Search Documents

By Robert H. Merrill

This report contains a summary of the various studies made to determine the structural design of the production mine area of the Oil-Shale mine, Rifle, Colo. Prior to this investigation, it had been determined from a study of the geology, the structure of the deposit, and mining costs that the deposit should be mined by open stoping. The problem remained to determine the maximum safe roof span, the optimum extraction ratio, and the size of the pillars. These factors were determined from a study of the geologic structure of the deposit, the physical properties of the oil shale, and the magnitude and distribution of the stress around proposed underground openings. The latter was determined from both theoretical calculations and model studies. Safe roof spans, pillar sizes, pillar contours, and optimum extraction ratios were calculated from elastic theory and the physical properties of the mine rock. Safe roof spans, pillar sizes; and time effects were determined by Wright and Bucky by testing mine models in a centrifuge. The models were made from rock specimens taken from the proposed mine roof and pillars. The results from both studies agreed.

Jan 1, 1954

By Walter E. Pittman

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

Jan 1, 1982

By J. L. Holman

The Bureau of Mines has extended its previous development of cast Mn-Cu damping alloys to powder metallurgy (P/M) consolidation of alloys containing 55 to 75 wt-pct Mn. Blends of minus 200-mesh elemental powders were compacted cold in directional and isostatic presses. With 1 pct binder, typical green densities ranged between 76 and 80 pct of theoretical when pressing at 30 or 48 tsi. Green strength increased with compacting pressure and copper content. As-sintered tensile strengths ranged to 60,000 psi fox a hydrogen, sintered 60Mn-40Cu alloy, along with 5-pct elongation. Sintered densities ranged between 90 and 96 pct of theoretical. Sintering (a as effective when holding for 1 hr at maximum temperatures of 900° to 1,040` C, dependent on composition. Strength and ductility were considerably lower than for equiva¬lent cast alloys. When aged to the damping condition, alloys containing 60 to 70 pct Mn exhibited >40 pct specific damping capacity (SDC) at 5,000-psi stress, considerably higher than values reported for equivalent cast material. Effects of 1 or 3 pct Sn or Zn additions on SDC and other properties were assessed. Trials were conducted on consolidating rings and gears of the 65Mn-35Cu alloy on industrial-type P/M equipment.

Jan 1, 1979

By Mark Sheppard

The technical literature on the general subject of crushing contains many references to the work of investigators on the laws governing, and the factors entering into, the economical production of fine materials. In fine grinding, whether for the purpose of producing fine material, or for the unlocking of minerals in an ore, close control of the screen sizes of primary-crusher products is of secondary consideration and accordingly has received very little attention. The growth and development of the nonmetallic industries, however, have drawn more attention to primary crushing. Many of these industries are interested in the production of relatively coarse products that meet certain definite size specifications, a condition entirely different from that existing in the field of ore dressing. Under such conditions, a knowledge of the factors governing the selection Paid operation of primary-crushing equipment is essential to the economical production of a satisfactory material.

Jan 1, 1939

By Geo. S. Krueger

This paper, describing mining methods and costs at the Judge mine Park City, Utah, is one of a series being prepared by the Bureau of Mines on mining practices in the United states. ACKNOWLEDGMENTS The writers acknowledge the assistance of E. D. Gardner, supervising engineer, Southwest Experiment Station, Bureau of Mines; Paul H. Hunt, mine manager, Park Utah Consolidated Mines Co.; Wm. Osika, chief mine accountant; and Eric Neilson, assistant master mechanic of the mine.

Jan 1, 1938

By Gary Friedline

As a consequence of the Coal Mine Health and Safety Act of 1969(PL91-173), the Bureau of Mines (BOM) entered into a contract with Ocean Energy Inc. (OEI) to develop, fabricate, install, and evaluate a permissible lighting system for use on a longwall coal mining operation. The program schedule is shown in Figure 1.1. The proposed regulations are contained in Appendix A. The initial part of the program involved a survey of existing longwall lighting practices in Germany and England and an evaluation of a variety of lighting components on a mockup of a longwall mining operation that was fabricated under this program. Visits made to German and British mines uncovered major differences in lighting level requirements, permissibility aspects, size, and operating constraints which identified wide disparities and essentially eliminated from further consideration any known imported lighting devices for meeting the higher lighting levels and standards proposed for US coal mines by the Mining Enforcement and Safety Administration (MESA). The longwall mockup provided use¬ful information regarding the amount of illumination required, physical size and shape of lamps, light distribution problems, cable routing, use of connectors, signaling, glare, and other important factors unique to the lighting of low coal longwalls.

Jan 1, 1975

By William L. Crentz

In a Nation-wide appraisal of coking-coal reserves and of the practicability of upgrading marginal deposits to metallurgical standards, this study of the preparation characteristics of the coals in Cambria County, Pa. , was undertaken. Over 90 percent of the coal remaining in Cambria Comity is found in the Upper Freeport, Lower Freeport, Upper Kittanning, and Lower Kittanning beds. The Middle Kittanning bed, although mined on a commercial scale in the past, is not an important bed now, as most of the remaining reserves are too thin to be mined over wide areas. For many years, Cambria County has been an important source of coal for industrial and metallurgical purposes. The) principal production comes from the Lower Kittanning bed, which accounts for almost .60 percent of the Cambria County coal output. Table 1 shows the county's coal production, by beds, during 1948.

Jan 1, 1950

By Donna L. Anderson

This U.S. Bureau of Mines report describes a system to determine the position and heading of a continuous mining machine during the maneuvers required at the face area of a mine. The system consists of commercially available angular position sensors and a computer interface developed and tested at the Bureau. The sensors employed are laser-based scanning devices that report the angular location of retroreflective targets within their 90° field-of-view. The targets are mounted on the continuous mining machine; the laser scanners are mounted on an external reference structure. The computer interface consists of a single-board computer-controller programmed to gather and process the angular position information, and to calculate the machine's position and heading relative to the reference structure. A sensor fusion algorithm will be incorporated into the computer interface programming to increase the accuracy and reliability of the system.

Jan 1, 1989

By J. E. Murphy

The u.s. Bureau of Mines investigated electrode designs for electrowinning lead metal from a LiCl-KCl-PbCI2 electrolyte at 4500 C. The major objective of this investigation was to decrease the energy requirement for lead electrowinning. Electrolysis was performed in a bench-scale cell using several graphite electrode assemblies. Such parameters as electrode spacing, current density, and chlorine gas removal from the anode were investigated in the bench-scale tests. An optimum electrode assembly, termed the sawtooth design, was scaled up and operated at 3,000 and 4,000 A. The sawtooth electrodes operating at 3,000 A produced lead for 0.66 kW·h/kg. The electrodes were constructed by cutting large triangular grooves in the electrode surfaces. The electrodes were placed together such that the triangular peaks of one electrode projected into the triangular valleys of the other electrode. Chlorine did not build up on the anode with the sawtooth electrodes.

Jan 1, 1991

By D. E. Pollock, J. A. Organiscak

Water sprays and water powered scrubbers have both been utilized in the mining and milling industry to suppress airborne dust. Unconfined water sprays operated at lower water pressures of ?689 kPa (?100 psig) can be very effective at wetting the mine product at the dust source and significantly reducing the amount of respirable dust that becomes airborne. However, unconfined waters sprays can be somewhat ineffective in actually removing airborne dust from the air. On the other hand, water powered scrubbers operating at higher water pressures of ?1,724 kPa (?250 psig) in physical enclosures or ducts have previously been demonstrated to be very effective in removing airborne dust from the air. These higher operating water pressures are uncommon in many mines and mills, so their use is limited. The National Institute for Occupational Safety and Health (NIOSH) recently investigated the performance of a lower-pressure, water powered inline series spray scrubber for removing localized airborne dust emitted at the source. Results showed noticeable improvements in airborne dust capture efficiency through the operation o f multiple inline series hollow cone spray nozzles within a round duct or pipe at the same water pressure as a single spray. Operating hollow cone spray(s) at higher water pressures noticeably improved airflow through the scrubber and yielded some additional scrubber efficiency improvements. Thus, in-line spray scrubber efficiency trade-offs were observed to be made by altering spray power components of water pressure and/or quantity (number of sprays). Results show that, on average, up to 0.23 and 0.32 m3/s (484 and 679 cu ft per min) of airflow at 0.81 and 0.69 dust capture efficiencies can be achieved with three 81° and 33°hollow cone inline series sprays, respectively, operating at 1,655 kPa (240 psig).

By Karl C. Dean

All components of 15 automobiles manufactured between 1954 and 1965 were analyzed, and it was determined that a representative junk automobile would have the following composition (all figures in pounds): steel, 2,532; cast iron, 511; copper, 32; zinc, 54; aluminum, 51; lead, 20; rubber, 145; glass, 87; miscellaneous, 142. Time and motion studies and a cost evaluation were made to determine if such a typical vehicle could be economically burned in a smokeless incinerator and hand-dismantled, and if the resultant steel could be baled into a high-quality No. 2 bundle containing less than 0.10 percent copper. The cost evaluation showed that processing the composite car would cost about $51 to produce about $56 worth of marketable ferrous and nonferrous metal products and provide an annual rate of return on investment of 19 percent.

Jan 1, 1969

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By C. E. Wood

A special appropriation made by Congress in July 1940 provided funds for the investigation of methods for recovering manganese from low-grade [ ] domestic deposits. These funds were assigned to the United States Department of the Interior, Bureau of Mines. A committee, identified as the Technologic Committee on Manganese of the National Research Council, National Academy of Sciences, was appointed to recommend the allocation of the funds for investigation of the more promising projects.

Jan 1, 1942

By Kenneth H. Johnston

Records show that waterflooding was tried in Osage County as early as 1934, but it was not economically important until a large unitized flood in the North Burbank field was begun in 1950. Development was rapid and by the end of 1960, there were 70 active water flood projects and 16 active pressure-maintenance projects in the County. The locations and status of the water-flood and pressure-maintenance projects in Osage County on December 31, 1960 are shown in figure 1, and information pertaining to these projects as of July 1, 1960 is given in table 1. For the past several years, Bureau of Mines petroleum engineers have arranged tours of selected waterflooding projects for the spring meeting of the Kansas-Oklahoma Water flood Association. These tours are conducted to demonstrate unique operating methods and new field equipment and to provide additional opportunities for exchanging information. Each of these tours has been supplemented by a published report describing in detail the projects visited. This report has been prepared for distribution during the 1961 spring tour of three waterflooding projects and a pressure-maintenance project in Osage County, Okla. (fig. 2).

Jan 1, 1961

By E. K. Stanek

This research study was performed on a case study basis and can be divided into two parallel thrusts: electrical and thermal energy conservation. Energy consumed annually in mining and refining operations represents about 6% of the 80 quadrillion Btu's consumed nationally. In the electrical portion of the study, five areas were addressed: optimal dispatching of on-site generation, high-efficiency motors, conductor selection, power factor correction, and high efficacy lighting. In the case study mine which has a multiple unit on-site generation system, optimally dispatching units can save significant energy. The other four methods are difficult to justify on a retrofit basis due to capital costs. In the thermal portion of the study, a thermodynamic analysis was performed on the reverberatory smelting process possible areas of energy conservation were identified as radiation and convection heat losses from the furnace arch and the dumping of high energy content smelting slag. It has been shown that materials currently available can provide the means of reducing heat loss from the reverberatory furnace. It has also been shown that a significant amount of energy may be recovered from the slag. However, these are both subject to further study and validation.

Jan 1, 1982

By William W. Adams

A general increase in employment prevailed in the stone-quarrying industry of the United States during 1941 compared with 1940. Likewise, more accidents occurred to men working in and about the quarries, with the result that the accident-frequency rate for the industry as a whole was higher in 1941 than in the previous year. Reports from operating companies to the Bureau of Mines, covering open and underground quarries, as well as rock-crushing and rock-dressing plants, cement mills, and limekilns at or near the quarries, showed a total of 86,123 men employed and a total of more than 22 million man-days of labor performed during 1941. The total working time of the industry averaged 260 days per man. Measured in man-hours, the volume of work equaled 173 million, an average of 2,011 man-hours per employee.

Jan 1, 1943

By A. E. Raddatz

In an attempt to develop technology to use domestic resources in place of imported bauxita, the Bureau of Mines investigated sulfurous acid leaching to extract alumina from kaolin. The process consists of leaching the calcined kaolin with a 30 wt-pct S02 solution at 60° C and 160 psig for 17 hours, fil¬tering the leach slurry, precipitating monobasic aluminum sulfite from the filtrate at 110° C and 60 psig, a& decomposing the sulfite in the spent liq¬uor at 150° C and 55 psig to produce crude alumina. Purification of the crude alumina was accomplished using a modified Bayer process. Results from closed-circuit tests employing the sulfurous acid process showed that overall extraction of alumina from kaolin was 67 pct. Production of 1 ton of alumina would require 3.6 tons of calcined kaolin, 0.7 ton of sul¬fur dioxide, and 8.4 tons of water. After purification by a modified Bayer process, the alumina product contained the following; impurities, expressed in weight-percent: Fa203, 0.009; S, 3.6; Si02, 0.07; Ti02, 0.002; K20, 0.017; and P205, 0.03.

Jan 1, 1981

By Raja V. Ramani

The potential usefulnuss of reclaimed surface-mined land has received much attention in recent times. This attention is partially due to the establishment of federal environmental reclamation standards but concern for achieving better land uses has also been shown by interested members of the mining industry. In an effort to develop a procedure for evaluating postmining land use potentials, specific mines in various regions of the U. S. were studied to determine the extent of current mined-land planning and to discover characteristics that are regional in nature. As part of this investigation, a 430-acre surface mine in Clear-field County, Pennsylvania has been studied. Established site planning principles have been applied to the case study site including formation of a data base, development of alternate land use plans, and evaluation of the economic, environmental, and social impacts of the land use alternatives. Key factors affecting site realization have been identified along with positive suggestions for applying land use planning processes to mined-land planning.

Jan 1, 1983

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was clone through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will he useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetimes. This report is in two volumes: Volume l - Technical Report Volume 2 - Design, Inspection, and Maintenance Manual

Jan 1, 1977

By J. Bruce Clemmer

[Gypsum is one of the mo .. t iJf.l)ortant nonmp.tal1.ic T!1inerals, as is indicat-? ed by the fact that tlle Uni ted states cO!1sUl:Ied p, roximn..tely 3,500,000 tons of natura.l and calcinecl e::,j;-psum in 1937. The b\.'.ilr:.in.; traces \"fe.ro the largest users and required 2,520,000 tons of calcine for the r-roductiop. of plaster,]

Jan 1, 1941