Search Documents

By N Vijay Mohan, K V. Balamukund, G Ananth Ramulu

Jointing of steel rods in reinforced concrete structures needs careful consideration as it renders the structure weak at the joint. The jointing is usually done at sections of structural members, where the bending moment and shear force are least. Jointing is done either by overlapping the rods or welding or by mechanical splicing. A novel method of jointing them is by inserting the two rods in a steel sleeve and cladding it on to the rods by subjecting the sleeve to explosive energy. A rod jointed in this fashion is tested for direct tension and bending when used in a reinforced concrete beam. The test results show that it is an effective method. The advantage is that a number of joints can be made in a single operation.

Jan 1, 1993

By J Foklesi, G Bohus, D Benedek

The breakage process in blasting takes place in space and in time and the latter will determine the degree of fragmentation, shape of the muckpile and the extent of displacement. The shock wave travels at the velocity of sound in the material and it can easily be measured. The cracks' velocity is only 0.38 % of the velocity of sound. The number of cracks at any distance from the explosion cavity, their length and the time of development can be calculated.

Jan 1, 1986

By Bin Feng, Xiang Fang, Tao Guo, Fandong Lu

Abstract: Rough set theory (RS) can find useful information from a large number of data and generate decision rules without prior knowledge. Support vector machines (SVM) have good classification performances and good capabilities of fault-tolerance and generalization. To effectively control blasting vibration effect, prediction model of blasting vibration parameters based on rough sets and support vector machines are established. Particle swarm algorithm (PS) is used to dynamically discretize attributes. Then, according to the optimal particle calculated by the PS algorithm, the decision table is established. After eliminating less importance attributes and data, then SVM is trained and established for prediction. The model can deal with both quantitative and qualitative factors such as aperture and cast direction, and analyze their importance to peak vibration acceleration value. The improvement of prediction accuracy is verified by testing data.

Jan 1, 2014

By Robert Hopler

The 1800’s were a time of tremendous advancements in science and experimentation, and earthquakes were a subject of great interest. The meetings of the British Association for the Advancement of Science in 1853 and 1854 are good examples of this. The proceedings of the Association for the 1854 meeting includes a table entitled “Catalogue of Recorded Earthquakes from 1784 to 1850” which takes up 326 pages, and lists available information on approximately 3000 earthquakes. The 1853 proceedings have a similar table for earthquakes recorded from 1606 B.C. to 1783. In the 1854 volume there is a “Report of the Committee on Earthquakes,” which provides us with a view of the general state of the science. Excerpts from that report follow:

Jan 1, 2006

By Alain Blanchier

Because in Europe and in many other countries as well every new project (quarry, mine, public work) needs a risk estimation to prove its feasibility, a model to estimate flyrock risks became necessary. This paper presents the basic hypothesis which should underlay such a model to estimate statistical flyrocks range for not only some single blasts but a whole project and in particular the way to take into account rockmass or blast pattern parameters variability. It describes a first usable quantitative flyrock model based on the characteristics of the blasting plan and of the generic laws utilised in casting and selective blasting operations and on a statistical approach of rockmass. In a second step, this paper discuss an approach of risks estimation compared to the classical one used in pyrotechnics studies for explosive magazine risks assessment.

Jan 1, 2013

By P Wapner, C Lo Edwards, S CO Schmidt, J N. Johnson, R Oliver

Shale oil recovery rates that can be achieved in underground in situ retorts can be strongly influenced by the shale breakage and fragment-size distribution achieved during rubblization. Since the fragmentation pattern in the retort is a direct result of the blast design used for rubblization, the characterizing blast parameters should be carefully selected. Explosives should be matched to the host material and blast geometries properly chosen so that the required fragmentation results are achieved at optimum costs. Special attention must be directed to selecting blast parameters that produce uniform bed permeability, suppression of fines, proper fragment size distribution, and minimal damage to the retort walls and ceiling. The influence of joints and natural fractures should also be known. In instances where the requisite blasting parameters are unknown, they should be determined from test blasts.

Jan 1, 1979

By John Brennan

The Avalauncher has been an integral tool for avalanche mitigation work for close to 50 years. With their ability to place a kilogram of high explosives up to two thousand meters away, they routinely serve as a short range alternative to military artillery. The Avalauncher’s roots can be traced to a pneumatic baseball pitching machine used by Major League Baseball teams in the United States in the late 1950s. Throughout the decades, many modifications have been made to both the launcher and its projectiles. Current technology has allowed the Avalauncher to attain greater accuracies and operational range. In this paper I plan to cover not only the history of the Avalauncher but also explore its potential future.

Jan 1, 2009

By Salah A. Taqieddin

Blast casting or trajectory blasting, as it is sometimes called, is an innovative mining technique that has been receiving increasing acceptance among operations of surface coal mines and quarries as a means of offsetting the rising cost of mechanical excavation of overburden with a high overburden-to-ore ratio. Many similarities exist between geological characteristics of overburden formations of phosphate beds and the formations that conceal coal seams. Both are sedimentary origin and are removed for mining in an identical manner (i.e. use of a dragline or shovel to strip or cast the overburden aside).

Jan 1, 1997

By John P. Ashby

Production blasting is a process of destruction of rock masses in order that ore may be extracted. Many open pit operations are faced with the apparently conflicting requirements of providing large quantities of fragmented rock for the processing plant and of minimizing the amount of damage inflicted upon the surrounding pit slopes. A reasonable compromise between these two conflicting demands may often be found by means of simple engineering of production blasts.

Jan 1, 1980

By Courtney Vallejo, Rafiqul Tarefder

This study examines the effects of small scale airblast experiments on cohesive soils and the resulting ground vibrations and crater geometries. Relationships for ground vibration attenuation with soil depth and distance from the blast source were developed. The study is part of a broader research topic of understanding the vulnerability of earthen embankment dams to blast loading. Many earthen embankment dams in the United States were constructed more than fifty years ago and were not designed to withstand high-stress loading such as blast loading. These structures may be susceptible to failure and it is important to describe the response of the earthen dam during a blast event.

Jan 1, 2013

By Doug Wathen, Philip M. E Thomas

The City of Fort Myers needed to replace a 40-year old 42-inch storm sewer line in downtown Fort Myers with a new 54-inch line to accommodate population growth. The old line had to be kept operational while a new line was installed. the contractor spent two months using a drop ball, a hoe ram, and large rippers trying to break the three to four feet of rock that needed to be removed to accommodate the new pipe. Mechanical trenching was considered but was proven to be overly expensive. On very short notice, Ireco of Florida was asked to design and execute a blasting procedure that would allow this project to proceed. Nearby buildings were over 80 years old, three of them containing antique shops specializing in glass antiquities with attorney offices above them. High water table compounded problems with a 20-year old steel water main and clay drainage pipe 15 feet from the new sewer line. Holes had to be drilled within six inches of the edge of the existing pipe to four feet below the pipe on either side of the pipe and blasted. No interruption in the sewer line flow was to be tolerated.

Jan 1, 1996

By Zheng Deming, Li Hongwei, Lei Zhan, Dai Chunyang

This paper introduces the application of a digital electronic detonator in the demolition blasting of largescale (LS) and long delay time (LDT) frame-shear structure buildings. The whole building to be demolished by blasting is an L-shaped frame shearing structure. Some parts of these buildings have a large length along the direction of collapse, so the detonation delay of the column is longer. To ensure the building is successfully blasted and demolished, a digital electronic detonator detonation system is adopted. In the design of the detonating network, full use is made of these characteristics of the digital electronic detonator, such as flexible installation, high precision of delay before blast, and dedicated testing equipment to check the reliability of the network. These advantages ensure the damage of the load-bearing structure is within the blasting gap and that the accuracy of the collapse time of the building, which not only guarantees the collapse effect of the building, but also provides strong technical support for improving the intrinsic safety of the blasting operation and the supervision of the flow direction of the detonation, these research be provide reference for the application of digital electronic detonators in similar projects.

Jan 1, 2019

By Joseph Meyers

Explosives techniques and technology are constantly evolving and improving, yet basic communication and business skills are not being used regularly. Many potential blasting projects never occur due to simplistic, basic factors, such as a lack of communication. Articulate communication is the key component in the blast approval process, which has changed remarkably from how business was conducted fifty years ago. Imperative to the approval process is communication outlining the safety and benefits of the blasting project. Information and transparency with the stakeholders and the Authority Having Jurisdiction (AHJ) will greatly improve the chances of having a blasting project approved. This open communication starts at the inception of the project when the memorandum of understanding (MOU) is obtained, and involves the AHJ through all steps of the approval process. The blasting industry and regulators must work collaboratively to improve safety, security, regulations and licensing. Implementing state of the art blasting techniques, security, safety measures, vibration monitoring and strict licensing allows the AHJ and all stakeholders to remain integrated and informed, contributing to process approval. Regulatory operators should strive to achieve success thru communication, cooperation and compliance which is accomplished thru continued education and transparency. These steps, combined with regular meetings, has proven to be a benefit to both industry and regulators. Relationships are built through trust, teamwork, transparency and communication –including the take holders and AHJ in the approval process from the inception solidifies these relationships and improves teamwork

By Alan Minchinton, Ian Kirby, Jim Chan

It has long been known that successful blasting in soft and hard rock can require the use of different explosives. While choosing an explosive of the right energy density is important, the dynamics associated with non-ideal detonation behaviour play an equally major role. Tuning the energy release rate of an explosive to optimise its blast efficiency can be likened to tuning an internal combustion engine to improve its performance.

Jan 1, 2014

By T Guiliani, F Ottuonye

Explosives casting is gaining increasing popularity as an overburden removal method in strip mining because the coats of using explosives to cast a percentage of the overburden to the spoil are lower than the costs of using stripping shovels or draglines to do all the overburden removal. This is due to the rising capital and operating costs of draglines and shovels.

Jan 1, 1989

By Quian Liu

The problem of cross-hole explosive malfunctioning in rock blasting (including sympathetic detonation, desensitization and cut-offs) is a function of delay and spacing in a blast which should be designed to avoid such occurrences. On a delay-spacing chart, the phenomenon of explosive malfunctioning is explained by dividing the chart into different regions, while the shape and size of each region could vary from one explosive to the other. Over seventy blasts have been carried out at the CANMET Experimental Mine to identify the malfunctioning characteristics of specific emulsion, water-gel and dynamite explosives. In each experiment, two parallel blastholes, 32 mm in diameter and 1.7 m deep, were drilled downwards in an underground drift.

Jan 1, 1994

By Sushil Bhandari

Presented here is the simplified process of fragmentation of homogeneous rocks by blasting based on experimental studies. Small scale single hole blasting experiments on jointed limestone are described. Results show that directions of joints overshadow the degree of fragmentation and also influence the remaining rock. The possible influence of joints on the process of fragmentation of non-homogeneous rock by blasting is also discussed.

Jan 1, 1983

By C James Dahn

A new generation of high performance and high density ammonium nitrate prills have been developed. These cycled "prills" offer significant improvement in ANFO mixing time, detonation velocity performance, and heaving capabilities. In addition, their safety characteristics are better than standard ANFO explosives.

Jan 1, 1980

By Gerald R. Coonan

Laboratory research is being conducted to substantiate suggested levels for voluntary standards on human response to transient vibration. The application of those findings to actual field conditions, however, will be limited because they will not include social and psychological factors existent in the real world. It is necessary, therefore, to examine available empirical information on complaints in an attempt to define the influence social and psychological factors might have on the laboratory results.

Jan 1, 1982

By Clarence Zink

Aside from the mechanical properties and process of actual rock breakage, rotary drill bit performance is affected by several “post breakage” items: cuttings size, flushing air pressure, flushing air volume, cuttings load, drill hole geometry, etc. We all recognize that more efficient drilling creates bigger cuttings, more air pressure cleans the hole bottom better, more air clears the cuttings from the hole, and a better hole geometry allows cuttings to escape with a minimum of “regrind”.

Jan 1, 2006