Search Documents

By A Maldonado, A Robert, K G. Mercer

The Hamersley Group in the Pilbara, Western Australia, consist of interlayered banded iron formation (BIF) and shale host rock formations within which a large number of open pit iron ore mines have been established. The slope stability of most of the mining excavations developed within these formations is controlled by the relatively low shear strength of the shale groups and shale bands, which are the weakest rock types. Shale formations range from fresh to highly weathered and are generally highly fissile when fresh, and clayey when weathered. An accurate understanding of the shear strength of these materials across the entire weathering continuum is therefore a key importance for assessing the slope stability of these mines.Historically defect laboratory testing results for the Pilbara mines have been analysed mechanically using direct shear testing (DST) to measure a number of geotechnical characteristics of the rock bedding and defects. This paper sets out the current practice in the industry in terms of the laboratory testing and presents a possible application of hyperspectral data to empirically correlate the shear strength of shale bedding with the relative mineralogy abundance on the bedding surface. This was achieved by creating both hyperspectral and geotechnical data sets for the same samples.In the study the shale samples were separated into three distinct assemblages: iron oxide + kaolinite, iron oxide + white mica + kaolinite, white mica + kaolinite, which had 40, nine and two samples respectively. Analysing these assemblages alongside DST data showed that samples with white mica had reduced non-variable shear strength, whereas samples with iron oxide + kaolinite had an overall higher shear strength but with a greater variance. It is inferred that the reduced shear strength in the white mica samples is due to the sheet (or plate) like structure of the mineral, giving it a weak stress plane. Confidence in the trends observed can be reinforced by expanding the data set in future works. The investigation also includes a discussion on weathering grade and addresses the question as to whether mineralogy abundances influence these characteristics in Hamersley shales.CITATION:Maldonado, A, Mercer, K G and Robert, A, 2017. The relationship between mineralogy and shear strength of Pilbara Hamersley Group shales across the weathering spectrum, in Proceedings Iron Ore 2017, pp 423–430 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By L. A. Roe

Magnetic separation of iron ores is one of the fastest-growing segments of the minerals beneficiation industry. The tonnage of taconite ores processed annually by magnetic separation will, in a few years, reach 100 million. Magnetic separation occupies an attractive position in the field of ore beneficiation. It is a simple yet effective method, used for some 150 years and steadily growing more important. This type of beneficiation orginated in 1792, when William Ful-larton was issued a British patent covering the separation of iron ore by magnetic attraction. What is magnetism, and why are some materials capable of being magnetized and others not The study involves many unknowns, and even a partial answer to these questions would be a dissertation in solid state physics and perhaps other fields of science. But the last two decades have revealed basic facts as to why certain materials are magnetic and what happens to them when they are magnetized. Some of the newer studies in solid state physics have developed a theory that can be applied to studies of magnetism. It is claimed that magnetism stems fundamentally from the spin of electrons in atoms that tend to go in pairs, spinning in opposite directions. The atom as a whole can act as a magnet only when there is an imbalance of electronic spin. Whenever an atom has an odd number of electrons, therefore, this imbalance exists. This neutralizing effect explains why a piece of material that contains atomic magnets is not necessarily magnetic. The physicists tell us that iron is composed of many small magnetized regions called domains, which consist individually of millions of atoms. The piece of iron becomes magnetized when an external force lines up these domains in the same direction. Fundamental data developed by physicists working in fields far removed from minerals beneficiation are now available for developing better magnetic separators for ore processing. More Data Needed on Magnetic Properties of Minerals: There is less information on magnetic properties of minerals than there is for certain aspects of magnetic separator design. When the data on magnetic properties is available, it is often directed toward the study of powders for tape recorders and other highly scientific endeavors that are of little use to the beneficiation engineer. W. R. Crane's table of tractive forces, published in 1902, is still a guide in the study of magnetic minerals. Bits of other information regarding electrostatic conductivity, dielectric constant values, and permeability of various minerals have also appeared but are of small practical value in magnetic separation of ore. It is extremely important to obtain pure mineral specimens for making investigations and to record results that may be of use in studies of magnetic processes. Reference to the large volume of data developed by those concerned with analysis and design of permanent magnets soon reveals that these people have extensively evaluated the effect of various impurities on magnetic properties. Much of the science of the ferrite industry is based upon spinel-type structures which are varied by substitution of selected elements or even subtraction of elements, leaving vacant sites in the space lattice. Magnetic separators are used to beneficiate a wide variety of industrial minerals. In this application the relatively large volumes of nonmagnetics are usually the commercial products. The amount of mag-

Jan 1, 1959

By Mario Aiezza

This paper outlines the results of a relationship developed during the design and construction of the foundations for the Gallery Towers project in Melbourne. Both the builder and the piling contractor were determined to arrive at a satisfactory foundation solution to the problems encountered at the site. The scope of piling work was to provide load-bearing piles under the building columns, some of which were located within a retention system that also required a piling solution. Geological conditions were variable and challenging. The site area was small and located adjacent to the National Arts Centre in the developed Southbank area, a high density office area. This presented logistical problems in limiting construction traffic on site and also demanding minimal noise and vibration emanating from piling activities. The piling contractor, Vibro-Pile, and the builder, Walter Construction Group, faced the challenges presented with a refreshing cooperative attitude that was beneficial to both companies. Commercial issues rising from design and construction problems were first put apart in order to allow the respective technical department of each company to work with minimum constraints to achieve the most cost effective solution. In the process usual adversarial attitudes resulting in loss of time and money was avoided. A number of issues were addressed successfully at minimum cost and time during this contract. Despite the difficulties encountered, the job was completed on time and with negligible claims for extras, resulting in the development of a strong mutual respect between both companies.

Jan 1, 2002

By A. R. Guest, R. Clayton, J. Jakubec

"The potential for mudrushes is a potential hazard that should be evaluated during cave mining studies. Mudrushes are a phenomenon that can have very different origins, but produce the same results: injury, loss of life, damage to property, excess dilution, production delays, or mine closure. Although mudrushes are more common in cave mines than other mines, any mining activity that enables the accumulation of fine particles and water is susceptible to mudflow. This paper describes the process developed by the authors during the past decade to evaluate the risk of mudrushes, specifically in caving and sublevel caving mines.RÉSUMÉ Un danger potentiel qui devrait être évalué durant les études d’exploitation par blocs foudroyés est la possibilité d’afflux de boue. Le phénomène des afflux de boue peut avoir des origines très diverses; les résultats sont cependant les mêmes : des blessures, des pertes de vie, des dommages à la propriété, une dilution excessive, des délais de production ou des fermetures de mines. Bien que les afflux de boue soient plus fréquents dans les mines exploitées par blocs foudroyés, toute activité minière qui permet l’accumulation de particules fines et d’eau est sujette à des coulées de boue. Le présent article décrit le processus développé par les auteurs au cours de la dernière décennie pour évaluer le risque d’afflux de boue, surtout dans les mines exploitées par blocs foudroyés et par sousniveaux foudroyés."

Jan 1, 2016

By J. H. Adkins

The purpose of this research is to identify hazards associated with roof bolting and to make recommendations for procedural and equipment design changes to reduce those hazards. To that end, the project reviewed Literature on related research, collected and analyzed roof bolting injury data, normalized the injury data be exposure time to each activity and identified problem areas within the root bolting tasks. In addition, field data collection forms were prepared and mines selected for field work. In the field, observations were made of eighty (80) different roof bolting crews bolting one hundred fifty-five (155) place;, on forty (40) sections spread among nine (9) mines. Task analysis forms were used to record unsafe behavior or conditions for each crew and each place. Informal discussions were held with the mine's safety and training officer, the maintenance officer, one section foremen and, when possible, the observed crew, concerning the training and experience of the miners. Unsafe acts were categorized and related to the "Activity While Injured" categories developed during the accident analysis. For each of these categories one or more recommendations for corrective measure, machine modification, procedural change or job training were developed. The study produced over fifty (50) specific recommendations involving machine design, procedural, safety training and supervisional issues that would lead to reduced roof bolter injuries in the near term. The authors concluded, however, that only the development of truly hands off/remote bolting can eliminate or reduce to an absolute minimum the hazards to which the roof bolter is subjected.

Jan 1, 1977

By Richard D. Begley

This paper summarizes the development of a mechanistic model to predict longwall mining induced surface subsidence. The model was originally developed from data acquired from a recent field study conducted in Northern West Virginia. Additional data has been collected from published sources and used to refine the model. The original model utilizes a negative exponential equation to predict the subsidence profile after the maximum possible subsidence is predicted based on the following input parameters: mine geometry, angle of draw and expansion factors for the deformation zones that have been identified above a longwall excavation. The model refinement involved the development of relationships between physical properties of the overburden strata and angle of draw in addition to the expansion or bulking factors. Therefore the refined model now requires only mine geometry and a typical geologic column from the site to predict the subsidence profile. This paper provides the methodology that enables the model to determine the angle of draw and expansion factors breed on physical properties of the site geology i. e. percent of strong rock and Rock Quality Designation of the overburden strata. In addition :comparisons of predicted results with measured data for over H) different sites with various geological and geometrical parameters located throughout the United States will be presented.

Jan 1, 1989

A description is given of the construction and operation of an automatic version of the coarse batch particle sizer which requires a minimum of operator supervision and which is capable of processing a sample every 4 min.

Jan 1, 1968

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

By J. F. Jackson, R. W. Mau

"The first commercial installation in the mineral industry of the ""Verti-Press"" pressure filter was made by Falconbridge Limited at the Strathcona Concentrator to filter copper concentrate. The filtercake produced contains 6 - 7% H2O, an improvement from the 12 - 13% H2O produced by an internal drum filter, at rates of up to 20 t/hr. A novel slurry feed system incorporates a hose pump and a pressurized slurry accumulator.INTRODUCTIONIncreased copper production from Falconbridge Limited operational mines in the Sudbury Area has exceeded the current refinery capacity. A copper concentrate has been produced to overcome this constraint and has been shipped to custom smelters either as a slurry or as a 12 - 13% moisture filtercake utilizing an internal drum filter.With the treatment of the new Deep Copper Zone from the Strathcona Mine, copper concentrate production was forecast in excess of the installed dewatering capacity. The filtercake was too wet to transport by truck and the custom smelter refused to handle this product at the truck unloading site. The filtercake had to be trucked to a rail spur and transloaded into gondola cars. This system was expensive, incurred unaccountable losses and the concentrate was assessed a moisture penalty.To reduce the concentrate moisture content to permit direct shipment by truck, two basic systems were available; vacuum filter followed by a thermal dryer or a pressure filter. Past experience with the high capital and operating costs of dryers led Falconbridge to closely examine the pressure filter alternative.COPPER CONCENTRATE PRODUCTIONThere are two separate circuits at the Strathcona Mill; one treating nickel ore and the other treating copper ore.The rougher concentrates produced by both circuits are conditioned with lime and cyanide before the copper-nickel separation in a flotation columns. The concentrate consisting of cha lcopyrite with mi nor cubanite is very clean as shown in Table I. Currently 50% of the copper in the plant feed reports as copper concentrate, in the past, this has been as high as 70%."

Jan 1, 1990

The Direct and Indirect Effects of the Reagent Suite on Froth Stability in Laboratory Scale Batch Flotation Tests

Sep 13, 2010

By Steven Norris, William Moler, Michael Cole, Patrick Doig, Debi Lewis, Craig Pyle, Matthew Crow

The recently completed Lower Northwest Interceptor Program (LNWI) in Sacramento, California comprises, ten pairs of micro tunnels totaling 4,369 m (14,417 ft),three horizontal directionally drilled bores totaling 956 m (3,154 ft), and two large diameter tunnels under the Sacramento River totaling 1,198 m (3,953 ft). This paper briefly summarizes surface and subsurface conditions, and planning and design considerations. It then goes on to describe problems encounterd with each trenchless crossing, as well as lessons learned with respect to shaft construction, ground control at shafts during tunnel break-in and break-out, frac-out and heave, settlement, obstructions, coordination with permitting agencies, and application of geotechnical baseline reports.

Jan 1, 2007

By Richard H. De Voto

The McDonald gold project and two satellite gold deposits near Lincoln, MT were discovered in the early 1990s. They contain at least 307.9 t (9.9 million oz) of gold and 933 t (30 million oz)of silver. The McDonald gold deposit alone contains 223.9 t (7.2 million oz) of gold reserves that can be open-pit mined and processed by cyanide heap leaching at a projected cash operating cost of $6.10/g ($190/oz). The deposit is predominantly oxidized with no chance of acid production. It can be mined, operated and reclaimed with minimal permanent environmental disturbance other than the creation of an open-pit filled with a fresh-water lake that would support trout.

Jan 1, 2000

By Poltak Sinaga

PT Kaltim Prima Coal?s 13.1 km overland conveyor (OLC) was commissioned in 1991. It is of conventional 3 roller 350 trough belt type. Cost and performance optimization during initial design ended up with 5.4 mps belt speed, 1000 mm belt width to convey 1350tph, and 7 mtpa of coal. Despite high initial figure, the belt speed was lifted to 6.5 mps in 1996 to accommodate mine throughput increase. In 2002, new low loss ST2100 1100mm wide belt replaced the old ST2250 due for change-out. An upgrade project was initiated at the end of 2003 to further increase the belt speed to 8.5 mps, hence to increase the OLC capacity to 30 mtpa (million ton per annum). Performance data, experience of site personnel, site observation and tests, benchmarking, and information from equipment manufacturers were major inputs to the design review. The project fast track was another challenge in addition to executing modifications on a production lifeline. The project was completed within fifteen months and the OLC was successfully commissioned at 8.5 mps belt speed in February 2005. The OLC has been to date conveying 4 200 tph satisfactorily.

Jan 1, 2008

By Lebeau M., P. Duguay

"The cost of occupational injuries and diseases in the mining industry in Quebec was estimated for the period of 2010 to 2012. The method used takes into account the financial and human costs assumed by employers, workers, and the community. To better direct research and prevention toward issues with the most significant consequences, the results are presented in various ranking tables, which stakeholders might find useful.RÉSUMÉ Le coût des accidents du travail et des maladies professionnelles dans l’industrie minière au Québec a été estimé pour la période 2010-2012. La méthode utilisée prend en compte les coûts financiers et humains endossés par les employeurs, les travailleurs et la communauté. Afin de mieux orienter les recherches et la prévention vers les problèmes ayant les plus graves conséquences, les résultats sont présentés dans divers tableaux de classement, qui seront d’une grande utilité aux parties prenantes. INTRODUCTIONThe mining industry is much safer today than it was 30 or 40 years ago, mainly due to a more qualified workforce, the use of automated equipment, and a corporate culture more focused on occupational health and safety (OHS); however, the number and the severity of occupational injuries and diseases continue to make this industry one of the most hazardous. In the province of Quebec, the mining industry accounts for approximately 0.4% of paid workers but is the source of 4% of fatal work accidents. It is, therefore, important to continue the prevention efforts already underway in the mining industry.The difficult global economy, which has affected the mining industry in the last few years, is an opportunity to reaffirm that sound management of OHS can have a positive impact on companies’ productivity and profitability. Occupational injuries and diseases are costly for the companies concerned and for society as a whole. Reducing their occurrence makes it possible to reduce not only the size of workers’ compensation board contributions but also several other financial and human costs."

Jan 1, 2018

By Jim Rozek, Robert A. Gee

The Epping to Chatswood Rail Line project is the largest publicly funded infrastructure project in New South Wales. Construction commenced in November2002 with opening scheduled for 2008. The work includes 13 route km of twin TBM driven 7.2 m diameter lined running tunnel, three cross-overs and three new underground stations. The new stations have platform caverns of 20m span with similarly proportioned concourse caverns alongside. The ground is bedded sand stone and shale with high horizontal stresses. Predicted stress-relief induced ground movements during staged excavation led to innovative use of rock anchors for permanent support.

Jan 1, 2005

By Norman O. Lotter

Drill core is preferred as the sample material for metallurgical and mineralogical characterisation and flowsheeting of an orebody. The question arises as to how to do this at the economic optimum, since geologists have several other strategic uses for their drill core. The limiting factors are the cost of extra drilling for the metallurgical testwork and the need to preserve the drill core record. In this study, the representative sampling of drill core at an economic optimum for metallurgical testing is addressed. This phase of the drill core work is preceded by earlier drill core characterisation - for which other appropriate sampling protocols are used - that has provisionally categorised the orebody into geometallurgical units. In stratified sampling of drill core, use is made of a version of the stratified approach to compound distributions proposed by Cochran in 1946. Use is made of Gy’s 50-piece minimum sample mass model to estimate minimum requisite sample mass. In the case where sampling and testwork are required on a Lifeof- Mine blend of a given ore deposit, whereby defined ore types or geometallurgical units are present, the sample mass requirement is significantly reduced by working from drill-core at the geometallurgical unit level. A case study using Raglan drill core is discussed. Using nickel as an indicator paymetal, and sampling at a fundamental variance level of 8%, the minimum sample masses for disseminated sulphides, net-textured sulphides, and massive sulphides are 3.80, 7.37 and 4.39 kg respectively. When the same drill-core is sampled as a Life-of-Mine mixture without knowledge of the geometallurgical units, the minimum sample mass increases to 84.28 kg. It is thus possible to assemble a representative Life-of-Mine sample of drill-core more economically, at the same time validating its representativity. Equivalent calculations for copper, platinum and palladium are discussed, with outcomes consistent with this finding. When all four paymetals are considered, one selects the largest minimum mass out of all four cases. This results in minimum sample masses of 11.67, 74.90 and 175.16 kg for disseminated sulphides, net-textured sulphides and massive sulphides respectively. The simulated Life-of- Mine blend would require a minimum sample mass of 377.33 kg to cover all four paymetals.

Jan 1, 2010

By Faruk Oksuz, Cary Hirner, William A. Rochford

Grouting is a frequently utilized remedy in the planning and implementation of ground improvement and tunnel rehabilitation practice. The state-of-art grouting application used for Chicago’s McCook Reservoir project offers a unique alternative to the tunneling industry for pre-excavation grouting as well as tunnel rehabilitation, rescue and post-excavation ground improvements. The McCook Reservoir project included a computerized grouting control and data collection system for a precise and highly effective groundwater cutoff in fractured dolomites. By using balanced and stabilized grout mixes, the effective permeability of the rock mass was reduced over two orders of magnitude to less than 0.1 Lugeon by installing a double line grout curtain. The stable grout mix designs allowed high pressure and effective grouting at depths up to 125 m (410 ft).

Jan 1, 2005

By Reed. Donald F.

"Deposits of gray hematite occur in two districts in Talladega County, Ala., the Emauhee-Tallasochatchee and Weewoka, both in the vicinity of Winterboro, 50 miles east of Birmingham.The deposits were investigated by the Bureau of Mines in 1943 and 1944. Approximately 13,000 feet of diamond drilling was done and 6,000 linear feet of trenches excavated and sampled.A total of 13,000,000 tons of ore averaging 36 percent iron was indicated in all areas.A detailed discussion of each property investigated, drill logs, and sampling results are given in this report.In the work done in the Talladega County iron investigation, special acknowledgement is due to Paul M. Tyler, formerly regional engineer, Eastern Region, and Richard W. Smith, formerly district engineer, for aid and direction of the project; also to J. B. Clemmor, metallurgist, for diligent research work in the Southern Experiment station laboratory. All were members of the Bureau of Mines Staff.The project was conducted in cooperation with the Federal Geological Survey, whose field work was in charge of T.G. Andrews assisted by Brewster Baldwin. The able and valuable assistance of Andrews and Baldwin aided greatly in accomplishing the project.The areas investigated by the Bureau of Mines were in two districts: The Emauhee-Tallaseehatchee district, between Sylacauga and Sycamoer (marked B on fig. 1) and the Weeworka district, between Winterboro and Sycamore (marked A on fig. 1)."

Mar 1, 1949

By W. G. Miller, J. D. Scott, D. C. Sego

ABSTRACT An overall study was conducted to evaluate the properties and processes influencing the rate and magnitude of consolidation for oil sands fine tailings produced using different extraction processes. As part of the overall study, a comprehensive description of physical and chemical characteristics of fine tailings generated by caustic and non-caustic processes was carried out. Ultimately, the influence of these fundamental properties on the compressibility, hydraulic conductivity and shear strength properties of the fine tailings was assessed. The characteristics of the fine tailings are presented in terms of index properties, mineralogy, specific surface area, water chemistry, liquid limits, particle size distribution and structure. A difference in water chemistry was concluded to be the cause of substantial differences in particle size distributions and degree of dispersion of the comparable caustic and non-caustic fine tailings. The degree of dispersion was consistent with predictions for dispersed clays established by the sodium adsorption ratio (SAR) values for these materials. A linear variation of increasing dispersion with increasing SAR up to a SAR value of about 40 has been suggested, above which fine tailings are completely dispersed. The observed dispersed or flocculated structures (viewed using a scanning electron microscope) supported the predictions based on SAR values.

Jan 1, 2010

By N. D. Policow, J. S. Orphanos

D.A. Dahlstrom In the paper, a comparison was made between flowsheets using the screen bowl centrifuge and disc filters, respectively, as the primary dewatering device. The authors very effectively show that by raising feed temperature, mechanical dewatering is enhanced through reduced viscosity of the water. When a final coal moisture of 10% is required, the net effect of heating the feed is a reduction in thermal requirements because of the lower evaporated load on the dryer. The flowsheet comparison on this, however, was not completely correct. Disc filters do not generally utilize enhanced mechanical dewatering through increased temperature. Horizontal belt filters, through the optimal use of steam heating of the filter cake, have shown significant cost reductions over disc filters where steam is not used. In addition, the authors forgot to mention that there is a certain fraction of the feed that is so fine that it cannot be recovered by the centrifuge economically. That is the function of the filtration device shown in Fig. 4. In subbituminous pipeline coals, this fraction represents more than 10% of the feed. Even after flocculation and belt pressing, the moisture content in the fine fraction is 30%-40. Recent tests on a subbituminous pipeline coal slurry, compared an Eimco-Extractor horizontal belt filter with the screen bowl centrifuge flowsheet shown in Fig. 4. Mechanical dewatering was enhanced through the use of a steam dry zone after the initial dewatering zone. Vacuum pump horsepower was reduced by more than 50% through the use of condensors, and heat recovery was utilized to minimize thermal costs. Thermal drying to 10% moisture by weight was required in both flowsheets. The 0.5 wt% fines in the filtrate were flocculated and recycled to the filter, thus eliminating the belt press and solids mixers. When the three major operating costs (which normally account for 50%-75% of the coal operating costs) of steam, electricity, and flocculants at current prices were calculated, the flowsheets utilizing the Eimco-Extractor had cost savings vs the centrifuge flowsheet of 89¢/t (81o; per st) of surface dry coal. This advantage increases with increasing thermal and electricity prices. I congratulate the authors for the strides made with the screen bowl centrifuge. However, filtration flowsheets continue to be improved and their simplicity and low thermal and electrical requirements should not be so quickly dismissed. ? Reply by N.D. Policow From a technical standpoint, a number of extensive test programs have demonstrated that by raising the feed temperature, mechanical dewatering is enhanced whether it be centrifuges or filters performing the separation. Economic constraints usually become the over-riding issue. If an inexpensive source of thermal energy is available, i.e., waste steam, etc., the approach becomes commercially acceptable. For the specific case of coal slurry pipelines, since the dewatering plants will be located close to power generation stations, the preheating approach becomes especially attractive. The cost comparison shown in Fig. 7, which was prepared by a major West Coast engineering firm, contrasted screen bowl centrifuges and disc filters. In both alternatives, a thermal dryer was specified to produce a contract moisture of the final product. Sizing of the thermal dryer on the screen bowl alternative was substantially smaller than that of the filter, since the screen bowl was credited with a four to six percentage point decrease in product moisture compared to the disc. This comparison was made at ambient temperatures and reflected solely the mechanical dewatering capabilities of the two devices. No preheating of the feed was included in this particular comparison. Early generation screen bowl centrifuges operated under the principle of maximum bulk tonnage throughput. Second and third generation machines have followed the trends dictated by the coal industry calling for higher one-pass recoveries than previously demanded. The current generation of high-speed, long-bowl centrifuges permit recoveries of ultrafine solids directly comparable to commercial filter operation. On typical coal preparation plant feeds with nominal 600 E. an X 0 (28 mesh X 0) clean coal, recovery levels in excess of 99% are now obtained. The material that does escape the centrifuge and reports to the main effluent is typically -10 µm, high ash material. We have documented substantial beneficiation effects in screen bowl centrifuge performance with the cake product containing lower ash levels than the feed. On the referenced pipeline, coal tests performed on Western subbituminous coal, we found that the percentage of -10 µm material in the feed was six to eight times greater than normally encountered on eastern Appalachian seams. Our 45-t/h (50-stph) production centrifuge was never set up to maximize recovery. It was used as part of the two-stage dewatering circuit that had been chosen by designers of the proposed pipeline. Recoveries up to 95% were recorded. With field adjustments, that performance could most certainly have been improved. In contrast, manufacturers of the horizontal belt filter provided a small pilot-scale unit that operated on a side stream at the test facility. Numerous combinations of chemical additions were evaluated to determine those that had the best impact on filter performance. Whereas the screen bowl centrifuges operated without chemical addition, producing a dry, fluffy cake, the belt filter required two stages of chemical addition to attain satisfactory performance and high recovery levels. On the two-stage circuit that incorporated a belt press as the secondary

Jan 12, 1983