Search Documents

The revised inspection standards or recommendations herein have been prepared for use in Federal inspection of bituminous-coal and lignite mines. They succeed a compilation of similar standards published as Bureau of Mines Information Circular 7268 in December 1943 and employed as a guide in Federal inspections since that time. Important alterations and additions have been made because of changes in mining, practice and temporary shortages of some safety equipment; moreover, several previous standards have been found not generally applicable and have accordingly been deleted. Mining methods and equipment continue to change, and new hazards and new safeguards are introduced. Consequently, these standards are subject to revision from time to time. Questions from the coal-mining industry regarding these standards and suggestions as to changes and additions thereto will be welcomed and considered carefully when the next revision is made. Many constructive criticisms from the mining industry have been considered in preparing this edition.

Jan 1, 1945

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests. Each ore is an individual problem until the association of the gold has been determined. Knowing the problem through the interfering minerals or elements, the solution often is only the application of part of a former known practice as an auxiliary or additional feature. In the treatment plan for most gold ores, it has been the custom to try each of the usual recovery methods or combinations thereof, accepting the best results on a basis of the lowest cost. A better plan includes knowledge of the association of the gold and the various minerals from which it is to be recovered. This presents reasonable foresight into the problems that should be expected and permits some provision for avoiding probable difficulties. The preliminary work should include: Determination of the percentage of free gold with classification showing size of gold particles to be expected; determination of the percentage of gold associated with each mineral and whether it be freed from the mineral by crushing; and an analysis of representative samples of the ore to include other valuable minerals and the form in which they occur.

Jan 1, 1934

By Ronald B. Stotelmeyer

This report summarizes studies of 55 Idaho national forest roadless areas completed by the U.S. Bureau of Mines (USBM) in the period 1966-1992. These roadless areas have been recommended for addition to the National Wilderness Preservation System, proposed as special management areas, or otherwise recommended for study by the U.S. Forest Service or the Idaho congressional delegation. The Bureau of Mines' studies indicate which parts of the roadless areas contain mineral resources. They also show where mining and prospecting are likely to occur in the future, where mineral production has occurred in the past, and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character.

Jan 1, 1994

By Audrey A. Soja

The Bureau of Mines investigated beryllium resources, production methods, and production costs to estimate the quantity of beryllium available for future use. Eight mining districts and 12 deposits are included in the study; lack of data precluded the evaluation of resources from 6 nonproducing and undeveloped deposits. The study revealed that demonstrated beryllium-bearing resources should be sufficient to meet domestic needs and those of other market economy countries (MEC's) well into the 21st century. Total demonstrated beryllium-bearing in situ resources from MEC's are estimated at 118 million metric tons (Mmt) of ore containing approximately 33,000 mt beryllium metal. Approximately 111 Mmt ore containing 29,000 mt beryllium was included in the cost analysis and availability sections of this study. Three Brazilian districts currently produce beryl ore, and one domestic company, Brush Wellman Inc., produces bertrandite ore. Brush Wellman Inc. owns and operates the only MEC facility in the Western Hemisphere for extracting beryllium values from beryl and bertrandite and is the beryllium industry's only fully integrated corporation.

Jan 1, 1986

By E. M. J. Alenius

This paper describing the mining practices at the United Verde open-pit mine at Jerome, Ariz., is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. The purpose of this paper is to present the methods used in developing and operating the mine, and to discuss the problems encountered.

Jan 1, 1930

By Peter Grandone

Bureau of Mines engineers engaged in studying stimulative methods of recovering oil have been making a series of tests on the effectiveness' of methods that may be applied in water flooding oil-bearing sandstones. The report gives the test procedures and results of a study of the rates and pressures used for injecting water into several sandstone formations in the Mid-Continent fields for the purpose of learning more about the mechanics and efficiency of the flooding process and to provide useful information for operators of water floods in this area.

Jan 1, 1949

By R. A. Franks, G. F. Friel, J. C. Edwards, A. C. Smith

An evaluation of a nuisance-emissions-discriminating smart mine fire sensor system was made in an operating coal mine. These field evaluations were conducted to determine the sensor system's ability to discern nuisance emissions, such as diesel exhaust, emissions from flame cutting and welding operations or hydrogen gas from a charging station, from real fires and to compare the number of falsely reported fire alarms generated between the sensor system and a standard carbon monoxide (CO) monitor. The sensor system's ability to operate successfully in the working environment of an operating coal mine was also evaluated. The smart mine fire sensor system consisted of four sensors whose data outputs were fused with the use of a neural-network-type computer program. Long-term trials were conducted in a haulage way, a belt entry, and a track entry. The system functioned successfully in the belt entry, in accordance with its developmental goals, where the sensor system even discriminated events not anticipated during development. It was not totally effective in the haulage way and track entry, though, due to a combination of significant diurnal air temperature variations, dust, and mechanically induced vibrations. Also, deteriorating rib conditions contributed to operational problems in the haulage way evaluation. In general, the smart mine fire sensor provided nuisance emissions discrimination and was shown to be a viable new approach for mine atmospheric monitoring, enhancing miner safety. This paper describes the in-mine evaluation of the smart mine fire sensor system and discusses recommendations for improving the system.

By W. H. Rinkenbach, C. A. Taylor

"Among the recently patented detonating compounds that have been suggested as substitutes for the commonly used fulminate of mercury is the normal lead salt of trinitroresorcin, or styphnic acid. As no data concerning its use or practi¬cability were available, a study of its properties was made in the explosives laboratory at the Bureau of Mines experiment station at Pittsburgh, Pa. This paper embodies the results obtained.Normal lead trinitroresorcinate was first prepared and patented*** by Herz; it probably found some use during the World War, but no record of its performance is available,Preparation of Lead Trinitrpresorcinate.In his patent specifications, Herz states that the normal salt may be obtained in a quantitative way by precipitating a multiple of the equivalent weight of the lead salt of a strong inorganic acid - such as lead nitrate - in the presence of a weak organic acid - such as acetic acid - by heating with a Teak solution of the alkali-metal salts or alkaline-earth salts of trinitroresorcin. Herz gives the following example: 245 grams of dry trinitroresorcinand 290 grams of crystalline sodium carbonate are dissolved in in 18.8 liters of boiling water, to which 77 c.c. of glacial acetic acid is added. The toiling solution is mixed with a boiling solution of 650 grams of lead nitrate in 1.4 liters of water, stirring rapidly; and the mixture is boiled for two minutes, after which it is cooled quickly with constant stirring. The precipitated crystals are then filtered off, washed several times with cold water, and dried."

Oct 1, 1923

By Paul M. Tyler

Graphite occurs in many places in the United States, but previous to 1914 the domestic production amounted to only 15 to 20 per cent of the natural graphite consumed in this country. Including artificial, graphite, the proportion was about 25 per cent. During the World War the production of both natural and artificial graphite increased until, in 1918 it, contributed more than one-half of the available supply, and since 1919 the proportion has not fallen below 40 per cent. Except during the war period, however, this apparently increasing independence has not been due to any large increase in production from domestic mines. It simply reflects a larger output of artificial graphite and reduced imports of Ceylon lung and chip, grades which have never been produced in substantial quantity in the United States. DOMESTIC DEPOSITS3 American graphite deposits, though numerous and often large, are characteristically low-grade. They constitute an abundant source of potential supply, but in normal times they have proved relatively costly to work, and even at the same price the various products have never been able wholly to displace certain imported qualities, notably crucible grades from Ceylon and pencil graphite from Mexico.

Jan 1, 1929

By M. H. Marvin

This report presents the results of a program to develop backfilling techniques to mitigate undesirable effects of hydraulic borehole uranium mining. Large underground cavities, formed during the borehole mining process, can be backfilled to prevent ground subsidence and to allow mining of adjacent uraniferous sandstone. Three backfilling techniques were tested in the laboratory and in the field: bulk dumping of slurry into the borehole from ground level, slurry injection under water, and slurry injection above the cavity water level. These techniques were tested with sand and with sand and one percent cement (by weight) mixtures. The project was accomplished in four tasks: equipment preparation and transport, mining operation to generate a full-sized cavity, backfilling operation, and assessment through core samples and subsidence checks. The concentrations of cement mixed with sand proved to be inadequate to bond the sand. Bulk dumping resulted in a 30-degree angle-of-repose, much too steep to completely fill the cavity. Both slurry injection techniques filled the cavity satisfactorily. However, underwater injection is the recommended backfilling technique because the borehole water level does not need to be pumped down during backfilling. The borehole itself was filled by bulk dumping of slurry. In conclusion, backfilling of borehole mining cavities is entirely feasible, and the preferred method is slurry injection under water.

Jan 1, 1979

By Peter C. Wood

This report describes research directed toward the preparation of chemical oxygen (02) sources which exhibited improved 02 storage and reaction characteristics when compared to potassium superoxide (KO2). The initial focus of the research was the preparation of calcium superoxide (Ca(02)2) by the disproportionation of calcium peroxide diperoxyhydrate. The Ca(02)2) was characterized by chemical, thermal, and x-ray analyses. Several methods for scaling up the Ca(02)2 synthesis process were studied. Next, the reactivity of Ca(02)2 toward humidified carbon dioxide (C02) was evaluated and was compare o that of K02 under flow-test conditions approximating those existing in portable breathing apparatus. The reactivities of mixtures of K02 and Ca(02)2 or lithium peroxide towards humidified CO2 were also studied. Finally, an analysis of two commercial, K02-based, self-contained self-rescuers was conducted to determine the potential weight and volume savings which would be possible if Ca(02)2 or a mixture of K02 and Ca(02)2 were used as a replacement for K02.

Jan 1, 1983

By D. P. Lindroth

The Bureau of Mines is engaged in research on ground probing radars for detection of geologic hazards in advance of mining. Penetration distances and interpretation models depend on the dielectric properties and wave propagation characteristics for coal measure stratified media. Relative dielectric constants and dissipation factors were measured under ambient conditions for Pittsburgh Seam coal measure rock over the frequency range of 20 to 100 MHz by the susceptance-variation method. The rock types measured were representative sedimentary rock located above the Pittsburgh Coal Seam. Extreme values for the computed attenu-ation distance ranged from 1.7 m at 100 MHz for siltstone to 230 m at 20 MHz for a particular limestone.

Jan 1, 1984

By A. B. Needham

In November 1940, the Bureau of Mines started exploration of the Three Blacks manganese properties - Black Diablo. in Pershing County and Black Eagle and Black .Rook in Lander County. The purpose was to determine possible reserves of manganese in the deposits. It is reported that a small amount of manganese was mined from the Black Diablo during World. War 1. No mining except that necessary for assessment work had been done on the Black Eagle. Shipments were being made from the Black Rock deposit to a concentrator at Vain, Nev., while the Bureau's development work was progressing. The Black Diablo deposit consists of one patented claim owned by the Charleston. Hill National Manes Co. Mary L. Clough of Winnemicca, Nev., president. The deposit is about 20 miles by a gravel and dirt road southwest of Golconda, a town on U. S. Highway 40 and the Southern Pacific Railway, Pershing County, Nev. The deposit lies at an elevation of about 5,600 feet on the east flank of the north-south trending Sonoma Range. The property was leased by Messrs. Hollis Chatwin, T. E. Chatwin, and R. H. Richards of Salt Lake City and Mammoth, Utah. The lessees installed a crusher and erected an ore bin below the open cut on the deposit and mined and, shipped about 5,000 tons of about 30 to 52 percent manganese ore to the Columbia Steel Co., Provo, Utah.

Jan 1, 1950

By Jon A. Hummer, Emanuele Cauda, George H. Schnakenberg, Aleksandar D. Bugarski, Samuel J. Janisko, Larry D. Patts

A series of engine/dynamometer tests was conducted to assess the effects of three types of uncatalyzed diesel particulate filters (DPFs), a diesel oxidation catalytic converter (DOC) and three types of high temperature disposable filter elements (HT DFEs) on the concentrations and size distribution of diesel aerosols and concentration of nitric oxides in underground mine air. Tests were conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of these and other control technologies directly in an underground environment. The aforementioned technologies are evaluated by comparing the aerosol and gas measurements in the mine air 60 m downstream of the exhaust from a naturally aspirated, mechanically controlled engine fitted with the tested systems or muffler and operated at four steady-state engine speed and power modes. The tested DPF and HT DFE systems caused a 10-fold reduction in total mass concentrations of aerosols. The size distribution and number concentration measurements showed that all tested DPF systems and HT DFE elements effectively removed accumulation mode aerosols (D50>30 nm) for all test modes. An increase in peak number concentrations of nucleation mode (D50>30 nm) diesel aerosols is evident for some of tested DPF systems when engine was operated at high-load modes. The effects of uncatalyzed DPFs on nitric oxide (NO) and nitrogen dioxide (NO2) concentrations are found to be minor. A four-fold increase in percentages of NO2 in total nitrogen oxides (NOx) over baseline case was observed for the DOC when the engine was operated at high-load modes. The findings from this study should contribute to better understanding the potential for various control technologies to reduce exposure of underground miners to nano and ultrafine aerosols. In addition, detailed physical characterization of diesel aerosols made directly in occupational setting should foster a better understanding of the health risks associated with exposure to nano and ultrafine diesel aerosols.

By William W. Adams

Accidents to men employed in the quarrying and related industries of the United States were more numerous, absolutely and relatively, in 1937 than in 1936. Fortunately, the entire increase was in the category of nonfatal injuries, as accidents causing death declined in number and in proportion to the number of man-hours worked. Employment increased. More men were employed, more man-days and man-hours were worked, and the average employee had more hours of work than in 1936. Reports covering all commercial operations showed that 84,094 men were employed an increase of 5.1 percent over 1936. The number of man-hours of work performed by the industry was, 158 millions, an increase of 7.6 percent. Seventy-seven men were killed by accidents, a, reduction of 14 from the year before, and 6,348 men were injured and disabled for more than the remainder of the day on which the accident occurred, 11 percent more than in 1936. The fatality rate of 0.49 per million man-hours of exposure in 1937 compared favorably with the rate of 0.62 for the previous year, whereas the non-fatal-injury rate of 40.10 was 3.2 percent higher than the rate of 38.87 for 1936.

Jan 1, 1940

A computer system for calculating the illumination on coal mine surfaces due to machine-mounted lights is described. Utilizing numerical models of mining machinery and measured data on luminaire output characteristics, the program computes the ft-candle levels incident on the mine entry surfaces for any desired machine/luminaire/ entry configuration. Shadowing effects of the machine are taken into account. Results are provided at 2 ft. intervals on the face, left and right walls, floor and roof. The system operates, interactively from a Tektronix 4014 graphics terminal which handles all input/output functions. The software is installed on a Cyber 74 computer that communicates with the terminal via telephone line.

Jan 1, 1978

By James Westfield

Following is a resume of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction o1 injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bitumi¬nous coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority (under Executive Order 9728) was removed June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1959

Underground coal mine tracked vehicles have been studied to determine the state of the art and how brakes might be added to the coal haulage cars. Specific areas of interest are: brake sys terns, couplers, car trucks and car handling procedures. Problems related to adding brakes to the haulage cars appear to be: the limited amount of room to mount the brakes on the cars, brake line connection between rotary dump cars, achieving desirable braking characteristics without over complicating the system and keeping the installation cost to a reasonable figure. This document combines the information contained in the first issue of the "State-of -the-Art of Underground Coal Mine Tracked Vehicle Brake Systems," BRL Report No. 6080, with that contained in a subsequent monthly report.

Jan 1, 1973

By Steven J. Schatzel, Robert B. Krog

Frictional ignitions are defined as the ignition of a flammable mixture of methane and air that is initiated by frictional heating. Ignitions created through the addition of energy from open flames and exposed electrical circuits are not included in this analysis. Energy released in a roof fall that creates a spark and ignites a methane mixture would be considered a frictional ignition. Frictional ignitions represent the majority of all ignitions in underground coal mines. Over the study period of 1983 to 2005, a total of 1993 ignitions were reported in underground bituminous coal mines in the United States, of which 1589 were frictional ignitions. Reportable ignitions to the Mine Safety and Health Administration (MSHA) are any unintentional occurrences of flame underground regardless of duration. Frictional ignitions were reported in 155 mines and 13 states. Continuous miners represented the largest source for frictional ignitions with 1090 (68.6% of all frictional ignitions). Longwall mining operations represented the highest concentration of frictional ignitions during this study period with 1365 frictional ignitions (85.9% of all frictional ignitions). The 17 mines with the most frictional ignitions were all longwall mining operations and had 1130 frictional ignitions (307 from the shearer) that represented 71.1% of the total. In 1983, mines with frictional ignitions represented 6.9% of operating underground mines and 36.6% of total underground coal production. The percentage of operating underground mines with frictional ignitions and their total production has increased steadily and in 2005 represented 9.8% of active mines and 46.2% of underground coal production. The three coalbeds with the highest number of frictional ignitions (Blue Creek, Pittsburgh No 8, and Pocahontas No 3) had 1049 ignitions that represented 66.0% of all frictional ignitions. The three states with the highest number of frictional ignitions were Alabama (710), Virginia (247), and Pennsylvania (242) that represented 75.5% of the total. Frictional ignitions peaked in 1991 with a high of 114. In 2005, only 34 frictional ignitions were reported. If only frictional ignitions that occur at the face are considered, there have been no fatalities since 1983. Since this time, there were 33 ignitions that caused 53 workers to lose a total of 2912 working days. When including ground falls, then there have been four frictional ignitions with one incident causing two fatalities and injuring eight workers. From 1983-1991, underground productivity and the number of frictional ignitions increased. However, productivity continued to increase from 1991-2000 while total frictional ignitions fell, thereby disproving this connection between productivity and frequency of frictional ignitions. Ninety percent of all frictional ignitions occurred in underground coal mines that liberated more than 393 L/s (1.2 MMcfd million cubic feet per day) of methane through the main ventilation system. Although methane production is not the determining factor for the occurrence of frictional ignitions, it is a good indicator of the anticipated frequency.

By L. D. Schmidt, Wm. Seymour, W. S. Landers

"INTRODUCTION The relative value of the various individual physical and chemical properties of coke as a measure of its performance in the blast furnace as aroused considerable controversy but it is generally agreed that uniformity in these properties is extremely important if maximum mum pip-iron production is to be attained. The control of,the bulk density or weight per cubic feet of the coal charge in the coke ovens is a major, and frequently overlooked, factor in producing a uniform product and in efficient operation of the coke plant.This report presents a brief discussion of the general problem of bulk-density control and the results of tests on samples of coke-oven charges from several operating plants experiencing difficulties due to lack of adequate control. These tests covered the effect of moisture and oil content on the bulk density of the coal. Some tests on the effect of a wetting agent and furnenous of gained were also made. A description of the methods used to determine the bulk density of the coals studied in this investigation and of the methods used to apply oil to the coal at byproduct-coke plants are included in this product. No theoretical analysis of the data presented in this report, because the primary purpose of the investigation was to obtain data of immediate practical value to the plants concerned."

Apr 1, 1945