Search Documents

By Jean Habimana

The Detroit Upper Rouge Tunnel CSO Control Project will capture and store up to 201 MG of combined sewer overflow from 28 outfalls in Detroit, Dearborn Heights and Redford Township during wet-weather events. The history of rock tunneling in the area is associated with high groundwater inflows, artesian pressure, and hazardous and combustible gases. This paper presents the geotechnical considerations for designing the 11.28-km (7-mile) long, 9.14 m (30-ft) finished diameter tunnel and its associated adits, chambers and shafts, including the discussions of geotechnical investigations, rock mass characterization, estimated groundwater infiltration during construction, and the selections of excavation methods and lining system based on anticipated ground behavior to be encountered.

Jan 1, 2008

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By R. M. Imhof, M. J. G. Battersby, G. Ciernioch

Pneumatic flotation is rapidly becoming accepted in the main stream of flotation techniques. Imhoflot is a pneumatic flotation process that in recent years has undergone progressive development. It combines short flotation times with excellent selectivity by employing intense pre-aeration and dispersion. K+S GmbH (K+S), Germany, has installed a complete Imhoflot flotation plant at its Sigmundshall plant. The plant treats hard salt consisting of sylvine, halite, anhydrite and kieserite. The reason for selection was that Imhoflot achieves the required grades of plus 60 weight percent K2O whilst offering lower operating costs than conventional flotation installations.

Jan 1, 2002

By J. Geisler

When addressing Germany’s resource supplies, we need to distinguish between those domestically available and imported ones. Resource extraction ostensibly competes with the designation of protection areas. However, the parallel existence of wildlife and plant life, and operations in the areas used for resource extractions is continually underestimated. The European Commission has compiled guidance documents facilitating the extraction of resources from protected areas. With regard to resource productivity, the market appears to be the appropriate instrument for minimising resource consumption. Policy makers are now called upon to create a legal framework leading to a consensus accepted by society.

Jan 1, 2011

By Patrick Scott, Germán Schmeda, Morgan Mullins, Liam Knudsen, Bradley S. Van Gosen, Carma A. San Juan, Nicholas A. Karl, Jeffrey L. Mauk, Clayton Forbush

The objective of the US Geological Survey’s mineral deposit database project (USMIN) is to develop a comprehensive twentyfirst century geospatial database that is the authoritative source of the most important mines, mineral deposits, and mineral districts of the US. Since May 2017, the project has focused on critical minerals. Data for critical minerals that are produced as products are relatively robust, whereas data for critical minerals that may be recovered as byproducts are commonly of much poorer quality. Similarly, more is known about critical minerals that occur in conventional deposits than where those critical minerals occur in unconventional deposits. For example, rare earth elements occur principally in deposits hosted by alkaline igneous rocks, but there is potential for their production from phosphate rock mining, which is less documented. Lithium (Li) has been recovered from pegmatites and brines, but other Li-bearing deposit types have been delineated that may go into production. Cobalt may be produced as a byproduct or coproduct from a wide range ofmineral deposit types, whereas rheniumis a byproduct of copper ore. Significant opportunities for research exist that could help identify new sources of critical minerals, and may also help increase production and recovery from existing sources.

Feb 8, 2021

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By A. Opara

The weathering of coal mine waste rock releases iron, calcium, sulfate and associated trace elements like selenium [Se], which are introduced to seepage waters. Nitrogen species, such as nitrate and ammonia, are also found in association with coal-mining drainages mainly due to leaching of residual blasting compounds. Elevated concentrations of Se are a ubiquitous occurrence in coal mining environments in British Columbia, with values ranging from below 50 to over 500 µg/L in site waters. Selenate is the most common form of selenium found in waste rock seepages, and is exceedingly mobile in aerobic freshwaters. A major concern with waterborne Se in British Columbia is the potential for its bioaccumulation in aquatic food chains. Treatment to remove Se from coal-mining wastewaters has proven to be challenging for conventional water treatment technologies. Compounding this challenge, many streams are characterized by high flows and low selenium concentrations. Conventional membrane and ion exchange treatments produce concentrated brine streams that are difficult to treat or require disposal. Conventional biotreatment systems use excess nutrients to provide the required electrons to compensate for inefficient and variable electron availability, as well as to adjust reactor chemistry. The Electro-Biochemical Reactor (EBR) technology provides electrons to the microbes directly at a low voltage potential (1-3 V), supplying a controllable and consistent supply of useable electrons to the system and microbes at low current. In this manner, the EBR technology overcomes the shortcomings found in conventional systems, as it reduces the required nutrient addition and provides a more controllable, efficient, economical, and robust biotreatment system than found in past generations of biological treatment systems. Additionally, the EBR process does not produce excess solids or biomass; therefore, solids management post-treatment is not required. Laboratory EBR bench-scale and on-site pilot-scale systems were used to treat five British Columbia coal mine wastewaters; influent Se concentrations ranged from 35 µg/L to 531 µg/L. Se treatment targets for the tested waters ranged from 5 to 10 µg/L. Mean Se concentrations in EBR effluents ranged from 0.5 µg/L to 1.4 µg/L, while reducing sulfate concentrations. The test data demonstrate that the EBR technology is an effective Se removal option for British Columbia?s coal-mining wastewaters.

Feb 23, 2014

By J. A. Rusnak, M. M. Gadde, S. S. Peng

In situ stresses are one of the key inputs to a successful underground excavation design. Because of the complex mechanisms involved in arriving at the current state of stress at a point in the Earth’s crust, often the only reliable way of estimating in situ stresses is by actual measurement. In the United States coal mines, overcoring relief method is by far the most popular technique used for estimating the virgin stress field. Typically, for stress measurement with overcoring, a vertical borehole is drilled into the roof or floor of an underground coal mine opening to a certain distance and change in borehole diameter is monitored at multiple points along the length of the hole when this borehole is overcored. For the measured stresses to represent the pre-mining stress field, the measurement points should be located beyond the influence zone of the mine opening. Actual data from several US coal mines have been collected to check if the measured stresses by overcoring represent true in situ stresses. The data indicate that most of the stress measurements were within the excavation influence zone. A three-dimensional numerical modeling methodology was applied to one of the collected cases to correct the measured stresses for the excavation influence. The modeling approach demonstrated the usefulness of integrating numerical modeling into a stress measurement program to estimate ‘true’ in situ stresses.

Jan 1, 2006

By W. Scheetz

The Brewer Gold Mine is an open-pit, heap leach operation that processes about 122 kt/m (135,000 stpm). The mine is operated by Brewer Gold Inc., a subsidiary of Westmont Mining Inc., and is located near Jefferson, SC, about 80 km (50 miles) southeast of Charlotte, NC and 80 km (50 miles) northeast of Columbia, SC (Fig. 1). All of the ore to date has been produced from a breccia body of hydrothermal origin and a related smaller body of fault-controlled ore, known as the B-6. Reserves at the time the mine commenced production were 4.6 Mt (5.1 million st) grading 1.4 g/t (0.042 oz per st) gold. History Although some reports of a pre-Revolution War shaft at the Brewer are in the literature (Lieber, 1856, Nitze and Wilkens, 1897), gold was first produced in earnest from the Brewer Mine in 1828. Production occurred primarily from placer deposits south of the present mine workings. Lieber noted in 1856 that “every branch, gulch, ravine or even declivity of the main hill has been washed and rewashed.”

Jan 1, 1991

By F. M. Doyle

Ion flotation shows great promise for recovering and removing metal ions from dilute process streams, either for environmental compliance or to recover values. This technique uses an ionic collector to concentrate non-surface active colligend ions of the opposite charge from a bulk solution at the solution?vapor interface. With a sufficiently large solution?vapor interfacial area (provided, for example, by sparging gas through the solution), the colligend can be concentrated and removed along with the collector in a foam phase. A key limitation on using the technique in the minerals industry, where many process streams contain a variety of ions and have relatively high ionic strengths, is the need to control which ions are interacting with the collector. Here the effect of three different chelating agents, namely dodecyldiethylenetriamine (Ddien), ethylene diamine tetraacetic acid (EDTA) and triethylenetetraamine (Trien), on the selectivity of copper, nickel and cobalt, or copper and alkaline earth metal ions, is reported. The results are discussed in terms of their implications for adoption in the minerals industry.

Jan 1, 2009

By R. L. Virta

Four companies mined ball clay in four States during2004. They were H.C. Spinks Clay (owned by Franklin Minerals) Kentucky-Tennessee Clay (owned by Imerys),Old Hickory Clay and Unimin. Production was estimated to be 1.46 Mt (1.61 million st) valued at about $56.9 million, based on a preliminary survey of the ball clay industry. In 2003, production was 1.31 Mt (1.44 million st) valued at $56.2 million. Tennessee was the leading producer state with 61 percent of production. It was followed by Texas, Kentucky and Mississippi.

Jan 1, 2005

By E. Topuz, C. Patrick

Longwall face-to-face transfers can cost more than $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high costs make extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. Operations research techniques are used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate, over 35%, of the total US longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation was used to generate models of transfers under Carving conditions; and the economic feasibility of tine-cost tradeoffs in the transfer procedure was investigated.

Jan 1, 1994

By David L. Shearer

INTRODUCTON James Howden first secured an order for two Service Tunnel Boring machines in November 1986. These Tunnel Boring machines were 5.7 and 5.4 metres in diameter and the full length including back up was 215 metres. Manufacture commenced in December 1986 at the Glasgow factories of James Howden & Company with the deliveries to site of the machines in September 1987 and March 1988 respectively. In December 1987 two further orders were secured for the land running tunnels at 8.7 metres diameter. This paper presents some of the challenges in building tunnel boring machines for the Eurotunnel project between Britain and France. The general specifications of the Tunnel Boring machines and length of drives are shown in Appendix 1. DESIGN PARAMETERS The specification given by the Consortium TML on behalf of their client Eurotunnel cleary indicated that cutting of the face should be concurrent with the building of the precast concrete lining rings. In order to do this a telescopic machine was thought to be the best solution. Ground conditions were described as chalk marls of homogeneous nature with the possibility of friable areas and some revelling. A shielded type TBM with open cutter head was chosen together with a telescopic section and a rear

Jan 1, 1989

By K. R. Long

Until it was defunded in 1995, the U.S. Bureau of Mines maintained a Cost Estimating System (CES) for prefeasibility-type economic evaluations of mineral deposits and estimating costs at producing and non-producing mines. This system had a significant role in mineral resource assessments to estimate costs of developing and operating known mineral deposits and predicted undiscovered deposits. For legal reasons, the U.S. Geological Survey cannot update and maintain CES. Instead, statistical tools are under development to estimate mining costs from basic properties of mineral deposits such as tonnage, grade, mineralogy, depth, strip ratio, distance from infrastructure, rock strength, and work index. The first step was to re-estimate ?Taylor?s Rule? which relates operating rate to available ore tonnage. The second step was to estimate statistical models of capital and operating costs for open pit porphyry copper mines with flotation concentrators. For a sample of 27 proposed porphyry copper projects, capital costs can be estimated from three variables: mineral processing rate, strip ratio, and distance from nearest railroad before mine construction began. Of all the variables tested, operating costs were found to be significantly correlated only with strip ratio.

Jan 1, 2011

By R. W. Smith, A. M. Raichur, M. Misra

Mycobacterium phlei has very good potential as a hematite flotation collector. The flotation recovery of hematite is dependent upon the solution pH and concentration of the microorganism. The critical pH for maximum recovery of hematite is around three, which corresponds to the point of zero charge of the microorganism. An excellent correlation between the flotation recovery and bacterial adhesion on hematite is observed. The adhesion of Mycobacterium phlei on hematite can be described by the potential energy of interaction calculations using an extended DLVO theory.

Jan 1, 1994

By Y. C. Kim, I. S. Roditis, P. K. Medhi

P. Mousset-Jones I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reference Kwa, B.L., and Mousset-Jones, P., 1986, "Indicator Kriging Applied to a Gold Deposit in Nevada," Proceedings, Symposium on Ore Reserve Estimation Methods, Models, and Reality, CIMM Annual Meeting, Montreal, Quebec, Canada, May, pp. 185194. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent comparative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging. Reference Lindsey, D.S., 1987, "A Comparative Study: Probability Kriging vs. Ordinary Kriging at the Golden Sunlight Mine," MS Thesis, Department of Mining Engineering, Montana College of Mineral Science and Technology, Butte, MT, May, 81 pp.

Jan 3, 1988

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 13, 2008 at the Charles F. Barber Pavilion of the Museum Convention Center in Leadville, CO. This will be the 21st Annual National Mining Museum and Induction Banquet. The four inductees are Lew Eklund, 76, Carrie Jane Billings Everson (1843-1914), ?Colonel? William C. Greene (1851-1911) and Arthur L. Hawkesworth (1860-1905). Lew Eklund founded Eklund Drilling that is now based in Elko, NV. He invented many designs that play a major role in today?s mining industry. His Cyclo Blower and various sampling devices he designed helped to revolutionize gold deposit exploration by allowing mining companies to effectively sample microscopic gold. Carrie Jane Billings Everson discovered and proved a method for bulk oil flotation concentration of mineral ores, the precursor to modern froth flotation methods of minerals concentration. She patented her process in 1886. In the early 1890s, coworkers built and operated demonstration plants incorporating her bulk oil flotation process. ?Colonel? William C. Greene was responsible for the development of the great copper mining properties of Cananea, Mexico. In seven years, he went from ragged cattleman and adventurer to the greatest captain of industry the borderlands have ever seen. Arthur L. Hawkesworth was a master mechanic for Anaconda Copper. He invented the detachable drill bit. His invention generated tremendous savings for the mining industry in time, in dollars and in safer operating conditions underground. His bit?s long lasting contribution to improved mine economics is immeasurable. The 21st Annual National Mining Museum and Induction Banquet will begin with an open house and reception at 5:30 p.m. followed by the dinner and program at 7 p.m. The inductions will bring to 201 the number of mining ?greats? whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2008

By X. M. Yuan

In the flotation of Zn-Pb ores, sphalerite is floated following copper sulfide activation. In this type of sulfide ore, pyrite is commonly treated as a gangue, and poor selectivity between sphalerite and pyrite/quartz is often reported. But pyrite may also appear in association with gold, and flotation of such auriferous sulfides is of great importance in many countries (e.g. South Africa, Australia). In the cationic flotation of sulfide ores with dodecyl amine, sphalerite can be floated while depressing quartz and pyrite. While in a well-aerated pulp in the presence of lime (especially after oxidation with H2O2) the cationic flotation of pyrite is depressed, oxidation of pyrite in the presence of Na2S makes it floatable with amines even in very alkaline environment.

Jan 1, 2002

By P. R. Desam, J. D. Miller, A. Datta

The flow behavior of bubble-particle aggregates in separation tanks is important for many flotation systems, particularly for wastewater treatment. These aggregates can be considered as the dispersed phase in a continuous liquid phase of water and the flow characteristics determine the efficiency of the bubble separation process. In this work, a general methodology for the computational fluid dynamics (CFD) simulation of a bubble separation tank is described. This system is analyzed by Eulerian-Lagrangian approach. The momentum transfer from the dispersed phase to the continuous phase is quantified using the Particle-Source-In Cell (PSI-Cell) method. With CFD simulations, the effectiveness of different tank design parameters are evaluated in terms of the extent of bubble separation.

Jan 1, 2000