Search Documents

By S. Iverson

Fall of ground accidents continue to be a source of injury in underground metal mines. MSHA accident statistics indicate that most rock fall accidents occur at a new face where drilling and blasting methods are used. Removing loose rock by scaling is imperative to removing the potential for rock fall injury. Detection of potentially loose rock could improve the scaling process and result in fewer rock falls. Infrared thermal imaging cameras were investigated as far back as 1966 as a tool for loose rock detection. Early on it was clear that sensitivity (e.g. detectable temperature increment) is a key factor in this application. Both pixel resolution and temperature resolution have greatly improved with modern instruments. This paper describes an evaluation of modern infrared thermal imaging camera technology to detect loose rock conditions at six underground metal mines in the western U.S. It was found that thermal images provide a high resolution visual discrimination between loose rock and intact rock. However, detecting loose rock was difficult in cases where the rock and ventilation air were at the same temperature. Loose rock was detected when rock was both warmer and cooler than the ventilation air temperature. Warm rock with cool ventilation air provided the best conditions for detection.

Feb 23, 2014

By T. G. Legare

It is now well documented that trace amounts of silver, gold, and platinum group metals occur in certain geothermal brine deposits. A significant body of literature has been generated over the last twenty years which describes attempts to quantify the frequency and levels of these precious metals in the brines. This literature is often confusing and contradictory. For example Barnea 1 states that the Salton Sea geothermal field carries 2 ppm gold, yet more recent data by workers at Lawrence Livermore National Laboratory2 (LLNL) concludes that the gold level in Salton Sea brine is <0.07 ppb. They report a platinum level in one well of 55 ppb. This apparent contradiction may be explained by sampling source and technique, but is most probably explained by difference in analytical technique. Analytical techniques and problems will be discussed in the next section.

Jan 1, 1985

By I. Ward, E. Milosavljevic, M. Botz

"The silver nitrate titration method is a rapid and acceptably accurate means of analyzing for cyanide in leach solutions that contain primarily free cyanide. However, in leach solutions containing elevated levels of copper, the titrimetric method overestimates the concentration of free cyanide and underestimates the concentration of weak and dissociable (WAD) cyanide. The authors have developed a modified potentiometric (MP) titration method for determining WAD cyanide that overcomes issues associated with high copper levels in solution. The new MP-WAD method involves addition of a chemical ligand to the sample prior to silver nitrate titration to release cyanide bound to copper. Once released from copper, cyanide in solution is no longer affected by the presence of copper, and titration results are quantitative rather than empirical. In multiple laboratory trials with synthetic solutions and complex actual leach solutions, analytical results obtained with the new MP-WAD method were found to be within about ±5% of analyses obtained with the USEPA OIA-1677 WAD cyanide analytical method.IntroductionThe silver nitrate titration method is widely used to estimate the concentration of cyanide in leach solution for purposes of cyanidation process control. Cyanide determined by silver nitrate titration is commonly referred to as “free” cyanide, but frequently should be referred to as “titratable” cyanide. By definition, free cyanide is the sum of the concentrations of aqueous hydrogen cyanide HCN(aq) and the cyanide anion CN- (ASTM, 2010). Titration will only yield a reasonably accurate measurement of free cyanide when metal-cyanide complex concentrations (e.g., cadmium, copper, mercury, nickel, silver and zinc) in solution are low. In other words, titration will only yield a reasonably accurate measurement of free cyanide if the solution primarily contains free cyanide."

Jan 1, 2015

By Qingming Feng, Jinhong Zhang

A study has been carried out to apply fly ash as a high strength, water-resistant precast construction material through geopolymerization. Experiment results show that the working conditions such as water content, the concentration of NaOH, curing temperature, and curing time significantly affect the mechanical property of geopolymermatrix. Through optimization, an above-100MPa compressive strength has been achieved with the geopolymerization products. The optimum working conditions involves 10MNaOH concentration, 14–15% water content, and curing at 90 °C in an oven for 1 day or at ambient condition for 3 weeks. Adding Ca(OH)2 does not help to increase the compressive strength of the specimen.Water soaking tests show that the geopolymerization product has a very high water resistance without losing noticeable compressive strength, even after a 1-month soaking time. To elucidate the geopolymerization mechanism, microscopic techniques such as SEM/EDS (scanning electron microscopy and energy-dispersive X-ray spectroscopy), XRD (X-ray diffraction) and ATR-FTIR (attenuated total reflectance Fourier transform infrared) are also applied to investigate the microstructure, the elemental and phase composition of geopolymerization products. The findings of the present work provide a novel method for applying fly ash as a high-strength water-resistant precast construction material.

Aug 17, 2020

By R. P. Schneider

The Chino mine, concentrator, and smelter are located in Grant County in Southwestern New Mexico. Chino Mines Company is a partnership two-thirds owned and operated by Kennecott Santa Fe Corp., and one-third owned by MC Minerals Corp. (Mitsubishi) of Japan. The Chino Ore Body The Chino ore body is a widely varied deposit of rock types and contains intrusive stocks and sediments. The stocks contain chalcocite in a matrix of quartz, mica, and feldspar. Much of the feldspar is altered to clay. Some of these stocks are enriched with native copper. The sediments contain chalcopyrite associated with gangue minerals including magnetite, pyrite, garnet chlorite, and epidote. The contact of the stock and sediment is heavily altered to chlorite and clay. The stock ores contain economic quantities of molybdenite. The operating work index of Chino ore varies from 5 to 20 kwh/ton and averages 8.5 kwh/ton. The ore head to the concentrator averaged 0.81% copper and 0.010% molybdenum. Fifteen percent of the total copper head exists as nonsulfide mineralization.

Jan 1, 1985

By Daniel Threlfall

The disposal of hazardous chemical wastes will be one of the major environmental issues of the 1980&apos;s. Approximately 50 million tons of hazardous wastes are produced yearly. One of the major aspects of the problem is the siting, design and construction of environmentally acceptable disposal facilities to accommodate this huge volume of material. Surface mines have been considered attractive for development as disposal sires for several reasons: 1. Surface mines represent an open pit that can conveniently serve as a repository for wastes. This could represent a significant economic savings when compared with sites on undisturbed lands chat might require extensive excavation or embankment construction.

Jan 1, 1981

By H. Lyn Bourne

This marks the 15th consecutive year for this column. During 1995, readers were asked to supply royalty data for construction raw materials especially for states where none is available. The response was discouraging and royalty data are still missing for several states for either sand and gravel or crushed stone. Several readers have said that this article has merit but more new information is needed to justify its continuation. Several articles and pieces of news relative to mineral royalties appeared in the trade journals. R. Lee Aston (E&MJ, November, 1995, p. 16N) described South Australian royalties as amended by the government in1994. The royalty rate (a percentage) was lowered but the assessed value for minerals was raised and the current rate amounts to 20 cents//t (18 cents/st).

Jan 1, 1996

By S. Todd Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty in factor of safety predictions for soil slopes where there is incomplete knowledge of the spatial distribution of soil properties. A case study considers a natural clay slope in Canada. The sequential indicator simulation technique is used as a means for generating a series of spatial maps of soil properties for this site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. Factor of safety determinations are then made for each simulated map using the simplified-Janbu approach, where the computations are performed with a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the distribution of factor of safety conditional to the type, position, and value of existing site characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1993

By Feng Liu

"With seven new applications for plans of work for exploration in the international Seabed Area approved by the Council during its twentieth session of the International Seabed Authority, 26 total approvals have been made by the Council up to date. Among them, three contracts were made with COMRA. On 8 August 2014, China Minmetals Corporation submitted another application to the Authority for approval of a plan of work for exploration for polymetallic nodules in the Area, which is also sponsored by the Government of the People’s Republic of China.China is one of the main contributors to the international seabed regime. The Presentation will describe China’s activities in the Area, such as exploration, technology development, environmental protection and policy making.JIAOLONG is a submersible with capacity of 7000 meters. JIAOLONG’s sea trials were carefully made in 4 years, from 2009 through 2012 and it successfully dove to a depth of 7062m in June 2012 at Mariana trench. A so called "Test Application Phase" started thereafter, and is planned to last for 3-4 years. Two cruises and 4 legs have already been made since then. A wide-range of findings were obtained during dives in South China Sea, and in COMRA’s Exploration Contract Areas for polymetallic nodules and cobalt-rich ferromanganese crusts. This presentation will reveal the colorful findings."

Sep 1, 2014

By A. M. Marabini

Flotation of rutile with N-benzoyl-N-phenyl-hydroxylamine (N-BPHA) has been investigated. Initially, floatability tests were performed in a Hallimond tube. The results indicated that rutile was floatable in the pH range from 2 to 4 at N-BPHA concentration between 2x10-3 M and 2x10-2 M. Selectivity against hematite was recognized when operating at pH values below 2. Following the hypothesis of the formation of a surface chelate between N-BPHA and titanium ion, this compound was precipitated from a solution of Ti(SO4) to which N-BPHA was added. I.R. spectrometry oft the rutile before and after treatment with N-BPHA solution confirmed the presence on the rutile surface of the same compound. The absorption isotherm and kinetics were determined by analyzing N-BPHA in solution with an U.V. technique. A hypothesis for the mechanism of adsorption of N-BPHA on rutile is suggested.

Jan 1, 1982

By S. McAlister

This paper outlines the development of the Falcon enhanced gravity separator. Design objectives included continuous operation with sharp separations, mechanical simplicity, minimization of process water demand, the ability to apply a centrifugal field up to 300G&apos;s, unit capacity in excess of 100 t/h within a footprint of 10 square meters, a capital cost below $US 4,000 per t/h capacity, and total operating costs of less than $US 0.40 per tonne. A parallel development has been inexpensive, effective, semi-continuous equipment for recovery of precious metals in the free metallic state. These objectives have been largely met. There are significant opportunities for the technology in many mineral processing applications.

Jan 1, 1998

By L. F. Zeiler

In the past, health concerns in coal mines have primarily centered on those elements which have been essentially inherent to the mining environment. These would include respirable coal mine dust, respirable crystalline silica, excessive noise levels, and diesel exhaust particulates. Commercially-available chemical products are prevalent on mine property. These potentially toxic materials are chemical formulations that can degrease, clean, and lubricate metal parts, separate coal from rock in float/sink operations, and aid in roof consolidation, among other uses. As the general public has become more aware of the hazards of chemical exposures, miners have likewise become more concerned about working with an ever-expanding variety of chemical products on the job. Often, product or chemical specific hazard communication training is inadequate or ineffective, and miners do not know exactly what the ingredients are in the products they handle, or the health hazards involved with their use or misuse. Currently, the Mine Safety and Health Administration (MSHA), by law, enforces 1972 Threshold Limit Values (TLV). MSHA is making preparations to adopt new personal exposure limits for enforcement. The values given throughout the article are 1994 TLV&apos;s and are not enforcement standards, but are used for discussion purposes. They reflect the current scientific thinking regarding personal exposure to these chemical agents. An overview of these products is presented, and the potential health hazards associated with their use are discussed. Controls needed to prevent overexposures, such as proper handling procedures and personal protective equipment, are covered. Methods used to collect and identify contaminants are presented.

Jan 1, 1995

By J. F. T. Agapito, L. J. Gilbride

High horizontal stresses were recognized to impact roof stability more than 60 years ago. Since then, numerous measurements associated high horizontal stresses with difficult ground conditions. This paper presents case histories illustrating the practical usage of roof stress determinations for helping assess stability, not only in the case of high horizontal stresses but also of low stresses. Examples are given of high stresses associated with faults, mine design changes, quantification of stress shadow effect, and anistrophy. The paper concludes with a comparative evaluation on the effect of various stress fields on ground support requirements.

Jan 1, 2002

By James W. Estep

The sulphur shortage that has occurred in the past two years has directed attention more and more toward sour natural gas reserves, Wellhead values of sour gas vary widely depending upon the acid gas composition, location, market conditions, and necessary processing charges. Preparation of a saleable residue gas is considerably more involved and expensive than that normally encountered in treating a sweet gas. Recent revisions in sales gas specifications have increased capital costs and processing charges. The presence of hydrogen sulphide and carbon dioxide in a natural gas contributes to shrinkage factors that may approach 50%. Fuel required by the gas sweetening process and sulphur slant tail gas incineration also contributes to a further reduction in the volume of residue gas available for sale. The additional processing facilities involving gas sweetening, mercaptan removal, expanded utilities, sulphur recovery and sulphur handling, all demand additional operating and maintenance staff. A favorable sulphur market under certain conditions may justify the processing of sour gas whereby sulphur is either a by-product or a co-product, Five typical cases involving different compositions of sour gas are presented for evaluation. Capital costs, operating problems, and operating costs are presented in detail for full economic evaluation

Jan 1, 1967

By D. A. Karvonen

Although the economy in the Province of Saskatchewan has historically been agriculturally oriented, a major new source of wealth has been realized through natural resources such as petroleum and natural gas, coal and uranium and since the 1960&apos;s - potash. Potash or potassium chloride, in the form in which it is presently produced in Saskatchewan is used primarily as fertilizer, a source of potassium, one of three essential elements required for healthy plant growth with about 5 percent of production sold to the chemical industry for use in such products as soap and liquid detergent, glass and ceramics, textiles and some pharmaceuticals. Saskatchewan is estimated to have approximately 40 percent of known world potash reserves and its ten active mines account for some 25% of annual world production. The development of this resource was recognized to be important to the development of Saskathcewan. In an effort to guarantee a fair and lasting economic benefit to the Province of Saskatchewan the Potash Corporation of Saskatchewan (PCS) was created on February 4, 1975 through an Order-in-Council under the Crown Corporation&apos;s Act and later on April 1, 1976, the Potash Corporation Act provided for its continuation. PCS was given the mandate to acquire ownership of a significant portion of the potash mining capacity in Saskatchewan and to establish an organization capable of operating the facilities, marketing the product and conducting all of the other activities necessary for a successful corporation competing in the world potash industry.

Jan 1, 1983

By M. Z. Rashad

The purpose of this paper was to compare the covariance and multiquadric functions in same mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 by 16 kilometer square area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of forty-eight test stations were computed by using the data of sixty-three control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function more simple in computation than the other one, which needs to precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometrical and physical considerations rather than covariance functions.

Jan 1, 1990

By C. L. Schneider

The problem of predicting the liberation spectra produced by a closed continuous grinding circuit is of fundamental importance for the design, optimization and control of most operations in an ore dressing plant. The only known approach through which such a calculation can be performed is the population balance model equation. The latest and certainly most significant progress made in this area is the solution proposed by King (1990), which requires one textural parameter that can be measured directly from the ore being studied. The main advantage of King&apos;s solution is that it does not require the estimation of hundreds of arbitrary parameters that cannot be independently measured, as required by the existing conventional solutions. However, King&apos;s solution relies heavily on a knowledge of the detailed internal structure of the Andrews-Milm diagram (Andrews and Mika, 1975). This has never been measured for any ore. The characterization of the internal structure of the Andrews-Mika diagram requires the measurement of the liberation spectra at several progeny sizes produced by the breakage of monosize, monograde particles at several different grades. In this paper, a procedure based on magnetic fluid fractionation for generating seven narrow-size, narrow-grade samples is presented. Each of these samples was then broken into six progeny size classes in an ultrasonic mill. The one-dimensional liberation spectra of each of the 42 progeny and seven parent particle samples were then measured by image analysis. The measured linear-grade distributions are presented in this paper. The calculation of the correspondent volumetric-grade distributions is discussed.

Jan 1, 1994

By Kevin A. Foo, Murray D. Bath, John H. Canterford, Arnaldo Ismay

There is no doubt that the dominant future source of gold will be the so-called refractory ores, especially those with gold in a pyrite/arsenopyrite matrix. Minproc Engineers is taking an active role in establishing detailed design criteria for a number of apparently competing processes. This involves generating a detailed understanding of the metallurgy involved, systematic pilot plant testing, and the application of advanced engineering technologies. This presentation outlines the approach adopted by Minproc as well as the design criteria for several current projects.

Jan 1, 1989

By K. P. Stricker, H. Keddeinis, K. Grebe

Recent investigations by Mannesmann Research have shown that disintegration of sinter with widely varying quality levels is subject to a much more complex set of influences than was previously assumed. It was confirmed that disintegration at temperatures between 300° and 600°C (570° and 1,110°F) is triggered by the degradation of hematite. The specific tendency of hematite to disintegrate is, however, not constant: sinters containing the same amount of hematite can show widely differing disintegration tendencies, depending on structural homogeneity, porosity, and gangue quantity. Sinters with heterogeneous structures transmit stress to the hematite phase and this favors disintegration. Another factor is the brittleness of the glassy silicate phase, which can be influenced even by small modifications of minor gangue constituents.

Jan 2, 1984

By C. J. Roos

Ground-engaging tools are used to prevent damage to the main components of earth-moving equipment. These tools consist of everything from shovel teeth to replaceable drill bits to dozer wear plates. The costs of these "consumable" items are increasing with the costs of raw materials. This project developed a tool to be used by Newmont Mining Corp. to predict the consumption of excavator teeth at a particular mine site. This paper presents the results of the Montana Tech research project in which an equation was developed to predict excavator teeth consumption based on production rates and rock properties.

Jan 1, 2010