Search Documents

By J. S. Kennedy, M. M. Fine

"INTRODUCTION Barite is one of the major industrial minerals whose production has increased considerably in the last 10 years. In 1935 domestic production of barite was 218,075 tons and. had increased by 1944 to 515,136 tons. 3/ Most of the primary uses for barite and barite products were developed before 1935, so the increase in barite production reflects the growth of industry in general rather than any recent developments in barite technology.The principal uses for ground and crushed barrite are as a weighting agent in heavy drilling fluids, as a filler in rubber and other materials, as a pigment and extender in paints, and as a flux in glass melt. In addition, a considerable' quantity of barite serves as the raw material for the manufacture of lithopone and barium chemicals.Specifications for barrite vary widely and depend primarily on the use to which the material is put. The primary requisites for barite used in heavy drilling muds -are that it have a minimum specific gravity of 4.2 and be very,low in soluble salts. A minimun barium sulfate content of 92 percent may be specified; but this is less important than the gravity. 4/ In addition before consumption the material must be ground to '92 percent minus 325-mesh. 5/ Lithopone and chemical manufacturers require a minimum of 94 Percent barium sulfate, a maximum of 1.0 percent iron oxide, and not more than a trace of fluorine. 6/ Barite used as fillers in light-colored products should be of fairly high grade, but the filler used in dark products may be considerably lower grade.Glass barite should contain a minimum of 96 percent barium sulfate, not more than 3 percent moisture, a maxium of 0.2 to 0.4 percent iron oxide, and not more than a trace of titanium oxide. Particle size is a matter of some importance in glass barite, also. 7/"

May 1, 1948

By M. Moagabo

CO2 emissions from carbonate laden reclaimed mine spoil has been shown to pose a hazard to residents in homes built on or adjacent to such land. The objective of this project was to develop a soil CO2 flux survey protocol for assessing reclaimed mine land. The research involved CO2 chamber accumulation flux surveys; stable carbon isotope ratio analysis; statistical hypothesis testing to examine correlation between CO2 flux and soil temperature and moisture as well as spatial dependence; and geostatistics to map CO2 and delineate high flux zones. Soil temperature was observed to have a positive correlation with fluxes while soil moisture was observed to be negatively correlated. Spatial dependence of CO2 fluxes on reclaimed mine land was observed on one of the two study sites. The research suggests that macro-porosity and gas permeability may be important factors that explain CO2 migration in mine spoil. A flux survey protocol has been developed, based on these results, for reclaimed mine lands. The work demonstrates the capability of geostatistical methods to delineate high flux fields. Further research will be required to determine suitable thresholds for such analysis.

Jan 1, 2012

By R. K. Sinha, B. S. Choudhary, Desh Deepak, A. K. Mishra, Hemant Agrawal, Shankar Kumar

There are several methods (empirical, statistical, and machine learning tools) to calculate blast-induced ground vibration. Still, due to complications in the blasting procedure, under varying blasting loads and strata conditions, it is not easy to predict and simulate blast vibration precisely. Therefore, a study was conducted to simulate the field blast data in Ansys software using explicit dynamics. For this study, monitoring of ground vibration for 20 single hole blasts was carried out. The density of emulsion explosives was in the range of 0.9 to 1.15 g/cc. In the laboratory, rock properties were determined from the rock sample collected from the mine site before blasting. The in-hole velocity of detonation (VoD) and the density of the emulsion explosive were also determined. These parameters were used for numerical analysis to know the ground vibrations at specified points. The results of ground vibration predicted by the model are validated using field data.

By J Pric, M Fulton, C Xia

A cyanidation study was conducted on a mild refractory gold ore sample from the Central zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. Gold, at a grade of 8.00 g/t, is present as native gold, electrum and aurostibite. The ore also contains 2.8 per cent pyrrhotite, together with several antimony minerals (0.8 per cent berthierite and gudmundite, 0.18 per cent native antimony and stibnite). It also exhibits weak preg-robbing properties with 0.16 per cent organic carbon. Aurostibite, a gold antimony compound, is particularly known to be insoluble in cyanide solution. The antimony dissolves in cyanide solution to form antimonates, which retards gold dissolution. Industrial practice of extracting gold from aurostibite generally consists of producing a flotation concentrate, which is leached in a pipe reactor at low alkalinity and high oxygen pressure with about 20 g/L cyanide. The proposed new approach is efficient and allows the extraction of gold directly from an ore at atmospheric pressure and a low cyanide concentration at pH 10.5. The effects of grinding, pretreatment, lead nitrate, kerosene and cyanide concentrations have been investigated. The maximum gold extraction obtained on the ore was 87.9 per cent using 800 ppm NaCN, 500 g/t lead nitrate, 30 g/t kerosene, DO 10 ppm and pH 10.5 in 168 hours. The associated cyanide consumption was 1.3 kg/t. The additions of lead nitrate and kerosene increased gold extraction. In comparison to a P80 of 74 ¦m, a P80 of 30 ¦m significantly increased gold extraction. Gold in solid solution in gudmundite and arsenopyrite was believed to be responsible for the unleached fraction until mineralogical analysis of hydroseparation concentrates of leach residues showed that most of the unleached gold occurs as aurostibite, either as locked grains in sulfides/sulfarsenides or as grains with passivation rims of an Au-Sb-O phase. Coarse gold was also found. Gold extraction was not sensitive to cyanide concentration from 250 ppm to 1200 ppm NaCN and high pH was detrimental. Decreasing the cyanide concentration reduced the cyanide consumption to 0.85 kg/t. The removal of coarse gold using a Knelson concentrator and a Mosley table prior to leaching increased the gold extraction to 90.4 per cent (leach residue at 0.77 g/t).

Jan 1, 2007

Baja Mining is currently constructing the Boleo metallurgical plant in Santa Rosalia, Mexico to recover copper, cobalt, zinc and possibly manganese products from the Boleo ore. The process involves an acid seawater leach of the whole ore followed by solid-liquid separation and washing of the leach residue. Solvent extraction is used to separate copper, cobalt and zinc from solution. Copper and cobalt are recovered as cathode metal products and zinc as a zinc sulphate monohydrate. Manganese may be directly precipitated as manganese carbonate which can be used as a feedstock for manganese metal production. Laboratory testing has continued to refine various aspects of the process including iron removal, cobalt and zinc solvent extraction, cadmium cementation, cobalt electrowinning and manganese metal electrowinning. The results of this testing are reported in this paper.

Jan 1, 2012

By M. C. Bétournay

Strainbursts are common in overstressed brittle rock around deep mine openings. Such failures are characterized by a biaxial state of stress in the plane of the opening boundary. A zone of compressive stresses imposes initial failures near or at the surface of the opening that results in spalling of thin slabs of rock roughly parallel to the free face. While the failure of rock under biaxial loading conditions is increasingly common in deep underground mines, only a few representative laboratory studies have been reported in the literature, without emphasis on rockbursting aspects, and none in the last decade. This paper presents the results of a testing program on a granite rock type. Biaxial testing, conducted on 100 mm cubic samples, was carried out to examine the influence of lateral confinement and loading rate on the rock’s ultimate strength. The paper reports the test results in terms of normalized biaxial failure envelope s1/sc-s2/sc. A discussion of the failure mechanisms observed is presented. Les coups de toits de déformations sont choses communes dans le rock cassant surcontraint en place autour des ouvertures minières profondes. De telles ruptures sont caractérisées par un état de contraintes biaxiales dans le plan de la périphérie de l’ouverture. Une zone de contraintes compressives impose des ruptures initiales à ou près de la surface de l’ouverture, qui produit des relâchements de minces plaques de roc plus ou moins parallel à la surface. Bien que les ruptures de roc sous des conditions biaxiales sont de plus en plus communes dans les mines à grandes profondeurs, il n’y a eu que quelques études représentatives en laboratoire de publiées, sans emphase sur des aspects de coups de terrains, et aucunes publiées depuis la dernière décennie. L’article présente les résultats d’une campagne d’essais appliquée à un type de granit. La campagne d’essais biaxiaux, sur des échantillons cubiques de 100 mm, avait pour objectif d’examiner l’influence du confinement latéral et le taux de chargement sur la résistance ultime du roc. Cet article fait part des résultats en terme de l’enveloppe de rupture biaxiale normalisée s1/sc-s2/sc. Une discussion sur les mécanismes de ruptures observés est présentée. Dehnungsbrüche findet man häufig in übergespannten spröden Felsen um die Öffnung von tiefen Minen. Solche Brüche sind von einer zweiachsigen Spannung in der Ebene der Grenze der Öffnung charakterisiert. Eine Zone von Druckspannungen verursacht initiale Brüche, entweder an der Öberflache der Öffnung oder in der Nähe. Davon scheiden sich dünne Felsplatten mehr oder weniger parallele mit der freien Wand. Obwohl Felsbrüche unter zweiachsiger Beanspruchung immer mehr häufig in tiefen Minen beobachtet sind, hat man über nur einige repräsentative Laborversuche in der Literatur berichtet. Diese Studien diskutieren das Thema ohne Betonung auf Felsbrüchen, und keine sind in den letzten zehn Jahren erschienen. Die vorliegene Arbeit gibt die Ergebnisse eines Testprogramms auf einem Typ von Granitfels. Durch zweiachsige Prüfungen von kubischen Proben mit Seitenlangen von 100 mm sollte man den Einfluss von seitlicher Ermittlung und der Beanspruchungsrate auf die Bruchfestigkeit des Felsen studieren. Man findet auch die Prüfergebnisse in bezug auf das normalisierte, zweiachsige Bruchkriterium s1/sc-s2/sc. Die beobachteten Bruchmechanismen sind auch diskutiert.

Jan 1, 2003

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By D. E. G. Maschmeyer

The operation of the pilot plant for the S-C Copper Process during 1976 has provided the basic data for the design of a commercial-scale plant. This paper introduces the commercial aspects of the S-C Copper Process through the presentation of a process flow diagram, a schematic flow diagram and basic design parameters for 75,000 tonnes per year (tpy) copper rod production from chalcopyrite concentrate. Basic operating requirements are outlined and a preliminary estimate of operating and capital costs for a Western Canadian location are summarized. The results have been compared with a modern smelter/electrorefinery to highlight the advantages and disadvantages of these two alternatives and to show why the new S-C Copper Process technology should be of interest to the copper industry.

Jan 1, 1978

By Stewart A. Silling, Dale S. Preece

The two key results of rock blasting are fragmentation and movement of geomaterials. Movement/flow of the blasted rock is often referred to as heave. Modeling the movement of full scale blasting is now possible with 3D distinct element models and parallel processing.

Jan 1, 2016

By P. den Hoed, R. I. Rambiyana

"Four sulphide minerals - pyrite (FeS2), pyrrhotite (Fe1-xS), pentlandite ([Ni,Fe]9S8), and chalcopyrite (CuFeS2) - contain the base metals and most of the iron in concentrates of platinum group metals (PGMs). In the pyrometallurgical processing of PGM concentrates these sulphides form a matte during smelting, and iron and sulphur are removed from the matte during the converting process. This paper discusses the roasting of Merensky concentrate in air before smelting, with the purpose of reducing the matte load to the converter.Roasting tests were conducted in a bench-scale rotary kiln at temperatures from 350°C to 700°C. The concentrate tested contained 17.4% sulphur and consisted of 23% pyrrhotite, 16% pentlandite, 11% chalcopyrite, and 2% pyrite. The particles were fine (d50 = 22 µm), and all the sulphide particles were liberated. Roasting in air at 550°C and 650°C for 20 minutes removed respectively 60% and 70% of the sulphur. The iron in the sulphides was oxidized to Fe3O4 (magnetite) at temperatures below 500°C and to Fe2O3 (haematite) at temperatures above 550°C. At 700°C the bed sintered and copper oxides formed. At temperatures below 450°C oxidation was incomplete: pyrrhotite remained and only 30% of the sulphur was removed. Smelting tests were conducted to assess matte fall and the deportment of copper and nickel to matte. It was evident that roasting resulted in lower matte falls (a drop of approximately 60%) compared with matte falls from unroasted concentrate. The iron and sulphur levels in the matte were reduced to below 3.5% and 22% respectively.This paper also briefly describes the mechanisms by which pyrrhotite, chalcopyrite, and pentlandite are oxidized during roasting. For chalcopyrite, the mechanism proceeds through an intermediate solid solution phase, which extends from Cu1.02Fe1.04S2 to Cu2.04Fe0.72S2 to a copper-rich solid solution of bornite (Cu4Fe1.4S4-Cu2S). The oxidation of pentlandite proceeds through a monosulphide solid solution (Ni0.39Fe0.53S-Ni0.74Fe0.15S) to a solid solution of heazlewoodite ([Ni,Fe]3}xS2). These mechanisms are explored in relation to chemical thermodynamics and microstructures."

Jan 1, 2015

"In mineral exploration and mining applications, it is sometimes necessary to reduce sampling error in order to improve representivity of individual sample assays. Historic efforts to reduce sampling error have relied on the belief that larger samples exhibit less sampling error. Justifications for this belief traditionally have coupled the binomial theorem with an ideal geological material consisting of ore and gangue particles of equal size and shape (an equant grain model) and empirical tests of geological materials, to illustrate an inverse relationship between sample size and sampling variance. To date, no proof exists of this sample size-sampling variance relationship in real geological materials exhibiting variations in grain size, shape, composition, and degree of liberation.Using first principles calculus and the formula for the mean, sample mass and sampling variance are proven to be inversely proportional in all geological materials. Distribution assumptions and physically ideal geological models are not used in this proof. Furthermore, algebraic manipulations of expressions describing the variances of equant grain models consistent with binomial, hypergeometric, and Poisson distributions reveal that these models also exhibit an inverse sample size-sampling variance relationship. Thus, the sampling behaviors of these models are numerically consistent with the sampling behaviors of real geological materials, and these models can be used to estimate sampling errors in real geological materials using simple sampling parameters."

Jan 1, 2007

By John F. Wiss

A series of controlled experiments was conducted at four surface coal mines to study the effects of certain blast parameters upon the ground and air vibration. Preliminary scale-model blasts were conducted at a quarry to provide basic data. It was found that the amplitudes of the ground and air vibration were controlled by the maximum explosive weight per delay. Either cube root or square root scaling could be used for the seismic amplitudes, and cube root scaling could be used for the overpressure amplitudes. Both amplitudes were not significantly affected by the total charge weight per blast, the attitude of the boreholes, or the charge length or diameter. The overpressure amplitudes were affected by the charge depth, the use of cover over surface detonating cord, and the use of adequate stemming. The length of the delay intervals and the spacing of holes were important in determining the potential for reinforcement of the amplitudes in certain directions from the blasts. In downwind directions from the blast, the attenuation of the overpressure with distance decreases. Surface terrain t did not significantly affect the overpressure amplitudes within the range investigated. The type of overburden affects the generation of both amplitudes and the propagation of the seismic amplitudes. Spectral analysis of the ground and air vibration is reported. A bibliography of pertinent literature is included as an appendix. A scaled distance of 300 ft/lb1/3 should produce a peak particle velocity of less than 1 ips and an overpressure of less than 128 dB linear peak. For square root scaling, a scaled distance of 75 ft/lbl/2 should limit the ground vibration to less than 1 ips.

Jan 1, 1978

By Brian R. Zuckerman

The Capitol Area East End Complex is currently being constructed under contract with the State of California Department of General Services on two sites adjacent to the grounds of the California State Capitol Building in downtown Sacramento. The complex will consolidate the headquarters of the Departments of Health Services and Education, which currently occupy several facilities located throughout Sacramento. When completed in 2003, the complex will be the largest civic office project in California history, with approximately 1.5 million square feet of office space and housing nearly 6,300 state workers. The total project is being constructed on five separate blocks in downtown Sacramento, Blocks 171 through 174 and 225. Separate design/build contracts were executed for the construction on Blocks 171 through 174 and the construction on Block 225. The scope of this paper is limited to construction on Blocks 171 through 174, which comprise a square, two blocks on a side, bounded by 15th, 17th, L, and N streets, located immediately to the east of Capitol Park and the State Capitol Building, as pictured in the image shown below.

Jan 1, 2002

In November 1999 Waihi Gold Mining Company commissioned its new crushing and conveying plant used to transport both ore and waste from the Martha Mine to its ore processing plant and also its tailings dam construction area. To date, a record monthly throughput of 854 000 tonnes throughput has been achieved. This paper outlines the measures taken subsequent to the commissioning of the system to achieve greater than design throughput and to mitigate the environmental and safety issues associated with operating the system in the middle of a town.

Jan 1, 2001

By Douglas Bartley, Brian Wingfield, Robert McClure

Recent studies and limited tests indicate favorable results utilizing high accuracy electronic detonator technology over conventional non-electric pyrotechnic systems. This study discusses the application of this technology using the Daveytronic programmable system in an on-going production basis. The study quantifies the performance as it relates to fragmentation, excavation, vibration and productivity in an eastern U.S. aggregate mining operation. In order to insure accurate data, tight field controls were adhered to during the drilling and blasting process as they related to blast design, bench preparation, pattern layout, drilling and blasthole loading. Following the blast the excavation and crushing procedures were studied to quantify any down stream advantages due to improvements in fragmentation. This study will help provide the industry with information as to the advantages of high accuracy electronic blasting systems over conventional pyrotechnic systems and show the results of an operation utilizing electronic detonator technology through their production season.

Jan 1, 2000

Application of the Anaconda Simplified Work Index for Multiple Test Sizes Vale uses Bond Work Index measurements extensively in a number of applications. The Bond Work Index is usually a good parameter for checking scale up procedures when sizing ball mills, as well as the basis for variability analysis whenever drill core data is available. It is typical to measure between 100 and 150 Bond Work Indexes, depending on the deposit characteristics. The Bond procedure is relatively complex and time costly. It also requires relatively large amounts of sample, which are very expensive to be obtained. The benefits of the Anaconda simplified procedure are: considerably smaller sample requirements and laboratory time. This makes it very much attractive at Vale's development centre, including geometallurgical mapping, operation efficiency control, mine to mill, etc. The Anaconda simplified procedure was implemented and evaluated at Vale's Development Centre using a number of ores and several samples of each ore totalling more than 190 measurements. The Anaconda simplified method was calibrated for several test sieves and a correlation for any test size was determined for Vale's test mill. The calibration was also extended for two sample top sizes. The relative error of the simplified procedure was found to be in the range of nine per cent which is within the expected error Bond standard procedure. The implementation of the Anaconda method at Vale's development center has been used with great success over the past years in several green field, brown field projects and operating plants.

Sep 13, 2010

By Vaughan R. Voller

"The wide range of length and time scales found in solidification processes are outlined and discussed. Methods for Direct Microstructure Simulation (DMS) are introduced. Key features in sharp interface and phase field models are presented. Concepts in micro-macro solidification modeling are covered. Basic details of microstructure and segregation models are provided. A description of a recent segregation micro-macro model is presented in detail.IntroductionA solidification process involves the containment of a liquid region, which, due to cooling, transforms over time to form a fully solid product. The development of the solid microstructure and the segregation of solute components during this transformation are controlled by phenomena that occur across a wide range of length and time scales. A ""successful"" model of a given solidification process needs to account for these phenomena. Standard models of solidification employ a discrete grid of node points and associated volume elements in the special domain, with a discrete time step to track the transient changes of nodal values, describing the composition and microstructure. Through the use of such models significant progress has been made towards a complete understanding of solidification process and phenomena (see the conference proceedings in Refs [1-9]). As solidification models become more sophisticated, however, they all run into the problem of resolving the full range of disparate space and time scales.Two approaches can deal with this problem1. Direct Microstructure Simulation (DMS) where the grid size and time step are chosen to scale with the smallest length and time scales of the given problem.2. Micro-macro modeling where the grid size and time step scale with the macroscopic process scale and phenomena at smaller scales are accounted for via sub-grid modeling and volume averaging.Currently full DMS of solidification is beyond the reach of available computer power and the application and development of micro-macro models is an important and critical research area."

Jan 1, 2001

By Sidney Katell

This Bureau of Mines study estimates capital investment, operating costs, and selling prices for three underground bituminous mines producing coal with annual production ranging from 1.03 to 3.09 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of November 12, 1973, under the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 indexes. Initial capital investment ranges from $12,938,200 for the 1.03-million-ton-per-year (MJ.Vl tpy) mine to $31,435,500 for the 3.09 MM tpy mine. Total capital investment ranges from $21,607,200 to $51,982,000 for the same mines. Corresponding selling prices for the coal range from $9.11 to $8.06 per ton, assuming a 12-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1974

By S. M. Spottiswoode, J. A. L. Napier, M. Kataka

The move away from the use of strike stabilising pillars at depth and the adoption of the more flexible system of mining towards final dip remnant pillars brings new opportunities for optimising mine design. In the initial planning stage, the size and spacing of the final pillars is designed using classical design criteria, through limiting modelled values of Energy Release Rate (ERR), Average Pillar Stress (APS) and Excess Shear Stress (ESS). In reality, mines often leave pillars that are larger than those originally designed. One of the reasons for leaving more ground is an unexpectedly high rate of seismicity. In this paper, we present developments in integration of modelling and seismicity that are aimed at developing design criteria that are more responsive to local conditions.

Jan 1, 2003

This paper characterizes the copper cycle, that is, the flows of copper entering and leaving the African economy over a one-year period (1994). The major flows over the entire life-cycle of copper are examined; these include production (mining, milling and refining), fabrication of semi-products and manufacturing of finished products, use, and the waste management system. The results reveal that substantial amounts of copper (of order705 Gg/yr) are mined in Africa; of that amount, about 70 per cent is exported following processing, 18 per cent is utilized by African fabricators, and 12 per cent is discarded. The flows of copper products from African fabricators and product imports from other continents exceed product discards by large amounts. This difference, about 0.25 kg Cu/capita/yr on average, is added to in-use stock, largely as wire, plumbing tube, and in electronics. Some 65 per cent of the copper in discard flows is contained in electrical and electronic products, where it is relatively easy to collect and process for reuse. About a third of the copper discard flows known is recycled. The actual percentage is almost certainly higher because of informal (and unrecorded) recycling. Much of the remaining discarded copper is diluted into the municipal waste stream, where recovery and recycling are probably not economically justified. Keywords: material flow analysis, resource management, material budgets, copper, stocks and flows, systems analysis, Africa, developing country

Jan 1, 2003