Search Documents

By Todd M. Ruff

The majority of fatalities that occur in road construction work zones in the United States involve a worker being struck by a piece of construction equipment or other vehicle. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these accidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers on foot or other objects. Several cameras and sensor systems are available for this application, and a study was conducted to evaluate these systems on various trucks used in road construction and maintenance. Tests were conducted using sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted using dump trucks during the warmer months to study the effectiveness of the systems in highway work zones. Results show that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in crowded work areas.

Jan 1, 2004

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

By David E. Nicholson

The Bureau of Mines has constructed a special compression chamber for developing stress-strain relationships of mine backfill and simulating the high compressive ground pressures encountered in underground mines. A one-dimensional, or Earth-Pressure-at-Rest model is proposed for backfills subjected to these pressures. Results of the compression tests performed in the chamber indicate that reliable stress-strain relationships can be developed from these tests. The primary objective of the test series was to evaluate the effectiveness of compaction of common backfills in retarding ground closure. Analysis of the stress-strain data shows an eightfold reduction in relative strain in optimum well-graded, compacted backfills over poorly graded, loose backfill material. Analysis of the one-dimensional compression test data also indicates a significant retardation of transmitted stress in dense compacted samples of backfill and natural sands. Although not fully understood, a deformation mechanism is thought to occur at the intergranular contacts in cyclic fashion causing frictional heat loss and a reduction in transmitted stresses in the densely packed materials. The experimental values of transmitted stress are compared with theoretical values of effective stress calculated from the one-dimensional compression relationships developed by Hendron (4).3 These experimental values of transmitted stress compare very closely with the theoretical values of effective stress.

Jan 1, 1968

By Russell E. Griffen

With the development of larger mine-haulage trucks in recent years, the visual field of the driver has diminished correspondingly. Specifically, the operator's lack of direct vision in the right front area and directly to the rear constitutes a serious hazard to personnel in nearby small utility vehicles. Recently developed electronic technology has made it possible to supplement the use of mirrors and fresnel lenses to warn the operator of specific collision dangers in the truck's blind areas. This Bureau of Mines report describes the results of a coordinated contract and in-house research program to develop and test in-mine prototype electronic systems to detect the presence of smaller vehicles within the blind areas of large mine-haulage trucks. Each system utilized transmitters installed on the smaller vehicles and receivers installed on the haulage trucks. Transmitting techniques tested included both low-and high-frequency radio waves. On-vehicle testing established the engineering feasibility of each approach. Further private sector product development to improve reliability and reduce system costs is recommended. Mining companies should consider the advantages of each type of system.

Jan 1, 1988

By L. J. E. Hofer, J. L. Snyder, J. N. Barn, J. E. Chilton, W. E. Thomas

Various silicone materials have been proposed for use in mining environments. The catalytic methane sensors now employed are poisoned by silicone vapors. Activated charcoal and carbon cloth adsorbents will increase the sensor lifetimes in an environment containing significant silicone vapor concentrations. The results of a study of catalytic methane sensor operation with adsorbent materials in hexamethyldisiloxane-air mixtures are reported. Sampling techniques developed for measuring silicone vapor content of mine atmospheres are described.

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 313, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and. January and March, 1932, as published in Reports of Investigations 3l40, 3147, 3l50, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active permissible list: [Austin Red Diamond No. 1, L. F. Gel-Coalite W. L. F. Austin Red-Diamond No. 5, L., F. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No. 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.]

Jan 1, 1932

This Bureau of Mines publication consists of an overview of the mine waste management research currently being conducted by the Bureau. The following papers, given at a Technology Transfer Workshop, emphasize the increasing importance of research related to the safety and environmental considerations of mine waste disposal In recent years. Current work related to legislation passed in the last 10 years and their subsequent standards includes the development of adequate monitoring systems, development of stability and seepage prediction and control techniques, control of runoff water, and control of leaching solutions. Selected topics are included here that cover coal mine waste disposal, embankment slope stability monitoring, flow failures of mine tailings impoundments, and controlled burnout of abandoned coal mine fires. The projects described provide a current documentation of problems being addressed.

Jan 1, 1981

By W. H. Goghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By S. M. Shelton

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well-known that there are largo deposits of low-grade ore in the United States, production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stock piled ore is depleted through inability to obtain adequate supplies from foreign sources. Consequently, a program of laboratory and pilot-plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines. This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series, Report of Investigations 3506, Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent, and C. H. Schack. Other reports will be published as the work progresses.

Jan 1, 1942

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

By John C. Nigro

This Bureau of Mines report summarizes the performance characteristics of a 30-day around-the-clock gasification-pelletizing test conducted in October and November of 1980 with North Dakota Indianhead lignite. Gasification was conducted in a commercial-size, 6.5-it-diam, Single-stage, fixed-bed, atmospheric pressure producer with a rated capacity of about 30 million Btu/hr. Iron oxide pellets made from a commercial hematite concentrate were fired with the low-Btu gas in a 2.8-ft-diam by 35-ft-long pilot plant rotary kiln at a rate of 900 lb of pellets per hour. Gasifier operations at fuel feed rates up to 3 tons of lignite per hour and hematite pellet induration with raw 160-Btu/std ft3 lignite gas are described.

Jan 1, 1982

By Fred P. Giese

Southeastern reserves of titanium ores are large, widespread, and ample for anticipated demand. The leading titanium industries are mining and beneficiating sand deposits, principally in Florida, and manufacturing titanium pigments. Most of the mineral output is consumed by the producers themselves. In 1962, 20 percent of the national pigment capacity was in the Southeast.

Jan 1, 1964

By R. L. Kidd, T. H. Miller

"INTRODUCTION This paper is the seventh of a series of yearly reviews started in 1921 and pre¬sents information gathered in a cooperative investigation undertaken by the United States Bureau of Mines and the University of Utah. It is the purpose of this report to make available flotation—reagent consumption data and other milling information in such a manner as to be of value to the milling industry and to the manufacturer of flotation reagents.These data have been compiled from a survey of about 300 concentration plants in the United States. Much additional information has been obtained from the various offices of the United States Bureau of Mines. Many of the plants covered in the survey made complete reports of their operations, but others were apparently unable to supply this information in sufficient detail to meet the requirements of this report. As a result, some sections of the report are more complete than others. In general, however, the mill reports were much more complete than in previous years, and for the first time it has been possible to calculate average mill recoveries in the treatment of certain classes of ores. As in the past, every effort has been made to conceal individual plant operations.ACKNOWLEDGMENTSIt is realized that the publication of this information is possible only through the assistance of the mill operators, and the authors wish to express their appreciation of this cooperation. Thanks are also due the various field offices of the United States Bureau of Mines, division of mineral statistics, for assistance in collecting this information."

Aug 1, 1931

By A. J. Kraemer

Few important improvements other than the development of cracking processes were made in technical petroleum refining from 1914 to 1919. Refiners were concerned mainly with enlarging their plants and erecting new plants to meet the growing demand for petroleum products. Shell stills operated as a unit or arranged in series for progressive or continuous distillation were the prevailing distillation equipment. Some improvement was made in condensers, but in most refineries of the period coils of pipe immersed in tanks of water were used to condense vapors and cool liquid products of the stills. Heat exchangers to conserve heat and reduce costs were more highly developed at California topping plants than at other plants. In this connection Wadsworth3/states: It is regretted that information concerning the operation of topping plants with eastern and Middle West oils is not available. The writer carefully canvassed the Middle West, but did not find a plant where operation had progressed beyond the early experimental stages and reliable figures could be furnished.

Jan 1, 1941

By G. L. Oldwright, Virgil Miller

"The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada Limited, Trail (Tadanac), Brithish Columbia. The authors are greatly indicated to S.G. Blayrock, vice president and general manager; James Buchman, smelter superintendent; and the staff members mentioned in Report of Investigation 3243. The authors are exceedingly grateful to George Murray, assistant smelter superintendent, for his keen interest, suggestions, and help in carrying out this investigation.INTRODUCTIONThe methods of charign the blast furnaces at Toole and Kelloggs were noted in Report of Investigations 2957 and 3094 respectively. Report of Investigations 2957 cited (4 to 9 inclusive) Hofman's Metallurgy of Lead (p. 226) and the work of A.S. Dwight, Thompson and Sicka, the staff of the Engineering and Mining Journal, and L.D. Anderson, N.F. Collins, in The Metallurgy of Lead (Chas. Griffin, London, 1910) also gives (pp. 247 254) the principles that he believes govern the successful charging of the blast furnace."

Dec 1, 1934

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption of this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 million tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and -is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably arc in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By R. S. Warfield

Following World War II, the rapid increase in both military and civilian activity in the area served by the Alaska Railroad stimulated interest in the availability of local sources of nonmetallic minerals that might be used for building materials. Except for abundant sand and gravel and some pumice, the construction industry of the area depended entirely on high-cost imports for building materials of mineral origin. Because continued rapid growth was anticipated, development and use of local sources of such materials was advocated by both military and civil authorities to reduce the high costs of con¬struction and bolster the unstable economy of the area. The U.S. Department of the Interior began a program On included examining the numerous deposits of nonmetallic minerals accessible to the Alaska Railroad to determine their possible use as raw materials for the construction industry. Preliminary field investigations were made by the Geological Survey. The more promising deposits were subsequently examined and sampled by Bureau of Mines engineers, and the samples were subjected to the laboratory tests necessary to indicate the chemical and physical characteristics of the raw materials or their products. Such field and laboratory investigations were conducted on clay, shale, argillite, limestone, gypsum, and pumice taken from various parts of the area. In initial phasees of the work, done irate 1948 through 1952, many of the deposits examined were suitable for proctoring building materials. Results of the work completed during that period have been published in a Bureau of Mines report3 giving general information and detailed data on more than 35 deposits that were investigated.

Jan 1, 1962

By H. R. Shell

Fluorphlogopite mica was synthesized from inexpensive and abundant olivine, clay, feldspar, and sand (plus K2SiF6). The raw materials were melted in crucibles and in an internal resistance electric furnace. The melts yielded >95 percent mica. The major difficulty encountered was incomplete settling of the highly dispersed ferroalloy. This problem was not completely solved. Reducing agents tried in melts of 300 to 400 pounds were carbon, silicon, and silicon carbide. Carbon slowly reduced the iron of the raw materials, with much fuming. Silicon apparently was oxidized ahead of the melting and was ineffective under the conditions obtained. By far the best reducing agent was silicon carbide. With silicon carbide, fuming did not occur and ionic iron content of the mica flake approached 0 percent. However, even with SiC, the highly dispersed globular iron did not completely separate from the mica portion. The fluorphlogopite made during this investigation should be suitable for metallurgical use. A byproduct ferroalloy containing about 5 percent nickel, 3 to 5 percent chromium, and some cobalt was obtained. Because of the highly dispersed metallic ferroalloy, the mica was not deemed suitable for electrical or electronic uses.

Jan 1, 1962

By Kenneth H. Johnston

This report describes in detail three waterflooding projects and a pressure-maintenance project in Butler and Cowley Counties, Kans., that will be visited on the 1963 annual spring tour of the Kansas-Oklahoma Waterflood Association. Among the unique features of the projects are the flooding of five oil-producing horizons separately with injection water furnished by two water-treating plants. Discussion of the individual projects includes information on their early history, the source and treatment of the injection fluids, oil production decline curves, and the results of water injection on oil production.

Jan 1, 1963