Search Documents

By H. Henao, E. Kohnenkamp, L. Rojas

The slags generated in the copper conversion process are mainly composed of Cu2O-Fe2O3-SiO2 with the compounds CaO and Al2O3 in concentrations up to 10 wt%. The present work contributes to the knowledge of the conversion process, generating experimental data for the diagrams of phases Cu2O-Fe2O3- SiO2-Al2O3 and Cu2O-Fe2O3-SiO2-CaO. The experiments were carried out in a tubular furnace at temperatures of 1150°C and 1200°C under a condition of saturation with tridymite. Once the equilibrium was reached, the samples were fast quenched in water. The phases in the samples were observed in a Scanning Electron Microscope (SEM) and the elemental composition of the phases analyzed by means of Energy-dispersive X-ray spectroscopy (EDS) detectors. The addition of Al2O3 and CaO into the Cu2O-Fe2O3- SiO2 system resulted in an appreciable displacement of the liquidus lines, corresponding to an expansion of the liquid in the tridymite primary phase field. INTRODUCTION The conversion process of copper consists of oxidizing Fe and S present in mattes with 60 to 65wt% Cu (up to 16wt% Fe). This process is separated into two stages: 1- Slag blowing: Fe is oxidized, the addition of a flux such as SiO2 (silica) forms a second liquid phase called slag, this phase is removed from the furnace; 2-Copper blowing: in this stage, the matte with low concentration of Fe (<1% w/w) is again oxidized to remove S as SO2 in the exhaust gases. The product of these two processes is the formation of Copper Blister (> 98wt% Cu) (Schlesinger et al., 2011). Unlike the aforementioned conventional processes, in most Chilean smelters, conversion Peirce- Smith Furnaces are loaded with high copper matte (70–75wt% Cu) (Henao & Moyano, 2016). Due to the low concentration of iron in these matte (up to 5wt%), it is considered that separating the conversion process in two stages is neither operational nor environmentally convenient. Therefore, the process is carried out in a single stage (Pradena et al., 2006), generating a slag phase with a high percentage of Cu2O (wt%Cu>40).

Jan 1, 2019

By Earl Gebhardt

"The planning and design of mining panels in the Potash Corporation of Saskatchewan Inc., Lanigan Division mine Block B involved a number of investigative techniques. The techniques utilized to gain insight into the viability of mining included2-D and 3-D seismic surveys, longhole drilling, exploration wells, photo lineament, magnetic and gravity surveys, and actual room excavation.IntroductionPotash Corporation of Saskatchewan Inc. (PCS) owns and operates four potash mines in the province of Saskatchewan. The Lanigan Division mine is located 110 Ian east of Saskatoon, Saskatchewan, near the town of Lanigan.The Lanigan Mine commenced production in August 1968under the ownership or Alwinsal Potash of Canada Limited. The mine was purchased by PCS in 1977.Lanigan Division&apos;s productive capacity is 3.4 million tonnes of product per year. Ore is extracted from the "" B"" zone or Layer III or the Patience Lake member of the Prairie Evaporite, more than 1000m below surface . The Patience Lake member (approximately 20 m thick) consists of potash interbedded with salt. The average run-of-mine ore grade is 21070 K20 (Fig. I).The mine was initially developed using the room-and-pillar technique. Improvements in mining resulted in the use or extensible conveyors in long panel rooms."

Jan 1, 1993

By I. S. Thompson

A program of geochemical till prospecting, carried out by Derry, Michener & Booth in 1974, was instrumental in t~ e discovery of a copper deposit in Currie Township, Ontario, beneath thick lacustrine deposits of the Abitibi Clay Belt. The prospecting system involved the continuous collection of glacial sands and gravels beneath the clays, using a track-mounted, dual-tube rotary drill, and the separation and geochemical analysis of the heavy mineral content for Cu, Zn, Pb, Ag and Au. In one of 22 holes drilled down-ice from nine Canadian Nickel airborne EM conductors, fragments of chalcopyrite-bearing graphitic argillite, assaying 12% Cu, were recovered from a 14-foot gravel section beneath 83 feet of clay. Ultimately, mineralization was identified in 10 of 11 additional holes drilled up to 3,000 feet down-ice from the Currie deposit. The glacial fan, when compared to the 1,200- by 165-ft area of the subcropping mineralization, is at least 20 times the area of the deposit and is the result of glacio-fluvial reworking of the mineralized ground moraine. The Currie deposit is contained within a Keewatin succession of graphitic argillite, dacite tuff and graywacke, which is intruded by dacite and feldspar porphyry sills and dykes and truncated by a Keweenawan diabase dyke. Grade and thickness of the mineralization, which lies chiefly within the argillite, is related to felsic intrusives and hydrothermal alteration, and to fold hinges.

Jan 1, 1979

By Jean A. Bastien

Cette présentation décrit les étapes de développement et l?exploitation souterraine au puits Penna chez Agnico-Eagle division Laronde. Les sujets suivants sont touchés : le fonçage du puits, le développement des niveaux, la méthode d?exploitation, la manutention de la roche brisée, le méthode de remblayage et la ventilation. En résumé : le fonçage du puits s?est fait sur 2,240 mètres de novembre 1995 à mars 2000. Le développement des niveaux a débuté en octobre 1998. Les opérations de minage ont débutés en août 99 dans le premier horizon situé au dessus du niveau 122. Les chantiers sont exploités par longs-trous d?environ 25 mètres de long avec un diamètre de 10 cm. Les accès à la zone minéralisée sont transverses. Le minerai est soutiré des chantiers et acheminé au passe-minerai a l?aide de chargeuses navettes. Par la suite, le minerai passe sur un marteau, est concassé et transporté sur un convoyeur, jusqu?au silo de 4,500 tonnes au-dessus de la station de chargement automatisée du niveau 152 d?ou les skips sont alimentés. Le remblai en pâte est envoyé de la surface par des trous ayant un revêtement d?acier. Le diamètre intérieur est de 15 cm. Le réseau de ventilation est principalement alimentée par des ventilateurs de surface (système aspirant et souflant) conçus pour acheminer sous-terre un maximum de 640 mètres cubes par minutes (1,350,000 pcm).

May 1, 2001

By A. Villanueva

The effect of High Pressure Grinding Rolls (HPGR), as a preceding stage to a conventional ball mill circuit at PT Freeport Indonesia?s C1/C2 concentrators, has been studied in terms of downstream grinding efficiency and circuit performance. When milling the product from the HPGR, mill capacity increased by 21% for the same product grind size, when compared to processing similar ore from a conventional crushing circuit. This achievement is a result of several reasons, among them: reduction in feed size (F80), fines generation beyond the proportional reduction in F80, reduction in ore hardness induced by HPGR comminution mechanism, optimization of the recycle system of the HPGR and ball string optimization in the ball mill circuit given the new feed to the mill.

Jan 1, 2012

By M. Tanaka, H. Narita, T. Fuchikami, K. Morisaku, K. Nagao, T. Yoshida, K. Kuroda

The effect of various N-substituents on the performance of amide-containing tertiary amine compounds in the extraction of Rh(III) from HCl solutions was investigated to optimize the structure of these compounds for industrial use. It was found that N-2-ethylhexyl-bis(N-di-2-ethylhexyl-ethylamide)amine and tris(N-di-2-ethylhexyl-ethylamide)amine, which have long, branched alkyl chains, were suitable for Rh extraction, because they were soluble in a practical diluent (80 vol% n-dodecane?20 vol% 2-ethylhexanol) and stable against highly concentrated HCl/Rh solutions, and showed high selectivity for Rh(III) over Pd(II) and Pt(IV).

Jan 1, 2014

By D. L. Chen, Q. Zhang

The effect of particle sizes on the low cycle fatigue (LCF) life of discontinuously reinforced metal matrix composites (DR-MMCs) has been widely studied. However, how the particle size affects the LCF life of DR-MMCs quantitatively is still lacking. The aim of this investigation is, therefore, to present an analytical model linking the LCF life to the particle size. This model, based on the enhanced dislocation density in the matrix and the load bearing effect of particles, showed that a decreasing particle size results in a longer LCF life, and the results predicted are in good agreement with the experimental data.

Jan 1, 2004

By Ifeanyichukwu Nweke

"Aluminium rolling processing from ingots to cold rolled coils comes with a lot of challenges especially in controlling defective products in casting, hot mill and cold mill operations. Hence this study focused on reducing defects at mills and cast-house using six sigma approaches. The use of six sigma approach will help the production experts to determine the gap between its operation and world class process. Practical data from First Aluminium Rolling mills were presented and analysed and mini improvement projects were proposed based on organisation need to achieve excellence. This study encourages aluminium alloy industries to pursue process improvement projects on the basis of analysis on data obtained from their shop floor, hence ensuring that through this, recovery is improved and cost of poor quality is reduced.INTRODUCTION Engineer Bill Smith while working at Motorola in 1986 introduced a new concept in which a set of techniques and tools are used for process improvement by controlling variations (defects). These tools and techniques are explained by an acronym DMAIC. D DEFINE the problem M MEASURE the variables in the problem A ANALYSE the variables of the problem I IMPLEMENT and verify the solution to the problem C CONTROL the solution to sustain it Most times in six-sigma approach, variations in the process that results in defects and customers’ dissatisfaction are targeted at 3.4 defects per million opportunities. There are numerous methods six sigma application use to achieve quality results and innovative strategies. Improving the quality of process through these methods helps identify and reduce variations which paves way for organisational excellence. In this study, it is encouraged to use six sigma techniques to improve aluminium rolling operations and other aluminium processing activities, the benefits of such improvement concept include: • Satisfy the voice of the customer (VOC) • Minimise costs • Maximise Profits • Build Good Team • Implement Profitable Project"

Jan 1, 2018

By T. Nomura, N. Saitoh, K. Tamaoki, Y. Konishi

We have developed new recycling technologies, based upon an eco-friendly biotechnology, in order to extract precious and rare metals sourced from end-of-life products and electronics. We have been focusing on the metal ion-reducing bacteria, Shewanella algae and Shewanella oneidensis, that are able to reduce and deposit gold ions (Au(III)) or PGMs ions (Pd(II), Pt(IV) and Rh(III)) into metal nanoparticles at room temperature within 120 min. When processing the aqua regia leachate of printed circuit boards, Shewanella bacteria were able to rapidly and selectively collect gold ions under acidic conditions in the presence of heavy metal ions, proposing a new bio-recovery system for gold. This biotechnological procedure also has the potential to allow the recovery of PGMs from the leachate of automotive catalysts. Shewanella bacteria were also able to successfully perform the complete reduction and deposition of the PGM ions. The ability to collect the PGM ions suggests that this represents a new process for the biorecovery of PGMs from used automotive catalysts. Our proposed biological method enables the rapid and highly efficient recovery of precious and rare metals via separation and concentration utilizing microbial reactions at room temperature.

Jan 1, 2014

By Alfred W. G. Wilson

THE state of development of its iron and steel industries serves as a 1eading index to the general condition of a nation&apos;s business affairs. In this paper, the authors present an economic study of the progress of this group of industries in Canada for the decade 1927-1936. The statistical data and most of the tables which accompany this article have been com-piled by John Casey, Statistician, Bureau of Mines; the text and some of the computations have been prepared by the seni0r author. The principal source of statistical information has been the publications of the Dominion Bureau of Statistics; where other sources have been consulted, they are noted in the text. All weights are given in short tons. Records for the years 1913 and 1918 are also presented in the group of tables dealing with iron ore and pig iron; they will serve as a basis for comparison with nearly normal years in the two decades prior to 1927-36, which included the abnorma1 years of the Great War. GENERAL REVIEW At the beginning of the decade under review, this group of industries had returned to almost normal production, as determined by pre-war conditions. Iron ore consumption showed a steady increase between 1927 and 1930; a marked decline began in 1930 and reached its culmination in 1932, when the recorded consumption of ore was 293,353 to11s, about 16 per cent of the average consumption during the first four years of the decade; the last four years of the decade show a gradual increase in consumption; the amount of ore used in 1936 was still slightly below the amount used ten years before, in 1927 (see Table 1, top).

Jan 1, 1938

By C. A. Young, H-H. Huang, L. G. Twidwell

Equilibrium calculational software programs can be effectively utilized to model important parameters in aqueous and aqueous/solid systems, e.g., activity or concentration, solubility, temperature, solution pH, solution potential, and ligand complexation. In this regard, the calculational program ST ABCAL will be demonstrated. Illustrative examples for the creation of diagrams such as potential-pH, and activity or concentration-pH will be presented to demonstrate the fundamentals in real hydrometallurgical systems. Speciation, titration and mixing will be used to simulate or predict operational processes. Berkeley Pit water from a flooded abandoned copper open-pit mine will be used to illustrate the modeling process. According to analytical results the water contains about 20 important constituents. In addition to measured potential and dissolved oxygen, there are two distinctive oxidation/reduction couples. Concentration and other experimental parameters are seldom matched to each other and 12 different conditions have been identified. Water for each condition must be speciated in order to find the best-fit model. The STABCAL program will be used for the modeling calculations and the implication of the water chemistry to defining treatment opportunities will be discussed.

Jan 1, 2005

By M. Olper

Commercial copper plants utilising current best technology are tending towards ever increasing scale, the concentrate requirements of which cannot be serviced by a single mine. In such cases, raw materials are often sourced from different mines, which are often far away from the production plant and usually with very different ore compositions. These plants tend to use the traditional thermal processing steps of smelting, converting to blister, anode refining and casting to produce copper anodes that are then refined in a sulphate electrorefining operation. These thermal steps are in some cases troublesome and require the recycling of considerable quantities of material. A new process was developed taking advantage of the latest developments of the first thermal step of the classic loop, the smelting of copper concentrate to high grade matte or white metal using the well known AUSMELT Top Submerged Lancing Technology. The white metal and/or high grade matte product is converted directly to copper cathode and elemental sulphur using the ECUPREX technology. This approach provides an alternative to the traditional thermal steps of conversion to blister, thermal refining and anode casting, which, especially at small scale, can be expensive and problematic in terms of technical and environmental concerns. At first evaluation, this new process can be operated at low capacities, thereby, changing the traditional approach to copper production. Instead of taking the concentrate to the copper production plant, the copper production plant is taken close to the mine with some significant economic and technical advantages.

Jan 1, 2007

By C. Poon

For slope stability, knowledge of major and minor discontinuity sets that form the rock mass fabric is paramount for pit slope designs. Due to the increased awareness of health and safety in mining projects, efforts have been made to limit structural mapping in order to minimize the risk to personnel associated with approaching potentially unstable areas. Recognizing the importance of such safety precautions, Golder Associates Ltd. is applying a combination of techniques including 3D photogrammetry, conventional mapping and drilling with core orientation to enhance structural data collection. Photogrammetry uses digital photographs to produce a virtual model of a rock mass surface. The application of these techniques will be exemplified through an expansion design of an existing open pit. A comparison of stereonets obtained using these techniques showed some agreements, but also highlighted limitations of each method. The application of photogrammetry was found to be very useful in complementing the other existing techniques.

May 1, 2009

SOFCs with thin electrolyte of two types: SDC (15um) single-layer and YSZ (5um) + SDC (15um) bi-layer were fabricated by screen printing and co-firing on Ni¬YSZ cermet substrates. Using in-situ sintered Sm0.5Sr0.5CoO3 cathode the SDC-cell shows high performance at low temperature, 1180mW/cm2 peak power density around 650°C, while the YSZ+SDC bi-layer cell generates about 340mW/cm2 at 650°C, and good performance at 700-800°C with almost theoretical OCV value. Many Zr-content micro-islands were found on the SDC electrolyte surface. The influence of co-firing temperature and thin film preparation methods on the Zr-islands&apos; appearance was investigated.

Jan 1, 2005

By S. P. Cashin, D. Kashuba, W. Esplin

Barrick has had 6 autoclaves in operation at the Goldstrike Mine, North of Carlin Nevada, since 1993. The 6 autoclaves operate in parallel, processing slurry of gold ore. The gold in the ore is predominantly associated with, and encapsulated by, sulphide minerals. It is necessary to oxidize at least 90% of the sulphide mineral before the gold can be concentrated using a cyanide/carbon-in-leach (CIL) circuit. Sulphide oxidation chemical reactions occurring in the autoclaves are exothermic; however, the sulphide content in the ore is not high enough to operate the autoclaves in an auto-thermal mode. Heat from steam is added to the first 2 of 5 autoclave compartments to initiate the sulphide oxidation reactions. The steam used to heat the autoclaves is supplied by three boilers, which are fuelled with propane gas. The completion of a few operations and maintenance projects in the last 2 years has resulted in a 50% reduction in propane energy requirements. The autoclave operating temperatures were minimized. Excess oxygen addition was held as low as possible. The material of construction for the compartment walls inside the autoclaves was changed from brick to Titanium metal. And, the speed of the autoclave slurry agitators was increased. All of these activities had an impact on the propane energy requirements of the autoclaves. Presented below is a description of the autoclave systems, and a discussion of how the energy needs were reduced, resulting in significant operating cost savings.

Jan 1, 2004

By Jun Shan

The preparation of poly(N-isopropylacrylamide)-monolayer-protected clusters (PNIPAM-MPC) of gold nanoparticles was carried out in a homogeneous phase using three ways, in which three types of PNIPAM ligands were employed. The first type comprised of PNIPAMs with narrow molar mass distributions, synthesized by reversible addition-fragmentation chain transfer (RAFT) polymerization and thus, bearing a dithiobenzoate at the chain end. These polymers were used directly to passivate the gold nanoparticles upon the Schiffrin reaction in a one-pot synthesis. The second type of ligands was derived from the first one through hydrazinolysis, and they therefore contained a thiol end group. The third type of ligands was PNIPAMs obtained through conventional radical polymerization, post-modified to contain thiol end groups. The PNIPAM-MPCs were characterized by high-resolution transmission electron microscopy, and by dynamic light scattering. The one-pot synthesis utilizing the ligands of the first type turned out to be a simple and facile method, compared with the other two ways, with which the size of the gold nanoparticles can be easily manipulated mainly by adjusting the molar ratios of PNIPAM / HAuCl4. PNIPAM is a more efficient ligand to stabilize the gold nanoparticles in water and in organic solvents than alkanethiols. The surface density of PNIPAM chains ranged from 1.8 to 3.6 chain/nm2, which is much lower than that typical for alkanethiols. The thickness of a PNIPAM monolayer bound to the gold core is somewhat larger than the size of the random coil of corresponding free PNIPAM in aqueous solution, which suggests that the conformation of a PNIPAM chain bound to the gold core is to extended.

Oct 1, 2003

By J. C. Escobedo, J. M. Almanza, A. Flores, Cortés. D. A.

Secondary aluminum dross, which has been exposed for several years to atmospheric conditions, was characterized using chemical analysis, X-ray diffraction, optical and scanning electronic microscopy, and energy-dispersive spectroscopy. Based on the characterization, a method to purify the solids is presented. This method starts with the washing of the dross in boiling water to eliminate the soluble compounds like Na and K, followed by the physical separation of the metallic aluminum by milling and screening. Finally, an acid lixiviation process is applied using three different acid solutions, HCl, HNO3, and H2SO4. The best results were obtained using HCl. The main insoluble components of the dross after lixiviation were Al, SiO2, and Al2O3. MgAl2O4, AlN, Si, and Na2Al22O3·2H20 species were also found. Based on the alumina content, the solid product could be suitable as a raw material in the manufacture of castable refractories or metal matrix composites.

Jan 1, 2005

By J. D. Galloway

The mining industry of British Columbia continues to grow steadily in importance. The gross value of the production in 1925, sixty-two and a half million dollars, was a record, and ali indications point to the 1926 output registering a still higher figure. In an industry such as mining, where production means the depletion of known ore reserves, the discovery and development of new &apos;ore-deposits is of the utmost importance. To maintain and increase production, steady development is essential. In this respect, the record of the last three years in British Columbia mining is most satisfactory, as in this period more real development has been carried on than in any similar period in the history of mining in the Province. Prospecting, or the search for new ore-bodies, has also been fairly active, but comparatively few important new discoveries have been reported in the past few years. The mineral output of British Columbia consists of Iode minerals, coat and coke, and building materials. In 1925 the value of the output of these three classes of products was, respectively, about 46, 13, and 3 million dollars. The industry as a whole embraces the mining of these materials, and the treatment and manufacturing processes involved in preparing the various products for the market.

Jan 1, 1926

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed sur?cial mapping and sampling programs in the Separation Lake area of north-western Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of sur?cial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these sur?cial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t)values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sul?de mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from sur?cial samples was compared with that of in situ material. Gahnite from the peraluminous rare-element granite and pegmatite overlapped very well with sur?cial gahnite of Group 1. Gahnite from volcanogenic massive sul?de mineralization and Sedex-type mineralization overlapped well with sur?cial gahnite of Group 2. These results suggest that determination of gahnite composition in indi-cator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By S. Hosseinpour

Chromate conversion coatings (CCCs) are usually applied to these alloys to enhance their resistance to localized corrosion and to improve paint adhesion. The special properties of these coatings such as their low electrical contact resistance (ECR) make them suitable for satellites. This study is aimed to develop advanced CCCs with the proper appearance, morphologies and surface roughness and to evaluate their role on the ECR and thermo physical properties on hardened aluminium alloy of Alclad-7075-T6. Coating characterization was performed by means of scanning electron microscope (SEM) and atomic force microscope (AFM). ECR of coatings were measured by special laboratory designed instrument and a and c were measured by Emissometer and Reflectometer respectively. In addition, corrosion performance of the CCC-coated alloys was determined by 168 hr exposing to salt-spray testing in accordance with ASTM-B117. The results of accomplished experiments on the developed CCCs in this study have been agreeable concerning available acceptability criteria for satellite surfaces.

Jan 1, 2007