Search Documents

By F. S. Boericke

"INTRODUCTION The mineral found in natural-chromite deposits is never pure Fe0.Cr203, but rather one in which the Fe0 and Cr203 are in part replaced by Mg0 and A1203, respectively. The purest gravity concentrates from many domestic de¬posits consist of a mineral referred to as ""picotite,"" in which this isomorphous replacement is such that the ratio of chromium to iron is low. The Bureau of Nines has investigated methods of chemically beneficiating ores that contain too much iron to be classed as ""high-grade"" chromite 3/ Early investigations 4/ demonstrated that high-iron chromite or picotite ores can be roasted with carbon to obtain selective reduction of the contained iron, and that most of this reduced iron can be removed by acid-leaching the roast products to produce residues of higher chromium-to-iron ratios. tests 5/ indicated that commercially acceptable reaction rates cannot be obtained at roasting temperatures below 1,3000 C., using solid carbon as reducing agent. By this high-temperature reduction and subse¬quent acid-leaching, however, all ores investigated, regardless of the original composition, readily yielded residues considerably better than the minimum specifications for high-grade chromite.In an effort to obtain satisfactory reduction of chromite at lower temperatures, liquid and gaseous seducing agents were tested with varying success. Of the several reducing agents used, methane appeared to be the most promising and was shown to be highly effective at temperatures between 1,000º and 1,100º C., roughly 300º below the roasting temperatures necessary in solid carbon reduction. Further experiments indicated that mixtures of methate with some diluent (hydrogen or other nonoxidizing gas) gave better reduction than did methane alone."

Feb 1, 1946

By H. Kenworthy

The objective of this research was to develop methods and determine conditions under which metallic sulfides with lower boiling points than sphalerite may be removed from zinc sulfide concentrates by volatilization. A higher percentage of extraction of lead, cadmium, and germanium than is common in current practice was sought. The investigation, conducted by the Metallurgical Branch of the Minerals Technology Division, Region VI, showed that, under proper conditions, it is possible to remove over 90 percent of the lead, cadmium and germanium as an enriched sublimate. The uses of lead, and cadmium to a lesser extent, are well-known. Although germanium was discovered in 1886 by C. Winkler, commercial use has been achieved only in recent years. The amount consumed per manufacturer unit is so small that the price of germanium may still be quoted by the gram. The electronic industries have been the chief consumer of this semiconductor. Germanium is sold largely to the fabricator as a dioxide for reduction to metal and subsequent processing into wafers for use in diode and triode electronic tubes. Extensive research at Purdue University during World War II led to the first practical use of germanium.

Jan 1, 1952

By G. E. McElroy

Changes in existing airway and fan-installation conditions offer the most common opportunities for effecting economical operation of mine ventilating systems, but the largest possibilities for securing this result lie in the original design of the main airways for efficient service. Formulas, and. charts for their graphical solution, are presented herewith for the determination of the elements of airways design when the conditions of service are known, or may be roughly approximated. Although the analyses are made with particular reference to metal-mine airways, there is no essential difference between metal and coal mine main airways, and the methods presented are equally applicable to both. Little attention is paid to designing airways for maximum economy in the ventilation of metal mines. Most of the openings used as main airways are originally designed and used for transportation and other operating purposes. Even where openings are made primarily for ventilation, the possibility of their future use for other operating purposes, or even custom alone, usually results in the selection of a size and shape similar to those of existing openings. Natural conditions, such as heavy ground, often seriously limit the size of opening that can be maintained without excessive expense; and various operating factors, such as velocity limitations on traveling roads, often dictate size requirements in excess of those required for economy in ventilation only. In metal mines the main airways are, as a rule, too small rather than too large for economic service, with the general result that the quantities in circulation are often less than the mine's proper requirements over long periods, even though excessive amounts of power are applied in an effort to remedy conditions.

Jan 1, 1932

By Stephen R. Iverson

Mineral deposits examined in and near the Raywood Flats RARE II area have low potential for development. The Mill Creek Mine (fig. 1), has produced about 14,000 tons (13,000 t) of marble, and another 5.5 million tons (5.0 million t) of marginal marble reserves suitable for lime, chemicals, and cement production are estimated to remain at this deposit. However, nearly all the marble is outside the study area. The deposit is marginal because alternate sources of marble are closer to markets. A tungsten occurrence in the marble is too small and low grade to be considered a resource. Ten tons (9.1 t) of uranium- and thorium-bearing material have been mined from a pegmatite dike at the St. Patrick Mine. However, this occurrence also is too small and low grade to be considered a resource. More than 400 lode and placer claims have been located in or near the study area. There are no current claims or mineral, oil and gas or geothermal leases.

Jan 1, 1983

By T. T. Read, T. L. Joseph, F. H. Royster

In a preliminary study of the beneficiation of iron ores conducted by the Bureau of Mines, one of the authors (T. T. Read) found it necessary to ascertain, if possible, how much effect a decrease in the silica content of an iron ore has upon the cost of making pig iron from the ore. In the beneficiation of iron ores the most important impurity to be removed is usually silica, and the amount that can be expended on a beneficiation process to reduce the silica content of the ore is obviously determined by the amount of increase in the value of the ore after beneficiation. The price that can actually be obtained for a beneficiated ore is, of course, a matter of negotiation between the seller and the buyer, but since the relative value of different grades of iron ore must be chiefly based upon the cost of making pig iron from them, an approximation as to the effect which decrease in the silica content of ore has upon the cost of snaking pig iron is an important guide in estimating what probable average gain will result from subjecting an ore to a beneficiation process. A search of the literature failed to reveal any detailed statement on this important topic, but fortunately the data are at hand to permit making an approximate calculation of the probable effect. For the purpose of the calculation assume three iron ores with the following composition (natural):

Jan 1, 1924

By H. C. Fuller

A method was devised and developed by the Bureau of Mines for decomposing manganese sulfate at significantly lower temperature than that required by the conventional procedure of using heat alone. This technique, called the partial reduction method, effected decomposition at 700° to 800° C, as compared to 900° 1,000° C normally required. The process consisted of heating, in the absence of oxygen, a mixture of manganese sulfate and a controlled quantity of a reducing agent. The suitability of commercial-type equipment was tested in laboratory-size models of an externally heated rotary kiln, a r bbled muffle-hearth furnace, and a fluidized-bed reactor. The rabbled-hearth furnace gave the best results with the least operating difficulty produced a gas containing more than 80 percent SC and eliminated 96 percent of the sulfur when coal was used as the reductant. Sintering of the powdery decomposition product produced an agglomerate containing, in percent, 63.6 Mn and 0.4 S.

Jan 1, 1966

The Technology Transfer Seminar on Mine Communications held on March 21-77, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

By Stephan Stecura

Crystallographic modifications and kinetics of solid-state phase trans-formations were determined for five rare-earth" sesquioxides--La2O3, Nd2O3, Sm2O3, Eu2O3, and Gd2O3. Oxides used for crystal modification studies were prepared by thermal decomposition of the following high-purity salts of the five rare-earth elements--carbonates, chlorides, fluorides, nitrates, oxalates, and sulfates. X-ray diffraction patterns of the cubic and hexagonal oxides were indexed by a graphical method and patterns of the monoclinic oxides by Ito's method. The kinetics of crystallographic transformation were determined by high-temperature X-ray diffractometry. The kinetic data were interpreted using a shrinking sphere model. All of the transformations followed first order kinetics. Activation energies were calculated by application of the Arrhenius equation. These solid-state phase inversions were concluded to occur by a reconstructive transformation mechanism.

Jan 1, 1965

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines on the spontaneous combustion of U.S. coals. Approximately 11 pet of U.S. underground coal mine fires are attributed to spontaneous combustion. The relative self-heating tendencies of 24 coal samples were evaluated in an adiabatic heating oven. Minimum self-heating temperatures (SHT's) in the oven ranged from 350 C for a lignite and high-volatile C bituminous (hvCb) coal, to 1350 C for two low-volatile bituminous (lvb) coals. An empirical expression was determined predicting a bituminous coal's minimum SHT in the adiabatic oven based on the coal's dry ash-free oxygen content. Several factors that can affect the self-heating process were also evaluated. The self-~eating tendency of a coal increased when the coal was dried and exposed to humidified air, and was dependent on the particle size and oxygen concentration of the air. A new moderate-scale apparatus is described, in which the self-heating tendencies of larger coal samples, 3 kg, can be evaluated. The minimum SHT's of two coals were determined and the results were in good agreement with those found in the adiabatic oven. Finally, results of a test in the moderate-scale apparatus indicated a strong dependence of the self-heating rate of a low rank coal on the moisture content of the air.

Jan 1, 1987

By B. C. Parks

This is the first of a series of reports on the relation between microscopic composition and chemical and physical properties of banded bituminous coals. It describes the relation between microscopic composition and behavior during thermal decomposition of a heterogeneous, high-volatile A bituminous coal from the Chilton bed in West Virginia. The standard free-swelling test was used as a simple means of studying the effect of heat on the coal. Although swelling indexes are not precise indicators of coal behavior in the coke oven and have limited value in caking investigations, they are reliable for predicting expansion of coal in a fuel bed and have practical value in the study of fuels. The swelling test also supplements other useful laboratory tests for determining the plastic and expansion properties of coal.

Jan 1, 1957

By J. A. Kost

A dust-control manual was prepared for use by mine operations personnel. The manual documents state-of-the-art control techniques, dust sampling, and use of personal protective devices. Content addresses advantages/disadvantages of control techniques, design and operating specifications, and implementation and maintenance guidelines. An indexed list of selected references is also included. In addition to the completed manual, this report documents work performed in the course of its preparation.

Jan 1, 1981

By W. L. Dare

This report is one of a series published by the Federal Bureau of Mines to describe methods and costs of mining uranium on the Colorado Plateau. The Navajo Uranium Division of Kerr-McGee Oil Industries, Inc., mines uranium from several deposits of carnotite-type ores, which lie buried in the Lukachukai Mountains on the Navajo Indian Reservation, Apache County, Ariz. The country is rugged and isolated Constructing and maintaining roads has been a continuous task. The ore bodies occur within the Salt Wash member of the Jurassic Morrison formation and are similar to other such deposits on the plateau. The current mining activity in the Lukachukai Mountains is a result of uranium-ore discoveries in 1949, although the Navajos undoubtedly knew of the outcrops of yellow uranium minerals long before that time. The ruggedness of the country and the heavy soil cover over much of the surface hampered prospecting, but probably the main reason the ore was not found sooner is that no one took the trouble to look for it in the Lukachukai Mountains.

Jan 1, 1961

By C. H. Riggs

This report of a petroleum-engineering study of the Flat Rock oil field, Osage County, Okla., describes the geology, reviews the production history, and estimates remaining oil reserves. The Flat Rock field in the southeastern corner of Osage County approximately 6 miles northwest of Tulsa. Okla., was discovered in November 1904. The field was one of the first of many Bartlesville-sand fields developed in eastern Osage County during the early part of the 20th century. Although substantial oil reserves remain in the pressure depleted sands in some parts of the field, their economic recovery by water flooding will require careful consideration of the many factors involved.

Jan 1, 1954

By D. Christofferson

This final report documents the cooperative efforts of the Engineered Systems Division and the Mining Equipment Division of FMC Corporation during performance of Bureau of Mines Contract H0252091. Improved operator compartments incorporating overhead canopies, logical arrangements of controls, and design features offering greater operator comfort were developed and retrofitted to the FMC 320A roof bolter and 6L shuttle care The vehicles were evaluated in underground operations at separate mine sites. The successful evaluation has resulted in incorporation of the designs as standard features of the 320A roof bolter, and the 5L, 6L, and 10L shuttle cars.

Jan 1, 1978

By Robert S. Becker

The results of a laboratory investigation of coal cutting mechanics and noise is presented. These experiments were performed using a linear cutting apparatus that operates over a broad cutting speed range. The influence of several coal cutting parameters on the noise, force, productivity, and specific energy associated with linear cuts is ascertained. Some basic theoretical aspects of coal cutting mechanics and noise generation are discussed, and the results of the laboratory experiments are used to Formulate analytical models of the coal cutting forces and noise. The analytical model For coal cutting noise is then generalized to account for the more important effects of rotary cutting. Based on the generalized model, an estimate of the sound pressure level at an operator's position is made for a typical continuous mining machine. It is concluded that by employing linear rather than rotary cuts, using deeper depths of cut, slower cutting speeds, and more efficient cutting tools, it is possible to reduce the level of coal cutting noise, as well as Provide benefits to other important areas of underground health and safety.

Jan 1, 1980

By R. R. Sayers

Although the attention of those interested in diseases peculiar to mining as teen focused recently on one duct disease - silicosis - other respiratory diseases may cause more suffering and economic loss. The increased incidence of these diseases usually is attributed to exposure to abnormal air conditions underground, such as sudden changes from high to low temperatures, excessive dust, and noxious gases. The principal respiratory diseases to which the mine is subject axe bronchitis, influenza and pneumonia, pulmonary tuberculosis, anthracosilicosis, and. silicosis. Although the mortality statistics in some of the tables included in this paper are old they have been corroborated by later, lees complete data Bronchitis Bronchitis is en inflammation of the bronchial tubes due, among other causes, to the inhalation of irritants such as dusts (organic and inorganic). Occupations that entail exposure to atmospheres polluted, by irritating gases carry with them the risk of bronchitis. According to Collie (1), it cannot be distinguished clinically from bronchitis occurring among the general population, and its association with tae inhalation of dust or gases usually is unrecognized.

Jan 1, 1941

By Thomas C. Denton

In 1965 Africa maintained its position as a region of the world essential to advanced non-Communist nations for supply of vital metals and minerals. The position stemmed from the fact that Africa produced in large quantity a number of key minerals of which either or both resources and production capacity elsewhere did not approach the needs of the free world. The Republic of South Africa alone contributed more than three quarters of the gold mined in the entire non-Communist world besides an estimated 60 percent of metals of the platinum group and the entire new supply of amosite asbestos, and Africa as a whole was nearly the non-Communist world's only source of gem and industrial diamond. Africa also accounted for 83 percent of non-Communist world cobalt production. Besides these massive contributions, Africa in 1965 provided 50 percent or more of the new supply from non-Communist countries of the following mineral commodities: Lithium minerals, corundum, manganese ore: and chromite, and over 20 percent of new supply from non-Communist countries of columbium-tantalum concentrates, antimony, beryl, vanadium, phosphate rock, and copper. Africa also accounted for 18 percent of the non-Communist world's output of uranium, 14 percent of its tin, 11 percent of its lead, 9 percent of its zinc, and 8.9 percent of its crude oil output. With respect to chromite, at yearend Africa's reserves of the mineral were far larger than those of all other non-Communist regions combined. This probably also held true for manganese ore. In the case of crude oil, the fact that Africa's share of non-Communist world output was 1.6 percentage points greater than in 1964 was significant, particularly inasmuch as the output rate was continuing to increase at yearend.

Jan 1, 1967

By John L. Miller

The synthetic fluormicas may be divided on the basis of silicon content into tetrasilicic, trisilicic, and disilicic. Properties of lead and barium disilicic fluormicas were determined to characterize these two representative members of the disilicic group. Properties described include unit-cell parameters from X-ray diffraction, optical data, chemical composition, density, melting point, and mechanical and dielectric properties. Both the lead and the barium micas were typically monoclinic; neither was sufficiently cleavable to yield usable mica splittings. Both yielded polycrystalline, machinable ceramics with excellent mechanical and dielectric properties.

Jan 1, 1963

By Richard C. Moore

The U.S. Bureau of Mines contracted a study to estimate what effects the underground mining of thick coal seams in the western United Slates would have on the surrounding water resources. Potential coal fields in the western United States where this type of mining might occur were identified. The foreign literature was searched for studies of effects on hydrology from thick seam underground coal mining. Based on the limited information obtained from the foreign literature, estimates of the effects of this type of mining on the ground and surface water in the western states were made.

Jan 1, 1980

By Alton B. Cook, G. B. Shea

"INTRODUCTION In February 1945, Captain (now Commodore) W. G. Greeman, U. S. N., Director, Naval Petroleum and Oil 3hale Reserves, requested the Bureau of Mines to assist the Navy in its wartime development of Naval Petroleum Reserve No. 1, Elk Hills field, Calif., to assure adequate supplies of petroleum products in the Pacific theatre. Unit Operation 4/,engineers desired pressure volume-temperature and viscosity data on the reservoir oil in the shallow oil zone to augment data previously obtained for the purpose of calculating reservoir performance and oil reserves. Accordingly, arrangements were approved by the Operating Committee far, the Bureau of Mines to proceed with a program of field sampling and laboratory determinations designed to obtain the desired information.To carry out the assignment, the Bureau transferred the necessary person¬nel, subsurface pressure, temperature, and sampling instruments, and laboratory equipment for analyzing subsurface oil samples from the Petroleum Experiment Station, Bartlesville, Okla., and the San Francisco, Calif., office and set up a temporary field headquarters in the Elk Hills. The program of work as out-lined by Unit Operation required the 6 months period March-August 1945 to complete during which time individual reports comprising data on pressure-volume-temperature relationships and reservoir oil viscosities as determined on subsurface oil samples and recombined oil and gas samples for 5 selected wells were submitted to Unit Operation.This report is a summary compilation of the data contained in the original reports supplemented by correlations of some of the physical properties of the reservoir oil with the A.P.I. gravities of the produced oil. The report also includes material-balance calculations relative to one of the oil horizons in the shallow zone. The Bureau of Mines believes that publication of the results of these analyses is a worthwhile contribution to the petroleum literature and of particular interest to the California industry."

Apr 1, 1947