Search Documents

By E. F. Schnitzer, P. J. Wampler

During 1996 and 1997, Oregon experienced flooding on a scale not seen in many years. Some gravel pits located near rivers experienced erosion and, in several cases, breaches between the gravel pit and the river. Initial evaluation of several sites that experienced breaches indicates that impacts to the river system are complex and vary significantly from site to site. The impacts to the adjacent river system may be viewed as both positive and negative. Several floodplain-mining sites in Oregon located in areas of historic river flow have reverted to active riverbed. In many cases, state and federal fisheries biologists and university researchers see the resulting increase in channel complexity and habitat as favorable. The Oregon Department of Geology and Mineral Industries – Mined Land Reclamation Program (DOGAMI-MLR) is performing additional studies of the impacts to the off-channel areas that resulted from the 1996 floods. More data is needed to make sound floodplain decisions regarding mining.

Jan 1, 1999

By Tony Peach

Project Description The Ok Tedi Mine is located approximately 18 km east of the Papua and New Guinea-Indonesia border, on the southernmost extremity of the Star Mountains Range, it is situated almost equidistant from the north and south coastlines. The headwaters of the Fly River system are in the Star Mountains. The open pit mining activities are on Mt Fubilan with a (pre-mining) elevation of 2,095 metres (6,871 Feet) in the Western Province. The mine is in an area characterised by very steep topography and dense tropical rainforest. The pit has been free draining but will cease to be so in the first quarter of 2009. Ok Tedi Mining Limited (OTML) required a drainage tunnel to be driven under the mine, if possible before free drainage was no longer possible. The tunnel was required to be at least 5 m in diameter and 4,200 m (13,776 ft) long, with a possible extension of 1,100 m (3,608 Feet) if the mine decided it was required for additional drainage and underground exploration. The tunnel is being driven up grade at 0.67%, and will be connected to the pit by the raising boring of two 1.1 m (3 Ft. 6 In.) diameter shafts from the tunnel level 250 m (820 Feet) below to the pit. In Tabubil, the adjacent township at an elevation of 640 m (2,100 feet), air temperatures range from a mean at night of 20 (68°F) degrees centigrade to a daytime aver-age of 27 (81°F) degrees. Extremes of 12 and 39 (54°F?102°F) degrees centigrade have been recorded. Rain falls, on average, 339 days each year and totals 8,000 mm (315 inches), and have been known to approach 12,000 mm (472 inches) making the area one of the wettest places on earth. The portal site is at an elevation of 1,200 m or 4,000 ft and the air temperatures are a little cooler and the rainfall a little greater. Access to the mine is by air for personnel and light freight and by ship for heavier goods and materials. The port is at Kiunga on the Fly River 153 km from the portal site. The program for the project was tight, the decision to purchase the required TBM was made in July 2007 and the final decision to go ahead with the construction of the tunnel was made in November 2007.

By Jerry C. Tien

Mining in China dates back at least 4,000 years. Today, with no less than 103,000 metal/nonmetal mines and between 40,000 to 80,000 coal mines, China’s mining industry is undoubtedly the largest in the world. Despite improvements in recent decades, seemingly endless mining accidents continue to make the news. Official coal mining deaths were 6,702 in 2003, and 6,027 miners died in 2004; actual figures may be much higher. Added to these were the 2,699 deaths in the metal and nonmetal industries. Most of these accidents were due to CH4 (methane gas) explosions and fires as a result of inadequate mine ventilation de-sign or practices. A good portion of these accidents occur in small, privately run and often technically illegal mines. During the past 10 years, the Chinese government has attempted to crack down on small and often technically illegal mines without much success. The number of accidents and associated fatalities has not significantly reduced. However, there appears to be a new urgency in China’s efforts to step up mine safety in the country. After its worst reported mine disaster in more than a half century, the government quickly paid reparations to families, suspended high-level officials in charge and announced additonal reforms. One of those was the elevation of the central government’s work safety office to cabinet-level status. There has been increased transparency in reporting and investigation of mine accidents and disasters in recent years. There has also been an increase in public criticism by labor leaders concerning the neglect of mine workersafety.1 This article examines the causes of China’s many mining accidents, current legal and enforcement structures, respective mining health and safety related laws and regulations, recent mining industry developments and the latest effort to curtail small mining operations.

Jan 1, 2005

By John Chadwick

In the drive for faster development advance rates, railbound systems can be advantageous, in the right application. Skanska BS, the contractor to mine-owner VSK Mining, is driving an adit access deep into the Volouské Urchy Mountain in Slovakia to access the Gemerská Poloma talc deposit, some 70 km (43 miles) west of Ko?ice, the economic and cultural center of eastern Slovakia. Skanska began driving the Stolna Elisabeth drift in February 2007, extending 25 kg/m (50 lb/yd) rails (with 750 mm or 30 in. between sleepers) into the mountain to provide the main haulage to bring talc ore and waste out of the new mine once it gets into production. It will also be used for personnel transport, and is now almost complete. As a second egress and for ventilation, a 2.5-m- (8.2-ft-) diameter shaft of about 300-m (984-ft) depth will be sunk from surface down into the orebody. Stolna Elisabeth is a 4.2-km- (2.6-mile-) long drift mined at a cross section of some 11 m2 (118 sq ft). The finished profile is 3.2-m- (10.5-ft-) wide by 3.6-m- (11.8-ft-) high. It has been developed on a very slight incline so that water runs down it to the portal. The portal is 450 m (1,476 ft) above sea level and the end of the tunnel is 475 m (1,558 ft) above sea level. Much of the rock through which it has been developed is magnesite with a compressive strength of 150 MPA. The drilling jumbo is an Atlas Copco twin-boom Boomer 282 Raildrill drilling 42- to 45-mm- (1.6- to 1.7-in.-) diameter holes to a maximum length of 2.5 m (8.2 ft), depending on ground conditions. This is a drill jumbo that Skanska has used successfully on a number of projects during its life. The condition of the rock through which this drift has been driven is extremely variable. Five classifications of A1 and A2 and B1, B2 and [ ] B3, where A1 is the most competent rock and B3 is the worst, have been established. The amount of support used, of which more later is determined by the classification of ground conditions. At the time of the author?s visit, the project it was about 40 days ahead of schedule, thanks to high advance rates. For instance 6 m/day (20 ft/d) was the plan for the advance to be achieved in B1 rock, but sometimes the crews have achieved 8 m/day (26 ft/d) ? which is the average for the whole project ? in those conditions. In A1 the best advance rate achieved is 12 m/day (39 ft/d). The loading unit is a Häggloader 9HR-B on crawler tracks with a pony track to run on the rails. This allows the unit to be towed up and down the drift along the rails. To load from the face, the Häggloader lowers the foot of its onboard conveyor system to the floor and the backhoe pushes material on to it. This digging arm-conveyor combination produces uninterrupted, optimal volume loading of the haulage unit, without spill ? a technique offering load capacities as high as 180 m3/h (6,356 cu ft/hour). Further-more, as an electrically powered machine, it offers great

Jan 1, 2009

By Wayne Green

The Regional Municipality of York, located north of the City of Toronto in Ontario, Canada, has experienced unprecedented growth during the past decade, with new home construction averaging 15,000 units per year. This rate of growth is planned to continue well into the future with a projected growth of more than 500,000 new residents by 2031, combined with a tar-get of more than 300,000 new jobs to provide a sustainable economic base for the region. It should be noted that York region has been designated as one of the key growth centers by the province of Ontario, aimed in part to meet the housing and employment needs of Canada?s growing population. York Region is a mix of urban and rural areas and is one of the most desirable areas to live in Southern Ontario. York region offers an attractive lifestyle, with its nine municipalities and the amenities created by the many rivers, streams and protected greenbelt areas that encompass more than 69 per cent of the region?s area.

Jan 1, 2010

By Steve Skelhorn

Edmonton South LRT is the latest expansion of the Subway system in Edmonton, Alberta, Canada: Consisting of twin 5.8m segmental lined tunnels, 280m long, driven by a Lovat EPB machine. The key challenges were as follows. A 6% downhill grade. Tight radius curves of 250m.Overlying structures within 3m of the tunnel. Strata consisting of sand above the water table, glacial tills and bed rock below the water table. Located within The University of Alberta Campus and adjacent to a hospital. Northern Alberta climate with winter temperatures routinely falling below—minus 30 degrees Celsius. This paper provides a case history and outlines the challenges involved in completing this project.

Jan 1, 2005

By Thomas D. Kelly

In 1900, the average U.S. citizen’s average life span was 47 years. He traveled about 1,900 km (1,200miles) in a lifetime and resided in a home with an ice-box for food storage and oil or gas for lighting. He communicated by mail, telegraph and crude telephones with limited availability and range. By 2000, the average citizen’s life span was 77 years. He traveled an average of 19,000 km/a (12,000 miles/year) by automobile alone. He resided in a home with many electrical appliances, including refrigerators and electric lights. And he communicated almost instantaneously with any other part of the globe by several widely available means, including portable phones and e-mail.

Jan 1, 2002

By C. Laughton

The Deep Underground Science and Engineering Laboratory (DUSEL) is to be constructed at the defunct Homestake Mine, in South Dakota. As a cornerstone of DUSEL?s research program, it is intended to conduct experiments into the fundamental nature of neutrino and proton particles. The experimental apparatus required to con-duct these experiments will be housed in large rock cavern(s) sited at depths of over a kilometer. As conceived, these cavern(s) are planned to have mined volumes of up to half a million cubic meters, and spans of approximately 50 meters. The paper will describe key end-user requirements, and outline the in situ rock conditions and mine site constraints that are likely to play determinant roles in identifying candidate sites and developing cost-effective design options(s).

By C. T. Agouridis

Head-of-hollow fills or valley fills have gained national attention due to increasing environmental concerns, particularly with regards to headwater stream loss. Researchers at the University of Kentucky in conjunction with outside scientists and consultants in the fields of stream restoration, wetland restoration, and mined land reclamation have developed new design methodologies for creating a headwater stream system for a head-of-hollow fill in eastern Kentucky. The design was largely built on the Forestry Reclamation Approach (FRA), which encourages a non-compacted spoil medium to promote tree growth, in an effort to address concerns related to water quantity and quality as well as habitat development. The major components of the design included 1) modifications to the crown geometry, 2) compaction of the crown to control infiltration, 3) utilization of natural channel design techniques, 4) use of the FRA to promote tree growth, 5) creation of ephemeral channels and vernal ponds, and 6) implementation of a novel bioreactor-wetland treatment system to improve water quality.

Jan 1, 2008

By Yuemin Zhao, Daniel Tao, Xinxi Zhang, Qingru Chen, Maoming Fan, Zhenfu Luo, Xiuxiang Tao, Guohua Yang

Coal is currently cleaned with the minimum of size reduction, fine particle processing, recovery, and tailings disposal are major problems. Adequate water resources are not always available. For example, two thirds of China's coal is located in arid areas. Hence, dry separation provides an alternative approach. Of the dry coal separation methods available, air dense-medium fluidized beds have been used to separate 50~6mm coal efficiently. However, excessive bubbling and back mixing of the separated solids in the air-dense media fluidized bed causes the high lower size limit of 6mm for the feed material, this affecting the preparation efficiency. Based on prior study on air-fluidized dense media for 6~50mm coal preparation, this paper presents methods and test results on the fine coal dry classification, static electricity beneficiation of 0~0.5mm coal, and magnetically stabilized fluidized beds for separating 0.5~6mm coal.

Jan 1, 2005

By David Kress

Mill crushing drive systems are essential to cement producers. With the increased emphasis on operating efficiency, it is vital that these systems be dependable and reliable. No one needs the costs or headaches associated with unscheduled downtime or inefficient machinery operation. A reliable drive system starts with the proper selection of the ring, or girth, gear and continues through proper maintenance. Ideally, selecting the right girth gear brings together the gear manufacturer, the system designer and the end user. The gear manufacturer must know the details of the application, the demands that will be placed on the gear and the nature of the equipment to be driven. Similarly, the user and the system designer must be familiar with the variables that affect gear drive performance and service. For example, an application that places a torque load on the drive in excess of its rated capacity will result in gear tooth distress and, in severe cases, breakage.

Jan 1, 2000

By H. Lyn Bourne

This is the fourth annual tabulation that gives mineral royalty information. The table presents previous information plus about two dozen new entries. In addition to the royalty information, some entries show the cost of purchased reserves. Last year's tabulation appeared in two issues, to accommodate all of the information. This year the format has been changed slightly so the table can be printed in one issue. This year's table presents the commodities in the same sequence as last year. Sand and gravel information appears first, followed by: crushed stone for aggregate; other stone; industrial sand; other industrial minerals; energy minerals (coal, oil shale, uranium); and finally metals. As always, a caveat relates to factors that influence the reserve values. The data should serve only as a general reference. The table is not intended to present an absolute scale of reserve costs. Several factors influence the value of mineral commodities. These factors include: • location and transportation costs (especially significant for most industrial minerals); • market conditions for both the commodity and the company acquiring the right to mine it; • quality or grade of the deposit as it reflects the amount of processing and beneficiation necessary to produce the finished product; • and legislative restrictions and conditions for mining a given material at a given site. These and other factors will influence reserve costs of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity; the location (either by state, US geographic area, or Canadian province); the cost (R for royalty and P for purchased cost); and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cuft), tons (/T) (2000 lbs) or acres (/A). 1 cu yd = 0.76m3 1 cu ft =0.28m3 1st = 0.9 t7 1 acre = 0.40 ha or m2 In several cases the royalty is a percentage of the finished products, sale price and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: J. Dunn, T. Eyde, K. Loda, L. Morgan, F. Nix, H. Sorenson, and L. Williams. Several people have said they would like this to be an annual tabulation. That can happen if new information comes to the writer. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write or call: H. L. Bourne, c/o Neyer, Tiseo & Hindo, Ltd., 38955 Hills Tech Dr., Farmington Hills, MI 48018, (313) 553-6300. Only with new information can this become an annual and current source of reserves costs.

Jan 8, 1986

By James D. Nickerson

Thee Brightwater water treatment facilities, currently scheduled to be completed in 2010 and begin operating in 2011, will serve the northern part of King County, WA. The facility includes a new treatment plant and extensive conveyance system consisting of more than 21 km (13 miles) of influent and effluent conveyance tunnels and five portals. The majority of the conveyance system tunnels are mined by tunnel boring machines (TBM) and microtunnel boring machines (MTBM). Tunnel and portal construction is divided into three main contracts. The Ballinger Way receiving portal, constructed under the central tunnel contract, is the terminus for the BT-3 leg of the central contract and the BT-4 terminus of the west contract. The shaft has a 7.3-m (24-ft) finished inside diameter (ID) to accommodate removal of the central project TBM and the west contract TBM and extends to a depth of 66 m (216 ft) below grade through a complex and challenging soil profile characterized by multiple ground water tables. Vinci Grand Projects/Parsons/Frontier-Kemper Constructors (VCFK) was the joint venture team for the Ballinger Way portal. Frontier-Kemper was responsible for the shaft sinking. VCFK evaluated either slurry wall techniques or ground freezing for earth support during excavation of the portal and liner installation. The selection process took into account the vertical depth, cost, past practice, geology, water tables and a 9-m- (30-ft-) thick zone of contaminated soil at the top of the shaft. Ground freezing, which would also act as a hydraulic barrier, was deemed the better option for this project. The contract was awarded to New Jersey-based geotechnical contractor Moretrench. Typically, frozen walls, by design, key into an underlying cutoff. At the Ballinger Way portal, however, the [ ] freeze bottomed out in a substantially thick stratum consisting of predominantly clay, but with some inclusions of permeable soil that indicated significant ground water pressures. To ensure stable conditions at the bottom of the shaft, Moretrench, which also specializes in dewatering, designed and installed a perimeter array of deep wells to temporarily depressurize the permeable soils. The movement of ground water generated by pressure

Jan 1, 2009

By T. A. Rundle, K. Kim, W. M. McCabe, E. C. Gregory

Overcoring tests were conducted at the Near-Surface Test Facility(NSTF) to assess the suitability of five techniques (U.S. Bureau of Mines borehole deformation gauge (BDG), Commonwealth Scientific and Industrial Research Organization (CSIRO) hollow inclusion stress cell, Luleå triaxial gauge (LuH gauge), and Council for Scientific and Industrial Research (CSIR) doorstopper) for in situ stress determination in a closely jointed basalt. This effort is in support of the Basalt Waste Isolation Project, which is studying the feasibility of locating a nuclear waste repository in the basalts of the Hanford Site in southeastern Washington. This paper presents the results from the overcoring study that formed the basis for selection of two techniques to be used during the further exploration of the basalt formations at depth.

Jan 1, 1983

By Graham W. Gibbs

The current state of knowledge concerning mesothelioma risk estimates is reviewed. Estimates of the risk of mesothelioma exist for the commercial asbestos fiber types chrysotile, amosite and crocidolite. Data also exist on which to assess risks for winchite (sodic tremolite) and anthophyllite asbestos. Uncertainty in estimates is primarily related to limitations in measurements of exposure. Differences in the dimensions of the various fiber types and of the same fiber types at different stages of processing add a further complication. Nevertheless, in practical terms, crocidolite presents the highest asbestos related mesothelioma risk. The risk associated with sodic tremolite (winchite) appears to be similar. In chrysotile miners and millers, the mesothelioma risk has been linked with exposure to asbestiform tremolite. Exposure to chrysotile in a pure form seems likely to present a very low if any risk of mesothelioma. While the majority of mesothelial tumors result from exposure to the asbestos minerals, there are other well established and suspected etiological agents. While a practical threshold seems to exist for exposure to chrysotile, it is unlikely to exist for the amphibole asbestos minerals, especially for crocidolite. To date there is no indication of an increased risk of mesothelioma resulting from non-commercial fiber exposure in the taconite industry. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Amosite; Grunerite; Taconite; Crocidolite; Tremolite; Anthophyllite; Winchite; Risk estimation; Etiology

Jan 1, 2007

China has made great progress in thick coal seam mining, commonly characterized by longwall top-coal caving mining and single-pass longwall mining with a large cutting height. At present, the maximum mining thickness of longwall top-coal caving reaches 20 m while that of single-pass longwall mining approaches 8.8 m. The top-coal caving–related technologies have significantly improved the mining efficiency of thick coal seams and have also made a great contribution to the centralized underground mining of coal. Thus, the number of underground coal mines is greatly reduced in China. However, due to the increase of the mining height and the changes in mining operations, the overburden movement caused by the mining of thick coal seams is more intense, and the influence scope is larger, which brings a series of new problems on ground control of longwall faces. In order to enhance ground control and improve the mining efficiency of thick coal seams

Jul 28, 2020

By Steve Kral

Most innovations in the mining and processing industries have come from the need to produce more for less. Extracting minerals from the ground is expensive. And it is a constant struggle for mine operators to maintain the line between profitability and loss. The same holds for equipment suppliers. To maintain competitiveness, mining equipment manufacturers are building their machines with an eye to what the customer needs. Equipment makers know that if they do not supply machines that are productive and cost efficient, their competitors will. The result has been that the mining industry can now produce more ore with fewer people and more productive equipment. But, for all of the advances made in equipment, mine operators still demand machines that produce even more, are safer for workers and the environment, require less maintenance and can do the job at lower costs. And equipment manufacturers keep responding with larger, smarter and more technologically advanced machines.

Jan 1, 2005

Pillars in underground limestone mines are required to support the overburden and provide a safe, stable working environment for mining personnel and equipment. Pillar stability was assessed by the National Institute for Occupational Safety and Health in underground limestone mines in the Eastern and Midwestern United States. It was found that current mine layouts have been successful in providing support to the overburden, while a small number of isolated pillar failures were observed. The stable pillar layouts and failed pillars were plotted on a chart that demonstrates the relationship between pillar width-to-height ratio and pillar stress. The results show that pillar failures occurred at the lower range of width-to-height ratios and can occur at relatively low stress levels. Zones indicating the potential risk of pillar instability are shown on the chart, based on hazards associated with the onset of rib spalling, large angular discontinuities and unconfined pillars. The chart can assist limestone mine planners to evaluate potential instability in current or new pillar layouts that are similar to those included on the stability chart.

Jan 1, 2008

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By D. R. Wilburn

This summary of international mineral exploration activities for 2008 draws upon available information from industry sources, published literature and U.S. Geological Survey (USGS) specialists. The summary provides data on exploration budgets by region and mineral commodity, identifies significant mineral discoveries and areas of mineral exploration, discusses government programs affecting the mineral exploration industry, and presents analyses of exploration activities by the mineral industry based upon these data. Two types of information are reported and analyzed in this annual review of international exploration for 2008: 1) budgetary statistics expressed in U.S. nominal dollars provided by Metals Economics Group (MEG) of Halifax, Nova Scotia (Metals Economics Group, 2008a, b), and 2) information on regional and site-specific exploration activities that took place in 2008 and compiled by the USGS. The MEG information summarizes planned company budgets for worldwide exploration activities in 2008, primarily for precious metals (gold, platinum-group metals and silver) and base metals (copper, lead, nickel and zinc). MEG includes information on additional mineral commodities only where it is available. Information on uranium exploration was included in the MEG overview for the first time in 2007, although this information was not included in the USGS analysis. The MEG survey methodology was changed in 1999 to include companies with exploration budgets between $100,000 and $2.9 million, as well as those companies included in prior studies whose anticipated budgets were above $2.9 million. MEG estimates that its post-1999 surveys cover at least 90 percent of world nonferrous nonfuel mineral exploration budgets. The 2008 survey is reported by MEG to cover an estimated 95 percent. Companies that chose not to participate in the MEG study, private companies that do not publish data, and government-funded exploration activities make up the majority of the remaining 5 percent. MEG included 91 more companies in its 2008 survey than it did in 2007 USGS compilations of site data described here primarily include nonfuel minerals, with an emphasis on base metals, diamond and precious metals. Analyses are based on information provided by USGS mineral commodity and country specialists and by other USGS scientists, as well as industry contacts and trade journals.

Jan 1, 2009