Search Documents

By Hamed Layssi, Farid Moradi, Thomas Tingson

This paper describes the feasibility and pilot study of of using existing non-destructive testing solutions for evaluating structural integrity and mechanical performance of mass concrete foundations. This paper includes two pilot studies using well-known NDT methods (i.e., Crosshole Sonic Logging and seismic tomography) for new applications (i.e., NDT inspection of mass concrete foundations). In the first case, we will examine an existing mass concrete foundation block with internal cracking, which has negatively impacted the strength and stiffness of the foundation block. A combination of pulse velocity and 2D tomography was used to evaluate the structural integrity in the foundation block. In the second case, the quality and integrity of newly built mass foundations were evaluated using Crosshole Sonic Logging (CSL). The methods are combined to locate potential sub-surface defects such as large voids and discontinuities. This paper aims to study the effectiveness of the NDT methods of Deep Foundations to assess the quality and structural integrity of new and existing mass foundations and explore the opportunity to extend the capabilities of these tests beyond their conventional use.

Sep 8, 2021

By Jewels Stover, Charles A. Luxford

Oklahoma City is undergoing a replacement program for an existing 66in (1.675m) water pipeline that conveys raw water from Atoka Reservoir to the City. This pipeline currently crosses the Canadian River on elevated piers and is subject to flood hazards. To replace the existing pipeline and mitigate flood damage concerns, two parallel microtunnels will be constructed below the river channel. Access is from construction shafts located near the midpoint of the tunnels; opposing drives are launched from each shaft. This geometry dictated shafts of significant depth – exceeding 120 ft. (37m). To accommodate the casing pipe segments and microtunneling machines, a minimum shaft diameter of approximately 34 ft. (10.4m) was required. Due to the difficult geologic setting, a reinforced secant pile compression ring is specified by contract in the top 70 ft. (21.3m) of these construction shafts to provide a very low permeability support system.

Sep 8, 2021

By Paul R. Lear

Sustainability continues to be an important aspect of remediation and infrastructure projects. Deep soil mixing (DSM), a common construction and remedial technology, can easily incorporate the following sustainability best management practices (BMPs), including Minimizing Total Energy Use and Maximizing Use of Renewable Energy; Minimizing Air Pollutants and Greenhouse Gas (GHG) Emissions and Maximizing Use of Machinery Equipped with Advanced Emission; Minimizing Water Use and Impacts to Water Resources; Beneficial Reuse of Materials/Reduction of Materials and Waste Reduction; Use of Local Labor and Supplies. This paper focuses on the sustainability of DSM treatment and provide carbon footprint calculations at least one completed DSM project which used these sustainability BMPs to demonstrate the environmental impact of the sustainability.

Sep 8, 2021

By Eric P. Bregman, Justin Zarrella, Ryan M. Coulson, Connor Johnson

Within a prominent Boston, MA suburb are a pair of historic stone and mortar structures built in the late 1800’s. Both the Main House and Carriage House have been maintained and occupied throughout their rich history, but renovations were needed to address structural concerns and building code compliance issues. The focus of this paper is to detail an innovative underpinning design that addressed ongoing settlement issues at the Carriage House. GZA GeoEnvironmental, Inc. (GZA) partnered with Phoenix Foundation Company, Inc. (Phoenix) to design foundation wall support systems for Consigli Construction Company (Consigli) that would effectively underpin the historic field stone foundations. Originally, conventional concrete pit underpinning and jet grouting were contemplated as methods for support. However, due to the age and condition of the existing foundations, worker safety concerns, and the risk of additional structural damage, GZA/Phoenix elected to pursue a less traditional approach. The alternate design consisted of micropiles used for combined temporary and permanent foundation support. The load transfer system included steel headers with needle beams cored through the field stone foundation walls and reinforced concrete grade beams/pile caps. To validate design performance and ensure worker safety, GZA installed a fully automated survey monitoring system to record lateral and vertical building deformations. This included real-time email alert notifications to inform the Project Team of any threshold exceedances. From the start of micropile drilling through full load transfer to the temporary support and permanent foundation systems, the underpinning performed as designed resulting in less than 3/16-inch of vertical and horizontal deformations observed. This magnitude of movement is less than half of what is generally accepted deformation tolerances for masonry structures and considered exceptional performance. The focus of this paper is to provide additional details on the unique design, sequencing, installation, and performance of the underpinning systems.

Sep 8, 2021

By Seth Robertson, Daniel Belardo, Travis Coleman

Thermal Integrity Profiling (TIP) is a non-destructive method used to evaluate drilled deep foundation integrity. This integrity testing method is specified more frequently, and is becoming an industry standard in the transportation and private construction sectors. This testing method utilizes heat generated during the concrete/grout curing process to assess deep foundation integrity over the evaluated length. With compilation of the measured temperature versus time and installation records, a model of the Effective Average Radius versus measurement depth is generated. The generated effective shaft model is highly dependent on specific construction details, subjective modeling parameters, and proper interpretation of concrete/soil heat dissipation characteristics. Key components of the TIP analysis include both qualitative and quantitative assessments. Qualitatively, variations or sharp reductions in temperature profiles may indicate potential anomalous regions. Quantitatively, a correlation is established between measured temperatures and estimated Effective Radii for subsequent integrity evaluation. Best practices in processing the TIP measurements are presented, including selecting the optimal time for analysis, normalizing the thermal profile, and proper interpretation of potential anomalous regions. Recommendations for implementing mitigation efforts and interpretation of the TIP results are presented.

Sep 8, 2021

By John C. Tosh, Peter M. Kandaris, Sheldon John

Geologic, geotechnical and hydrologic studies were performed for the design of 115 deep, large diameter drilled shaft reinforced concrete foundations (6 to 12 feet) to support tall steel monopoles for a new 13-mile long 230/69kV transmission line in southwestern Arizona. The subsurface conditions along the alignment posed a wide range of challenges for performing investigation and design studies. These conditions include saturated, loose granular flood plain deposits with generally low lateral capacity, potential ground loss up to 23 feet due to occasional river flow (scour and embankment loss), liquefaction impacts from nearby active fault seismicity that can generate magnitude 6.5-7.0 earthquakes, and unsaturated alluvial and eolian sand-dominated soils to full depth with low lateral capacity. All conditions will require significantly deeper than normal foundation embedment (depth ranging from 22 to 77 feet) and will present construction difficulty due to ground instability from groundwater and dry soil sloughing. A phased investigation was performed to accurately characterize the conditions for design and construction, and included performing a review of existing data, detailed field geologic reconnaissance, a limited number of standard exploratory borings (limited access), seismic cone penetrometer soundings (SCPT) in saturated soils to better understand liquefaction and strength loss potential, and hydrologic analyses to estimate scour/ground loss potential. This paper describes the site conditions, presents details on the investigation team’s approach, documents findings in relation to deep foundation analysis and design, and discusses recommendations for foundation construction to help in reducing risk.

Sep 8, 2021

By Mark D. Fuhriman, Parham Khoshkbari, Robert Fosse

Drilled displacement piles are becoming an increasingly common deep foundation choice for their relatively simple installation methods, applicability to a wide range of subsurface conditions, and versatility. The installation method includes drilling and displacement of the soil followed by delivery of fluid cement grout under pressure, and placement of steel reinforcing to complete the pile. Because the installation method uses blind processes that do not permit direct observation of the pile, it is desirable to employ redundant testing tools to complement good construction techniques and inspection practices to ensure integrity of the piles. This paper examines the use of a range of integrity testing tools used for pile installations at a major office campus development. Because the integrity of a drilled displacement pile and its performance depend to a large extent on the skill and experience of the installation crew, the paper explores how use of multiple practical tools, including automated monitoring tools on the pile installation equipment, thermal integrity profiling, and high-strain dynamic testing, ensure structural integrity of the completed piles and how redundant integrity testing methods complement good construction and inspection practices add confidence in the quality of the foundation system.

Sep 8, 2021

By Gerald Verbeek, Erick Baziw

Cone penetration testing (CPT) is a popular and cost effective tool for geotechnical site characterization. CPT consists of pushing at a constant rate an electronic penetrometer into penetrable soils and recording cone bearing (qm), sleeve friction (fs) and dynamic pore pressure (u) with depth. The measured qm, fs and u values are utilized to estimate soil type and associated properties based predominantly on empirical correlations. The cone bearing measurements are highly susceptible to additive measurement noise for sandy, silty and gravelly soils. This measurement noise results in high peaks due to interbedded gravels and stones and low peaks due to softer materials or local pore pressure build-up. To date there has been little progress in filtering this additive noise aside from ad hoc techniques, which include discarding qm measurements and smoothing/averaging qm measurements. This paper outlines a qm filtering technique which attempts to put structure into the estimation problem. In this case, the dynamics of the cone bearing measurements are modelled within a state-space mathematical formulation and a Kalman filter (KF) is then utilized to obtain optimal estimates of qm. The mathematical details of the qm KF algorithm are outlined in this paper along with the results from a challenging test bed simulation.

Sep 8, 2021

By Murad Y. Abu-Farsakh, Md Habibur Rahman

The properties of all natural soil deposits are highly variable, and they are rarely homogeneous. Cone penetration tests (CPT) were used to assess the site variability, which was then incorporated into the Load and Resistance Factor Design (LRFD) of pile foundations. Data from six project sites with multiple CPT tests conducted at various locations were collected for this research. The semi-variogram was used to assess the spatial variability of CPT data (corrected tip resistance, qt) for each location. For each location, the coefficient of variation due to spatial variability (COVR,spatial) was calculated. From COVR,spatial and COVR,method, the total coefficient of variation (COVR,total) for each site was calculated, which was then used to calibrate the resistance factors (ϕspatial, ϕtotal) for use in LRFD pile foundation design. The findings of this study demonstrated the importance of using site variability in LRFD pile design. For sites with lower site variability than the design method (i.e., COVR, spatial < COVR, method), the value of the COVR, total will be decreased, and hence the resistance factors (ϕspatial or ϕtotal) will be increased (credit), and vice versa.

Sep 8, 2021

By Michael G. Batten, Brian D. Keaney

]The Virginia Department of Transportation (VDOT) and the harbors on the James River routinely use precast concrete piles founded in the Yorktown formation to support bridges and other coastal structures. However, axial pile resistances for large diameter piles in this area have been historically overestimated on past projects. This may be due to a common assumption that very large unit end bearing resistance will be developed for a large diameter displacement pile that is driven a significant depth. This assumption is integrated in the Nordlund (1963; 1979) method which is commonly used to estimate axial pile resistance for bridge foundations. A static and dynamic pile load testing program was implemented as part of the Hampton Roads Bridge and Tunnel Expansion project in Norfolk, VA in the James River. A primary objective of this program was to calibrate an axial resistance calculation method against the measured load test results. A method developed by Eslami and Fellenius (1997) that uses CPTu data directly was effective at calibrating to the measured load test results, and allowed for clearer interpretation of the unit resistance values than indirect, semi-empirical methods that require interpretation of soil friction angle and undrained shear strength.

Sep 8, 2021

By Dominik Gächter, Wojciech Szczepiñski

In early 2020, the construction phase began for the new complex of buildings for Radium Hospital in Oslo – the leading facility for cancer treatment in Norway. Settlements in the surrounding area, caused by pore pressure changes, allowed for the introduction of an alternative solution for the construction of the excavation pit. The presence of solid bedrock and sensitive clay – the same material that causes major landslides in the Scandinavia – in the excavation pit, lead to a combination of techniques, which were never applied in Norway before. For the stabilization of the clay Dry Deep Soil Mixing was applied to allow safe execution of the geotechnical works. Interlocking Bored Piles with footbolts and Jet Grouting columns, in combination with anchors, provided the retaining structure for the excavation pit. Rock injections were performed to avoid any ground water ingress into the pit. Underpinning of fully operational, adjacent buildings was carried out with jet grouting columns. These works were performed from the basement of the hospital and the ‘ACI – Acoustic Column Inspector’ was used to ensure proper installation of 2 m diameter columns to a maximum depth of 25 m. The buildings were later founded on Steel Core Piles, the most common pile type in Scandinavia.

Sep 8, 2021

By Challa Venkata Rami Reddy, Anindya Roy, G. R. Konni

This paper presents the results of pile lateral capacities obtained from both conventional design and fullscale pile lateral load tests. Conventional design using P-Y curve analysis is very commonly being used by designers; designers use well accepted software programs like Lpile and Allpile for analysis. However, these programs do not cover the soil models to simulate engineering behavior of marine carbonate sands; which generally have different engineering behavior than silica/quarts sands. In this study, the existing soil models for common sands have been used to assess pile lateral capacities and these results are compared with the results from full-scale instrumented pile lateral load tests performed in compacted marine carbonate sand fills of artificial island constructed for oil and gas facilities in Abu Dhabi. The objective of this study was to verify the applicability of the existing sand soil models for carbonate sands and also to verify the associated conservatism in the pile lateral capacities. This study shows that the actual pile lateral response is much stiffer than what was anticipated through the LPile analysis. Therefore, further research focus may be required to capture the engineering behavior of the marine carbonate sands to develop specific P-Y curves.

Sep 8, 2021

By Ralphie Adams, Tiana Rasmussen, Ashley E. Shirer

Transmission line foundation designers must rely on limited subsurface information, from easily accessible locations, resulting in subsurface uncertainty, increased design risk and increased construction costs. This paper presents a different approach for foundation analysis conducted in mountainous and alluvial floodplains located northwest of Phoenix, AZ. The region is dominated by fault-bounded, northeast dipping mountain ranges, where rock types and drillability can vary from granite to intact basalt. The valleys between are comprised of “basin-fill” deposits ranging from conglomerates and cemented soils to lose alluvium. Recently deposited alluvial fills can vary in depth significantly from location to location due to erosion and deposition from active and historic hydraulic features. To limit the subsurface uncertainty for foundation design, a phased approach using geophysical surveys along with detailed geologic reconnaissance was employed. Both compression wave and shear wave velocities were measured in order to identify the depth and properties of loose erodible materials from more scourresistant cemented, conglomerate, and rock deposits. These analyses were used in combination with limited subsurface drilling and sampling to evaluate direct embedment steel pole foundations for over fifty structures. Post analysis results from limited construction drilling reports were used to assess this approach.

Sep 8, 2021

By Mark Zablocki, Dakarai McCoy

Ground vibrations are an unavoidable effect of driving piles and may pose a risk to nearby infrastructure and the comfort of adjacent occupants. Driven-pile-induced ground vibrations are known to vary widely based on ground conditions, pile material, and installation means and methods. A monitoring sensor to record ground vibrations during pile driving is necessary for understanding potential impacts to sensitive infrastructure and should be considered when implementing a monitoring program anticipating ground vibrations. The implementation of a vibration monitoring program historically relies on experiential-based decision-making, which may result in the costly vibration monitoring of low-risk infrastructure. Prior understanding of anticipated ground vibrations is necessary to create an appropriate monitoring program. A framework is proposed for organizing data from past monitoring programs and quantifying the anticipated risk of driven-pile-induced vibrations. An example of risk quantification from data imported to ]a cloud database is presented by comparing driven steel H-pile and prestressed precast concrete vibration monitoring measured and collected by Haley & Aldrich between 2010 and 2020. The methods presented within the example can be applied to quantify a first order approximation of risk for ground vibrations at proposed driven pile sites based on the measured performance of previous sites with similar ground characteristics and pile installation methods. The presented novel data managements tools allow for a quick aggregation of vibration data with similar site conditions.

Sep 8, 2021

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

With the increase in population over the last decade, and anticipated population growth over the coming years, Norway is making significant investments in the Country’s infrastructure. Part of this investment in development starts with the Intercity development project in South-East Norway, which is the largest transport project in Norway. The Intercity Development project consists of 270 km (167 mi.) of new doubletrack rail, capable of train speeds reaching 250 km/h (155 mph). The new stations are centrally located in the major cities, in South-East Norway, to provide the benefit to as many citizens as possible. The goal of the project is to reduce the increase in traffic, which is coupled with an increase in population, and reduce the travel times between the cities. The Intercity Development Project has an anticipated completion date of 2034. The Sandbukta-Moss-Såstad (SMS) project, part of the Intercity development, includes 10 km (6.2 mi) of new double-track railway and is situated on the Østfold Line, near the city of Moss, Norway shown in Fig. 1. The 10 km SMS-section covers three open stretches and two tunnels, including 630 m (2,066 ft) substructure for double-track railways on the open line at Sandbukta. The Moss tunnel is a 1720 m (5,643 ft) long tunnel from Sandbukta to Moss center, including a 420 m (1,378 ft) long concrete culvert. The new Moss station includes an 800 m (2,625 ft) long station area. The Carlberg tunnel is a 2350 m (7,710 ft) long tunnel from Kleberget to Carlberg, including a 200 m (656 ft) long concrete culvert.

Sep 8, 2021

By Martin Walker, Joseph Ang, Jongwon Lee, Alvin Bayudanto, Lilian Lorincz, Morteza Khorshidi, Wenyong Rong

This paper presents a case history of liquefaction susceptibility evaluation study for a major infrastructure project in the San José area. The subsurface material of the study area consists of Holocene alluvial deposits composed of interbedded and crosscut clays and silts, sands and gravels. The simplified approach for liquefaction triggering evaluation was carried out using both CPT data and SPT data representing site’s seismic capacity and the peak ground acceleration associated with a return period of 975 years at ground surface representing seismic demands. Site-specific cyclic stress ratio (CSR) profiles as seismic demand are also estimated from one-dimensional site response analysis. The simplified approach uses empirical depth stress reduction factors (rd) based on generic shear wave velocity profiles to account for the non-rigid response of the soil profile in estimating CSR. The CSR profiles of the simplified procedure were examined by completing site response analyses using site-specific soil profiles to represent site-specific seismic demands in the liquefaction triggering evaluation. The paper concludes with a comparison and discussion of the liquefaction evaluation examining results from CPT versus SPT data, and the comparison of CSR profiles from the simplified procedure versus site-specific response analysis.

Sep 8, 2021

By Racquel Nottingham, Marc Mastrantuono, Freddy Lopez

In the digital era that we live in, connectivity and mobility play a decisive role in our daily activities. In this context, insufficient telecommunication infrastructure gives origin to the so called “dead zones” (areas with poor or non-existing cell phone reception), which hinder economic development in small communities and in many rural areas, since they remain invisible to a larger marketplace due to the inadequate cellular coverage. Several countries are working to identify these dead zones and with this information, establish strategies together with mobile providers in order to improve the existing mobile networks by expanding the coverage areas. As a result of the analysis, it is expected that thousands of telecommunication towers for 4G and 5G networks will be erected in the coming years. Telecommunication towers are slender elements that require large shallow foundations to verify primarily the safety against overturning. However in remote areas, it can be advisable to consider alternatives to the conventional shallow foundations, in order to optimize the use of materials (concrete, reinforcement steel, etc.). The following article presents an overview of intervention projects, where telecommunication towers were founded on micropiles. The micropiled foundations allowed to reduce considerably the dimensions of the originally planned shallow foundations. Furthermore, the use of micropiles allows for additional optimization, in combination with pre-fabricated foundations (i.e., precast concrete elements, etc.). This paper will focus mainly on the design and the execution of the micropiled foundation.

Sep 8, 2021

By Abdulazeez Rotimi, Barry Sheppard, Abid Adekunte

Good engineering practice is a function of sound theoretical knowledge, first-hand experience on previous projects of similar scope and scale, good acquaintance with case histories of similar projects completed by others in similar environmental conditions, as well as satisfactory degree of exposure to state-of-the-art methodologies. The four factors itemised above are typically interdependent. They amalgamatively influence the judgement of the Engineer and they ultimately result in the delivery of safe and cost-effective solutions by Professional Engineers. This technical paper presents detailed information on the ground engineering aspects of a large-scale housing development project located on a sloping site that had been presumed to be unstable in West Sussex, England. The ground engineering design package for the scheme comprised of temporary working platform designs & stability assessment for piling rigs and other construction machinery, geostructural designs for approximately 1km total run of permanent bored pile retaining walls to support the split-level construction on the sloping site and geostructural designs for the permanent foundation piles to support the housing units. The paper details how the four factors outlined above were amalgamated by the project’s foundation specialist consultants & piling contractors to deliver safe and practical solutions for the development, with significant savings in materials, cost and project completion time.

Sep 8, 2021

By M. Kitazume, H. Imai

The deep mixing method was developed in Japan and put into practice in the middle of 1970s. Since then, the wet and dry type methods have been applied for various improvement purposes in Japan. One stork of mixing tool produces a column shape of stabilized soil in a ground. By the series of productions, arbitrary shape of improved ground can be constructed by overlapping each columns. It is specified to complete the overlapping within 24 hours in order to ensure the tight connection of the columns. However, it can not be completed within the specific time in some cases due to bad weather or machine trouble, which causes a cold joint in the improved ground. In this study, the influence of the cold joint to the behavior of the block type improved ground is examined by a series of centrifuging model tests and FEM analyses. It is found that the ground behavior is influenced by the position of the cold joint, where the cold joint at the sea side shows a little influence to the behavior but one at the port side causes large decrease in the stability of the improved ground.

Sep 8, 2021

By Arash Saeidi-Rashk-Olia, Dunja Peric

Energy piles are gaining increased popularity due to a growing demand for clean energy. To further advance the understanding of soil-structure interaction in energy piles, recently-derived analytical solutions have been implemented to investigate the impact of stratigraphy on the soil-structure interaction. This was accomplished by comparing the measured and predicted head displacements, axial strains and stresses in an energy pile embedded in the actual homogeneous and layered soil profiles, as well as into synthetic homogeneous soil profiles. The analytical solutions for homogeneous soil profile captured the smooth experimentally observed response versus depth very well. In the case of a layered soil profile, the corresponding analytical model was capable of capturing nuances in trends of axial stress and strain versus depth at the interface of different layers. The analytical predictions for the layered profile appear to be slightly less accurate than for the homogenous profile. The experimental data obtained from the layered profile appear to be a bit more scattered than those from the homogeneous profile. In the former case, the interplay of the individual soil layers with the pile occurs while maintaining the continuity of the pile stress and displacement at the interface of different layers. The response throughout each layer of the layered profile is quantitatively different than the corresponding homogeneous response. Nevertheless, qualitatively the response throughout each layer of the layered profile is similar to the response of the pile embedded in the corresponding homogeneous layer.

Sep 8, 2021