die Urft-, Diemel- und Edertalsperre sind drei alte deutscheSchwergewichtsmauern aus Bruchsteinmauerwerk. Im Beitrag werden Instandsetzungsmaß-nahmen und Standsicherheitsnachweise beschrieben, die erforderlich waren, um die Staumauernan den heutigen Stand der Technik anzupassen. Hierzu wurden Kontrollgänge aufgefahren,Dichtungsschleier mit luftseitiger Dränage sowie vorgespannte Daueranker hergestellt. In allendrei Fällen konnte unter Berücksichtigung der Instandsetzungsmaßnahmen die Standsicherheit derMauer auf der Grundlage von Berechnungen nach der Methode der finiten Elemente nachgewiesenwerden. RÉSUMÉ: Les barrages de Urft, Diemel et Eder sont trois barrages-poids vieux allemandsconstruit de maçonnerie de moellon. Dans cet article, opérations de remise en état et preuves destabilité sont décrits, qui étaient nécessaires pour adapter les barrages à l'état de la techniqueactuelle. À cet effet, des galeries de contrôle étaient creusés, voiles d'étanchéité avec des drains àla face aval et tirants précontraints permanents étaient fabriqués. Dans tous les trois cas, tenantcompte des opérations de remise en état, la stabilité de la barrage pouvait être prouvée à partir decalculs selon la méthode des éléments finis.

Jan 1, 2003

By D. Lunt

This paper describes and sets in context the commercially proven uranium extraction processes. It also discusses some of the technologies that are currently being pursued with the aim of reducing costs and overcoming a number of technical issues that are faced by process designers and operators. In doing so, opportunities for the transfer of extraction technology from other industries/commodities are identified. The key processing areas that are examined include: ?The influence of mineralogy. The type of uranium mineralization and the nature of its association within a particular deposit will have a major impact on process route selection. Uranium minerals are classified according to their influence on extractive metallurgy. As the uranium price has risen in recent times, so opportunities are increasing for the recovery of uranium from less conventional resources such as phosphates and fossil fuels. ?The opportunities for employing techniques aimed at reducing the capital and operating costs of the overall process such as heap leach and beneficiation. Preconcentration by screening, gravity separation and radiometric sorting can potentially reduce the mass flow to the downstream leach and recovery plants. ?Purification or separation of uranium in carbonate systems. While it is possible to directly precipitate uranium from clarified leachate, the presence of impurities such as vanadium, molybdenum and others may dictate that ion exchange or selective precipitation is employed. Advances have been made in other industries in terms of improved ion exchange equipment aimed at reducing resin inventories and hence costs. ?Separation in acid leach systems. Earlier developments included the use of combined SX-IX systems (Eluex or Bufflex) and the introduction of continuous countercurrention exchange (CCIX). Column SX has found a ready application to uranium in view of the rapid extraction kinetics. With the renewed interest in uranium processing, efforts are being redirected towards further development of resin-in-pulp (RIP) as a means of driving down capital and operating costs. ?Extraction in a chloride environment. Australia and Namibia are desert countries where good quality water comes at a cost. However, both have access to saline water from either the ocean or subterranean aquifers. The issues associated with operating a uranium extraction operation in such environments is discussed. ?Extraction from less conventional sources. Recent price increases for U3O8 have resulted in a number of companies examining the recovery of uranium from sources such as fossil fuels and phosphate deposits. Both of these areas were examined in the 1970s and 1980s and a number of approaches were commercialized. The paper reviews the extraction options.

Jan 1, 2007

By M. A. Ford

This paper reviews the history, sources, mineralogy, extraction metallurgy, conversion, and enrichment of uranium in South Africa. Over the past 40 years extraction plants were built at 27 sites, an9.over 140 kt of uranium have been produced. Older plants have had to adapt to changing market conditions, no single technology has had the opportunity to become entrenched, and costs have been reduced to a third of those of the original flowsheet. The research efforts aimed at developing the country s nuclear raw materials have been particularly rewarding, as they have enabled South Africa to become a world leader in the extraction of uranium from low-grade ores and to develop methods for uranium enrichment and the production of nuclear fuels.

Jan 1, 1993

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

By N. C. J. Dempers, J. A. L. Parker, R. A. Wildenboer

More than half of global cobalt reserves are located in the Southern African Copperbelt, stretching over the northern tip of Zambia and southern area of the Democratic Republic of Congo. In these areas, cobalt is not typically produced as a primary product but as a byproduct of copper production. Ores from this region often contain uranium, which is readily leached under typical copper leach conditions and enters the process. Uranium does not pose a challenge to copper production, but it becomes a significant problem when it follows cobalt to the cobalt precipitation process and results in unacceptably high levels of U in the final Co product. This paper evaluates the existing process technologies that can be used to remove uranium from cobalt-bearing process streams, including phosphate precipitation and ion exchange. Advantages and disadvantages of the uranium removal processes are discussed, and important design considerations are highlighted.

Jan 1, 2023

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that contains between 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By K. J. Oliver, A. G. Meyers, S. P. Hunt

Deformation Rate Analysis (DRA) and porosimetry have been used to demonstrate the “stress memory” effect in rock and to estimate the vertical in-situ stress in samples of fine-coarse grained sandstone and carbonaceous mudstone. The results of this study indicate that the stresses predicted using both methods are similar to those determined from depth and density of the overburden rocks. The results confirmed that DRA was still applicable even when the core had been sampled 18 months prior to testing. Additionally, the DRA results were modelled using the software PFC2D. A uniaxial test was modelled using the same rock parameters as those observed for the actual core samples. This numerical technique can be used as an aid for DRA results analysis, and can also be used to predict the minimum stress level at which the DRA technique is applicable. The results confirm that any rock mechanics laboratory having standard test equipment could apply the DRA method combined with standard UCS testwork to determine the in-situ stress. Mit der Analyse der Deformationsrate (DRA) und der Anwendung der Porosimetrie wird der Spannungsgedaechtnisseffekts (Stress Memory Effect) im Fels demonstriert, und es werden Abschaetzungen fuer die vertikale in-situ Spannung einer Probe aus mittelgrobem Sandstein und carbonierten Lehmstein getroffen. Die Ergebnisse dieser Untersuchung zeigen, dass die mit Hilfe dieser beiden Methoden ermittelten Spannungen sind vergleichbar. Die Ergebnisse bestaetigen, dass DRA noch anwendbar ist, wenn die Proben schon 18 Monate vor Untersuchungsbeginn gesammelt worden sind. Darueber hinaus wurden die DRA Ergebnisse mit Hilfe des Sofwarepakets PFC modelliert. Ein einaxialer Test wurde mit genau die gleichen Felsparametern, die fuer die eigentliche Probe gelten, modelliert. Diese numerische Methode kann sowohl als eine Unterstuetzung fuer DRA Ergebnisanalyse als auch zur Ermittlung der minimalen Spannung, bei dem die DRA Methode noch anwendbar ist, herangezogen werden. Die Ergebnisse bestaetigen, dass jedes Felsmechaniklabor, das mit den ueblichen Testgeraeten ausgestattet ist, die DRA Methode in Kombination mit dem Standard UCS Testarbeit zur Bestimmung der in-situ Spannungen anwenden kann. L'Analyse du Taux de la difformité (DRA) et les porosimetry ont été utilisés démontrer le " effet de la mémoire " du stress dans roc et estimer le stress dans - situ vertical dans échantillons de grès du grained fin grossier et mudstone carbonifère. Les résultats de cette étude indiquent que les insistances ont prédit utiliser les deux methods est semblable à ceux déterminés de profondeur et densité du surchargez des rocs. Les résultats ont confirmé ce DRA était encore même applicable quand le coeur avait été goûté 18 mois avant tester. En outre, les résultats DRA étaient des modelled qui utilisent le logiciel PFC2D. Une épreuve de l'uniaxial était modelled qui utilise les mêmes paramètres du roc comme ceux observé pour les réels échantillons du coeur. Cette technique numérique peut être utilisée comme une aide pour DRA résulte analyse, et peut aussi être utilisé pour prédire le niveau du stress minimum à que la technique DRA est applicable. Les résultats confirment que tout laboratoire des mécaniques du roc qui a le matériel de l'épreuve standard pourrait appliquer la méthode DRA combinée avec testwork UCS standard pour déterminer le stress dans - situ.

Jan 1, 2003

By H. Brüggemann

The exploration of deposits generates geological data which are suitable for creating a preliminary tectonic and stratigraphic model. Linked with the topographical map and analysis data from exploration drillings, this information forms a numeric representation of the deposit. The following example demonstrates an expert system which connects chemical quality requirements and quarrying criteria, and develops a quarrying strategy based on the calculated model. Additional constraining factors like process technology, quarrying methods, landscape protection regulations, etc. are included. The goal is to guarantee a long-term, homogeneous material flow from the quarry at acceptable production costs - even in the case of an extraordinarily inhomogeneous deposit. In order to fulfil this requirement it is necessary to consider a large number of rules, criteria and instructions which can be structured as an expert system and programmed with LISP at a comparably low cost. The chosen strategy is not necessarily final, but can be changed any time by altering or varying the framework of conditions. The output consists of a block-working sequence which best satisfies the set requirements for appropriate points of quarry opening.

Jan 1, 1987

By Y. Jeong, K. Kim

Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of ‘what if’ studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.

Dec 13, 2023

By M. H. Moys

A method of estimating the percent solids in the discharge from a grinding mill is described and tested on both pilot and industrial scale. It involves the use of energy and mass balances around the mill discharge sump, requiring measurements of the flowrate and density from the sump together with temperatures of all streams flowing to and from the sump. Accurate estimates of the dynamic variation of mill discharge percent solids are made available, provided that occasional manual sampling of the stream is done to cope with drift in instrumentation. The use of a computer in this application was essential; the various advantages associated with its use are discussed. It is anticipated that this estimate of discharge density can be controlled at a set point by manipulation of the water fed to the mill, resulting in significant decreases in specific power consumption and media consumption.

Jan 1, 1987

By P. Kitobo, T. Nduba, D. Mbay, J. B. Vangu, R. Ciband

The flotation plant tailings at Kamoa Copper Mine concentrator were found to contain a high proportion of extremely fine particles. The potential issues with settling these fine solids were resolved by the use of a poly-di-allyl-di-methyl ammonium chloride (DADMAC) coagulant, Flobead DB 45 VHM, in conjunction with a standard anionic polyacrylamide flocculant. This paper outlines some of the issues encountered and how they were resolved at the Kamoa concentrator. The potential to use this process and technology at other sites is also considered

Jan 1, 2023

By M. Tangstad, B. Monsen, H. Midtgaard

The increased attention towards reducing emissions of fossil CO2 due to its potential global warming effect has resulted in a focus on renewable resources, as charcoal. Since charcoal is produced from growing wood it does not contribute to global warming. This paper gives a brief review of consequences of and reasons for using charcoal in the silicomanganese (SiMn) production. Results are presented from practical SiMn smelting experiments, on a pilot scale, using charcoal as reduction material and comparing with coke. As slag- and CO2-reactivity are important for furnace performance these features have also been measured.

Jan 1, 2004

By Chandrakala Kari, S. Mohan Rao, Gajanan Kapure, K. S. Raju

High carbon ferrochrome production process is energy intensive, consumes approximately 3300-3400 kWh per ton of metal produced. This amounts to ~ 34% of the total ferrochrome production cost. The power costs in India are almost 4 times greater than the leading ferrochrome producing countries like South Africa. Hence there is a need to look for alternative sources of energy. In ferrochrome making process large volumes of high concentration CO gas (~ 85%V) is developed at ~400-5000C, which if combusted within furnace represents high potential for significant electrical energy savings. In a typical heat in the state-of-the-art submerged arc furnace, about 34 kmol of CO gas is generated per ton of ferrochrome metal, which, if post combusted to CO2, represents 7620 MJ of energy. Post combustion of the evolving CO (and H2) gas to CO2 can be achieved by providing additional oxygen before the generated CO gas leaves the furnace. In this paper, a concept of post combustion in submerged arc furnace as potential source of significant electrical energy saving in ferro-chrome making process has been explored. The prospects and limitations of the same are discussed. The value of this paper lies in its attempt to explore the post combustion application to submerged arc furnace with an objective of significant reduction in electrical energy consumption in ferrochrome production process.

Jan 1, 2007

By M. Tangstad, H. Brun, P. Calvert, A. G. Lindseth

In 1999, Eramet bought the ferromanganese plants in Porsgrunn and Sauda (Norway) and Marietta (USA). With an ownership in the Comilog mine, the plants will operate with a high amount of Comilog ore. The properties of Comilog ore are reviewed and compared to a number of industrial operations. Important ore properties are chemical and mineralogical analyses, CO reactivity and mechanical strength. The advantage of Comilog ore is its contribution to lower energy and coke consumption. However, special precautions must be taken regarding the amount of fines and water introduced in the furnace, as Comilog ore is more porous compared to other Mn ores.

Jan 1, 2004

By R. B. Khumalo, F. K. Mulenga

Sampling in a continuous flotation plant is always a challenge as these plants are meant for production and not research work. The continuous flotation operation used in this work produced three sets of data: the first was based on overall plant performance, done by sampling the feed, concentrate, and tails; the second was based on the roughers row cell-by-cell; the third set of results came from the cleaners/recleaners row cell-by-cell. The highest recovery results in all sets of data obtained lie in the particle size ranges of 40 μm and 100 μm, which is in agreement with results by other researchers in the same field. King’s theoretical (model) recovery proved to be able to fit the experimental data but there is still room for improvement as the sum of squared error ranged between 400– 1200. Data obtained in continuous flotation operation could be used with batch flotation test-work to characterize scale-up of flotation cells.

Jan 1, 2023

By J. M. McKinley

Mineral exploration programmes around the world use data from remote sensing, geophysics, and direct sampling. On a regional scale, the combination of airborne geophysics and ground-based geochemical sampling can aid geological mapping and mineral exploration. Since airborne geophysical and traditional soil-sampling data are generated at different spatial resolutions, they are not immediately comparable due to their different sampling density. Several geostatistical techniques, including indicator cokriging and collocated cokriging, can be used to integrate different types of data into a geostatistical model. However, with increasing numbers of variables the inference of the crosscovariance model required for cokriging can be demanding in terms of effort and computational time. In this paper a Gaussian-based Bayesian updating approach is applied to integrate airborne radiometric data and ground-sampled geochemical soil data to maximize information generated from the soil survey, enabling more accurate geological interpretation for the exploration and development of natural resources. The Bayesian updating technique decomposes the collocated estimate into two models: prior and likelihood models. The prior model is built from primary information and the likelihood model is built from secondary information. The prior model is then updated with the likelihood model to build the final model. The approach allows multiple secondary variables to be simultaneously integrated into the mapping of the primary variable. The Bayesian updating approach is demonstrated using a case study from Northern Ireland. The geostatistical technique was used to improve the resolution of soil geochemistry, at a density of one sample per 2 km2, by integrating more closely measured airborne geophysical data from the GSNI Tellus Survey, measured over a footprint of 65 x 200 m. The directly measured geochemistry data were considered as primary data and the airborne radiometric data were used as secondary data. The approach produced more detailed updated maps and in particular enhanced information on the mapped distributions of zinc, copper, and lead. The enhanced delineation of an elongated northwest/southeast trending zone in the updated maps strengthened the potential for discovering stratabound base metal deposits..

Jan 1, 2014