Search Documents

By Michaela Dina Stanescu, Emilia Visileanu, Eftalea Carpus

"The recovery and reintroduction into the economic circuit of the textile material resources must be considered as component parts of the strategies of harmonizing the relationships between the economic growth, consumption of natural resources and environmental protection of the existing socio-economic system.The waste recovery for ensuring a sustainable development is a major concern of all industrial researches. In the textile domain, the concern in this matter is becoming more evident. An important role in manufacturing textile products it has the notion of eco-design, which has grown considerably over the last twenty years with increasing awareness of environmental and social problems in the industry.Introduction“Humanity must learn from the global financial and economic crisis experience""- is the conclusion of the policy makers who should develop a strategy designed to reinvigorate the economy and make possible an"" intelligent, sustainable and favourable to inclusion” growth, by a better coordination of national and European policies.The new vision for social market economy is based on three priority areas: smart economic growth, the development of an economy based on knowledge and innovation; sustainable economic growth, the promotion of a competitive economy with low carbon emissions and an efficient use of resources, as well as an inclusive economic growth, the promotion of an economy with high degree labour employment, which would generate social cohesion. The recovery and reintroduction into the economic circuit of the textile material resources must be considered as component parts of the strategies of harmonizing the relationships between the economic growth, consumption of natural resources and environmental protection of the existing socio-economic system.The waste recovery for ensuring a sustainable development is a major concern of all industrial researches. In the textile domain, the concern in this matter is becoming more evident. It is obvious that at the origin of pollution there are the technological processes of textile processing with impact on air, water, soil, as well as the storage processes. In all phases of obtaining a product, a series of secondary products and textile wastes with impact on the environment occur. The product used becomes also a factor of environmental pollution, which in most cases fails to assimilate."

Jan 1, 2012

By R. H. Hanewald

INMETCO, a subsidiary of Inco Limited, is the only facility in North America that provides High Temperature Metals Recovery for nickel-, chromium-, and iron-bearing wastes. Since 1978, this process has prevented more than 775,000 tons of materials from becoming part of the nation's waste stream. The paper describes Inco's experience in metals recovery, traces the development and explains the operation of the High Temperature Metals Recovery Process, and examines the procedures and criteria used to determine whether spent catalysts meet process feed specifications. An overview of the current requirements for transporting spent catalysts is provided. The paper concludes with brief case histories of catalysts users employing High Temperature Recovery to manage spent catalyst.

Jan 1, 1995

By C. Dresen

This paper discussed the reaction kinetics of the reduction of industrial phosphate pellets for P4 production. In the reduction process of various phosphate ores, the following parameters were investigated: Diffusion of the phosphorus oxide and other gaseous products from the reaction mixture after having been reduced on the reductant (coke) surface. Influence of silica on reaction kinetics. Temperature influence. Influence of mineralogy and morphology (different ores). Particle size influence of silica and coke. Experiments were carried out in a vertical tube furnace with 2 ores, 2 types of silica and one type of coke. Selected experimental conditions simulated furnace conditions. The following conclusions could be made: Reaction rate increases with the addition of SiO2 into the pellet. The reaction rate increases above 1350°C (melting temperature of the slag). Mixing different ore types in the pellets leads to differences in reduction kinetics. Particle size of the coke particles influence reduction kinetics. The amount of slag formation is influenced by silica addition, coke size and temperature.

Jan 1, 2002

By A. J. Duncan, S. Viswanathan, Q. Han

"Measurements of liquid permeability in the mushy zones of Al-15.42% Cu and Al-8.68% Cu alloy samples have been performed isothermally just above the eutectic temperature, using eutectic liquid as the fluid. A modified method has been developed to determine the specific permeability, Ks, as a function of time during the test from the data collected on these alloys. Factors affecting permeability measurements are discussed. Permeabilties are observed to vary throughout the experiment. This is attributed to rnicrostructural coarsening and channeling that occurs in the sample during the experiment. The permeability is related to the rnicrostructure of the sample using the Kozeny-Carman equation. The correlation between the measured Ks, liquid fraction, gL and the specific solid surface area, Sv, improves markedly when compared to previous studies in which rnicrostructural coarsening was ignored.IntroductionThe permeability of interdendritic liquids flowing through dendritic structures ·is an important parameter needed to predict the level of porosity in castings. The permeability is a component of Darcy's Law, used to estimate the pressure drop due to the resistance to the flow of interdendritic fluid to feed shrinkage. Therefore, much research has focused on measuring the permeability of alloys in the mushy zone (1-10). The Kozeny-Carman equation for liquid permeability in the mushy zones of alloys may be written as"

Jan 1, 1999

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By Batric Pesic

Adsorption of gold on activated carbon from gold bromide solutions was examined as a function of pH, particle size, carbon amount, initial gold bromide concentration, bromine concentration, temperature, and various cations and anions. pH did not have any effect below pH=6. Above pH=6, pH had dramatically negative effect. The adsorption results satisfied a first reaction order model. The reaction rate constant was proportional to the inverse of carbon particle radius. It was also proportional to the amount of carbon, and independent of initial gold concentration. Temperature had a very little effect at pH=l. At pH=8, the activation energy was a function of the extent of a reaction, increasing with the extent of a reaction. Cu, Fe, Ca, Mg, and Na cations and sulfate, chloride and bromide anions did not have any effect on gold adsorption. Bromine had a very negative effect on gold uptake.

Jan 1, 1991

By G. Kugler, M. Tercelj

"The use of the up-to date light alloys and their development are in the sharp ascent especially in transportation industry. In the last years the use of the magnesium alloys for the various purposes was strongly increased. The aim of present research was to study the influence of solidification rate on hot workability and on obtained mechanical properties of AM60 magnesium alloy. The study was also focused on possibility to omit prior homogenisation process which would result in cost reduction. The solidification of gravity cast alloy has been investigated with various methods of the thermal analysis: in situ simple thermal analysis and simultaneous thermal analysis. In order to reveal optimal hot working conditions the deformation behaviour was studied in the temperature range 200-450°C and strain rates between 0.001-lOs-1. Mechanical properties have been studied with tensile and impact toughness testing.IntroductionIn recent years, the increased demand for magnesium alloys has been mainly driven by the need of automotive and transportation industry to reduce the weight, as this is the most important parameter to reduce the energy consumption. Beside their very low weight in comparison to other metals, the magnesium alloys are characterized by good machinability, corrosion resistance and good mechanical properties, and can thus compete with aluminium alloys and for some applications even with steels. Due their decreased workabilty they are typically used as cast alloys, but in recent years also the research of their wrought state has become more extensive [1-7]. Decreased hot workability of magnesium alloys originates from their hexagonal close-packed structure. One of the most popular magnesium alloys with great potential for many applications is AM60 (MgA16Mn), which is predominately used for casting. But its application could be increased if the mechanical properties, could be improved. This can be done by hot working. Namely it is well known that wrought microstructure is characterized by better mechanical properties in comparison to as-cast state. On the other hand due to its low hot workability the homogenization process is required prior hot deformation, which results in increased production costs. Thus the aim of the present research was to study the influence of solidification rate on hot workability of AM60 alloy in order to improve its mechanical properties and to check the possibility of producing near-net-shape casting products omitting homogenisation process by employing small additional deformations after casting. Within the framework of this research the solidification of gravity cast AM60 alloy has been investigated with various methods of the thermal analysis."

Jan 1, 2011

By M. Somerville

In 1989 CSIRO Minerals initiated investigations into continuous converting of copper matte into low sulphur blister in Sirosmelt type reactors. Following the successful piloting of this processing route, some effort was directed towards a single stage copper making process where copper metal is made in one step from concentrate. The aim of the project is to develop a continuous process, which offers considerable environmental and economic benefits over conventional copper making processes, which use Pierce-Smith converters. In the selection of the optimum flowsheet a number of slag treatment options have been considered and tested. These unit operations include: leaching and electrowinning, flotation-leaching-electrowinning and flotation with recycling of recovered copper through the smelting vessel. In this paper the suitability of these process options are evaluated using the available information and recently measured copper recoveries from our testwork at CSIRO. The operating and capital costs of the various options have been estimated using Aspen Plus simulation procedures. The most attractive flowsheet in terms of capital and operating costs is the treatment of slag using mineral processing techniques and the recycle of a copper slag concentrate to the smelting vessel. It has been found that the chemistry of the slag being treated has a large bearing on the recovery of copper in flotation and hence on the economics of the process.

Jan 1, 1999

By Guangwei Wang, Changle Zheng, Yifan Chai, Jian Guo, Weiwei Geng, Jianliang Zhang

In this paper, characteristic and kinetics of CO2 reaction with four different kinds of coke such as top-loading coke, dry quenching tamping coke, wet quenching tamping coke and semi-coke were investigated based on isothermal method. Electric resistance reduction furnace was used to heat the sample. Volume Model (VM) and Shrinking Core Model (SCM) were used to calculate the kinetic parameters and to contrast with the experimental results. The results showed that the Volumetric Model (VM) was much suitable for the reaction of top-loading coke, dry quenching tamping coke and wet quenching tamping coke, while Shrinking Core Model (SCM) was much suitable for semi-coke.

Jan 1, 2015

By Fumito Tanaka

In the Mitsubishi Continuous Copper Smelting & Converting Process, the heat for the dissolution of scraps is effectively supplied from the melts strongly stirred by top injection. Various kinds of shape of scraps not only powder but also lump, sheet, cube and so on can be treated without any emission of dust and fugitive gas, and no additional furnaces for scrap processing is necessary. Therefore, this process is much suitable for recycling. The authors have investigated the melting rate of ice sphere into a water bath equipped with top blowing lances as a basic study for the dissolution of scrap. Hydrodynamic experiments were carried out, and mathematical models were applied to the results. The results show that the melting rate of ice sphere strongly depends on the standing waves at the bath surface.

Jan 1, 2001

By Reza Rahimi, M. Nili Ahmadabadi

"Because of high cost and shortage of primary resources of Ni-base superalloys, revert alloys can be used as a part of charging materials for production of superalloys ingots. The current study is based on recycling of IN738LC, a Ni-base superalloy, using 30% and 50% reverted alloy and balanced amount of virgin raw materials. Therefore, it has been attempted to cast an alloy with references to standard chemical composition and mechanical properties. After charging and casting in vacuum melting furnaces, chemical composition verification and non-destructive tests (i.e. Penetration and Radiography Tests), quality of samples were evaluated at elevated temperature by stress-rupture test. Results acquired from chemical composition and mechanical test indicate that cast ingots using 30% and 50% reverted alloy is reliable and consistent with the quality control requirements.IntroductionIn recent years, there have been many fluctuations in cost and availability of raw materials which are extremely determining in Ni-base superalloys production. Accessibility to the high purity metals such as Cobalt, Molybdenum, Tantalum, Niobium and etc. have been problematical during the past decades. Therefore, shortages of critical raw materials beside the economical considerations motivated the alloy suppliers and investigators to study and find alternate sources such as reclamation and recycling of scraps [1].There are a lot of reasons for the necessity of recycling; perhaps the most justifiable one is that consumers themselves produce scraps. For example, the weight of a finished superalloy product could be less than one-third of the cast alloy weight and in the case of complicated machined parts; this portion may reach to one-tenth [2]. High values of constituents, reduction of energy consumption and environmental concerns have all strengthened the obligation of recycling in Ni-base superalloys.Because of the high degree of risk in usage of improper materials for production of turbine blades, a delicately controlled program for recycling is needed. Depending on the type of scraps, this program can define the recycling procedure, required instruments, allowable percentage of scrap for usage and finally confidence level of the process."

Jan 1, 2012

By Nico Steenekamp

At Lonrho Platinum in South Africa, ores from both the Merensky and UG2 reefs of the Bushveld Igneous complex are treated by flotation and smelting to produce a nickel-copper matte which serves as a collector for the platinum group metals (PGM' s). The nickel-copper matte was originally shipped to Norway for treatment and recovery of the contained base metals, with the return of the PGM rich concentrate to South Africa. The Lonrho Platinum Base Metal Refinery was commissioned in 1985. The original process employed a Shenitt Gordon design. The converter matte is treated in a refinery which utilises both atmospheric and pressure leaches for the dissolution of base metals to produce nickel sulphate crystals, copper cathode and a PGM concentrate. This paper refers to flowsheet and operating changes as well as improvements within the Base Metal Refinery.

Jan 1, 1999

By Do-Hyeong Kim, Tae-Jung Kim, Seung-Yeon Won, Jong-Jin Pak, Min-Kyu Paek

Liquid iron alloys containing V, Mo, and Ni can be produced by the carbothermic reduction of spent catalysts used in petrochemical industry. Thermodynamics of carbon in these alloy melts is important for refining these alloys. In the present study, the carbon solubility in Fe-V, Fe-Mo, Fe-Ni, Fe-V-Mo, Fe-V-Ni, Fe-Mo-Ni and Fe-V-Mo-Ni alloy melts of various compositions was measured at 1873 K. The temperature dependency of vanadium effect on carbon solubility in liquid iron was also measured in the temperature range from 1823K to 1923K. The additions of vanadium and molybdenum significantly increased the carbon solubility in liquid iron alloys while nickel decreased the solubility. The experimental results were thermodynamically analyzed using Lupis’ relation at constant activity to determine the first- and the second-order interaction parameters of vanadium, nickel and molybdenum on carbon at carbon saturated condition. Using thermodynamic parameters determined in the present study, the carbon solubility in Fe-V-Mo-Ni alloy melts of various composition were accurately predicted and verified experimentally at 1873 K.

Jan 1, 2014

By Chenhui Liu, Hong-ying Xia, Bingguo Liu, Wei Li, Jinhui Peng, Libo Zhang

"Dielectric property is an important limiting factor in the development of microwave processing of minerals and ores. In this study, we used an open-ended coaxial sensor method to measure the complex permittivity of an ilmenite concentrate (41%TiC>2) and microwave absorption properties from room temperature to 100°C. The results show that the dielectric constant, loss factor and loss tangent increase with temperature rising at 2.45GHz. Microwave absorption properties of this ore are highly dependent on temperature and frequency. Ilmenite concentrate can be used as raw materials to prepare wideband microwave absorbing material. The research will be helpful in explaining the thermal running of microwave dielectric heating the ilmenite concentrate.IntroductionAs the sources of high-grade titanic mineral are decreasing worldwide, the utilization of low-grade minerals such as ilmenite has attracted more attention [1,2]. Because Panzhihua ilmenite has complex minerals and high contents of MgO, CaO, S1O2 , it is difficult to upgrade the ilmenite to titanium-rich slag and farther produce synthetic rutile and titanium dioxide pigment [3]. Therefore, it is desirable to develop new technology for processing ilmenite ore [4]."

Jan 1, 2012

By Liping Gu, Gordon A. Irons

"A 1/3 scale ""thin-slice"" model of an electric arc furnace was developed so that gas could be injected to simulate foaming gas evolution. The influence of arc jets, oxygen lancing and bottom bubbling was also simulated. Liquid velocities were measured by a white light particle image velocimetry system. Numerical simulations of some of these effects were made using commercial CFD packages. Comparisons with measured results show that considerable care is required to select the appropriate model and to interpret the computational results.INTRODUCTIONDuring recent years electric arc furnaces (EAF) have captured a significant share of steel production, partially due to increased productivity through the introduction of advanced technology such as oxygen injection, slag foaming and long-arc operation, process automation and post-combustion. However, systematic analysis of the process and these effects on heat transfer and fluid flow in the furnace is still in its infancy. Most investigationsl1 6l have been restricted to a specific application such as oxygen lancing or bottom stirring. In addition, it is very difficult to make comparisons between these computed results and experimental/industrial results. In this work a 1/3-scale ""thin-slice"" model of Dofasco's 190 ton EAF was built. The fluid flow in the bath due to the arc jets, bottom stirring, oxygen lancing and CO evolution was simulated. The velocity distributions in the bath were measured using Particle Image Velocimetry (PIV) System. In addition, numerical simulations of bottom stirring and CO evolution were carried out using two commercial CFD packages (Fluent and Phoenics). The objective of this work is to validate the mathematical models so that they can be applied to the full-scale furnaces."

Jan 1, 1999

By Mansoor Barati, Leili Tafaghodi Khajavi

"This study involves employing solvent refining as a purification process in which silicon recrystallization takes place from an iron-silicon melt. It is believed that iron will act as the impurity “getter” and purified silicon crystals will grow from the alloy melt, while the impurities are segregated to the liquid alloy. Phosphorous is a problematic impurity to remove since its segregation coefficient in pure silicon is relatively large. To assess the feasibility and efficiency of phosphorous removal through solvent refining, it is critical to study its equilibrium distribution between solid Si and the Fe–Si alloy phase.The distribution of phosphorous between solid silicon and iron-silicon melt at 1210-1310 °C was measured to evaluate the impurity removal potential of each alloy. Interaction parameter between phosphorous and iron was calculated by varying the concentration of phosphorous in silicon.IntroductionAmong various semiconductor materials for manufacture of solar cells, silicon accounts for over 90 percent of today's PV materials [1, 2].The major challenge in producing solar silicon that operates efficiently is to meet purity level requirement through a cost efficient route. Silicon solar cells can play a significant role in answering the world's need for energy if cost reductions can be achieved through manufacturing process. Considerable effort has been made to replace the expensive, complex vapor-phase purification by a simpler and less costly process. One of the refining approaches that have attracted wide research interests is producing low-cost solar grade silicon by purification of metallurgical grade silicon. Since metallurgical processes are selective in removing impurities, a combination of various purification processes can be used to reduce the impurity level in silicon. Considering different thermodynamic characteristics of impurities, each refining step is responsible for lowering specific impurities."

Jan 1, 2012

By Vincent Canaguier

Methane is increasingly considered as a promising reductant for metal oxides, including chromite. To assess the possibilities of such reduction route, the gas-solid reactions between Ar–CH4–H2 gas mixtures and synthetic chromites are studied between 950 and 1050 °C. The influence of Mg and Al additions on the reduction-caburization of (Fe,Mg)(Cr,Al)2O4 solid solution is investigated thermodynamically, structurally and kinetically. The product phases are examined by x-ray diffraction (XRD), scanning electron microscopy (SEM), and electron probe microanalysis (EPMA). The reaction rate is derived from real-time exhaust gas measurements and post-reaction product analyses such as oxygen analysis. Kinetic models are proposed based on the product phase morphologies and confronted with the empirical data.

By Xianzhong Hu, Qingbo Yu, Qin Qin

"Oxy-fuel combustion is one promising option among different CO2 capture technologies. The object of this work is to show the effect of CO2 dilution on the laminar flame speed, flame structure and reaction pathway for methane oxidation at O2/CO2 atmosphere. In this paper, kinetic simulations were made using CHEMKIN with GRI-Mech 3.0 mechanism, which was validated by experimental data of laminar flame speeds. The reaction pathway of CH4/O2/CO2 mixture was derived from reaction flow analysis. Results showed that CO2 decreased the flame speeds, lowed concentration of major intermediates and increased flame thickness. The major chemical pathways of CH4 to CO2 have not changed at O2/CO2 atmosphere comparing with O2/N2 atmosphere, but contributions to major intermediates formation from each related elementary reaction have changed a lot. In addition, the secondary chemical pathways of CH3 oxidation became different at O2/CO2 atmosphere.IntroductionNowadays, as the global economy is developing fast and the pollutant levels (especially global warming gases) are increasing, a lot of researches are focusing on new technologies which can cut greenhouse gas emissions [1]. New technologies have been developed, such as high Mild combustion, flameless combustion and Integrated Gasification Combined Cycle (IGCC) technology. Oxy-fuel combustion using carbon dioxide as dilution of oxygen is considered as a promising approach for reducing CO2 emission. The properties of CO2 in flue gas are different from N2 in air. On one side, the transport, thermal and radiative properties of CO2 are different from N2 in air. On the other side, CO2 is not inert but directly participates in chemical reactions and recent researches [2-5] also present the chemical effects of CO2 on oxy-combustion. For these differences above, the characteristics of oxy-combustion are not alike with traditional combustion. It is necessary to develop the investigation of oxy-combustion.In all combustion processes, laminar flame speed is an important parameter, which links to combustion behavior. Analysis of this parameter can provide a better understanding of the effect of CO2 dilution in the process of oxy-combustion. Several investigations of laminar flame speeds of oxy-fuel flame have been improved, including experimental measurements and numerical computations. A.A.Konnov et al. measured the flame speeds of oxy-methane and oxy-ethane mixture using the heat flux method with a flat burner [6-8]. V. Ratna Kishore et al. used heat flux method to measure the adiabatic laminar flame speeds of hydrogen [9] and H2/CO mixture [10]. Adiabatic laminar flame speeds of hydrogen in O2/CO2 atmosphere are much smaller than in O2/N2 or in O2/Ar. The burning velocity of H2/CO mixture decreased with increase in CO2 content in mixture. Jeongseog Oh et al. [11] used Bunsen flame to measure the laminar flame speeds of premixed oxy-methane mixture with angle methods in atmospheric condition (300k, 1atm). The results were SL=29.1cm/s and SL=29.5cm/s respectively derived from oxy-methane from CH* images and Schlieren photos."

Jan 1, 2014

By Hannu Johto

Boliden Harjavalta has operated a flash smelter for nickel sulphide concentrates in Finland since late 1959. The original nickel flash smelting process was modified in 1995 to a novel nickel matte smelting (DON) with semi-low iron where the batchwise operated converting became obsolete. Since that, the process has been applied to multiple chemically variable nickel sulphide concentrates with high environmental performance. In this paper, the status of the current smelter operations is described together with the recent modernizations of the nickel flash smelting furnace and the slag cleaning furnaces.

By Hande Cavus, Ibrahim Yusufoglu, Cem Kahruman

"In this study, ammonium tetramolybdate (ATM) was obtained as the intermediate product of ammonium heptamolybdate tetrahydrate (AHM). The thermal decomposition mechanism of ATM was investigated under nonisothermal and isothermal conditions in air and inert gas atmospheres. Nonisothermal experiments were carried out by TGA/DTA/MS while TG was used for isothermal conditions. Characterization of the decomposition products were carried out by XRD and FT-IR. The thermal decomposition of ATM in air proceeds in a single step and forms M0O3 while [(ÍÇ4)2è]ïïï83Ìïè3 and molybdenum suboxide (Ìïè3.÷, ÷=0.025) were obtained in the first and the second steps of thermal decomposition in He, respectively. Activation energies, frequency factors and kinetic model equations were determined for thermal decomposition reactions. Fractional conversion-time diagrams were compared with diagrams drawn according to kinetic model equation.IntroductionM0O3 is usually used as catalyst in industry [1]. AHM is the basic source to produce molybdenum containing catalysts used in petrochemistry [2]. The oxides of Li, V, W, Te, Bi and Sn are doped in M0O3 to produce catalysts, which find commercial applications in the industry. The properties of M0O3 are affected by dissolution, settling, calcination, drying and thermal decomposition processes [1]. There are several studies in the literature about the thermal decomposition of AHM and the characterization of the decomposition products in different gas atmospheres and at various heating rates [3-19]."

Jan 1, 2012