Search Documents

By G. T. C. Emere, E. C. Hunter

The use of cylindro-conical settlers for the clarification of underground water by E. C. HUNTER- (Associate) G. T. C. EMERE-, B.A. (Hons.) (Keele) (Visitor) This paper analyses the performance of conical settlers on Harmony Gold Mine from 1959 to the present time, and describes the investigation that was undertaken to substantiate and improve the use of conical settlers for a new pump chamber in another part of the mine.

Jan 5, 1977

By Ronald J. Roman

All mining and milling complexes can, within limits, operate at a variety of production rates. Factors of economic importance that are affected by production rates are costs per unit production, recovery and product grade. Once the relationship between the production rate and cost is established, dynamic programming techniques can be used to define the optimum production schedule (that is, the production schedule that maximizes the present worth of the operation) for the life of the deposit. In general, assuming that the capacity and efficiency of the physical plant remain unchanged throughout the life of the deposit, the optimum production rate is not constant for the life of the deposit, but declines gradually as the deposit is being exhausted.

Jan 1, 2014

By A. Hinde, M. H. Moys

Tailings from metallurgical plants, when deslimed with hydrocyclones, provide a valuable source of material for the backfilling of mines. The effectiveness of this material as a support medium is a sensitive function of its particle- size distribution and water content. It is therefore important that the hydrocyclone-classification plants used to prepare the backfill are operated efficiently, and that the effects of feed disturbances on the composition of the backfil are minimized. This paper addresses the problem of the design, control, and optimization of classification plants to satisfy this need. The development of a computer program to simulate the dynamic behaviour of a hydrocyclone circuit of any given configuration is described. The use of the simulator to investigate the relative performance of conventional and innovative control strategies for single-stage and two-stage circuits is discussed in depth. The results of simulation studies are presented that indicate there is considerable scope for improving the performance and cost-effectiveness of backfill-classification plants.

Jan 1, 1991

By L. Andrews

Electron microbeam analysis of metallurgical samples covers abroad field and has applications in the areas of minerals processing, hydrometallurgy, pyrometallurgy, physical metallurgy and corrosion. Some idea of the possibilities of microbeam techniques can be illustrated by examining the following example of a run of mine gold ore sample. Milling and bulk chemical analysis of the ore will provide major and minor element analysis as well as the gold grade. More detailed chemistry can also reveal the presence of trace elements that may be advantageous or deleterious to downstream processing. Electron microbeam analysis can provide additional information in the form of size, liberation, association and composition of the gold, the percentage of refractory gold, the size, liberation, association and composition of enclosing sulphide or arsenide phases and the levels and association of the trace elements that may affect processing. In most cases electron microbeam analysis complements bulk chemistry, and does not replace it. Both techniques should be used in parallel for maximum effect. This paper touches on the origin and history of electron microbeam techniques, as well as the theory behind microbeam analysis and processing. The more common types of instruments and their applications will also be dealt with briefly.

Jan 1, 2007

By Lesley Andrews

"Electron microbeam analysis of metallurgical samples covers a broad field and has applications in the areas of minerals processing, hydrometallurgy, pyrometallurgy, physical metallurgy and corrosion.Some idea of the possibilities of microbeam techniques can be illustrated by examining the following example of a run of mine gold ore sample. Milling and bulk chemical analysis of the ore will provide major and minor element analysis as well as the gold grade. More detailed chemistlY can also reveal the presence of trace elements that may be advantageous or deleterious to downstream processing. Electron microbeam analysis can provide additional information in the form of - size, liberation, association and composition of the gold, the percentage of refractory gold, the size, liberation, association and composition of enclosing sulphide or arsenide phases and the levels and association of the trace elements that may affect processing. In most cases electron microbeam analysis compliments bulk chemistry, and does not replace it. Both techniques should be used in parallel for maximum effect.This paper touches on the origin and history of electron microbeam techniques, as well as the theory behind microbeam analysis and processing. The more common types of instruments and their applications will also be dealt with briefly - more details on, and examples of, the applications and choice of technique will be covered in the presentation.Mosely first discovered, in 1913, that the frequency of emitted X-radiation excited by an electron beam is a function of the atomic number of the analysed element. This discovery led to the development of spectrochemical analysis. The forerunners of the electron microanalysers of today, however, were only invented during the nineteen fifties. The electron microprobe was developed in parallel by Castaing and Guinier in France and by Borovski in Russia, but Castaing's design was the basis of modern microanalysers. The initial area of analysis was brought down from over 1 mm2 to less than 2 µm, as it is today. In 1956 Cosslett and Duncumb invented the scanning electron microprobe, where a beam of electrons could be scanned across an area of a sample. This, in turn, led to the development of the electron microprobe with both scanning and point analysis capabilities that we know today.Essentially, all electron microbeam instruments operate by the production of a beam of electrons from a filament in a vacuum (i.e. an electron gun). The electron beam leaves the gun and is accelerated and focused by a series of electromagnetic lenses while passing down an evacuated column. The electrons eventually strike the surface of the sample to be analysed and may travel through a thin sample (transmitted electron microscopy) or react with a thicker sample to produce several reflected kinds of radiation."

Jan 1, 2014

By N. C. Joughin, A. C. Buckmaster

The use of face conveyors in gold mines by N. C. JOUGHIN. B.Sc. (Eng.). Ph.D. (Wits) (Member) and A. C. BUCKMASTER; M.A. (Cantab.) A mechanized stope-cleaning system has been developed around an armoured face conveyor, which was tested on the surface and in two underground trials. In the second underground trial, an average face advance of 8,5 m per month was obtained with a labour productivity of 27 ca/worker/month on a two-shift blast cycle. Two new face cleaning systems have been built, each incorporating an armoured face conveyor, a loading plough, a collapsible self-advancing barricade, and an integral roof-support system. These are about to be tested. A new type of reciprocating flight conveyor is being developed for stope use. This is cheaper, lighter, and more compact, and exhibits better wear characteristics, than an armoured face conveyor. In the early stages of the trials, this conveyor frequently achieved a singleshift blast cycle. It should be possible to achieve face advances of up to 40 ca/worker/month with a consistent one-shift blast cycle. The use of drill rigs and a self-advancing roof-support system would improve the productivity to over 50 ca/worker/month.

Jan 2, 1976

By E. Bakhtavar, R. Mikaeil, D. Khademi

"Fuzzy-weighted integer goal programming has been developed and used to select the most suitable site to construct a central processing plant for several adjacent small-scale dimension stone quarries, based on the most effective criteria. In the first step of mathematical modelling, the most important goals and decision variables were defined. Accordingly, an objective function was used in the model for minimizing the sum of undesired fuzzy-weighted deviations. Fuzzy weights were determined by a matrix of pairwise comparisons of various expert judgments in this field and the fuzzy geometric mean. The goal and systemic constraints were also modelled. The most suitable site for the construction of the plant was selected after solving the mathematical model in the ExcelR Solver add-in. The selected site had various advantages over the other sites, such as the shortest average distance to the quarries, the shortest distance to power access and workforce, and the lowest land price. IntroductionSelection of the most suitable site of a plant is one of the most important considerations when constructing an industrial project. A suitable site has a significant effect on a company's competitiveness in the market. Selecting a desirable location for constructing plants such as mineral processing facilities is an essential part of the economic planning that will enable a company to meet the needs of related upstream and downstream operations. These units are considered to be best built near the relevant mining sites because of technical difficulties, the cost of transporting minerals, and the traffic hazard caused by the movement of trucks transporting materials. Two main types of research using multiattribute decision-making models have been reported for selection of a processing plant site (Safari et al. 2010, 2012). In that research, the analytic hierarchy process (AHP) and fuzzy technique for order preference by similarity to ideal solution (TOPSIS) approach were applied to select the suitable locations for the mineral processing plants for phases 1 and 2 of Sangan iron ore mine."

Jan 1, 2017

By S. J. C. L. Peeters

Geographical information systems (GISs) provide sophisticated functionalities t1tat can be used by the personnel in many aspects of the mining industry to visualize, analyse, and manipulate spatial and tabular data. This paper presents an experimental case study for Hartebeestfontein Gold Mine. It shows how data from different computer systems can be brought together into a GIS by use of the Arc/Info and ArcView programs.

Jan 1, 1996

By J. Svoboda, W. J. C. Venter, R. N. Guest

The use of gravity or magnetic separation followed by upgrading on a shaking table recovered about 25 per cent of the copper and lead minerals, at a combined metal grade of 20 per cent, from the final flotation tailing at the Tsumeb Mine. Magnetic separation recovered the copper minerals more efficiently than the lead minerals; it also recovered finer particles more efficiently than standard gravity separators. However, the grade of the concentrate produced by magnetic separation was not of sufficiently high grade, and further upgrading by gravity separation was necessary. It was decided to install an 'all-gravity' plant, which would have the added advantage of acting as a monitor or 'policeman' on a plant that receives a fairly variable feed.

Jan 1, 1988

By H. C. Voges

The use of heavy-medium separation in the processing of iron ores by H. C. VOGES. B.Sc. (Visitor) The paper discusses various aspects of the application of heavy-medium separation to the processing of hematite ore at Sishen and Thabazimbi. The two main factors to be borne in mind in the design of a plant for such beneficiation are the Iow unit value of the iron ore produced and the high separation densities required. The four factors of importance in the avoidance of high viscosity in the ferrosilicon medium are discussed in turn.

Jan 6, 1975

This paper examines the new water-hydraulic (hydropowered) drill rigs that have been developed and proven in the last decade primarily in tabular, shallow-dipping, narrow-reef hard-rock South African mines. These include drill rigs for flat-end tunnel development, narrow inclined raises and winzes, large inclines and declines and longhole-based developments such as ore passes and vent raises. The hydropower technology rigs offer advantages both in safety and performance over traditional compressed-air-powered, hand-held development, and are generally more cost-effective than imported oil electro-hydraulic drill rigs. Furthermore, hydropowered rigs are inherently energy-efficient. The benefits of hydropower are discussed and a ?comprehensive development model? is presented which demonstrates that ore-bodies can be accessed in significantly shorter times. ?Localized? half level hydropower systems are introduced and a range of ancillary equipment available is listed.

Jan 1, 2012

By J. Searra, M. Aboagye

"For new mining projects or for medium- to long-term areas of existing mines, drilling data is invariably on a relatively large grid. Direct estimates for selective mining units (SMUs), and also for much larger block units, will then be smoothed due to the information effects and the high error variance.The difficulty is that ultimately, during mining, selection will be done on the basis of SMUs on the final close-spaced data grid (grade control), which will then be available, i.e. the actual selection will be more efficient, with fewer misclassifications. However, this ultimate mining position is unknown at the project feasibility stage and therefore has to be estimated. This estimation is required because any cash flow calculations made on the basis of the smoothed estimates will obviously misrepresent the overall economic value of the project, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the average grade of the orebody. Similarly, unsmoothed estimates will be conditionally biased and will give even worse results, particularly in local areas of short- and medium-term planning or mining.This paper presents a case study of indirect post-processing and proportional modelling of recoverable resources designed for mediumand long-term mine planning at the Gold Fields’ Tarkwa Mine in Ghana. The case study compares long-term indirect recoverable mineral resource estimates based on typical widely spaced feasibility data to the corresponding production grade control model as well as the mine production. The paper also proposes certain critical regression slope and kriging efficiency control limits to avoid inefficient medium- to longterm recoverable estimates, and highlights the danger of accepting block estimates that have a slope of regression less than 0.5."

Jan 1, 2015

By J. van Zyl Visser

The advancement in Information Technology has resulted in a change in workflow practice in our Mineral Resource Management (MRM) offices on the mines and at our corporate office. This paper discusses the AngloGold approach in defining an IT strategy for MRM, a brief overview of systems usage and benefits. AngloGold has gone through a transformation phase and has positioned itself as a world-class, low cost producer. To support this objective, an initiative has been launched to provide the MRM division with an integrated MRM technical suite of systems with support of a Management Information System. Technical systems for a tabular orebody are not freely available and hence it took AngloGold almost seven years and a significant amount of capital to develop an integrated suite of technical systems. AngloGold MRM IT adopted the typical Zachman framework (value chain) approach in the analysis process and formulated the final deliverable in terms of AngloGold’s strategy. Major benefits have been realized through the ability to change planning scenarios in a short period of time and hence be able to increase reserves and NPV. The development of MRIS, which will become the flagship in AngloGold’s portfolio of systems is in phase two and this system will allow AngloGold to publish Resources and Reserves as per SAMREC and the JORC Code at will. The availability of information at all levels of the operations has made making decisions easier and hence some specialized reports such as the Basic Mining Equation were developed from the Corporate Data warehouse and from the MRM reporting database. Decision Support Systems(DSS) such as Business Objects and Oracle Express are now being used to assist in the process. The decision to use Business Objects to replace SAS reporting as the core reporting tool has resulted in the empowerment of the user and major cost saving as far as the use of consultants to set up standard reports.

Jan 1, 2003

By O. Korhonen, T. Leskinen

The use of large OK-16 flotation machines at the concentrators of Outokumpu Oy by o. KORHONEN and T. LESKINEN(Visitors) The development ofthe OK-16 flotation machine is described briefly, and an account is given of its use at various concentration plants in Finland. The benefits arising from the use of larger flotation machines are listed, and the technical specification of the OK-16 machine is detailed in an appendix.

Jan 6, 1976

By E. J. Magri, R. M. Murray

This paper describes the application of linear programming to the monthly 'set up' planning of stopers' sections on two gold mines. On one of these mines, the purpose of the exercise was to maximize the total stoping production (measured in centares per month). On the other mine, the maximum stoping contribution (rands per month) was required. Maximization was to be achieved through improved planning, independently of the various other productivity improving activities that were taking place at the same time. The results to date show that, when linear programming is used, an average increase of about 9 per cent in stoping production (or contribution) can be obtained for these two mines.

Jan 1, 1978

By Stafford McKnight, Larissa Koroznikova, Steve Hall, Cameron Klutke

This paper outlines a simple methodology for mineral characterisation, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterisation of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilised at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used, however this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900?s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterisation of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4 ? 4.7 and zircon RD 4.6 ? 4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150 microns). The developing methodology that can achieve low-cost, low toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

By C. Klutke

This paper outlines a simple methodology for mineral characterization, developed as part of the Australian Mineral Industry Research Association (AMIRA) managed research project P777 ?The Development of Heavy Suspension Techniques for High Density Separations (Replacement of Clerici?s Solution)?. The project was sponsored by De Beers, Rio Tinto and Iluka Resources. Heavy mineral characterization of samples arising from exploration, mining or metallurgical processes is frequently conducted using laboratory heavy liquid analysis. Unfortunately, there are only a limited number of high density (?heavy?) liquids and these tend to be more toxic as their density increases. Low-toxicity inorganic solutions, based on tungsten compounds, have been developed that can be utilized at relative densities (RD) up to 3.0. Beyond this value organic liquids can be used; however, this presents significant health and safety hazards. Diiodomethane (methylene iodide) having a relative density of 3.31 is commonly used. Mixtures of thallium formate and thallium malonate were found in the early 1900s by Clerici to provide liquids having specific gravities between 4.0 and 5.0. For the characterization of the heavy components of mineral sand deposits (e.g. anatase RD 3.9, rutile RD 4.2, ilmenite RD 4.4?4.7 and zircon RD4.6?4.8) there is currently no heavy liquid alternative to Clerici?s solution. Clerici?s solution is highly toxic and testing is now conducted by few laboratories worldwide, with costs reflecting the chemical costs, infrastructure costs and health and safety regimes (e.g. blood testing of exposed staff). A simple laboratory technique of density fractionation has been developed, employing suspensions of fine tungsten carbide particles in lithium heteropolytungstates solutions, that can replace Clerici?s solution in the evaluation of fine mineral sands samples (e.g. -250 +150microns). The developing methodology that can achieve low-cost, low-toxic separations at relative densities above 4.0 is outlined and the comparison of results with Clerici?s solution presented. In addition, preliminary work on density fractionation of zircon samples is presented. Zircon fractionation relates to their inclusion, radionuclide content and metamictization.

Jan 1, 2007

By A. Hinde, M. Moys, L. C. Woollacott

The material-balance smoothing technique is applied directly to the problems associated with the evaluation of the performance of backfill-preparation plants. A computer package specially designed to assist the process engineer in such evaluations has been developed. The usefulness of the technique as compared with other methods for the extraction of meaningful information from backfill-plant data is demonstrated.

Jan 1, 1992

By G. van Hout, D. Rahal

Caving is a mass mining method that is normally applied to large, low grade orebodies because of its low production cost and high capacity. However, equipment breakdown and poor draw management can cause mining costs to exceed that of all other mining methods. One way to minimize the effect of disruptions in the mining cycle is to use Mixed Integer Linear Programming (MILP) for long-term scheduling. This paper describes a MILP goal program which has the dual objectives of minimizing deviation from the ideal draw profile while achieving a production target. Schedule optimization is performed using a life of mine approach in which all production periods are optimized simultaneously. The underlying assumption being that material mixing in the short-term (between monthly optimization cycles) has a minimal effect on the long-term state of the panel. Schedule optimization is carried out using six general constraint types to model and control production. The constraint types define: deviation from ideal practice, panel state, material flow conservation, production quality, material flow capacity and production control. These constraints define production targets and drive production toward the ideal profile while maintaining correct mining practice. Application of the model using production scheduling data for a De Beers kimberlite mine. It is shown how different production control constraints regulate production from individual drawpoints as well as recovery of the ideal panel profile by implementing an optimised draw schedule.

Jan 1, 2003

By T. N. Moore, E. M. De Souza

This paper details a study conducted in Canada on the use of a drill with two different types of elastomer-covered handles in place of the standard steel handles. One type of handle was covered with a relatively stiff elastomer with a durometer of 70 (referred to as the plastic handle), and the other was covered with a more compliant elastomer with a durometer of 56 (refered to as the rubber handle). It was found that, compared with the steel handle, the overall acceleration at the interface between the plastic handle and the drill operator's hand was 2,5 times less, and that between the rubber handle and his hand was 3 times less. This reduction occurred predominantly in the frequency range above 500 Hz, and was greater with increasing frequency. However, an analysis based on the methodology of an international standard (which places greater importance on low-frequency vibration), indicated that the reduction in vibration levels was minimal. ~he driller himself felt that operation with the plastic and rubber handles was more comfortable, the rubber handle being preferred.

Jan 1, 1991