Search Documents

By Edmund S. Leaver

The selection of a process for treating a gold ore is governed primarily by the characteristics of the ore under consideration. The form in which the gold occurs, its mode of association with other minerals, and the size and surface condition of the gold particles are important factors which influence materially the choice of procedure for recovering gold. A knowledge of these characteristics may be obtained by microscopic and chemical methods combined with experimental testing. Cyanidation and amalgamation, either alone or in conjunction with flotation and gravity methods, are peculiarly adapted to the treatment of gold ores, especially those of relatively low grade. Gold alloys readily with mercury provided both present clean surfaces. The presence of oils and grease, antimony and arsenic minerals, or soluble sulphides have a harmful effect. Very small, flaky particles of gold frequently are lost in amalgamation because of noncontact with the mercury. Fine gold in pyrite, or gold having rusty or contaminated surfaces, is often lost for the same reason. Grinding or some form of abrasion sometimes removes surface films of iron oxide or substances of a similar nature, and alkalies or other chemicals are used to remove grease. Gold is readily soluble in cyanide solution, and this method of treatment is particularly effective in the recovery of gold from the tailings resulting from other types of concentration procedure. Cyanide solutions must contact the gold to insure recovery, and the porosity of the ore treated and the fineness of grinding required are important governing factors. The use of lime in cyanidation is necessary to protect the cyanide, to precipitate undesirable substances, and to settle slimes. Certain substances in ores are harmful in cyanidation; chief among them are those that combine with cyanide, forming cyanides, and carbon which precipitates gold from solution. Arsenic and antimony are also harmful if present in sufficient quantity. These and other difficulties encountered in cyaniding certain ores often are overcome by roasting prior to leaching. Zinc dust is used almost universally for precipitating precious metals from cyanide solutions. The refining and melting of the product may be accomplished by oxidizing the zinc before melting it in graphite pots with fluxes, although sulphuric acid is now used largely to remove the zinc before melting. Straight cyanidation practice is being replaced by flotation as a major process, followed by cyanide leaching of the tailings, but amalgamation is still needed as a primary process for the recovery of coarse gold before either flotation or cyanidation.

Jan 1, 1935

By T. W. Peglas, J. Doherty, R. A. Day

The South East Transit Project is a $520 million project in Brisbane, Australia which includes the construction of a 32 km Busway to access the south-eastern suburbs. Close to the centre of Brisbane, tunneling techniques have been used to minimise surface disruption. This paper describes some of the features of the longest driven tunnel on the project, the Vulture Street Tunnel. The Busway is a two lane expressway for buses which requires a 10.2 m finished width and a 12.6 m excavated span of driven tunnel. The Vulture Street Tunnel carries the Busway at minimal cover beneath the operating Vulture Street Railway Station, beneath a three storey office building and beneath the roadway to the Mater Hill Busway station. Halfway along the route, a Y-junction has been constructed to enable future connection with a light rail route. Key features in the design and construction of the Vulture Street Tunnel include: Use of canopy tubes to drive a 12 m wide tunnel beneath operating railway tracks with less than two metres of cover in highly weathered rock. Underpinning the office building in the route of the tunnel construction from within the building carpark. Construction of a 24 m span Y-junction with 7 metres cover of weathered and faulted rock. Use of predictive analysis as an adjunct to traditional back analysis to estimate the tunnel settlements from pressuremeter test results. This paper describes the design methodology with particular reference to settlement prediction, as well as construction innovations used to complete the tunnel. This paper will be of interest to all designers who have to create large spans in minimal cover in weak rock in urban areas and who have to predict the settlement

Jan 1, 2001

By L. Rademan

The kinetic leaching behaviour of a low-grade surface gold ore and a high-grade reef ore were evaluated to determine the achievable gold recovery from these ores and particularly mixtures of these ores. The reef ore material has a head grade of 13.40 g/t with a relative standard deviation of 3%, and the unprocessed surface ore material a head grade of 0.43 g/t with a relative standard deviation of 15.6%. It is concluded that the kinetic leaching behaviour of these free milling gold ores during cyanidation, is not influenced by mixing of reef and surface ore material. No statistically significant relationship exists between the achievable recovery by direct cyanidation and the head grade of the material fed. No ideal ratio of surface ore to reef ore could be established. It is recommended that these materials should be processed simultaneously to minimize the costs, security risks, and losses incurred in transportation.

Jan 1, 2012

Water rights and availability are extremely contentious issues in many mining regions around the world, in some instances leading to violent confrontation. This situation has the potential to only get worse because competition for 'scarce' water resources will increase with population growth. In this environment the dilemma facing the mining industry is how to generate confidence in developing a responsible, sustainable and transparent water management strategy that is recognised as such by all stakeholders. Whilst the water needs of the mining industry are minor compared to those of agriculture, an operating mine requires a relatively large quantity of water on a daily basis to carry out operations. Another contentious aspects of new mine development is the debate between all stakeholders on the amount and quality of water that a mine is able to discharge into the environment should this be required. There are a multitude of water resources available to the mining industry for operational needs however much of this water is saline and over the last two decades there has been a continual decline in water quality (ie salinity has increased). In today's world there are enormous internal and external pressures to reduce water consumption at a mine and/or alternatively use water not considered a resource by the local community (ie sewage, saline or salt water, desalinated water). Strategies to meet these objectives can be achieved by implementing good water management practices, by recycling process water, reducing water losses by evaporation and seepage (ie by increasing and improving dewatering practices) and employing new technologies such as dry stacking and dry processing. Recycled water, acid mine drainage water and water collected in the mining area have the potential to impact mineral processing performance, unless they are treated, because of the build up of mineral salts and decomposed chemical products in these types of waters. Besides this the regulatory requirements of any water discharged from a mine site (quantity and quality) have also become more stringent. For these reasons there is now some form of water treatment practiced at most mining operations around the world. This paper provides an overview of water stewardship undertaken in the mining industry over the last two decades and provides examples of water treatment practices that have recently been installed at mining operations that may be of interest to the reader.

Sep 13, 2010

By W. A. Scheuch

ORDINARILY secondary copper, unless electrolytically refined, is reclaimed directly as foundry ingots used in the manufacture of copper-rich alloy castings. This use does not require the elimination of the impurities to the degree required if the recovered metal is to be used for electrical purposes where a high electrical conductivity is of prime importance. However, as a part of the general policy of reusing its own scrap and by-products wherever possible, the Western Electric Co. at its Hawthorne Works is recovering its secondary copper as wire bars which are delivered to its own rod and wire mill and there processed into wire of high electrical conductivity. This departure from the usual recovery scheme has been accomplished through the careful classification and sorting of the material entering the furnace charges and the careful control of the subsequent melting and refining in a reverberatory furnace. Tests conducted over a period of approximately four years have shown that the quality of wire bars produced from selected secondary copper is equal to that of wire bars produced by the electrolytic refineries. The interest which has been exhibited in the process by those who have seen it has prompted the following general description. It is the authors' opinion that the recovery of secondary copper will become more and more an important factor in the copper production industry. The description is largely of the refining furnace and its operation, but it must be remembered that careful classification and sorting of the scrap materials to eliminate impurities are just as important as the furnace operation toward obtaining a satisfactory final product. Classification and sorting do not lend themselves easily to description; they must just be done. It should also be recognized at the outset that constant intelligent supervision is requisite to the success of the process because there are so many ways in which impurities can find their way into the final product.

Jan 1, 1929

By P M. Hancock

The West Coast contains one of the world's giant placer gold deposits with production since the 1860s totalling some six million ounces (present day value NZ$ 3.6 billion). The deposits have been worked variously by hand, ground sluicing, hydraulicking and/or elevating, blocking out, deep leading and bucketline dredging. Since the sharp gold price rise of 1979 - 1980 gold production has increased steadily (in spite of the closure of the Kaniere dredge) to some 30 000 ounces (933 kg) in 1984. Production is primarily from some 100 medium scale mining, operations treating 50 - 200 000 m3 of auriferous late Pleistocene fluvial gravels year. In spite of their economic value the deposits remain only poorly investigated and many fundamental questions relating to the origin and formation of the deposits remain unanswered. This paper attempts to describe the geology of the deposits and outline a genetic model for their formation, and then discusses some of the economic aspects and current limitations and opportunities of the growing alluvial gold mining industry of the region.

Jan 1, 1985

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal properties and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Where gas plays a dominant role, the term outburst is often used; where stress concentration is primary, terms such as burst, bump or bounce may be used. Hargraves [1983] presents an often cited review of outburst phenomena with emphasis on Australian conditions. Beamish and Crosdale [1998] indicate outbursts have occurred for over a hundred years and present tabulations of outburst numbers in major coal basins throughout the world. A central consideration is the rate of depressurization that occurs in the course of mining. Outbursts are not limited to coal seams and adjacent strata; they also occur in salt and potash mines [Molinda et al 1988]. Stress concentration and gas pressure act in consort, so the combined action is important to understanding the mechanics of bursts or outbursts and to the development of measures to reduce the associated hazard. Gas flow is a complicated phenomenon associated with diffusion of gas from micro-pores and the flow of gas along cleats. Laboratory measurements indicate both are dependent on stress and pressure [Harpalani and Ouyang 1998]. Moreover, gas permeability in porous media is often many times water permeability [Klinkenberg 1941]. However, there is also evidence that gas and water permeability are similar at elevated stress and follow Darcy?s law [Dabous et al]. Gas flow is also of importance to mine ventilation. Price et al [1973] in cooperation with personnel of the former U.S. Bureau of Mines developed finite difference models to estimate methane emission in mines in the Pocahontas No. 3 and Pittsburg seams using a premining pressure of 4.69 MPa (680 psi) and Darcy's law implying laminar flow. However, the effects of stress were not taken into account. In this regard, mine measurements of permeability are usually based on Darcy?s law [Peide 1990]. Early models of gas flow with stress effects were one-dimensional in space and time (x,t) and were developed with the goal of estimating the gas pressure profile from the face into the seam as time passed [Schlanger and Paterson 1987, Zou and Yu, 1999]. A zone of high permeability adjacent to the mining face was recognized in these early models. Later models based on the popular finite element method allowed two spatial dimensions (x,y) and variation in time (t) and for coal seam heterogeneity [Tang et al, 2002]. Zhu et al [2007] formulated a set of nonlinear equations involving a complicated stress-pressure-permeability relationship for application to coal seam gas flow and concluded the coupling was important but failure of coal should also be considered. Wold et al [2008] used a hybrid finite difference - finite element model interleaved with a reservoir simulation model to study outbursts based on extensive mine and laboratory measurements. An important feature of the modeling was the use of spatially variable material properties and Monte Carlo simulation to obtain quantitative estimates of outburst conditions and probabilities. Connell [2009] used the same reservoir simulation model as Wold but used the popular finite difference code FLAC3D for hydro-mechanical responses to evaluate two permeability relationships, one depending on porosity and the other on stress, and concluded that permeability changes with gas production were more complex than computed by either permeability model. Gadde [2010] in an integrated laboratory and field study of coal pillar strength explored the effect of spatial variability and concluded that design based on average strength was acceptable in some circumstances, although gas pressure was not an issue. Liu et al [2011] also applied a FLAC code to analyze two-dimensional gas flow and deformation of layered but homogeneous strata in a Chinese coal mine using a strain-softening model and concluded that damage and gas pressure were important to strata safety relative to the case without gas.

Feb 27, 2013

The Interior Department's Bureau of Mines is the Federal Government's primary research arm in the mineral and fossil-fuel fields. In accordance with its Organic Act of 1910, the Bureau's responsibilities have been reinforced since the passage of the Federal Metal and Nonmetallic Mine Safety Act of 1966, the Federal Coal Mine Health and Safety Act of 1969, and the Mining and Minerals Policy Act of 1970. The 1966 and 1969 acts deal specifically with the development of safe working conditions and a healthful working environment for those engaged in the mining industry, while the third sets the national policy as follows: " ... to foster and encourage private enterprise in (l) the development of economically sound and stable domestic mining, minerals, metal, and mineral reclamation industries; (2) the orderly and economic development of domestic mineral resources, reserves, and reclamation of metals and minerals to help assure satisfaction of industrial security, and environmental needs; (3) mining, mineral, and metallurgical research, including the use and recycling of scrap to promote the wise and efficient use of our natural and reclaimable mineral resources, and (4) the study and development of [ ]

Jan 1, 1972

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific- indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1971 at 5 million tons valued at $200 million, averaging $40.00 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, calcium carbonate, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface smoothness, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. The chart in Table 1, updated from the 3rd edition of Industrial Rocks and Minerals, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses.

Jan 1, 1975

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the un-fractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By A. Gronningsater

Introduction As is well known, the fight between the blast furnace and the reverberatory furnace in copper smelting during the second decade of the century ended with a victory for the latter, a result which must largely be attributed to the introduction of flotation methods. To my knowledge, no new blast furnace has been blown-in at any American copper smelter since the War. As the metallurgy of nickel, up to and including matte smelting, is generally considered a close parallel to that of copper, the introduction of reverberatory smelting in the big new smelter of the International Nickel Company at Copper Cliff, built in 1928-30, seemed a logical adherence to a well established trend. In view of these facts, considerable comment was made when Falconbridge Nickel Mines decided to retain the blast furnace in their smelter built about the same time, in 1929. A presentation of the reasons governing this choice should therefore be of interest. The basic principles underlying the Falconbridge practice, and the considerations guiding the successive steps in the operations, will be discussed in the following. To understand the problems involved, the character and mode of occurrence of Sudbury ore must be kept in mind. Large amounts of disseminated ore are generally present. Although the gangue usually runs only about 50 per cent Si02, the ore hoisted as a rule contains more silica than needed in the smelting operation; until recently this excess was removed entirely by hand picking (in later years supplemented by magnetic sorting methods), a difficult and not very satisfactory method, in which 'the border line between ore and waste is entirely arbitrary, and therefore too much depends on the judgment of the picker.

Jan 1, 1934

By Greg Barnes

Agenda ? The Mining Stock Life Cycle ? Current Environment ? Valuation ? Golds ? Valuation ? Base Metals ? Case Study ? Quebrada Blanca Hypogene Commodity Investment Cycle ? Macro-Economic Indicators ? LME Inventories ? watch the trend; rising inventories ? bad for prices, declining inventories good for prices ? OECD Leading Indicators ? PMIs ? Purchasing Manager Indices ? Industrial Production ? more important for metals consumption than GDP ? Housing Starts ? US, Europe ? Auto Sales ? All things China ? metal imports/exports; SHFE inventories; SRB stockpiling ? Seasonality ? it does play a role ? What is Chris Dutton (TDSI Quantitative Analyst) saying?

May 1, 2010

THOUGH the literature on the chamber process is considerable, it mostly refers to European conditions. Owing to the demand for acid for flotation and leaching at the mine, it may be necessary to work the process under other conditions. Consequently, some results obtained during the chlorination days at Mount Morgan, within the Tropic of Capricorn, may be useful for reference when working in a similar climate. Though the chambers must be protected against tropical storms, thorough ventilation should be provided, with plenty of space between the chambers, which are almost invariably crowded together. Not only does the space assist in the cooling of the chambers, but it is very desirable during repairs, when lead andtimber have to be hoisted up. The connecting flues between the chambers, which are fairly efficient mixers and condensers, should be round, supported from above, and with the least possible timber about them. Their position and arrangement deserve careful attention. Lattice work will be sufficient protection for the sides of the chambers, and the roof should be high and well ventilated. The Mount Morgan plant, crowded and not well situated, consisted of seven chambers (four over 50 ft. in length), one Glover tower 7 ft. 2 in sq. x 20 ft. high, one Gay Lussac 9 ft. sq. x 30 ft. higb, also one 5 ft. diam. x 25 ft. high. There was one pipe column 4: ft. sq. x 14 ft. 6 in. high. The chambers were run as one unit, and were much lower than those usually constructed in Europe-less than 15 ft. high. Provided that suitable timber can be obtained, 20 ft. is quite low enough. It should be quite satisfactory to use round poles for the studs, and so admit more air space between studs andlead.

Jan 1, 1920

By W. F. Visser

The growing availability of information and data analysis capabilities of recent years provides new opportunities for improving the performance of mining operations. By using real-time measurements and artificial intelligence, it is possible to respond faster to changing conditions, while accurate and timely information permits rapid evaluation of changes and fast business improvement decisions. This article presents a blueprint for alignment of systems, organizational design, and management practices to leverage these developments in performance-driven operations management in mining and mineral processing. The first component of the blueprint is a performance framework with a system of key performance indicators for production control that can be used across organizational levels. This system places improvement at the core of management activities, giving greater importance to improvement skills at lower organizational levels, so companies can leverage available information for improving operational control. Secondly, the blueprint defines an organizational structure that strengthens performance improvement with technological and change management capabilities. Finally, the blueprint proposes alignment of management practices, covering the optimization of short-interval controls, the application of an improvement project portfolio management system that determines the ownership of improvement projects, and the coordination of controls across the organization. This combination of systems, organizational design, and management alignment supports rapid decision-making at the right organizational level. Introduction of the presented blueprint for operations management enables mines to leverage the developments in information and analysis capabilities to improve the performance of operations.

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By R. G. Gürtunca, J. A. Breslin

This paper briefly describes the progress in mine safety in the United States, with emphasis on recent events that have followed since the explosion at the Sago Mine in January 2006. Legislation following the mine accidents last year and areas of work carried out by the National Institute for Occupational Safety and Health (NIOSH) related to the accidents are discussed. American coal production in 2006 was 1,150 million short tons. Most of this coal is consumed domestically, with annual exports of coal about 50 million tons. One third of annual production is produced at surface mines and the rest from underground. This coal is produced by about 82,000 miners working at 1,400 coal mines. Major improvements in coal mine safety have been made in the US since the Federal Mine Safety and Health Act of 1977. The fatal injury rate in underground coal mines between 1977 and 2004 was reduced by 47.8% to 0.036. The annual number of fatalities dropped from 112 to 14 during that period. Likewise, the non-fatal days-lost injury rate was reduced by 42.6% from 10.87 to 6.24. The improvements in mine safety during this period can be seen in the graph of underground coal mine explosion fatalities and injuries from 1980 to present, which is shown in Figure 1. Between 1984 and 1993 (9 year period) there were 5 explosions and one major mine fire, for a total of 55 fatalities. Over the seven year period from 1993 to 1999 there were no fatalities from coal mine fires and explosions. However, in the six years since 2000 there have been 5 explosions and one fire, which have caused 37 fatalities. [ ]

By R. Chen

Most tunnels built in Sydney encounter similar ground situations; they penetrate either the Hawkesbury Sandstone or the shales that lie beneath the city. Tunnels in these materials are generally sup-ported by rock bolts in combination with a shotcrete lining. A method of analysis is presented to improve our understanding of the long term behaviour of fiber reinforced shotcrete (FRS) materials and the tunnel support systems. A finite element method SAFEA (Semi-analytical FE Analysis) is developed to model the combined creep behaviour of a shotcrete lining and the Hawkesbury Sandstone. To model the time-dependent creep behaviour, the bulk modulus and shear modulus of the materials are represented by logarithmic functions in time. A Laplace transform is then applied to these functions of time and the solution of the problem found from a finite element analysis. Tablot?s method is then used to invert the transformed values and find the solution in real time. The time dependent creep deflection of the numerical tunnel models reflects the interaction of the shotcrete lining and rock which have different creep parameters.

Jan 1, 2008

By R. G. Cawthorn

The vertical distribution of platinum-group elements (PGE) in the Merensky and UG2 chromitite Reefs is highly variable, but does follow certain general patterns that allow the testing of geological models. In the Merensky reef, historically popular geological representations and interpretations have suggested that the mineralization occurs in a pegmatitic pyroxenite bounded by two chromitite layers. However, there are now enough published exceptions to this relationship to expose its fallacy. The vertical distribution of the PGE depends largely upon the separation between these two chromitite layers or the absence of one chromitite layer. Where separation is small or only one chromitite layer is present, there is considerable PGE mineralization in the footwall below the pyroxenite and lower chromitite layer. With increasing separation between the two chromitites, the mineral¬ization occurs progressively higher in the succession, and tends to track the upper chromitite layer. The view presented here is that the entire Merensky package is comprised of three events of magma emplacement, in which each has produced variable reaction with, and erosion of, the footwall, causing recrystallization of pyroxenite into pegmatitic pyroxenite. The magma then produced a chromitite layer followed by pyroxenite. Each chromitite layer is associated with some mineralization, which was extensively complemented by the subsequent formation of a sulphide liquid carrying PGE that trickled down through about 1 m of permeable crystal pile. The sulphide liquid formed after, not coincident with, the pyroxenite layers. The distribution of PGE in the UG2 chromitite shows up to three upward depletion sequences of PGE, also suggesting three events. The PGE are associated only with the chromite. The contribution from a sulphide liquid is considered to have been minimal for two reasons. Cu and Ni are extremely low in the UG2 which would not be expected if sulphides had been present. Also, by analogy with the Merensky, downward trickling of sulphides would have caused some PGE to be present in the footwall. There are some PGE in the footwall, but only where remnants of chromitite occur, and the hanging wall is lacking in PGE. In the northeastern Bushveld the UG2 chromitite is thinner than elsewhere, and there is a UG3 chromitite layer, not present elsewhere, that has a high Pt/Pd ratio. It is surmized that in the rest of the Bushveld the UG3 only appears to be absent because it has merged with the UG2 to produce the high Pt concentration at the top of the composite UG2. The non-accumulation of the package of pyroxenite-norite-anorthosite between the UG2 and UG3 in the northeastern Bushveld, which is not seen elsewhere, creates an interesting challenge to the formation of silicate layering in the complex. The mineralization in the Platreef is not addressed here. Keywords Bushveld complex, Merensky Reef, UG2 chromitite, geological evolution.

Jan 1, 2011