Search Documents

By K. Tozwa

The electrical conductivity of electrolytes for copper electrorefining and electrowinning processes has been reported by many researchers since 1911. The experimental results show that the conductivity increases with an increase in sulfuric acid concentration and decreascs with an increase in copper concentration. In pure copper sulfate solution, however, the conductivity increases with an increase in the copper concentration. After confirming the conductivity of pure and acidified copper sulfate solutions experimentally, the concentrations of hydrogen ion and free (not hydrated) water in the electrolytes were estimated and it was found that the relation between the conductivity of acidified copper sulfate electrolytes and the products of concentration of hydrogen ion and free water is linear. Accordingly, the conductivity of acidified copper sulfate electrolytes increases with an increase in sulfuric acid concentration and decreases with an increase in copper concentration.

Jan 1, 2003

By J. D. Ecuyer, L&apos

he microstructure of galvanneal coatings formed on extra low carbon and interstitial free steel substrates has been characterized using electron microscopy (TEM and SEM) and x-ray diffraction. The coatings are found to consist of a mixture of gamma, delta and zeta phases, of which delta is the main constituent. The amounts of each phase influences the powdering resistance of the coating which was evaluated using reverse Olsen testing and 60" bending. For the three heat input conditions considered, IF coatings were always found to contain a significant amount of gamma and only those which retained zeta phase on the surface exhibited a satisfactory powdering resistance. In much the same way, ELC coatings with relatively thick gamma layers performed satisfactorily only when some zeta was retained. It was also found, however, that coatings with minimal zeta and gamma had an excellent powdering resistance. The latter coatings were produced under galvannealing conditions of lower relative heat input. These results indicate that in addition to the zinc bath composition, coating weight and galvanneal thermal cycle, the base steel chemistry also has an effect on the coating microstructure. Knowledge and control of all aspects of galvannealing is therefore essential to consistently produce acceptable coatings.

Jan 1, 1992

By Miller, Geoffrey W.

The Ravensthorpe Nickel Project (RNP) flow sheet provides for the upgrading of Ni & Co in a size based beneficiation process prior to leaching. The upgrading effect on Ni and Co makes the beneticiation process a powerful addition to the flow sheet. Multiple linear regression (MLR) analysis based on 351 individual batch tests, 52 large scale composites and 21 pilot plant tests has been used to successfully model beneticiation product grade, recovery, upgrade and mass recovery. Statistically, 83% and 96% of the variability in nickel recovery and nickel product grade respectively was accounted for. Algorithms have been developed for Ni, Co, Mg, Al and Fe, which represents the revenue and operating cost factors for the process. The algorithms have subsequently been applied to the resource model, allowing prediction of elemental grade and recovery for the development of the mine schedules based upon these parameters and not head grades alone. This has allowed optimisation of the mine schedule for improvement to the project's NPV. Keywords: Ni Laterite, Prediction, Multiple Linear Regression, Beneficiation

Jan 1, 2004

By Ross R. Bhappu

A theoretical and experimental investigation into pyrometallurgical refining of chloride leach/electrowin copper is described. The two techniques investigated were (i) vaporization and (ii) gaseous halogenation. Experiments were carried out with a packed bed of electrowon copper crystals and a boat of melted copper crystals. Nitrogen gas and Freon 12/nitrogen mixtures were used as the carrier and reac.tive gases. Vaporization was found to be effective in removing Bi, Pb and S while halogenation was effective. in removing As, Bi, Pb, S and Sb. Silver resisted all attempts at removal. Iron was removed but less effectively than the other impurities.

Jan 1, 1985

By Ho-Sang Sohn

The kinetic study on desulfurization of copper matte by gas bubbling was designed under the presumptions of lower FeO activity and of no slag formation, Copper matte with 59% Cu and 22.6% S in weight was oxidized at 1523K by bubbling of Ar + O2 gas through a submerged nozzle. The effects of oxygen partial pressure and flow rate of gas on the oxidation rate of matte were discussed. The desulfurization rate and the evolution rate of SO2 gas of copper matte were significantly influenced by the oxygen partial pressure, but the dependence on gas flow rate was rather complicated. The desulfurization rate and evolution rate of SO2 gas of copper matte were described by the mass transfer rate through the gas film around the rising gas bubbles. Thermodynamic correlation equations between the partial pressure of gaseous species and matte composition were incorporated to the kinetic calculation, The present model shows that the reaction path starts to transiently cross over an isobar line of PSO2 to asymptotically approach to the particular isobar line drawn in a matte composition plane of %S and %O.

Jan 1, 2003

By A. González

Arsenic is one of the main contaminants present in Chilean copper concentrates and its abatement represents a challenge for the process metallurgy, particularly under the strong environmental requirements in the global community. The possibility to form ferric arsenate directly from a gas phase by means of a heterogeneous reaction between an arsenic gas bearing and iron oxide was studied at laboratory scale. A thermodynamical analysis for the system Fe-As-O-S has been initially made, in order to obtain the stability conditions for the ferric arsenate or other FexAs2O2 type compounds. Experiments were made using an hematite sample suspended in a thermogravimetric device. AS4O6 gas generated from solid AS203 that was passed through the iron oxide sample and its instantaneous weight change was recorded directly. A kinetic study for the AS4O6 volatilization was made to control the gas composition. A chemical control between 300 and 600°C with an apparent activation energy of around 14 Kcal/mol As2O3 was determined. The samples after the reactions were chemically and XRD analysed. Arsenates detected corresponds to complex compounds. Results shows a dependence on temperature and oxygen content in the gas phase. The kinetics for iron arsenates formation is slow, reaching an arsenic capture of 6% after 80 minutes of reaction when an oxygen content of 50% is fed continuously at 800°C and 3,56% As in the gas. Experiences made at the same temperature but under higher oxygen content in a closed reactor, allowed arsenic capture close to 60%. For higher temperatures the capture is considerably lower.

Jan 1, 2003

By K. Adham

For use in many existing and emerging applications, the purification of natural graphite is required to achieve +99.9% carbon content with minimum metallic impurities. Currently, the hydrofluoric acid process is used, which carries certain environmental and workplace health and safety impacts. While thermal purification of graphite at temperatures over 2500 °C is a known alternative, such high-temperature furnaces are expensive to build and operate. Using chlorine at lower temperatures to purify graphite is also known and patented, but is currently limited to treating solid synthetic graphite shapes in small-scale batch furnaces. Chlorine treatment of natural flake graphite resources can be used commercially, if certain drawbacks are addressed through process improvements that can be helped with the use of fluidized bed reactor technology.

By Jonkion M. Font

Due to the known disadvantages of the use of iron silicate slag in the nickel converting stage, i.e., high metal losses, high magnetite content, and low fixation of impurities in the slag, the development of the new proposed "ferrous calcium silicate slag" for smelting and converting processes of nickel is very promising. Hence, considering the successful experimental results of using CaO base slag for the nickel smelting process, a study based on a detailed comparison for the phase equilibrium, and the minor elements distribution between the Ni3S2-FeS matte with either FeOx-CaO or FeOX-Si02 base slag was investigated. The main results are summarized as: no difference in the nickel losses between both slags was found at high nickel content in the matte, and the fractional distribution analysis for arsenic and antimony pointed out their preferential fixation in the calcium ferrite slag rather than in the iron silicate slag. Considering the energy and pollution issues, the technical feasibility of using calcium ferrite slag in a converting process of the Bessemer matte will have a prominent future for the nickel industry.

Jan 1, 2003

By Sergio N. Monteiro

Polymeric matrix composites reinforced with coir fibers are being used in many industrial applications such as automobile interior panels and cushions. These composites have relatively low mechanical strength due to the weak fiber/matrix interface. The objective of the present work was to investigate the effect of a surface alkali treatment of the curaua fiber on the mechanical behavior of polyester composites with different amounts of these fibers. The treatment, also known as mercerization, was performed with distinct concentrations, 0.1 and 10% of NaOH at 1 min and 1 hour, before incorporation of the coir fibers into the polyester composite. The results showed no significant change in comparison to similar untreated coir fiber composites. A microstructure analysis revealed that, in addition to reducing the hydrophilic characteristic of the fiber,the treatment also affects the surface morphology and impairs the fiber/matrix interfacial strength.

Jan 1, 2009

By Nagahiro Saito, Takashi Nishimura, Takamichi Ichikawa, Akio Fuwa

"Yttria-stabilized zircohia (YSZ) has high potential to be used as solid-oxide fuel cell (SOFC) electrolyte. However, the high efficiency of SOFC has not been yet achieved due to the high internal resistance of bulk electrolyte. The resistance becomes lower with the decrease in the electrolyte thickness. Thus, the decrease in electrolyte thickness leads to lower internal resistance. . The aim of this study is as follows: (a) to prepare the thin films of YSZ by inductively-coupled RF plasma-enhanced metal organic chemical vapor deposition (PEMOCVD) process using Zr(t-OC4H9)4,Y(DPMh and oxygeil, and (b) to reveal the relationship between the structural characterizations and the process parameters.1. IntroductionYttia-stabilized zirconia (YSZ) has, been widely used as not only heat-resistant materials but also the components in automotive oxygen sensors, electrolytes of solid-oxide fuel cell (SOFC)(1)(2) and the buffer layers for the high-temperature superconductor because of its low thermal conductivity, good mechanical properties and high ionic conductivity. However, it is said that the internal resistance of the bulk electrolyte is too high to be appropriate as a solid electrolyte for high-efficient SOFC. The authors believe that the thin YSZ electrolyte can give a high performance to characteristics SOFC, since the internal resistance becomes lower with the decrease of electrolyte thickness. Thus the process technology to prepare YSZ thin films is desirable and must be established.In recent years, the YSZ thin films have been reported by chemical vapor deposition (CVD), thermal CVD using metal chlorides (MC) of ZrCl4 and YC(3)(4), thermal CVD using metal organic compounds (MO)(5)(10) Zr(t-OC4H9)4 and Y(C11H19O2)(11) and plasma-enhanced (PE) CVD using MO. Here, these methods are called MCCVD, MOCVD and PEMOCVD. MCCVD has two disadvantages; a large quantity of chlorinated impurities in deposited films and high processing temperature (> 1273K). This high processing temperature leads to damage of substrates in particular, so the application of this technology is limited. On the other hands, the processing temperature by MOCVD becomes and is lower. Unfortunately, the accurate vapor pressures of these metal organic compounds have not been, known so: that it is difficult to control the composition and the film thickness by MOCVD method well. Moreover, the large amount of carbonic compounds in the films prepared by MOCVD method is produced. However, plasma-effect has been reported to decrease large amount of the carbonic impurities by PEMOCVD. However, PEMOCVD has many reaction parameters in plasma processing; the geometry of experimental apparatus, radio frequency, electronic power input and so on. Thus, the general understanding about the relationship among reaction parameters, the composition and crystal structure of thin deposit film by this method has not yet been established."

Jan 1, 2000

By C. P. Manning

This paper reports recent progress in the development of a unique metal extraction technology utilizing zirconia-based inert anodes for the electrolytic reduction of metals from their oxides. In this process, the target metal oxide is dissolved in an ionically conducting liquid solvent phase. An extended anode consisting of an oxygen-ion-conducting stabilized zirconia membrane in intimate contact with a catalytically active electronic phase and an inert electronically conducting cathode are inserted into the molten flux containing the oxide. When the appropriate electric potential is applied between the electrodes the target metal is reduced at the cathode and oxygen ions are selectively transported across the stabilized zirconia membrane and oxidized at the anode. When the process is conducted at temperatures between 1200-1400°C, the ohmic resistance drop across the stabilized zirconia membrane is low, and high current densities on the order of I A/cm2 or greater can be obtained. In addition, the process efficiency can be increased further by directly reforming hydrocarbon fuel over the anode. Laboratory experiments at Boston University have demonstrated the technical viability of employing zirconia-based inert anodes for environmentally sound production of metals such as magnesium, tantalum, aluminum, etc., directly from their oxides. Significant progress has been made in the application of this concept to the electrolytic reduction of magnesium at 1300°C. The research topics covered include stability of the zirconia membrane in the selected molten solvent (flux), volatility of the flux, electrochemical characterization of the electrolytic cell, and analysis of the metals produced.

Jan 1, 2003

By G. L. Fredrickson, T. A. Johnson, B. R. Westphal, J. C. Wass, S. X. Li, D. Vaden

"Recovery of uranium from the Mk-IV and Mk-V electrorefiner vessels containing a LiCl/KCl eutectic salt has been on-going during the pyrometallurgical processing of used nuclear fuel for 14 and 12 years, respectively. Although austenitic stainless steels are typically utilized for LiCl/KCl salt systems, the presence of cadmium in the Mk-IV electrorefiner dictates an alternate material. A 2.25Cr-1Mo alloy (ASME SA-387) was chosen due to the absence of nickel in the alloy which has a considerable solubility in cadmium. Using the transition metal impurities (iron, chromium, nickel, molybdenum, and manganese) in the electrorefined uranium products, an algorithm was developed to derive values for the contribution of the transition metals from the various input sources. Weight loss and corrosion rate data for the Mk-V electrorefiner vessel were then generated based on the transition metal impurities in the uranium products. To date, the corrosion rate of the 2.25Cr-1Mo alloy in LiCl/KCl eutectic is ""outstanding"" assuming uniform (i.e. non-localized) conditions.IntroductionLow-enriched uranium products are being recovered from the Experimental Breeder Reactor-II (EBR-II) and Fast Flux Test Facility (FFTF) used nuclear fuels by a pyrometallurgical treatment process at the Idaho National Laboratory (INL). The treatment process comprises a set of operations designed to neutralize bond sodium, recover uranium from radioactive fission products, and place the fission products into acceptable waste forms [1-2]. Reactive sodium metal, essential for heat transfer purposes during reactor operations, is readily converted to chloride during the process. Electrorefined uranium products are currently being stored pending a final disposition decision. Treatment of the EBR-II used driver fuel was initiated in June 1996 while blanket fuel processing started in September 1998. These treatment processes continue on the balance of the used fuels."

Jan 1, 2011

By Takeshi Yoshikawa, Kazuki Morita, Kunitoshi Matsunaga

"In metallurgical grade silicon (MG-Si), most impurities mainly exist at the grain boundaries and distribute in silicon grains at extremely small contents. Grain boundary phases in MG-Si transform into liquid above the eutectic temperature, and migrate towards high temperature regions when heated under a temperature gradient. With the migration of all liquid phases in MG-Si to the surface, the impurity contents will be decreased less than their solubilities in principle.In the present work, the fundamental research was conducted to discuss the possibility for purification using the liquid phase migration technique. The purification limit was estimated by thermodynamic calculations, and metallic impurities were estimated to be effectively removed except for Fe and Al. The migration behavior of the liquid phase in the synthesized silicon substrate was investigated by unidirectional heating under infrared radiation at 1523-1548 K, and the proceeding of migration was confirmed. The migration velocity was 1.4--2.0xl0-7 mis, and found to be controlled by the liquid phase diffusion.IntroductionPhotovoltaic energy is one of promising energy resources in a sustainable society because of its inexhaustibility and cleanliness. Although the production and installation of solar cells have increased significantly during the last decade, the cost of solar cell installation is still high. To enable the widespread use of photovoltaics and for the photovoltaic electricity price to reach grid parity, a low-cost and abundant feedstock of solar grade silicon (SOG-Si) is essential. Recently, a modified Siemens process and a fluidized bed reactor process were developed to address the cost and energy issues associated with the conventional Siemens process. However, their cost reduction potential is limited because of the large energy consumption needed to convert silicon into gaseous compounds. Purification of silicon through metallurgical routes offers a promising way for producing SOG-Si from metallurgical grade silicon (MG-Si), because it enhances productivity and can also lower the process costs. Although several metallurgical processes such as directional solidification [l ], vacuum refining [2-4] and plasma oxidation [5-7], have been developed, processing times and refining efficiencies still have to be optimized."

Jan 1, 2013

By A. J. Maselli, E. C. Cemak

Hartford Steel Technologies (HST) has a pyrometallurgical and hydrometaliurgical process capable of reclaiming valuable metals from a hazardous waste· stream such as EAF Dust. The HST Process effectively addresses the growing environmental concerns surrounding the increasing production of EAF Dust without producing any hazardous waste material as byproducts. Currently EAF Dust production levels are exceeding the 1,000,000 metric tons per year mark. The HST Process is designed to separate iron, zinc, lead, cadmium, copper, and silver metals using a two-phased process. The Pyrometallurgical side of the Process utilizes a Rotary Hearth Furnace to separate the iron metal from the remaining metals. These remaining metals are further separated, using a Hydrometallurgical Process, in a series of digestion tanks. The individual metals are then collected in saleable form.

Jan 1, 2000

By Wanderson Silva Rodrigues, Paulo Adão Marinho dos Santos, José Antonio Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo

"1 AbstractThe production of alumina from bauxite using the Bayer process generates 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. This material has no large scale current use and is usually stored. This paper shows that it can be used in a suspension with water as a gas effluent cleaner with high efficiency to remove SO2. It can substitute other materials currently used reducing the overall environmental impact and potentially reducing the cost of gas treatment.2 IntroductionThe production of millions of tons per year of alumina around the world generates from 0.7 to 2.0 ton of the residue known as red mud per ton of alumina. The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity this material is considered dangerous and currently there is no operating process capable of reuse all the material produced at any refinery. These lakes after filled of solid material eventually have the surface revegetated. In any cases they will remain as an environmental passive and need monitoring for decades. The search of industrial processes that combine the cleaning of gas effluents emission and reuse of these residues can contribute to the reduction of the overall impact of the alumina production process.The main objective of this work is to study the efficiency of the red mud as alternative raw material for the control of emissions of SO2 in combustion gases. Usually this is made through alkaline solutions of CaCO3 or NaOH in absorbing equipments like spray towers or packed column. This project main objective is to study the reaction of the SO2 with a suspension of red mud and water in order to obtain the basic parameters to design equipment capable of process this reaction on a pilot scale. With that goal compositions of red mud on spray were processed with flow of gas containing SO2 with concentration similar to the exhaust gases of the combustion process of the refineries."

Jan 1, 2011

By Yuzhe Zhang, Xiaodi Huang, Xinli Wang, Bowen Li, Matthew Andriese, Jiann-Yang Hwang, Zhiwei Peng, Likun Li

With the development of the world, the waste tires have been a serious environmental problem. There are about 2 billion waste tires produced all over the world every year and about 500 million waste tires are produced in the United States. Most of the waste tires are land filled, which waste a lot of space. It takes hundreds of years to resolve the macromolecules of waste tire into the standard which does not pollute the environment. Microwave irradiation is a thermal processing way for waste tires decomposition. In this study, the relative dielectric loss factor of the tire at various temperatures was determined to understand the behavior of tires under microwave heating.

Jan 1, 2016

By René Winand

Due to chemical and electrochemical behavior of the most common additives in copper electrorefining i.e. gelatine, thiourea and chloride ions, it is essential to simulate as far as possible true industrial practice while performing laboratory experiments. The three additives must be studied simultaneously, and added continuously to the electrorefining cell. Ratio electrolyte volume to cathode area; ratio bleed flow to cathode area; hydrodynamic conditions; residence time of electrolyte in the cell; current density; electrolyte and soluble anode must be as near as possible to industrial ones. Experiments performed in the author's laboratory show that under these conditions, reproducible results can be obtained at normal industrial current density and at high current density as well. Problems are however still encountered when developing a sensor for additives monitoring, due to electrolyte redox potential and to substrate influenced thin layer deposition.

Jan 1, 1995

By A. Rios

ENAMl's Paipote Smelter commenced operations in 1951. At present, it processes 230,000 tonnes/year of green feed in a conventional smelter, which comprises one reverberatory furnace, two Hoboken, one Peirce-Smith converters and one rotary anode furnace. The feed is composed of 83% copper concentrate and 17% metallic copper precipitates, which results in a feed average grade of 32% of copper content. The final products are 75,000 tonnes/year of copper anodes and 48,000 tonnes/year of sulphuric acid. At present, the plant is undergoing a modernization to expand the smelter capacity to 300,000 tonnes/year of green feed and increase the sulphuric acid production to 100,000 tonnes/year. This will be achieved with the installation of an El Teniente Converter and an expansion in the acid plant. The work began in November 1991 and is scheduled to be in operaton by March 1993. The paper provides an overview of the modernization plans and results achieved to-date.

Jan 1, 1993

By G. Cifuentes

The kinetics of the electrolytic oxidation of cyanide to cyanate on PbO2-coated stainless steel anodes have been studied by both experimental and theoretical means. The anodes were based on 316 steel and performed in a satisfactory fashion. The pH of the studied KCN solutions exhibited a constant value about 11. Values for all the kinetic parameters have been determined and a mechanism for the studied reaction is proposed.

Jan 1, 1999

By Lev Levin, Sergei Lesokhin

"The formation of titanium carbide during hot filament assisted carburizing of NiTi alloy was investigated. Phase content and morphology of the diffusion zone were examined by X-ray diffraction, X-ray microanalysis, SEM, and Auger electron spectroscopy. The growth of stable and adherent TiC film was observed. A non-planarity of interphase boundary was noticed. The applicability of the chemical diffusion approach to the analysis of the experimentally observed interface instability is discussed. A criterion, taking into account the influence of growth stresses on the stability of the flat interface, is developed by means of linear perturbation analysis.Introduction.Equiatomic intermetallic NiTi belongs to a class of materials exhibiting the shape-memory effect. The unusual property of this compound promotes its application in many fields, from aerospace technologies to medicine. The relatively high ductility ofNiTi also permits its use as a matrix material in metal-ceramic composites. The objective of this work was to investigate the possible incorporation of a ceramic material (titanium carbide) into NiTi by gas carburizing.Free energy calculations indicate the potential to obtain TiC by carburizing Ni-Ti binary phases. The main obstacle to such a process is the high affinity of titanium to oxygen. At moderate temperatures the formation of TiC is preferable to titanium oxidation only if the partial pressure of oxygen is extremely low [1]. This problem was overcome in this work by the use of hot filament assisted gas carburizing. Due to chemical reactions occurring near the hot filament, the gas mixture, initially consisting of methane and molecular hydrogen, was enriched by atomic hydrogen [2], drastically decreasing the content of free oxygen in the carburizing atmosphere.The second part of this article concerns the theoretical analysis of reasons that lead to the development of the experimentally observed morphology of the diffusion zone. In particular, the influence of the growth stresses on the morphology of an interphase boundary is investigated."

Jan 1, 1996