Search Documents

By Min Chen, Nan Wang, Zhen Tian, Yingying Shen

"The enrichment behavior of phosphorus in CaO-SiO2-FeOx-P2O5 slag was studied by making an investigation on the distribution of phosphorous content in slag and 2CaO·SiO2 phase. The research results showed that the existing 2CaO·SiO2 solid particles in slag were the sites for the phosphorous enrichment. The enrichment process of phosphorus in CaO-SiO2-FeOx-P2O5 slag can be recognized as: mass transfer of phosphorus from bulk slag toward the surface of 2CaO·SiO2 particle, superficial dissolution reaction of phosphorus to 2CaO·SiO2 and diffusion of phosphorus through the product layer of 2CaO·SiO2-3CaO·P2O5 solid solution to the inner of 2CaO·SiO2 particle. Compared to the 2CaO·SiO2 particles with larger size (500µm to 1000µm), the completion time of enrichment was shorter for the particles with smaller size (less than 50µm).IntroductionDuring ironmaking and steelmaking, significant amounts of slag are produced. Contrast to the high utilization of ironmaking slag, the treatment of steelmaking slag is more difficult and challengeable, and therefore, an alternative approach is to recycle the steelmaking slag inside the ironmaking and steelmaking process itself. The main limitation to the reuse of steelmaking slag inside the process is that the refining process may be aggravated caused by the phosphorous accumulation if it is used in the blast furnace burden [1]. At the same time, the phosphorous content of steelmaking slag (approximately 1%~5% P2O5) is too low for it to be used as raw material for fertilizer [2, 3]. Moreover, owing to the diminishing supply of global iron ores with low phosphorous content, the control of phosphorus in iron and steelmaking processes has become an increasing problem, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. Therefore, a valuable approach is quite appreciated in which the steelmaking slag is recycled within the ironmaking and steelmaking process and at the same time, the high phosphorus-containing phases in the steelmaking slag, suitable for use as fertilizer can be separated and recycled effectively [4]."

Jan 1, 2011

By L. J. Friedman

Smelter operating and environmental requirements demand high on-stream time (high reliability) from the primary smelter sulfur retention device - the sulfuric ?acid plant. The key to reliable smelter sulfuric acid plant operation is the gas cooling and cleaning system. Problems in the gas cleaning system cause corrosion, plugging, equipment failure, etc - plant down time, in the contact section of the plant. The last fifteen years have seen major changes in gas cleaning system design _to the current standard of brick lined venturi scrubber, packed gas cooling tower with plate type liquor coolers and lead or plastic tube precipitators, The current? design offers improved' impurity scrubbing along with increased reliability. in addition, a number of alternate gas cleaning systems have been offered Chemetica LAB System; Monsanto DuPont D:Jna-Wave Syatem1 Lurgi venturi scrubber with lead star gas cooler. This paper will review the design and operating advantages, disadvantages, and risk of the standard gas cleaning system and compare it to the alternate systems. _

Jan 1, 1992

By Kenneth L. Driggs

The Environmental Protection Agency's Clean Air Act of .1970 provided the driving force for the current Magma Smelter configuration. The historical and technical perspectives of those process developments are reviewed. Innovations in procedures and equipment have allowed compliance with the requirements of the regulating authorities. The wet scrubbing of converter gasses and the monitoring of converter operations by a controlling foreman are two of the major contributors to these successes. The Clean Air Act Amendments of 1990 have posed many new concerns for all U.S. industry, including the few (seven) primary copper smelters remaining. Future concerns include tightening the sulfur dioxide ambient standard from the current three-hour averaging period to one hour"

Jan 1, 1992

By Rodney Hundermark, July Ndlovu, Lloyd Nelson, Phillimon Mukumbe, Paul van Manen, Whitey Seyanund, Bart Pieterse, Bertus de Villiers, Diale Mokwena

The 2003 redoubling in power to 68MW on the Polokwane Smelter furnace represented a significant intensification in platinum group metal (PGM) smelting. Combined with onerous ‘green’ PGM concentrate smelting requirements, this yielded conditions unusually corrosive to copper coolers and refractories. This presented unexpected operational and design challenges to reliable crucible operation and maintenance. Combined with specific operational control intervention, development of protective coatings has led to the life of water-cooled copper components improving from 9 to 40 months. The furnace matte endwall was extended in 2010 to address accelerated wear of refractories and the potential risk for contact of copper components by superheated matte. An 18 month planned endwall rebuild cycle has been demonstrated (versus catastrophic failure within 9 months). Finally, benefits including lower energy consumption, improved metal recoveries and higher productivity resulting from operational and in-house design developments will be described, that justify “Celebrating the Mega-scale” in PGM smelting.

Jan 1, 2014

By Peter Stiaszny, Andrej Samoilov, Yuri Titovets, Gottfried Hribernig, Nikolai Zolotorevskii

"The model has been developed to simultaneously predict both transformation product portions and mean ferrite grain size from the same common · principles as a result of the austenite decomposition during any cooling path of dual phase steels. The transformation products considered are polygonal ferrite, pearlite, bainite and martensite. The model is based on the classical equations of nucleation-growth theory and also contains some empirical parameters. The chemical driving forces for nucleation and composition of elements at the phase interfaces are derived by computation thermodynamics. The empirical parameters related to the model were determined on the basis of a series of austenite transformation dilatometric curves and grain size measurements for continuous and interrupted cooling of several steel types. The model is aimed to predict phase transformation in the complex cooling conditions of the run-out table of the hot strip mill at YOEST-ALPINE STAHL LINZ GmbH as a part of the computer aided system for prediction and on-line controlling of the mechanical properties of hot-rolled strip.IntroductionThe term ""dual phase steels"" is used to refer to a steel consisting essentially of a dispersion of martensite in a fine-grained ferrite matrix. These steels are of increasing technological interest since they provide a better combination of strength and ductility than any other conventional steel sheet material. The strength is important because it offers an opportunity to produce lighter components, while good ductility is needed to permit easy forming of components. It is generally recognized that martensite plays an important role in determining the strength level of dual phase steels. A full understanding of the role played by the phases in determining such characteristics requires investigating in more detail how to optimize the martensite level of such steels, while maintaining good ductility remains the subject of continued research in the industry."

Jan 1, 2000

By T. Shoji

"The human history is characterized by social development based on mineral and energy resources, and many conflicts to take the resources by power. This is shown by not only world wars but also many local conflicts as well as international supremacy.IntroductionThe world population after B. C. 10000, which is summarized in several papers, is approximated by four straight lines on a semilogarithmic diagram as shown in Figure 1 [l]. The annual rates of increasing are 0.0041, 0.071, 0.53, and 1.85 % from the old and young periods. The boundaries among four periods are approximately B. C. 4600, AD. 1670, and 1930. The start of the second period seems to correspond to the beginning of agriculture and cattle breeding. Precisely speaking, the usage of natural energy resources such as woods and domestic animals already began, but is inferred to have become common after the age. The third and fourth periods are characterized by the common usage of coal and oil, respectivety. Not only energy resources but also mineral resources including gold, copper, iron and others are also important for the human history.Mineral and energy resources have supported the development of the .human civilization, and have caused many conflicts because of this reason. Every day newspapers report conflicts, such as Chechnya, East Timor and Ache. We can easily point out the facts that the conflicts closely relate to mineral and energy resources. Groznyj, Capital of Chechnya, is located on the western margin of Caspian oil field. Many mineral deposits occur in Kavkaz Mountains running south of Chechnya. Subsea oil fields occur in Timor Gap located between East Timor and Australia. Ache is also one of oil fields in Indonesia. It is very difficult to state present conflicts independently of a political view of point. For this reason let us try to historically review the relation between mineral and energy resources and international domination and conflicts [2] based on many papers [3]."

Jan 1, 2000

By Yousef Mohassab, Feng Chen, Hong Yong Sohn, Mohamed Elzohiery

The determination of reduction degree in a DR process is sensitive to the total iron in the ore and DRI. An accurate and high throughput analysis method for total iron has been developed. Titration of the solution after tin(II) chloride reduction of ferric ion is a widely used method for iron analysis. However, it is a multistep method that requires many chemical reagents and much time. In this work, an ICP-OES analysis method with higher or equivalent accuracy compared with the titrimetric method was developed. This method has much higher throughput and demands fewer chemical reagents compared with the titrimetric method. In this paper, a comparison of the two methods is presented.

Jan 1, 2016

By S. Neven

The smelting of copper anode slimes, a material which contains mostly lead, silver, copper and selenium, has been practiced for many years with a view to recovering the silver and associated small amounts of gold. However, a theoretical understanding of the process has been lacking and this handicaps efforts to improve and intensify smelting operations. In the past few years work has been done in this area and this work will be reviewed in the paper. The underlying thermodynamics of the oxidation of silver-copper selenide mattes has been developed and used as a basis for the construction of a computational thermodynamics model which attempts to predict the composition of all condensed phases during the course of smelting. The model will be outlined and its successes in matching experimental data, as well as its current deficiencies, will be considered. Supporting work on the thermodynamics of silver solubility in slags, on activity-composition relationships in the Ag-Se system and work in progress on the oxidation state of copper in the slags will be reviewed. These projects are designed to provide further detailed data which will improve the robustness of the thermodynamic model.

Jan 1, 1999

By Norihisa Iida, Yutaka Koshiba, Tsutoipu Masui

"Mitsubishi Materials has many years of experience in the production of oxygen free copper (OFC) and its alloys with a fully continuous-casting process. Four grades of OFC, commercial, electronic, superconductor, and ASTM class I are available according to user needs such as stabilizer for superconductivity, magnetron, and ultra-vacuum systems. Along with Cu-Ag and CuSn, we offer OFC based copper alloys such ·as Cu-Cr-Zr, Cu-Fe-P, Cu-Ni-Si and others, that are suitable for lead frame and connectors. Within the maximum sizes of 260mm X 1050mm for cakes and 385mm diameter for billets, we are very flexible and can adjust the ingot size to customer’s requirements. Other products that we can supply are semi-finished products such as hot rolled sheet, ·forged blank, extruded rod and finished products like mold for continuous casting of steel, ring mold for non-ferrous casting and backing plate for sputtering target.IntroductionMitsubishi Materials Corporation developed mass produced high quality oxygen free copper and. high copper alloy ingots in the 1960's. We produce 60,000 - 70,000 tons annually giving us 22 - 23% share of the world's market.Our oxygen free copper and. copper alloys are produced with a fully continuous casting process using only high-grade copper cathodes from our Naoshima and Onahama refineries. The raw material is melted and cast in' a carefully controlled atmosphere resulting in a product with low impurities and excellent properties.Using a controlled atmosphere it is possible to produce high quality copper alloys including active elements like chromium (Cr), zirconium (Zr), titanium (Ti), and magnesium (Mg) which are difficult to produce using standard batch casting methods.Using our own cakes and ·billets we produce and supply worldwide wrought materials like molds for ferrous and non-femous casting. These products receive special patented thermo-mechanical· treatments resulting in high strength and excellent conductivity with low cost."

Jan 1, 2000

By Xuling Chen, Yi Wang, Xiaohui Fan

"The current control method of grate-kiln iron ore oxide pellet production is lack of accuracy and normalization due to the limited detection conditions. Therefore, mathematical models of grate-kiln temperature field are presented. With calculation of gas-particle heat transfer as well as enthalpy changes of moisture evaporation and magnetite oxidation, the thermal history of pellets throughout grate-kiln process can be acquired and used for production status estimation. Taking the calculated results as well as detected data in production as inputs, process parameters such as running speed, fan opening and coal injection rate as adjusting objects, expert system for grate-kiln pellet production is outlined. And the preheating section dominated control strategy is explained. Results of production application show that the stability rate of gas temperature in gas hood of preheating section is increased from 91.0% to 94.2%, compressive strength and first grade rate of pellet are increased by 3.62% and 2.36%, respectively, while FeO content is 18.18% lower. Control guidance of this expert system can solve production anomalies effectively, stabilize grate-kiln iron ore oxide pellet production and improve pellet quality.IntroductionSteel industry in China has developed rapidly in recent years. China’s crude steel production in 2010 is nearly 627 million, which is 44.2% of the world total production. Burden with higher quality is demanded by enlargement and modernization of blast furnaces. And oxide pellet production has become a growing concern. In 2010, the total production of pellet in China is 110 million, and about 60% is produced by grate-kiln process."

Jan 1, 2012

By Orlando C. Rojas

The Potrerillos Smelter commissioned a new El Teniente converter in 1985. As a result of the use of this technology, the Peirce-Smith converters have been processing only high grade matte or white metal. These operational changes resulted in damages to the converter shells, excessive splashing and cold dope generation and very short refractory campaigns. The paper shows the modifications to the tuyere angle, mouth design changes and new techniques for mouth cleaning and gas handling. Operational results up to 1991 are also shown.

Jan 1, 1993

By Satu Strömberg

A single-particle laminar-flow technique was used to study oxidation of two nickel concentrates and a granulated nickel matte (43 wt% of Ni). Experimental conditions were: reaction gas from N2 to N2 + 75 vol% O2; gas preheating temperatures ranging from 500 to 1100°C. The major nickel-bearing minerals in the two concentrates were pentlandite and violarite, respectively. Chemical analysis of the particles was used to determine the oxidation degree of the materials, and optical and scanning electron microscopy were used to detect their morphology and mineralogy. Total desulfurization of the nickel concentrates was achieved under the most oxidizing conditions, while the sulfur removal from the nickel matte was not as efficient, especially with the coarse size fraction. Pentlandite-based concentrate was found to be less reactive than the violarite-based.

Jan 1, 1995

By Vaughan R. Voller

"Solidification systems from conduction controlled freezing of a pure material through to alloy phase change that include flow and segregation processes are described. The components in a general solidification model-variables, governing transport equations, and local scale relationship-are outlined. A central focus is the presentation of an explicit procedure for coupling between macroscopic and local scale variables.IntroductionSince the seminal work of Byres et al.[!] in the 1940's there has been a steady progress in modeling solidification systems with increasing levels of complexity. The object of this paper is to track the evolution of these solidification models and present a general modeling approach that applicable to a wide range of the solidification systems of current interest.Solidification SystemsIn a broad sense the underlying physics in a solidification process occur at two distinct length scales:1. The macroscopic scale of the process over which the governing transport equations of heat, mass and momentum hold.2. The local scale at the solid-liquid interface where the solidification phenomena are operative."

Jan 1, 1999

By Guo Xueyi

The electrochemical couple behavior of manganese dioxide with ferrous/ferric ions in acidic chloride medium was investigated, It was proven that the dissolution of Mn01 is due to the electrochemical couple reaction between MnO2/Mn2+ and Fe2+/lFe3+ in the solution, The driving force for the process originates from the rest potential difference of the two couples. The reduction of Mn02 is controlled by clectrochemical kinetics, whereas the conversion of F e2+ to Fe3+ is limited by diffusion, The factors such as the Mn2+, Fe2+, Fe3+, Cl concentration, pH of the solution and the temperature, have much influence on the kinetics of the couple process, This study will be useful to elucidate the mechanism for the leaching of manganese nodule from the deep ocean as well as manganese dioxide ores in land,

Jan 1, 2003

By Yuan She, Qihang Liu, Keng Wu, Hailiang Ren

By observing different coal char’s microstructures and microscopic morphologies during the coking process, the characteristics of COREX coal char’s microstructure and properties were analyzed. MCRI and MCSR were used to respectively describe the reactivity and the strength after reaction of coal char, with those of BF’s coke for reference, and then the physical meaning of MCRI and MCSR were given. MCRI and MCSR were determined by the composition of coal char. For the two kinds of COREX coal, the formula to forecast the hot performance of coal char was set up by making a multiple linear regression between the hot performance and microstructure of the coal char at 1100℃, and the predictive values of coal char’s hot performance at 600℃, 800℃ and 1000℃ coincided well with the measured values.

Jan 1, 2015

By A. McLean, S. Dawson, N. D. G. Mountford

"IntroductionIn order to predict the accepted industrial practice for the year 2000, it may be helpful to first consider the rate of development of scientific knowledge. If the speed with which man can travel on commercial vehicles is taken as a criterion for determining the rate of progression, then it can be seen from Figure 1 that advancement in our present century is very rapid. Likewise, if computer technology is used as a criterion for the measurement of scientific advancement, it becomes evident that technological evolution can be highly exponential. These two examples are sufficient to demonstrate that engineers and managers cannot afford to regard scientific development as being linear with respect to time if they are to avoid underestimating the needs of society.Within this framework of overall development, the time required for individual ideas to progress from inception to regular application has decreased considerably. For example, X-rays first discovered by Roentgen in the 1890's and now used widely in medicine and engineering, required a developmental period of some eighty years. The motorcar evolved from early beginnings at the turn of the century to a position of great social impact in sixty years. Rectifier materials used in high frequency radar to the present explosion in communications, required forty years. As illustrated in Figure 2, the period is shortening rapidly.The use of sound waves appears to be following a similar path. There is now a considerable body of knowledge concerning their behaviour and exceptional advances have been made. In medicine and engineering the sonic approach to examination is well established, and acoustic testing forms the basis of several diagnostic and quality control applications. With respect to metals engineering, ultrasonic testing has contributed to the understanding of the relationship between the size and number of internal defects and the probability of premature failure. This has allowed the designer to incorporate appropriate safety factors in his designs; but more importantly, the realization of the deleterious effect of inclusions on the performance of the final product has resulted in a continuous pressure on the material suppliers to reduce the number of defects in their products.It is not only the designer who is demanding defect free material but also the fabricator, as material breakdown during manufacture can be prohibitively expensive. Examples of this can be found in both the aluminum and steel industries where ultra clean sheet is required to ensure that rejections are minimized during beverage can manufacture and other deep drawing operations."

Jan 1, 1988

By R. G. Robins

The effective removal of arsenic(V) from process streams and waste waters by precipitation with excess iron(II1) is sometimes attributed to the formation of basic ferric arsenates. The authors have investigated this system extensively using a variety of techniques and conclude that the solid phase produced is iron(II1) oxyhydroxide (ferrihydrite) with arsenic(V) adsorptively bound to the 2-3 nm particles.

Jan 1, 1992

By Kenneth L. Driggs

The Environmental Protection Agency's Clean Air Act? of 1970 provided the driving force for the current Magma Smelter configuration. The historical and technical perspectives of those process developments are reviewed?. Innovations in procedures and equipment have allowed compliance with the requirements of the regulating authorities?. The wet scrubbing of converter gasses and the monitoring of converter operations by a controlling foreman are two of the major contributors? to these successes. The Clean Air Act Amendments of 1990 have posed many new concerns? for all U.S. industry, including the few (seven) primary copper smelters remaining. Future concerns include tightening the sulfur dioxide ambient ?Standard from the current three-hour averaging period to one hour.

Jan 1, 1992

By Evan O. Jones

Processes involving distillation under reduced pressure were developed at the Pacific Northwest Laboratory several years ago to recover spent acid solutions generated during the manufacture of nuclear fuel for the N-Reactor at the Hanford site. Following construction and testing of a pilot-plant, the technology was licensed to Viatec Recovery Systems, Inc. for commercialization. The technology developed included specialized distillation and rectification of volatile acids, removal of water and/or volatile acid from sulfuric acid, and precipitation of salts. A key feature of the Waste Acid Detoxification and Reclamation (WADR) technology is the development and use of advanced thermoplastic and fluoropolymer materials of construction in all critical process equipment. The technology was then expanded to include crystallization to recover metal salts for possible reuse. Economic and environmental advantages of the procedures include recovery of acids for reuse, simplification or elimination of the disposal of waste solutions, and possible recovery of metals. Industries expected to benefit from such applications include galvanizing, electroplating, sand leaching and any where metals are cleaned in acid solutions. Currently a modular system has been assembled for recovery of several different spent acid solutions.

Jan 1, 1995

By D. G. Mason

During the design of copper refinery tankhouses, there is a need to develop mass balance calculations for many process components, so that optimum physical plant configuration is achieved. Each mass balance is complex, possibly with over 120 interactive variables as basic input data. Recent developments in tankhouse design (e.g. permanent cathodes) have greatly increased the design options available for any project, multiplying even further the requirement for calculations. In the past these calculations were tedious and susceptible to human error. A comprehensive computer program can now simplify the task of the process metallurgist, enabling more sophisticated and sensitive plant designs to be produced. The paper describes the successful development of a flexible mass balance program that originallly was used in a feasibility study which had to be completed within a short time schedule. The program has been further developed and used for design and energy calculations; it can be usefully applied to existing plants to assess the impact of variations in operating parameters. The software takes account of staged liberation, electrolyte purification bleed and generates a reliable process inventory listing: it can also cope with stripper starting sheet options and disparate commercial circuits.

Jan 1, 1987