Search Documents

A high strength steel strand bolt has been developed by Barrett, Fuller & Partners as a replacement for conventional rigid bars for primary roof support in coal mines. It is based on a 23mm diameter multiwire steel strand with a tensile strength of 55 to 60 tonnes, The paper summarizes the development of FLEXIBOLT flexible roof bolts, their reinforcement performance and their potential to provide operators, currently reliant on medium to high density roof bolting systems, with a viable, low density roof bolting system offering high roof reinforcement capacity along with the option of installing bolts longer than headroom, in a single pass at the face.

Jan 1, 1993

By Christopher Mark

Preventing pillar line squeezes, massive pillar collapses, and coal pillar bumps is critical to the safe and efficient recovery of coal during retreat mining operations. To help prevent these problems, the U.S. Bureau of Mines has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to, and the load-bearing capacities of, pillars during retreat mining operations. The program can accommodate various retreat mining scenarios including angled crosscuts, varied entry spacings, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder entry designs as well as active workings. A data base of 130 pillar retreat case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1.5.

Jan 1, 1995

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP), Version 1.0, was released at the 19th Gmund Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (I) including uncontrolled convergence into the design requirements for standing roof supports, (21 the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capabilily to define ground reaction curves through convergence measurements alone wthout having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (I) additional graphics capabilities to facilitate rapid assessment of support comparisons. (2) an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and measure of roof coverage for the design layout of the support system These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions whlch could not be fully analyzed in the original version of the program.

Jan 1, 2001

By Xiaolin Wu

Most coal bump occurrences in the U.S. are directly related to mining operations under strong roofs. An understanding of the behavior of bridging or cantilevering strong roofs over working longwall faces is a key to a safe and productive longwall operation. In this paper, an attempt has been made to study the behavior of strong roof beds using the elastic beam theories. Four structural models are formulated to simulate the locations of strong roofs and their distinct weighting stages. For each model, analytical solutions for the deflection, bending moment, stress, and the strain energy stored in both the coal scam and the strong roof are obtained. Solutions for the critical spans, which are controlled by the caveability of the strong roof beds, are developed. The effects of rocks' differing elastic moduli, under tension and compression, on the actual flexural rigidity, and stress redistribution are analyzed.

Jan 1, 1993

By David H. Tang

Similar massive pillar failures were observed in two underground coal mines with different configurations of mine workings and overburden depths. Finite element models were used to analyze the causes and mechanisms of the pillar failure. The results of the analyses confirms the underground observation. For Case No. 1 the failure of coal pillar is mainly caused by a combined effect of smaller coal pillars under a large overburden and the interaction of multiple seam mining. For Case No. 2, the pillar failure was initiated by the weak roof rock but the ultimate pillar failure was caused by the splitting of pillars into very small size.

Jan 1, 1984

By S. Kramadibrata

It has been well accepted that water content significantly changes the physical and mechanical properties of rocks. Experimentation data of Uniaxial Compressive Strength (UCS), Modulus of Elasticity (E) and Brazilian Tensile Strength (UTS) of sandstone showed that increasing water content from oven dried to saturated condition will decrease their values. Ultrasonic tests carried out together with the UCS tests also indicated that the sonic wave traveled faster as rock specimen became saturated. During triaxial tests, the sonic velocity changed with the applied load. It was found that constitutive behavior of dried rock specimen was dependent on the confining pressure, whereas saturated rock specimen did not seem to be dependent on the confining pressure. Dependency of failure criteria such as Mohr-Coulomb. Bieniawski and Hoek & Brown on the water content was conformed as well. In order to show the influence of water content on the stability of an underground opening, a numerical modeling, based on finite element method, was carried out. The model was run using the mentioned failure criteria.

Jan 1, 2000

By W. G. Pariseau

A new approach to the direct inclusion of the effects of joints and geologic structure in rock mechanics analyses is applied to an elastic analysis of stability of a Lucky Friday undercut and 4111 longwall stope (WL) using the finite element method (FW). The approach is base+ on the concept of equivalent properties of a heterogeneous test volume, but does not depend on the assumption that a test volume is a representative volume element. Comparison with conventional FW results show greater variability in fields of stress, strain, displacement, safety factor and energy densities. Stability requires a knowledge of rock mass strengths as well as elastic moduli.

Jan 1, 1989

By David J. Reddish

Longwall systems are inflexible in layout, intolerant of disruption and represent a substantial investment. It is therefore essential drat all understanding of the likely strata behaviour and support requirements is obtained prior to panel development. For many tears rock mechanics engineers have applied numerical modelling based kill finite element techniques to the design of the support and layout of underground excavations. Whilst such design methodology has worked well in civil engineering and hard rock situations, it has been less reliable when applied to excavation design in the soft rocks of the coal measures. This lack of reliability has been identified largely as being the result of the utilisation of unsatisfactory input data, This paper describes the results of an ongoing research programme at the University of Nottingham in which a novel rock mass rating system known as the UK Coal Mine Classification system was developed to enable the prediction of the strata properties that are required as input parameters for use in numerical modelling of the deformation of soft rocks around excavations such as roadways and longwall faces in coal mines. The paper describes the development of the system. the way in which classifications are applied to derive input data for numerical models and gives two case studies ill which deformations and stress re-distributions around coal mine excavations have been simulated by numerical modelling using the FLAC finite difference code.

Jan 1, 2000

By John C. Stankus

In this paper, an innovative concept in longwall tailgate support is discussed. This new concept utilizes a new high capacity roof truss system in lieu of conventional wooden crib block. The first field test was conducted at Bailey Mine and was very successful. Similar tests have been installed in other mines and seams. An extensive instrumentation plan was designed and implemented in the truss test area. The test data has shown that the dynamic roof truss system effectively controls the various abutment pressures caused by longwall mining thus maintaining a stable tailgate entry.

Jan 1, 1994

By H. N. Maleki

The results of five years of geotechnical investigations are presented to develop productive and stable longwall layouts for the Foidel Creek Mine. The program was initiated during the pre-mining stage, and has continuously provided the data required for mine design. From several stress determinations at the mine, the relationship between geologic structure and the stress field/depth was established. The results were used for orienting the entries for improved stability. Cave conditions and load transfer to panel boundaries were evaluated from closely monitored full extraction mining and computer analysis. Back-analyses of ground movements, as compared with the actual measurements, indicated that cave conditions were favorable in spite of the presence of competent, thick-bedded sandstones in the mine roof. Gate pillar design using a yield-rigid concept was developed through computer analyses and underground instrumentation, resulting in 35 and 75 ft wide pillars. The influence of a slickensided bedding plane at the roof contact on pillar yield zones, core confinement, and pillar behavior was evaluated.

Jan 1, 1988

By D. M. Shu

A two-dimensional finite element modelling technique is applied to predict the subsidence movements on a sloping ground surface above a completely mined panel. The modelling is carried out for the surface both directly and using a combination of an equivalent horizontal surface and a rays projection method and the result compared. The rays projection method provides the subsidence components on a sloping surface from the corresponding ones on an assumed equivalent horizontal surface through the point of mean elevation of the relevant part of the sloping surface. This method is used next to compare the subsidences, horizontal displacements and horizontal strains from the mining of a given panel at the surface for different inclinations. The results show that the magnitudes of the subsidence components are greater on the dip side of the slope from the point of the mean elevation, than the corresponding ones on the rise side and the asymmetry increases with the inclination of the surface. The findings are also compared with those of other research workers.

Jan 1, 1992

By Chris Haycocks

The relevant literature concerning ground control, mine planning and reserve conservation in multi- seam mining is reviewed. Factors affecting interaction, interaction mechanisms, and design guidelines are presented in detail. The impact of multi-seam mining on future mining, measures for ameliorating negative interaction effects, and future research needs are also discussed.

Jan 1, 1990

By Edward McHugh

While less than 1% of reported accidents are associated with slope stability problems. slope failures were responsible for about 15% of all U.S. surface mine fatalities between 1995 and 2001. Small rockfalls, which may involve hand-sized rocks weighing only a few kilograms, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic meters of material or more can be fatal even for heavy equipment operators. As part of an ongoing study at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, several remote-sensing technol¬ogies are being evaluated as tools to monitor slopes for hazards and to assess slope stability. Field tests of a hyperspectral imager were conducted to assess its value for improving geologic maps of poten¬tially unstable alteration zones on mine slopes. An interferometric radar device capable of detecting very small displacements on slopes awaits final assembly and field testing. Computerized moni¬toring methods using images from digital and video cameras are being assessed for application to mine slope surveillance. These and other techniques will eventually provide new tools to augment current methods for monitoring ground control hazards in mines.

Jan 1, 2002

By Kevin MacPherson

After 34km of roof bolted drivage the first fall of ground occurred at the Phalen Colliery in the maingate of the 8th East longwall panel. The fall occurred over the stage loader as the wall approached an area of poor roof geology. This area had developed a severe cutter since initial drivage and the longwall had yet to mine through 500m of even worse conditions. This paper describes the cause of the poor roof conditions, the use of polyurethane resin injection and cable bolting to re-stabilize the roof outby the fall, and the measurement of roof movement and performance subsequent to the continuation of mining under the rehabilitated roof.

Jan 1, 1999

By David Bigby

The paper describes research undertaken on an ECSC/K HSE project which investigated several potential physical principles which might be harnessed to provide a non-intrusive means of determining the extent of failure in the near roof of mine roadways and tested the most promising in the laboratory and in the field. It was concluded that the principles which warranted further development were thermal response and laser vibration measurement. In the latter case there is a need to develop an efficient means of imparting energy to the seam to induce sufficient vibration. A new, SIMRAC funded Project will progress work in the field of thermal response.

Jan 1, 2004

By Matthew J. DeMarco

Research personnel at the U.S. Bureau of Mines have conducted longwall gate stability studies at four western U.S. mines attempting to employ yield pillars for improved ground conditions. Located in the Book Cliffs and Wasatch Plateau coalfields of north-central Utah, these operations are generally characterized by multiple-seam mining, cover depths averaging 450 - 600 m (1,500 - 2,000 fl), occasionally extending beyond 760 m (2,500 ft), abrupt cover depth variation due to the overlying canyon/mesa topography, and massive, rigid sandstone roof units. Such conditions encourage severe gate and panel coal bumping, as well as various types of roof instabilities and occasional floor-heave problems. To alleviate these adverse conditions, several mines have employed yield pillars to-reduce hazard-inducing excessive gateroad stress concentrations. This paper describes the evolution of gateroad designs at four of these operations, the specific mining conditions involved, and the general stability performance attained by using yielding gate systems. Mine experiences are "compared" in terms of basic setting conditions, and the general concepts of yielding system applicability and success potential are summarized.

Jan 1, 1993

By Gregory M. Molinda

The U.S. Bureau of Mines has developed a rock mass classification system for coal mine roof control. The Coal Mine Roof Rating System (CMRR) evaluates the structural competence of mine roof using simple field tests and observations obtained from underground exposures in roof falls or overcasts. The basis of the WRR is a weighing system which converts descriptive geologic roof rock data to a numerical value, facilitating its use in engineering design. A full suite of data collection and hand calculation sheets accompanies the CHRR A data base is currently being collected from all major coal basins in the United States to validate the CMW. To date, CHRR values are available from 96 roof exposures in 59 coal mines representing these basins. The system can be used to help solve many practical ground control problems, including longwall gate road design, roof support selection, and decisions regarding extended cut length.

Jan 1, 1993

By G. Skybey

The Directional Drill Monitor (DDM) is an advanced instrument for real time in hole surveying. It was developed by Du Pont (Australia) to suit Australian gassy coal mining conditions. The instrument consists of three units: i. Down hole transmitter ii. Acoustic transducer iii. Data receiver processor unit (i.e. up hole unit). This paper describes the function of each unit in detail and highlights the importance of the DDM in long hole drilling efficiency. Surveying is carried out independent of hole depth. Each survey takes 2-3 minutes to complete, the frequency of surveying to control borehole trajectory is determined by the accuracy required for a particular hole. The DDM is currently being used successfully for long hole drilling in a number of collieries. A high degree of directional control has been achieved. Borehole trajectories were controlled to within +l¬2m of the planned path with intersurvey distances varying between 6 to 18 metres over distances up to 700 metres.

Jan 1, 1992

By Kikuo Matsui

Standing supports such as steel arches or square work supports along with the necessary struts and lagging have been traditionally employed in the longwall gateroads of the Japanese underground coal mines. Miike Colliery has newly introduced the interpanel-pillar mining system and the strata bolting system in gateroads to raise productivity levels and reduce operating costs. The Department of Mining Engineering, Kyushu University, in cooperation with the Miike Colliery and the Coal Mining Research Center, Japan (CMRCJ), has been conducting research into the optimum design of strata bolting as a primary support system in longwall gateroads. This paper presents a brief overview of the current state of strata bolting technique being applied in longwall gateroads at the Miike Colliery and discusses some problems in employing bolting.

Jan 1, 1993

By Ali Benbia

The paper shows results from the physical modelling of longwall excavations concentrating on the fracture pattern development above longwall panels. The modelling technique is briefly described and the detailed analysis of the fracture pattern is discussed. The physical modelling is particularly useful in visualising the caving process above longwall panels. This advantage has been exploited using the image analysis technique. Black and white pictures have been taken while the models are tested in successive stages and then enhanced and stored as binary images by scanning using an image analyser coupled with a video camera. These images are then processed using a custom C program which allows the discretization and characterisation of the fractures. This provides a valuable data base for further numerical and statistical analysis which subsequently may allow the assessment of the water inflow hazard to the workings. In this paper a sequence of different extraction thickness have been analysed using the technique mentioned above to show the effect of the extraction thickness on the fracture distribution and intensity.

Jan 1, 1993