Search Documents

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

By Caithness SJ, Heape JMT

Following the discovery by CRA of gold at Mt Kare, and the subsequent 1988-90 gold rush, mechanised mining of the alluvial resource is now being carried by a company jointly owned by CRA (51%) and landowners of the area (49%). Mining is currently being carried out using small gravity processing plants fed by hydraulic excavators. Use of hydraulic mining techniques will be limited to over- coming difficulties related to the high clay content of the material and the soft nature of the bedrock. Current resource estimates suggest that the alluvials will have a mining life of three to four years. During this time, exploration of the hydrothermal gold mineralisation at Mt Kare will be carried out by a wholly-owned company of CRA. It is hoped that this will lead to establishment of an economic primary gold resource.

Jan 1, 1991

By A. S. Macfarlane

Mineral resource management (MRM) practice has developed in South Africa over the course of the last ten years, with the purpose of integrating previously isolated technical functions into a value chain aligned, process organization, responsible for mine planning and optimization. The implementation of MRM within various companies has met with varying degrees of success, often resulting in incremental improvements in the planning process and, conversely, often becoming the scapegoat for poor delivery on plans and projects. The reason for this has been, amongst others, a lack of a suitable metric to define the success rate of MRM in the business at hand, in terms of its contribution to the bottom line. This paper is the result of extensive research by the author into this subject, which has resulted in the conclusion that economic value added is an appropriate measure that will lead to real optimization and value creation in mining companies, if applied within a new, holistic model

Jan 1, 2006

By S. Uddin

An integrated device has been developed to measure sedimentation potential, conductivity and pH simultaneously of particulate systems. Maxwell?s model was used to calculate volume fraction of solid from the conductivity data. In this approach, all system variables are known and zeta potential can be calculated from Smoluchowski?s equation. The technique is validated by comparing zeta potential vs. pH for alumina and silica suspensions with electrophoresis measurements. The technique was extended to mixed alumina/silica systems. Sufficient column height along with size difference between the two minerals allowed gravity fractionation during settling. Sedimentation potential measured over time identified the transition from one mineral to the next. Using XRD analysis the results supported the correlation between surface charge and sample composition. This is a step towards characterizing surface charge of mixed systems of interest in mineral processing.

Jan 1, 2010

By M. R. Smith, H. Kanli

The impact crusher is a popular device for producing crushed aggregates from non-abrasive rocks such as limestones, offering the advantages of high reduction ratios and relatively low installed costs. To extend the application of a process-flowsheet simulator to the quarrying industry, a mathematical model of an impact crusher was therefore developed using the general crusher models of Andersen and Whiten as a basis

Aug 1, 1995

By R. Lahtinen, M. Tiainen, R. Salminen

The application of similarity analysis derived from regional geochemical mapping data to the location of Ni-bearing intrusions was tested in southwest Finland, where a well-known nickel belt is situated. Samples of till from the vicinity of the Vammala and Kylmakoski Ni-Cu deposits, which were collected independently of the Geological Survey of Finland's regional geochemical mapping programme, were used to provide geochemical modelling data. The data consist of the aqua regia-leachable concentrations of 20 elements from the less than 0.06-mm fraction of glacial till. The variables used in the similarity analysis were selected on the basis of a factor analysis in which the method of oblique rotation was used. A hierarchical clustering of the modelling samples produced two main groups. The first group was described as the "nickel deposit environment model" and the second as the "nickel deposit location model". The data for the standardised variables were compared sample by sample with the model data by similarity analysis using the Simana program with a cos theta measure of pattern similarity. The nickel deposit environment model delineated the known Ni belt and indicated an extension to the east. The nickel deposit location model identified target areas of reasonable size with the greatest potential for Ni ores within the nickel belt

Dec 1, 1991

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By Robert A. Miller

This computer program determines the price per ton of coal needed to obtain a profit of 12 percent discounted cash flow. From a predetermined equipment and manning list, the program calculates all costs and prints seven tables, Including the equipment and manning tables and the discount cash flow table. Forty-four of the input variables may be readily changed to study their effects upon the final price per ton of coal or upon individual cost items. The method is adaptable for any type of mining and with additions, for beneficiation processes. This program was written in Fortran IV for use on the IBM 11302 and with few modifications can be used on other computers.

Jan 1, 1971

By P. Klaus

"KfW IPEX-Bank is the commercial arm of KfW Bankengruppe, responsible for international project and export finance.KfW was one of the first banks in Germany to promulgate environmental guidelines for its commercial business activities. These guidelines were first made public in 2000 and updated for the second time in 2004. They now include specific reference not only to environmental but also to social concerns. The guidelines specify the procedures to be followed in assessing credit risks related to environmental or social hazards.The bank considers sustainability as an interdependent framework of economic, ecological and social factors. In its efforts to contribute to sustainable development worldwide the bank uses its influence as far as possible to improve a project’s performance if such improvement is deemed necessary."

Jan 1, 2005

By Paul Hatmaker

Lime was a highly useful commodity thousands of years before the simple chemistry of its manufacturing process was known. The employment of lime for agriculture, building, and even certain essentially chemical purposes is so old that its origin is among the unrecorded details of man's first ventures into the manufacture and use of prepared substances. Lime is a most versatile material and consequently has come to be widely utilized in modern civilization. Immediately before the depression of the early 1930's the annual production of lime in the United States was more than 4 million tons, valued at 33 to 42 mil-million dollars. This output was sold to many industries, so many that mere enumeration becomes tedious.

Jan 1, 1934

By M. Kumral

The efficiency of an ore-processing unit depends on the consistency of the characteristics of raw material entering the plant. When the mined ore is highly variable in quality, the only way to ensure consistency is to homogenize the ore prior to feeding to the processing plant. The homogenization can generally be achieved by the bed blending operation. Given that the stockpiling and reclamation processes are very expensive, it is necessary to design the process in such a way as to minimize variabilities of specified properties of raw material. In this paper, for alternative stacking types, optimal stockpile geometry is found in three stages: First, stockpile input is simulated by sequential Gaussian simulation, and then the variance reduction ratios (VRR) as a criterion of stockpile efficiency are calculated for various stockpile geometry scenarios by a stockpile simulator written in FORTRAN. Second, multiple regression analysis is performed to model the VRR by the use of stockpile length, the number of layers and stacker speed as the independent variables. Finally, the model is an optimization problem. Decision variables are the stockpile length, the number of layers, stacker speed and stacking type. The genetic algorithms (GA) are used to minimize the VRR. The approach was demonstrated on data from an iron orebody. The problem was to reduce fluctuations of iron, silica, alumina and lime contents in the stockpile output. The results showed that the approach could be used for the bed blending design efficiently. Keywords: bed blending design, multiple regression analysis, genetic algorithms, iron ore, content fluctuation

Jan 1, 2006

By Robert Jakiel

The following paper is being presented to provide an understanding of the Deep Soil-Cement Mixing (DMM) performed at Contract C09A7 at the Fort Point Channel Site (FPC), for the I-90/I-93 Interchange of the Central Artery/Tunnel Project (CA/T), Boston, MA. The paper is written as a summary of the DMM from the DMM Contractor's perspective. The summary provides technical information and practical observations that are currently considered to be state-of-the art knowledge within the soil mixing industry. The observations and information are being provided by Robert L. Jakiel, Chief Engineer of SMW Seiko, Inc., who was the DMM Project Manager and Project Engineer for the A7 Joint Venture at FPC. The DMM was started in April of 1996 and completed in December 1999. The various acronyms and terminology used to describe the soil mixing are found in a section at the end of the paper.

Jan 1, 2000

By P Holtham, K Duffy, W Valery, A Jankovic

As high grade ore deposits are depleted, remaining deposits are generally lower grade and require the mining and processing of larger volumes of material per tonne of product. These low grade deposits often contain a large proportion of barren gangue. Pre-concentration aims to remove this barren material at as coarse a particle size and as early in the process as possible. This has the potential to reduce processing costs, energy and water consumption, increase production and improve resource utilisation.There are several technologies that may be applicable for pre-concentration. This paper looks specifically at bulk ore sorting and how it can be integrated into existing or new mining operations to improve profitability and reduce environmental impact. Bulk ore sorting is the separation of barren gangue from a fully loaded conveyor belt based on the grade as measured or inferred from a sensor measurement. It may be used to increase the production rate through fixed plant capacity, or increase production and/or reduce the size of downstream processing equipment in Greenfield operations. Marginal ore sub-economic reserves may be upgraded, making them economic to treat and improving the resource utilization. Bulk ore sorting could also be used to reduce dilution and ore loss in mining operations by improving grade control, or to separate ore types to treat via different process routes. Various applications of bulk ore sorting are discussed in this paper, and three cases are investigated considering the impact on the overall operation and the associated benefits.CITATION:Duffy, K, Valery, W, Jankovic, A and Holtham, P, 2015. Integrating bulk ore sorting into a mining operation to maximise profitability, in Proceedings MetPlant 2015, pp 273–287 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By Becerra J. O

HYL developed a direct reduction process (DR) that does not require a reformer; it is called self-reforming process. Typically, direct reduction processes based on natural gas utilise a reformer unit to transform the natural gas into reducing agents (hydrogen and carbon monoxide). The reforming reactions are: CH4+H20-?3H2+CO CH4 + CO2 - 2H2 + 2CO These reforming units require a catalyst agent to promote the kinetics of the reforming reactions. The catalyst for these reactions is typically a metallic element such as nickel in a ceramic matrix; iron is also an excellent catalyst for the reforming reactions.

Jan 1, 1999

By Jon Sinnreich

Ensuring the accuracy of collected data during deep foundation static load tests is of paramount importance. Typically, pile head displacements are measured relative to a purpose-built reference system, which is assumed to be fixed. This study presents a simplified error analysis of this assumption, illustrates the potential magnitude of these errors, and proposes an improved method of pile head displacement monitoring.

Jan 1, 2009

By G. S. Austin

The St. Cloud Mining Company extracts clinoptilolite about 6.5 km south of Winston, Sierra County, New Mexico. Production is about 18,000 mt/year. Natural zeolites are good adsorbents for positively charged solutes such as ammonium. St. Cloud’s production is used in animal hygiene, animal feed, environmental mitigation, air and water filtration, and other applications. By a simple chemical treatment with a surfactant, zeolites can also be modified to adsorb negatively charged solutes such as nitrate and arsentate, and neutral organics such as solvents and fuel components. These surfactant-modified zeolites are used in treating groundwater contamination, stormwater runoff, and solvent vapors from painting operations.

Jan 1, 2002

By V. I. Lakshmanan, Dan A. Mackie

Traditional vat leaching methods have had limited success, primarily due to the high cost of loading and unloading the vats. In general, such batch methods are labor-intensive and costly. Heap leaching has emerged as a viable, low- cost alternative, but low recoveries, normally in the 70% range, offer opportunities for improvement. Also increased regulatory guidlelines for effluent and spent heap leach pads disposal offer potential for alternative methods. The Mackie Vat Leaching Jig (MVLJ) has had its incubation at Ortech International, where bench scale through pilot scale testing continues. Design developments and testwork over the past two years indicate that the time may be right for field trials.

Jan 1, 1990

By I. A. Mwamba

Titanium sponge, which is almost pure titanium, is extremely ductile and not easily processed into titanium powder. One method of producing powder is the hydride-dehydride (HDH) process, where titanium sponge is hydrided to form brittle titanium hydride (TiH2). Titanium hydride is easily milled to produce powder and is then dehydrided to form Ti powder. In this work, titanium hydride powder obtained from titanium sponge was used as a starting material for blending and mechanical alloying with elemental powders. Firstly, titanium hydride powder was blended with aluminium elemental powder to produce a homogenized powder, which was then compacted and sintered to produce powder metallurgy compacts. Secondly, titanium hydride powder was mechanically alloyed with aluminium elemental powder and then compacted. The mechanically alloyed powder was characterized in terms of particle size distribution, morphology and microstructure. In both blending and mechanical alloying, the green compacts were characterized by assessing the green density, while the sintered compacts were characterized by their sintered density, microstructure, and hardness. The two processes have resulted in the formation of TiA13 intermetallic compound. It was established that by simple mixing and homogenizing, titanium hydride can be used as a starting material to produce powder metallurgy components in which porosity is a benefit rather than a problem, much akin to metallic foams. From the products obtained in the TiHz-Al system, it appears that titanium hydride can be used as a precursor in mechanical alloying. However, the possible formation of complex hydrides may introduce detrimental properties, and needs to be further investigated. For the production of non-porous components, it would be advisable to dehydrogenate the TiH2 powder before milling i.e. producing titanium powder by the hydride-dehydride (HDH) method. Keywords Mechanical alloying, titanium hydride, titanium aluminide and blending

Jan 1, 2011