Search Documents

By Kevin P. Plucknett, Z. Memarrashidi

"In the current work, factors influencing the corrosion mechanisms of TiC and Ti(C,N) based cermets are reviewed. Cermets were typically prepared with 30 vol.% of metal binder, in the form of various in-situ reaction-formed Ni3Al alloys. Commercial WC-Co hardmetals were also examined as baseline materials. The assessment of corrosion involved a variety of electrochemical measurements, including open circuit potential and potentiodynamic polarisation. The corrosion potential and current density were determined, following Tafel extrapolation, allowing estimation of the corrosion rates. Post-corrosion characterisation involved scanning electron microscopy analysis and associated energy dispersive X-ray spectroscopy of the sample surfaces. It is demonstrated that the primary corrosion mechanism for this type of cermet is dissolution of the metallic phase during oxidation attack, and thus this response can be expected to increase with the amount of binder in the cermet, although degradation can be subtly affected by composition (i.e. alloy composition, C:N ratio, impurities in the ceramic phase, etc.) and test procedure (i.e. aerated vs. de-aerated electrolytes). It was observed that addition of N content into the ceramic phase is beneficial to the corrosion characteristics of TiC based cermets, through significant refinement in the grain size of the hard phase. Similarly, elimination of impurities, such as W in selected TiC powders, also improves the corrosion resistance.INTRODUCTION Cermets are prepared using the combination of a hard, high elastic modulus ceramic phase with a ductile, high toughness metallic binder. This pairing of hard and ductile components ensures wide application of cermets in demanding wear environments. These materials are consequently used industrially in both bulk and coating form. The most common example of such a composite system is based on the use of tungsten carbide with a cobalt-based binder (WC-Co), which has been widely examined over the past 80 years. However, while WC-Co has been shown to exhibit an excellent combination of high strength and wear resistance, the corrosion and high temperature properties of this material are relatively poor. In addition, WC-Co possesses a high density (~13–14 g/cm3), which makes it a less desirable option when the component mass is a design factor (i.e. use in aerospace). In particular, the aqueous corrosion response of WC-Co limits its use in wear environments where combined corrosive degradation may occur (i.e. tribo-corrosion scenarios). Alternate cermet systems are therefore being actively developed due to these performance limitations."

Jan 1, 2017

By James Stenhouse

Abstract The aqueous oxidation of pyrite in caustic solutions under oxygen pressure was investigated by measuring that effect of reaction variable on oxygen consumption by the reactions. From the results of this investigation, a model for the process has been proposed. In this model, sulphur diffuses as a positive ion through an oxide layer which forms on the sulphide particles and is then oxidized to sulphate ion. Iron is oxidized by substitutional diffusion of oxygen atoms into the oxide layer. The effect of most reaction variables on the rate of oxygen consumption can be explained with this model. Introduction Recent investigations (1,2,3) have shown that certain sulphide ores can be readily leached by agitating the ore in the form of a pulp under pressure in the presence of oxygen. Since very little was known of the mechanism of this oxidation, a programme of investigation was inaugurated in 1949 in the laboratories of the Department of Mining and Metallurgy of the University of British Columbia. Financial support for the investigation was received from the National Research Council in the form of student grants and bursaries, from the Canadian Liquid Air Company, Limited, and from the Consolidated Mining and Smelting Company of Canada, Limited. The first objective was to devise a technique to study the primary oxidation reactions in aqueous solutions and to apply the technique to a detailed study of the oxidation of pyrite in caustic solutions.

Jan 1, 1952

By R. L. Christie

"THE ISLANDS lying north of the Canadian mainland, and the large Boothia and Melville peninsulas, form one of the great archipelagos of the world; this sparsely vegetated and nearly unpeopled region extends about 1,500 miles east to west and 1,200 miles from the mainland to the northern tip of the northern-most island. Sea access to most of the islands is restricted by ice to the summer season, and the 'polar pack' ice of the Arctic Ocean presses the year round against the northwest margin of the archipelago. Although the region is remote, the accessibility has greatly increased through a network of weather stations, airfields and air routes connecting with southern centres.The area considered in this paper is that part of the island region underlain mainly by sedimentary rocks. In broad terms, this includes the land and sea areas of the archipelago and the adjacent continental shelf, but excludes the dominantly 'Shield' terrain of Baffin Island, and of Melville and Boothia peninsulas. An impression of the size and potential of this sedimentary region may be gained by comparing some areas: the land area of islands underlain mainly by sedimentary rocks is over 300,000 square miles or about 50,000 square miles greater than the area of Alberta. The total area of the region, including the continental shelf and the inter-island areas, may be double this figure, and may approximate one-seventh of the land area of Canada."

Jan 1, 1970

By A. J. A. Janse

The Argyle diamond mine is located in the Kimberley region in the northern part of Western Australia at approximately 16°43'S, 128°23'E in subtropical bush/shrub savannah. The 46 ha (113 acres) pipe is situated in the Halls Creek mobile zone, which was cratonized about 1800 Ma ago and adjoins the Kimberley Block, a plateau upheld by Early to Middle Proterozoic rocks underlain by presumably Archean basement. The crater and upper pipe zones of the diatreme have been preserved within tilted and faulted strata of Middle to Late Proterozoic age. Its age of intrusion is about 1178 Ma. The diatreme rock is not kimberlite but olivine lamproite which was not recognized as a primary diamond host rock until 1978. The Kalumburu Joint Venture, a syndicate of local and overseas mining companies, started in 1972 to prospect the Kimberley Block with a modest annual prospecting budget of $125,000. Annual expenditure doubled each year and reached $1 million in 1975 after which CRA took over management of the newly-formed Ashton Joint Venture with an annual expenditure of $2 million (all figures are in current US dollars). The Argyle diatreme was found near the end of the eighth field season and after a total expenditure of $12 million. Annual production is about 34 million carats which places Australia as the world's number one diamond-producing country, although, because of the low value per carat, it is number four in terms of total annual value. The global cost required for a major diamond mine is between $300 and $400 million, with a discovery every 10 to 12 years. Because Canada contains large areas of prospective platform rocks underlain by Archean basement it is likely that a major diamond deposit does exist there. It is probable that it will be found before the end of this decade and exploration expenditure may be in the order of $100 million.

Jan 1, 1992

By A. Ignatieff

"Excavation, the principal mining process, 'which hitherto has been based largely on the intuition and logic of mining men, is increasingly receiving the attention of engineers and scientists versed in rock mechanics. The paper intro-duce the principles of this science in simplified form, directed both to underground and open-pit mining. Reference is made to the large annual tonnage from ore and rock excavations, which in 1967 were responsible for 250 million tons of mineral production in Canada.The urge to transform excavation into a continuous instead of an interrupted process is discussed with references to the various types of energies employed or proposed in rock breakage or excavation. Due to the rapid decay of applied energy in the discontinuous and heterogeneous rock environment, large confined blasts proposed for in-situ mining do not give much expectation of success as yet. Raises and ventilating shafts are already bored in reasonably hard rock. Tunnelling machines will be used for drifting and cross-cutting in the future, but continuous mining machines of the cuttmg and shearing type are not 'around the corner' for stoping typical orebodies. On the other hand, bed mining, particularly of coal, has led the way in continuous mining, and Remotely Operated Long-wall Face (ROLF) experiments are progressing in an encouraging way. Some reflections on the mining environment in relation to the human element are made."

Jan 1, 1970

By J. A. Rogers

"The Arthur W. White Mine (formerly Dickenson Mine) is a structurally controlled, hydrothermal gold deposit. A gold producer since 1948, it has, to December 31, 1990, processed 6.9 million (m) tons (T) of ore grading 0.45 ounces per ton gold (oz/T Au). As of December 31, 1991, Proven and Probable Ore Reserves were 3.2 m. T. at 0.32 oz/T Au. The mine is located just east ofPlacer Dome Inc. 's Campbell Mine, within the Cochenour-Gull.rock Lake deformation zone. It is situated on the hanging-wall side of a southeast-plunging anticline in a sequence of metamorphosed Archean volcanic, sedimentary and plutonic rocks of the Red Lake greenstone belt. Ore-bearing structures, found mainly within basaltic rocks, are brittle within greenschist-facies rocks to the northwest, but become more ductile toward the southeast, in amphibolite-facies rocks. Within and proximal to these structures, carbonate and arsenopyrite alteration decreases, whereas biotite, actinolite, pyrite and pyrrh otite all increase to the southeast.Ore and shear structures occur symmetrically about the northwest-trending, steeply southwest-dipping, flattening foliation . The three most common ore trends are on average: (A) northwest trending with a 55 degree to 85 degree dip to the southwest; (B) north-trending with a 40 degree to 50 degree dip to the west; and (C) due east-west-trending with a vertical dip. In general, the dominant direction of economic gold concentrations are explained and thus predicted by considering deformation style (brittle or ductile), rock anisotropies such as bedding and lithological contacts, and direction/magnitude of relative block movement. Direction ""A"" can be found adjacent to both right- and left-handed faults. Direction ""B "" occurs with dominantly right-handed systems and direction ""C"" is found with predominantly left-handed movement. Major faults active prior to, during, and after ore formation can have offsets in the order of 2500 feet. Movements along these faults were transpressive while their conjugate breaks were dilatant, thus creating zones for alteration and ore solution emplacement. A series of faults , each with offsets up to 30 feet were established under lower temperature brittle conditions during late- to post-ore formation. In more complex zones, formed during more ductile deformation, these faults controlled the localized geometry and, thereby, the depletion and enrichment of ore shoots, causing a high nugget effect.Although an important aspect of production planning and monitoring, grade control is also very important within a complex ore zone so that the nuggets are not missed. Detailed observation of structure at the hand-sample scale and detailed mapping at the stope scale give valuable clues to interpreting the structures on a mine-wide scale. Determining the relative movement along fault structures is very important so that using an action-reaction- type logic, potential dilatant areas can be predicted and targeted for development and diamond drilling."

Jan 1, 1992

By W. Harry Foster

"Asbestos Corporation Limited, incorporated in 1925, operates four asbestos mines and three asbestos mills in the Thetford Mines 1•egion of Quebec's Eastern Townships. A unique asbestos orebody, located in the Ungava Peninsula of Nouveau Quebec, was purchased by Asbestos Corporation Limited in 1964 and commenced production in 1972. As there were no existing facilities in the isolated, arctic region of Asbestos Hill, it was necessary for Asbestos Corporation Limited to construct at Deception Bay a deepsea wharf, a large ungraded fibre shed, a power plant and camp facilities. Forty-two miles of road were needed and were constructed from Deception Bay to Asbestos Hill. At Asbestos Hill, a complete crushing-drying-milling complex, a power plant, pe1•sonnel accommodations and open-pit facilities were provided. Unloading facilities and a fib1•e finishing mill we1l constructed at Nordenham, West Germany. The ""Asbestos Hill- Nordenham Story” is divided into individual papers covering all aspects of the engineering, construction and operation of this unique enterprise. Particular emphasis has been placed on those unusual aspects caused by the isolated location, arctic conditions, short shipping season and the deep permafrost."

Jan 1, 1976

By S. Hopkins, J. Nolan, S. Gillis

"Cast in place concrete shaft linings have been used in many salt and potash shafts sunk in North America over the last 100 years. A large number of these shafts have exceeded their initial design lives and as producers look to extend the life of their operational assets, maintenance costs and shaft downtime will, in many cases, continue to rise unless repair work is undertaken. Successfully implementing concrete liner repair schemes in operating salt and potash shafts is complicated due to their age, environment and time constraints during inspection, detailed design and construction. This paper outlines a general approach to the repair of concrete-lined portions of these shafts, based on lessons learned from the authors’ involvement in a recent repair project. INTRODUCTION Prior to the recent boom in potash mine construction many of North America’s potash mine shafts were entering their sixth continuous decade of production (Table 1). Of North America’s salt mines, one has been in continuous production, for nearly nine decades.As would be expected, considering the environment in which these liners operate and the age of the material, the concrete-lined sections of the shafts outlined in Table 1 have been noted by the authors to have lost both cross-sectional thickness and strength over time. Since construction, three principal factors have contributed to this loss in section/strength; (1) physical degradation (impact, freeze/thaw or rebar expansion), (2) chemical degradation from brine/water inflows (Neville 1969; Bothwell, 1972) and (3) overstressing of the liner. These factors may act in combination, in which case they can produce more significant distress than individually. Physical degradation There are three main causes of physical degradation of concrete shaft liners. The first is impact from falling debris/tools or equipment (whether large or small), which may damage specific sections of concrete lining as they fall through the shaft. Impacts tend to damage infrastructure fixed to the shaft liner more than the liner itself, so damage from this mode of failure is usually localised, for example, where bolts fixing a shaft services bracket to the wall have been pulled away, pulling out the concrete around the bolts with them."

Jan 1, 2019

By L. L. Sirois

Because segments of the Canadian mineral-based economy are dependent totally or in part on foreign sources of certain minerals, their well-being may well be affected by inability to obtain these minerals. Where such dependency exists, it is therefore important that contingency plans be available to counteract possible price increases or lack of supplies by means of technology, developed well in advance of any pending crisis . Canada is vulnerable to possible future real or artificial shortages of certain foreign-produced mineral commodities, and science and technology can provide information for the development of policies for counteracting efforts by foreign exporters to control prices or limit supplies.

Jan 1, 1977

By J. A. Morgan, P. M. Dimmell

Abstract - The Aubry pegmatites are located on the Seymour Lake property, 15 km north of Lake Nipigon in northwestern Ontario. The property lies within the Caribou Lake-Marshall Lake greenstone belt along the English River-Wabigoon subprovince boundary of the Superior province of the Canadian Shield. The property was optioned in March 2001 by Linear Resources (now Linear Gold Corp.), who carried out gridding, prospecting, geological mapping, soil and lithogeochemical sampling, trenching, channel sampling, and a total of 1,866 m of diamond drilling in 32 holes. The Aubry pegmatites are classified by Breaks et al. (2003) as complex type, spodumene-subtype, lithium-cesium-tantalum pegmatites (Cerný, 1989). These pegmatites generally form under high-pressure-low-temperature conditions, display complex internal zoning, have relatively low Nb/Ta ratios in the ore-forming assemblages, and contain significantly elevated tantalum values (Cerný, 1989). Other examples of spodumene-subtype pegmatites include the formerly producing Hugo pegmatite in South Dakota, and the currently producing Greenbushes pegmatite in Australia. The Aubry pegmatites occur as an undulating system of stacked sheets that dip moderately to steeply eastward over a 1-km strike length. The main portion of the North Aubry pegmatite ranges in true thickness from 10 to 28 m over a strike length of 125 m, whereas the thickest portion of the South Aubry has an estimated true thickness of 15 to 16 m over a minimum strike length of 95 m. The North Aubry pegmatite remains open downdip and along strike to the north, whereas the South Aubry pegmatite remains open downdip and along strike in both directions. The Aubry pegmatites are among the most highly evolved in Ontario, with the southern end of the North Aubry (trench 5/6 area) being the most highly fractionated (Breaks et al., 2002). Channel samples from the trench NA-5 area of the North Aubry pegmatite produced values up to 2.49 wt.% Ta2O5 over 4 m. Coarse manganotantalite crystals, up to 5 cm in diameter, from this trench contain up to 84.9 wt.% Ta2O5 (Breaks et al., 2002). Drill hole SL02-31 in the trench NA-6 area gave values of 0.046 wt.% Ta2O5 over 17.7 m, including 1 m @ 0.464 wt.% Ta2O5. Further exploration will focus on defining the grade of the North Aubry zone, extending and defining both known pegmatites, and identifying additional Ta-rich zones within them. Lithogeochemical and enzyme leach soil geochemical data suggest the presence of multiple undiscovered pegmatites on the property.

Jan 1, 2005

By L. J. Visentin, J. G. Rickaby

"Audiometric testing is a key element in hearing conservation in the mining environment. This paper gives the history of the audiometric testing program carried out by Inco Metals Company, including the program objectives the personnel and equipment involved, calibration and testing, the test procedure, and the classification and evaluation of the test results.IntroductionThe operations of the Ontario Division of Inco Metals Company are located primarily in the Sudbury District. They also include a refine ry at Port Colborne and a mine and concentrator at Shebandowan near Thunder Bay.The company operates nine underground mines, and one open pit, while maintaining six underground mines on a standby basis. Ore from these operations is processed in four concentrators. The metallurgical facilities include a smelter, a matte processing plant, a copper refinery, a nickel refinery and an iron ore recovery plant at Sudbury, and a nickel refinery at Port Colborne. Inco Metals currently mines roughly 9,000,000 tons annually and produces IS elements.Excessive noise in the work place has been a serious problem in the mining industry since the introduction of compressed-air-powered machinery in the last century. At the same time, growing levels of noise inherent in our social environment can threaten the hearing of employees and their families.Only in the last 20 years, however, has the extent of this problem and its implications for people working in the industry and their families been recognized. Since the industry has become aware of the situation it has taken steps to implement comprehensive noise reduction and hearing conservation programs."

Jan 1, 1982

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The hydrotransport systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1,500-2,000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed and installed at Aurora, incorporating significantly increased impeller diameter and pumping vane lengths. The new pumps are expected to triple Aurora’s previous mission length for hydrotransport pumps. Part II of this paper will share actual hydraulic and wear performance observed in the first several months of operation, and draw comparisons relative to what was expected for these pumps in design / development.INTRODUCTION Slurry Pumps are Critical Equipment at Syncrude Slurry pumps are a key component in Syncrude’s operations. In a typical Aurora application, each 5000 HP pump stage helps move over 8,000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1,500 to 2,000 hours, or 12 to 16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in unduly high impeller vane leading edge speeds for the service conditions."

Jan 1, 2014

By D. Wolfe, R. Cleminson

"The Aurora North mine has been operating for more than ten years, and is the source of over half of Syncrude’s bitumen production. The slurry systems at Aurora experience high rates of wear, and mission lengths on current slurry pumps are nominally 1500-2000 hours. Recent work has enabled a better understanding of the significant adverse effect of large particle impingement damage to impeller vane leading edges - which is the known life determining issue for Aurora hydrotransport pumps. A new pump design has been developed with a larger diameter impeller and increased vane lengths, and is expected to triple Aurora’s mission length for hydrotransport pumps.INTRODUCTIONSlurry Pumps are Critical Equipment at SyncrudeSlurry pumps are a critical component in Syncrude’s operations. In a typical Aurora application, each pump stage helps move over 8000 dry tonnes per hour of oil sand, plus an equal volume of process water that has been added to create the slurry. The average impeller life in oil sand hydrotransport service at Aurora has been nominally 1500-2000 hours, or 12-16 million tonnes of oil sand pumped. Generally, the slurry pump application at Aurora has proven very difficult to improve due to the unique combination of high sand abrasivity, 125 mm (5”) large particle top size (lumps), and high flow rate relative to basic pump size; a factor that results in higher than optimal impeller vane speeds for the service conditions.PROJECT BASISSlurry Pumps are the Reliability Bottleneck at AuroraSlurry pumps are currently the shortest-lived components that determine the overall system run length at Aurora, in Hydrotransport, Extraction and Tailings. Vibrating screens and piping had been previous bottlenecks, but their reliability has been improved through upgrades in equipment design and wear materials. Both vibrating screens and piping can now achieve 4000 hour mission lengths."

Jan 1, 2013

By R. Matusewicz

The key drivers for the copper smelting industry are a complex mix of economic and "human" factors which combine to drive technology in new directions and can provide a strong indication of future industry trends. Recent examples have been the drive to achieve increased scale of production and resultant cost efficiencies by using a single furnace high intensity smelting vessel, and the broad acceptance of Top Submerged Lancing (TSL) technology for this duty. The development and adoption of continuous converting processes to counter the increased pressures faced by the Peirce Smith converting process is another example of the need for innovation. This paper discusses the merits of the continuous converting process, describes how the Ausmelt TSL batch converting process has been adapted to the new Ausmelt Continuous Copper Converting (C3) process in response to these industry trends and examines the Ausmelt continuous converting flowsheet options available to the end user.

Jan 1, 2007

By Trevor McGiddy

"Australia's prosperity relies significantly on income generated from exports of resources and agricultural products. In 1989-1990, coal was Australia's most valuable export commodity, contributing. A $5.7 billion or 14% of all export income.The abundance and quality of its coal resources and the proximity of Australia to the rapidly developing economies of Southeast Asia were significant factors that encouraged export-oriented growth and investment and will continue to do so. On the other hand, the 1980shighlighted the sensitivity of the industry to international changes in supply and demand, currency and socio-political forces.Following many years of disappointing returns for investors, mainly as a result of falling Australian dollar coal prices, resolve will be necessary to maintain competitiveness with resource-rich nations. In recent years, operators, unions and governments have begun to embark on a long overdue rationalization of domestic issues in a bid to increase productivity and reduce costs.The nature of mining operations is also changing; deeper surface mines and the growth of longwall mining will require the development of new technology and skills. Other challenges emerging from the international environmental debate will require that Australia responds appropriately to demands for cleaner fuels, energy efficiency and environmental responsibility.The future development of the Australian coal industry will therefore be influenced by its own ability to become more efficient and mature in the production of quality coal products and through rational international response to environmental questions."

Jan 1, 1992

By David L. Anderson

"The government o f Canada has, since 1981, been under intense political pressure to modify its foreign direct investment (FOI) regulatory regime(1). To date the government's response has been limited to administrative and ""cosmetic"" changes: substantive issues have been largely ignored(2). However, as long as the economy continues to flounder , the Foreign Investment Review Agency (FIRA), as it is presently formulated , will continue to be an easy target for government critics . This phenomenon, in conjunction with the virtual certainty of a federal general election within two years, suggests that changes to the FIR Act will be seriously entertained by the present government.Recent events indicate that if change s are made, they will likely entail the adoption of a special-sector approach within the existing framework of a general screening system(3). Since this approach is currently employed in Australia(4), it would seem to be appropriate, from a public policy perspective to study that country's experience in developing and operating such a scheme. In doing so, I shall focus on the mineral sector; the rationale for doing so is as follows. First, this sector served as the focal point of the Australian FOI regulatory debater(5), Second , with the exception of the oil and gas industries, the non-petroleum mineral sector is one of the few areas of the Canadian economy wherein the Trudeau government has adopted an explicit domestic ownership target(6). Third, the non-petroleum mineral sector is, undoubtedly, a prime candidate to be denoted a s a special-sector if such a framework were to be utilized by the Canadian government!"".Although international comparisons are fraught with danger , a Canadian/Australian comparison is particularly appropriate(8). Both countries have reasonably similar economic, political and social structures . Furthermore, as noted above , Australia is the only other western country which employs a general screening mechanism for FOI. In addition, it utilizes a special area approach ; within this scheme, an explicit target of a minimum of 50% Australian ownership of all new resource projects has been formulated and clearly promulgated to all of the relevant interest groups. This policy, broadly defined, has been in place for more than six years and during this time the Australian mineral sector has, by world standards, prospered(9). Hence, the Australian experience in designating the mineral sector as a key area within a general screening system, should be of interest to Canadian policy-makers."

Jan 1, 1984

By A. Ignatieff

"Demonstrations of Automatic Coal Burning EquipmentAT THE 1951 and 1952 Annual Coal Research Conferences sponsored by the Dominion Coal Board and attended by delegates from the Dominion and Provincial governments as well as industry, the importance ,of encouraging the co-operative interest of Canadian coal and equipment industries in •promoting the use of equipment types best suited to burn given Canadian coals was emphasized. It. was suggested that this idea •be enlarged upon at forthcoming C.I.M. meetings that would be .attended largely by coal mining engineers.With this in view, a Domestic Heating Forum (1) was featured in the Coal Division programme at the 1951 Annual Western Meeting of the Institute in Calgary, and a much more ambitious programme, highlighted by live demonstrations, was •staged at the combined Annual Western Meeting and Fourth Meeting of District 4 held in Winnipeg in October 1952.With the excellent co-operation of a number of equipment manufacturers and coal companies, and with facilities kindly provided •by the University •of Manitoba authorities, burning demonstrations were• arranged in the Agricultural Engineering Building, on October l 7th. These demonstrations were a fitting sequel to the Coal Division sessions held in the Royal Alexandra Hotel on October 16th, at which the combustion of coal was specially featured in a series of papers by prominent Canadian and United States specialists.The primary purpose of the demonstrations was to •show that all coal, regardless •of rank, can be satisfactorily used provided that proper application is made with equipment suited to its purpose."

Jan 1, 1953

By M. Soleimanifar

With more and more industrial construction projects implementing RFID and other sensor-based technologies on fabrication and project sites, new innovative processes are needed to help automatically read and re-position RFID tags while reducing the cost to deploy RFID infrastructure over large areas. RFID tags are being used on construction sites to help identify the location of materials, equipment and personnel to aid in finding project critical materials and equipment required to construct the industrial facility on time and on budget. This research provides a cost-effective process for reading tens of thousands of RFID tags over large project sites from outdoor laydown yards, to warehouses to the workface where the materials and tagged equipment are installed. Based on the collected RFID and sensor data, localization mechanisms determine the most recent coordinates of the tagged components. The paper will cover analysis of RFID collected data and key lessons learned from a commercial deployment of the SiteSense® system with one Alberta-based industrial contractor, JV Driver Fabricators, at an 80-Acre module, pipe spool and structural steel fabrication site.

Aug 1, 2013

By L. Juteau

"""The north coast of the St. Lawrence River will be the scene of an industrial development during the coming decades"". The facts which underlie this statement are the occurrences of iron and titanium ore, the abundance of hydro-power and the availability of deep-water ports in this region. Havre St-Pierre, Sept-Iles, Port Cartier and Baie Corneau already exist as major ports and urban centers. The huge quartz deposit at Baie Comeau will be a decisive contributing factor in the development of a metallurgical plant in this area. Due to its purity, it lends itself, first of all, to the manufacture of glass of different kinds, being comparable to the quartz sands now used by the plate glass and glass container industries in the Montreal area, Moncton, N.B., Trois-Rivieres and - in the future - at Bécancour, Quebec. However, its high quality will also make it possible to use it as one of the main basic materials for the production of silicon carbide and ferrosilicon, and as a flux in metallurgical processes. It is intended, in this report, to offer conclusive proof of the economical importance of this large quartz deposit by presenting the results of the studies made to date."

Jan 1, 1971

By W. W. Muir

"The Baker Mine used a 100-ton per day conventional cyanide leach mill located in northern British Columbia. A production decision was made in early 1980 and the mill was on fine in April 1981.Ore reserves had been estimated at 100,000 Ions averaging 0.9 oz gold per ton and 18 oz silver per ton . Mineralization consists of electrum (Au/Ag) and acanthite (Ag2S).This paper will review plant design and focus on some problems associated with start-up and early operation with the intention of assisting other mine operators by indicating potential problem areas.IntroductionThis paper will discuss operating strategies employed at Baker which improved over-all mill performance. Also included are some ideas which could be steps toward a more efficient operation in a similar setting.Actual dore production by mine life was 37,606 oz gold and 742,117 oz silver.Figure 1 illustrates the relative stability attained over the mine life. Metal recoveries for gold and silver were 92% and 85% respectively.Safety at Baker was of prime importance because of its remote location. Baker received the Mine Safety Association ""Small Mines Award "" in two of its three operating years. At shutdown in late 1983 the mill had operated for over 850 days without a lost-time accident."

Jan 1, 1985