Search Documents

By S. L. Windes

"INTRODUCTION For a number of years, the Bureau of Mines conducted tests on various types of structures to ascertain the effect of seismic vibrations emanating from quarry blasting in an effort to determine an index of damage. Associat¬ed with these tests, occasional records were made of the characteristics of the air blast or concussion from the explosions. Although the importance of the air-blast problem was recognized, the equipment was not designed for airblast measurements, nor was the early research program concerned with the problem. After the ground-vibration tests had been completed, attention was turned to study of the air blast and its effect. The program was modified, however, in certain aspects by the imminence of war and the final entry of the United States into the conflict. These modifications were made to supply information pertaining to military and civilian defense problems.Detailed discussion of these problems is beyond the scope of this report, which attempts to present preliminary results of factual and fundamental character. However, it may be noted that airblast data are urgently needed for intelligent design of both Government and non-Government buildings, which must withstand the air blast from bombs and afford maximum protection for the occupants. The safety of vital equipment above and below ground necessitates consideration of damage from air blast. Protection against use of dynamite by saboteurs, moreover, hinges largely on the effect of air blast. Identification of a planned ""accident"" involving dynamite often entails knowledge of the characteristics and power of the airblast.The peacetime problem of damage from air blast resulting from quarry and mining blasting activities is of course exaggerated by the wartime requirements of increased production accelerated operation, and enlarged development."

Jun 1, 1943

A tectonic interpretation of the Coromandel Peninsula which suggests that the basement underwent tensional collapse at its northern and southern ends would permit more ready penetration of late stage magmatic fluids. This hypothesis is consistent with regional trends of the chloride content of low grade geothermal waters and of the yield of gold and silver per unit weight of quartz worked. The consequences of such a model are that mercury should not only be a good pathfinder for Coromandel gold, but that it should be correlative with ratios of base metals high in the zoning or paragenetic sequences to those lower in the sequences. This is demonstrated successfully in an area of mineralisation in the southern Coromandel.

Jan 1, 1987

By N T. Moxon, L W. Armstrong

Explosive manufacturers have for many years provided a service to the mining industry which has,until recently, been unchallenged by mine operators. Today mine operators are more aware of the properties of explosives required to perform particular tasks within their operations. These properties can be reliably quantified using the test procedures described in this paper for emulsion adn ANFO based explosives. Details of an end-user sampling programme desgined to provide quality checks on explosives supplied to a mine site are also discussed.

Jan 1, 1991

By Joseph M. McCann

The Brightwater regional wastewater treatment facility, under construction in King County, WA, includes an extensive conveyance system that will feature deep, soft-ground tunnels and shafts. Excavation of the Ballinger Way Receiving Portal to 65.8 m (216 ft) below grade through challenging geology was accomplished by means of artificial ground freezing. This paper discusses freeze design development, system installation and monitoring, and the contractual and construction challenges that were overcome, including work sequencing and excavation means and methods, together with lessons learned.

By Larry F. Drolet

Charleston, SC is anything but boring. The city was founded in 1670 and has played a significant role throughout the history of the United States. Located along the coast of the Atlantic Ocean in the southeastern United States, Charleston was a vital city in America?s early existence. Charleston?s coastal location has helped the city become the fourth largest cargo port in the United States and earn the 2011 designation as the number one travel destination in the United States by the Conde Nast Traveler Magazine. Part of Charleston?s charm and beauty can be attributed to its historic structures and churches that line nearly every sidewalk, roadways that were laid out based on the width of horse carriages, great weather, southern hospitality and coastal living. Now imagine the challenges of installing new, or re-placing aging infrastructure, in this setting. Every shovel full of dirt, every stick of pipe and every roadway sub-surface has its own historic story to tell. For engineering minded individuals, Charleston?s infrastructure has almost as fascinating a history as its more visible surface structures. Charleston was among one of the first American cities to construct separate sanitary and storm water drainage infrastructure. This concept has roots dating back to the city?s founding and is a credit to the foresight of its founding fathers who understood the basic health differences between sanitary and storm water.

Jan 1, 2013

The only economically significant deposit of dolomite in New Zealand is at Mount Burnett, in north-west Nelson. The dolomite, associated with marbles and schists, is complexly deformed, and is of Paleozoic age.A very large quantity is present, although the recoverable amount is to some extent limited by the difficult terrain.Physically the quality of the dolomite is excellent. It is a tough, durable, fine grained rock. Chemically it is a little more variable. The range and frequency o~ the more important impurities are illustrated by hlstograms, as is the "dolomite factor"-a measure of the amount of the mineral dolomite in the rock. lbe dolomite factor averages 84 per cent, the remainder of the rock consisting largely of calcite. Quarrying, milling, production, and uses are described. In 1966 production reached 13,250 tons.

Jan 1, 1969

By J. Matos e Silva

"Abstract The paper refers five examples of executed diaphragm walls with one to five levels of anchorages. For each example a comparison is made between the results of the design using the traditional criteria and the ones obtained by using the Eurocode 7 and the Portuguese Norm related to the EC7 (NP EN 1997-1 2010), as the Eurocodes consider the possibility of each European country to adopt their own geotechnical parameters as these may vary from one country to another. A comparison is also made with the behaviour of these diaphragm walls during its construction phase; so the values from the design that were adopted in the construction are listed in tables 2 to 6 in the “Construction Options” columns. From the referred examples the author presents his conclusions.1 - INTRODUCTIONIn the so-called “traditional criteria” the soil parameters (dry unit weight, angle of internal friction and cohesion) have values obtained through tests or empirically. It is assumed that the characteristic values of the soil parameters adopted in Eurocode 7 are equal to the soil parameters adopted in the calculations by the “traditional criteria”. In the present paper the design according to the EC7 was made considering only the ultimate limit states and the respective Cases A1 and A2.The partial coefficients used for the actions in the present paper were those on Table 1:2 - CONSIDERED EXAMPLESThe five examples correspond to the situations of figures 1 to 5, and the respective results are summarized in tables 2 to 6.For all the considered examples, that are case histories, a simplified method published by Matos e Silva (March 2000) was adopted. This method attains good performances when compared with other more sophisticated ones as the finite elements and the elasto-plastic methods as described in a paper published by Matos e Silva (2000). All the obtained values were compared between them and with the so-called “Construction Options” that were the values adopted by the designers of the considered examples. For the wall bottom length calculation two possible situations were envisaged:"

Jan 1, 2014

By I. S. Blair

The introduction of the 36 MVA smelting furnace at Mufulira, and the experience gained during the first five years of operation have been described previously (6). Based on this experience the furnace was rebuilt in 1977., Details of the modifications made during this rebuild are described. Subsequent to the rebuild, refractory failures, particularly in the electrode ring bricks of the sprung arch roof, continued to cause concern, and repair and improved roof control methods are described. Electrode breakages continued, but developments in casing design and electrode preparation have resulted in significant improvements. Modifications in the electric furnace gas handling system are outlined, together with details of further changes to be implemented in the near future. The systems developed for metallurgical control of the furnace and the thermo-dynamics of the process are discussed. The electric furnace at Mufulira is now operating at above design production levels, and has decisively justified the choice of this technology in situations with inexpensive electric power. The potential for further increases in production capacity from the Mufulira unit, and improvements in design for new units are discussed.

Jan 1, 1983

By W. Collingwood

As open pit mines continue to grow deeper and productivity continues to increase, the management of respirable dust and noxious gases can become a challenge. The natural wind flow in open pit mines is often recirculatory. This recirculation traps dust and gases in deep open pit mines. This problem is particularly acute in high latitude open pit mines due to a phenomenon known as an atmospheric inversion. In the winter, arctic and subarctic regions experience short days and long nights. This deficit of solar radiation creates a situation in which cold, still air accumulates near the bottom of the pit. In open pit mines, this can result in unhealthy accumulations of gases and other contaminants in the open pit mines. In this study, the natural wind flow patterns in and around open pit mines were investigated using a computational fluid dynamics (CFD) program. Two dimensional models were created for a variety of pit geometries. The effect of depth, slope angle, and wind speed on the recirculation pattern in the pit was examined.

Jan 1, 2011

By W. M. Dressel

This Bureau of Mines report describes a shaft closure demonstration project in which 11 inverted pyramid-shaped plugs were used to plug abandoned open mine shafts in Galena, KS, The inverted pyramid-shaped forms, fabricated from steelplate, were designed so that the inverted base would be larger, by 4 ft on a side, than the approximate size of the shaft opening at the surface residuum-solid rock interface. After the surface openings of the shafts were trimmed with a backhoe, the steel forms, complete with reinforcing, were lowered into the openings and filled with concrete; the remaining portions of the openings above the plugs were backfilled to slightly above the surrounding surface level with waste rock and soil. Location and elevation monuments were installed for long-tern evaluation of the success of the project.

Jan 1, 1985

By H. B. Humphrey

[EXPLOSION of gas and dust in coal mines, have caused death t lid injure to mines, and destruction of workings in all countries where coal is mined underground. In the United Stales the first reported explosion wits in Min; explosions have continued to the present. The danger to film ill it mine When an explosion occurs in not always measured by the violence created or by their nevi lies, to the area through which flame and Violence extend. As many, perhaps more, risen have died from gases and lade of oxygen (known as "after-damp") than have been killed by the blast and hart. Me explosions often are caused by it combination of factors, including concentration of methane in air, formation of clouds of dust, and the presence of a flame or spark. These explosion factors have varied with changes ill milting method and practises over the years, but the basis causes have always been the salve. Understanding of the causes and to acceptance of ways to guard against explosions and their effects have been slow to spread from investigates to officials and Own to bosses and miners. To a considerable extent there hats lawn a belief that explosions were a joining risk but might hr, put oil hut could not be presented. Such belief is based on the human failure to maintain and observe necessary precautions. These failures, caused by inertia to change, carelessness, or reliance on continuance, of past explosion-free years, are being reduced in number and effect by education of miners and supervisors and acceptance of higher prevention standards.]

Jan 1, 1959

By Dennis Nottingham

Spin-fin pipe piles can develop large loads in tension, thus have evolved as a foundation product of great potential. Currently, over 500 spin-fin piles have been used successfully in dolphins, docks, buildings and bulkheads. Spin-fin piles are pipe piles with plates welded near the tip at a batter-in-screw fashion. Thus, as the pile is driven, the pile screws into position. Tests show this pile type to have highly unusual stress/strain relationships, wherein plunging failure is usually never reached either at normal or large deformations. Tension capacity can approach pile capacity in bearing; thus, large reserves are usually available for tension. Tests have been performed on 8-5/8-inch to 24-inch-diameter piles in silt, sand, and gravelly soil, to provide a broad spectrum of data.

Jan 1, 1990

By Brooke T. Mossman

Asbestos fibers are highly fibrous silicate fibers that are distinguished by having a large aspect (length to diameter) ratio and are crystallized in an asbestiform habit that causes them to separate into very thin fibers or fibrils. These fibers are distinct from nonasbestiform cleavage fragments and may appear as thick, short fibers which break along cleavage planes without the high strength and flexibility of asbestiform fibers. Since cleavage fragments of respirable dimensions have generally proven nonpathogenic in animal studies, little data exists on assessing well-characterized preparations of cleavage fragments in in vitro models. The available studies show that cleavage fragments are less bioreactive and cytotoxic than asbestiform fibers. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestiform; Cleavage; Fibers; Fibrous

Jan 1, 2007

By W. R. Hardwick

This information circular describes open-pit mining methods and practices of the Bagdad Copper Corp., Yavapai County, Ariz. It is one of a series being prepared by the Federal Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. A brief history of the Eureka district and of early developments at the [gdad] mine is given, and the are deposit is described with particular emphasis on those characteristics (physical, economic, or engineering) that affected the choice of mining methods. Prospecting, exploration, and sampling and estimating the tonnage and grade are outlined. Development of the open-pit mine is shown. Mining methods, including breaking ground, primary drilling and blasting, secondary drilling and blasting, loading, transportation, engineering, and operating control, are described. A brief summary of mining equipment is given. Percentage of extraction, production rate, mine drainage and water supply, wage, contract, and bonus systems, safety and fire prevention, and the processing plant also are described. The last section gives a breakdown of such costs as are available for publication.

Jan 1, 1959

By S. du Plessis

Nationalization is high on the policy agenda in South Africa. This paper considers the case for nationalizing the local mining sector from an evidence-based perspective, which is derived from theoretical considerations and related to the known features of the South African mining sector and economy. A strong case against nationalization emerges, which can be summarized as follows. The mining sector is competitive and therefore a poor candidate for public ownership. Furthermore, the resources sector does not dominate the South African economy nor does it create the risk of a decrease in the competitiveness of the industrial sector via the unintended adverse impact of an appreciating real exchange rate due to a commodity boom (Dutch Disease). Nationalizing the mining sector will cost the government more than it receives. This is not only a bad idea in itself, but it will limit the scope for distributive policies on the national budget. The contemporary international experience demonstrates the risks of fiscal imprudence. Finally, nationalizing the resources sector will undermine support for those very market-based institutions required to achieve a higher long-run growth trajectory.

Jan 1, 2013

By Hayward SB, First DM

The Maragorik Prospect represents a partially eroded Pliocene acid sulphate style epithermal gold system hosted within the Sigule Volcanics and Riet Bed sediments which is inferred to have formed from a degassing porphyry body at depth. A regional sinistral rotation provided by transform faults associated with the opening of the Manus Basin imparts a dilational character to mineralised NE trending faults formed parallel to the Warangoi Graben. A controlled-source audio magneto-tellurics (CSAMT) survey has identified E-W trending buried conductors which may represent alteration formed within dilation zones. While some gold mineralisation occurs within vuggy silica at Palang Hill, the target is auriferous enargite (luzonite)-bearing breccias from the LK1 and Gureki areas.

Jan 1, 1991

By Madan M. Singh

The use of fluid jets for industrial purposes has received considerable attention in recent years. The convening of The First International Symposium on Jet Cutting Technology1 in April 1972 devoted solely to this subject probably heralds the coming of age of this new science. It is interesting to note the emphasis in the conference towards the cutting of rocks, minerals, and soils, indicating the attention being devoted to excavation and mining. The use of water streams for mining of minerals is not new. It is well over a century since its first application.2 But its use in coal mining has been somewhat restricted over the years. In the past 30 years the U.S.S.R. has successfully used water for coal extraction, and these techniques have been examined in 15 countries in recent years. In the United States research on various aspects of the method has been conducted for over 15 years,3 but success stories from the Soviet Union,4 JapanS and Canada6 in the last 5 years has spurred greater enthusiasm. IIT Research Institute has done pioneering work in the 7-12 13-15 area of water jetting for rock and coal breakage. It has just completed an experimental study involving mining of coal with a 50,000-psi and 100,000-psi jet in a stripping operation14 under the sponsorhip of the U. S. Bureau of Mines (Contract No. HOll1789). As a complementary program the Bureau initiated a project to design a water-jet coal-mining machine (Contract No. H0133119). IITRI was a successful bidder on this competitive procurement.

Jan 1, 1974

By W. E. Wells

This report describes experimental investigations made in the batchwise retorting of Colorado oil shale. Three heat-carrying mediums were used -hot shale gas, superheated steam, and hot flue gas. Using hot Shale gas for retorting, the several variables studied were retort-inlet-gas temperature, gas velocity through the shale bed, shale particle size, and grade of shale. In studying the effect of any one of these variables on oil yield, as and operability, the other variables were maintained essentially constant. Oil yields decreased with increasing in-let-gas temperature and increasing shale-particle size, and oil yield increased with increasing grade of Shale up to 50 gallons of oil per ton of shale, beyond which the process was inoperable because of swelling and caking of the shale during retorting. Changes in gas velocity had little effect on oil yield. Gas yield increased with increasing inlet-gas temperature, gas velocity, particle size, and shale grade. Oil yields of 100 percent of Fischer assay and from 1,600 to 1,800 cubic feet of 300-B.t.u. gas per ton of shale were obtained. Two runs only were made using superheated steam. Oil yields averaged 97 percent of Fischer assay, and gas yields averaged 4,00o cubic feet per ton of shale. Retorting with a hot flue gas produced from combustion in the shale bed, as in the N-T-U process, gave excellent yields using closely sized shale with recycling of flue gas. An excess of fine shale in the charge resulted in channeling and low oil yields. Using no recycle gas, good yields were obtained that tended to decrease with increasing air rate, and the retorting rate increased with increasing air rate over the range studied. Coking was not found serious with 30-gallon shale at the air rates used.

Jan 1, 1952

By A. Mboma

Keywords: Furnace, decommissioning, care and maintenance, re-start, funding, nickel Bindura Nickel Corporation (BNC) operates two nickel mines, and treats concentrates from these mines as well as toll concentrates from the region around its Bindura Smelter and Refinery (BSR) complex. At the smelter, concentrates of at least 5% nickel content are blended and dried to 4% moisture in a coal-fired rotary kiln. Matte smelting of concentrate is carried out in a six-in-line electric arc furnace, where the furnace slag is granulated and discarded. Furnace matte is transferred via ladles into Peirce-Smith converters, where, after granulation, a leach alloy containing 68%Ni, 20%Cu, and 6%S is produced. Converter slag is recycled via the matte-smelting furnace. The onset of the global economic recession towards the end of 2008 resulted in a collapse of metal prices, worsening the local situation that was already marred by unfavourable macro-economic conditions in Zimbabwe. As a result, BNC mines were put on care and maintenance in November 2008, followed by Bindura Smelter and Refinery in February and March 2009 respectively. The business environment has since changed, and BNC is getting ready to re-start the plant. This paper describes the decommissioning of the Bindura furnace, asset preservation during the care and maintenance programme in the past two years, and preparation for starting up of the Bindura smelter in the near future.

Jan 1, 2011

Pipe Flow Stability of Concentrated Coal-Water Suspensions in the Presence of an Electric Field

Sep 13, 2010